Osprey Camera Operator & Installation Manual
Contents
1. Statements Throughout the manual certain potential problems or further information relating to the installation maintenance understanding or use of the apparatus will be highlighted to the operator by indications identified by the adjacent symbol and text Throughout the manual certain safety or operational related comments and requirements will be highlighted to the operator by indications identified by the adjacent symbol CAUTION and text Throughout the manual certain safety or operational related comments and requirements that could lead to injury or loss DANGER of life will be highlighted by the adjacent symbol and text Technical Support Contact your local agent or Tritech International Ltd Tritech International Ltd Peregrine Road Westhill Business Park Westhill Aberdeen AB32 6JL UK Telephone 444 0 1224 744111 Fax 444 0 1224 741771 Email support tritech co uk Web www tritech co uk An out of hours emergency number is available by calling the above telephone number If you have cause to use our Technical Support service please ensure that you have the following details at hand prior to calling e System Serial Number if applicable e Fault Description e Any remedial action implemented Due to the expansion of equipment capabilities and the fact that new sub modules are continually being introduced this manual cannot detail every asp2. where a defect has been caused by isolation incompatibilities The warranty does not cover the transportation of personnel and per diem allowances relating to any repair or replacement The warranty does not cover any direct indirect punitive special consequential damages or any damages whatsoever arising out of or connected with misuse of this product Any equipment or parts returned under warranty provisions will be returned to the customer freight prepaid by TIL The warranty shall become invalid if the customer attempts to repair or modify the equipment without appropriate written authority being first received from TIL TIL retains the sole right to accept or reject any warranty claim Each product is carefully examined and checked before it is shipped It should therefore be visually and operationally checked as soon as it is received If it is damaged in anyway a claim should be filed with the courier and TIL notified of the damage Note TIL reserve the right to change specifications at any time without notice and without any obligation to incorporate new features in instruments previously sold Note If the instrument is not covered by warranty or if it is determined that the fault is caused by misuse repair will be billed to the customer and an estimate submitted for customer approval before the commencement of repairs Issue 1 TIL Eng Spec 035 Page 5 of 15 Tritech International Ltd Osprey Camera OIM Safety
3. D_CAP MODULE FRONT PORT HOUSING CAMERA BODY CAMERA PSU PCB Parts list Front Port housing PCAM11 P01 Main Camera Body PCAM11 H02 Connector End cap PCAM11 H03 PSU Driver board PCAM11 PD3248 Water corrected port PCAM11 WP01 Camera module PCAM11 V07 Support camera module PCAM11 V00 Hardware Kit PCAM11 S1 O ring set PCAM11 R03 Comprising Connector End cap Front port housing Port retainer Lens holder Internal Issue 1 TIL Eng Spec 035 Page 12 of 15 Tritech International Ltd Osprey Camera OIM Appendix 1 Product Specification Issue 1 TIL Eng Spec 035 Page 13 of 15 Tritech International Ltd Osprey Camera OIM Appendix 2 Osprey Camera Pin Configuration Issue 1 TIL Eng Spec 035 Page 14 of 15 Tritech International Ltd Osprey Camera OIM Appendix 3 Circuit Schematics Issue 1 TIL Eng Spec 035 Page 15 of 15
4. International Limited Please read this manual carefully before setting up and using your unit Osprey Camera Operator amp Installation Manual The electronic version of this document is the controlled copy Therefore all printed versions of this document are uncontrolled For the latest manual revision always visit www tritech co uk Supplied by Issue 1 TIL Eng Spec 035 Osprey Camera OIM COPYRIGHT Tritech International Ltd The copyright in this document is the property of Tritech International Limited The document is supplied by Tritech International Limited on the understanding that it may not be copied used or disclosed to others except as authorised in writing by Tritech International Limited Tritech International Limited reserved the right to change modify and update designs and specifications as part of their ongoing product development programme F063 1 Tritech International Ltd Osprey Camera OIM CONTENTS HANDLING OF ELECTROSTATIC SENSITIVE DEVICES 4 WARRANTY STATEMENT 5 SAFETY STATEMENTS 6 TECHNICAL SUPPORT 6 INTRODUCTION 7 OPERATING CONDITIONS 8 SETTING UP PROCEDURES 9 FOCUS 9 DISASSEMBLY PROCEDURE 10 Water Corrected View Port 11 ILLUSTRATION OSPREY 12 Parts list 12 APPENDIX 1 PRODUCT SPECIFICATION 13 APPENDIX 2 OSPREY CAMERA PIN CONFIGURATION 14 APPENDIX3 CIRCUIT SCHEMATICS 15 Issue 1 TIL Eng Spec 035 Page 3 of 15 Tritech International Ltd Osprey Camera OI
5. M HANDLING OF ELECTROSTATIC SENSITIVE DEVICES Attention Observe Precautions for handling Electrostatic Devices Caution Handling of Electrostatic Sensitive Devices Certain semiconductor devices used in the equipment are liable to damage due to static voltages Observe the following precautions when handling these devices in their unterminated state or sub units containing these devices e Persons removing sub units from any equipment using electrostatic sensitive devices must be earthed by a wrist strap via a 1MQ resistor to a suitable discharge reference point within the equipment Soldering irons used during any repairs must be low voltage types with earthed tips and isolated from the Mains voltage by a double insulated transformer Care should be taken soldering any point that may have a charge stored Outer clothing worn must be unable to generate static charges Printed Circuit Boards PCBs fitted with electrostatic sensitive devices must be stored and transported in appropriate anti static bags containers Issue 1 TIL Eng Spec 035 Page 4 of 15 Tritech International Ltd Osprey Camera OIM WARRANTY STATEMENT Tritech International Limited herein after referred to as TIL TIL warrants that at the time of shipment all products shall be free from defects in material and workmanship and suitable for the purpose specified in the product literature The unit system warranty commences immediately from the da
6. SASSEMBLY PROCEDURE Maintenance of water integrity is the responsibility of the user Internal damage caused by water ingress is not covered by product warranty CAUTION unless the cause can clearly be identified as a manufacturing defect It is recommended that all o rings and back up rings be replaced whenever the camera is opened to avoid water ingress CAUTION It is not advisable to open the camera unless absolutely necessary Extreme care must be taken when reassembling to avoid fouling the pressure seals It is recommended that all o rings and back up rings be replaced whenever the CAUTION camera is opened to avoid water ingress To access the internal part of the camera Pull off the nylon cord retaining the front port housing to the camera body rotate fully anticlockwise the front port housing as if you were adjusting the focus and gently pull out of the main camera body as straight as possible If the camera body is not fully free from the lens then the lens will pull out of the front port housing were it is retained by an O ring In that case unscrew the lens completely and insert it back in position in the front port housing by applying pressure to pass the O ring When the front port housing is disassembled pull out the nylon cord retaining the connector end cap and pull out the electronics Disconnect the small connector at the back of the camera module to gain access to the PSU and video ampl
7. ect of the operation Issue 1 TIL Eng Spec 035 Page 6 of 15 Tritech International Ltd Osprey Camera OIM Introduction The Osprey colour camera incorporates the latest design in CCD technology A camera power supply board provides all the necessary voltages for the camera module A line driver compensates attenuation of the video signal as it passes through the umbilical A water corrected port is fitted to optimise the picture quality The integration of this package provides an extremely robust unit that will push forward the limits of resistance in harsh environments Issue 1 TIL Eng Spec 035 Page 7 of 15 Tritech International Ltd Osprey Camera OIM Operating conditions The camera is compatible with any video recorders or monitor working with PAL standard or NTSC standard depending on the module version purchased Module selected at time of ordering The camera should not be used out of the limit conditions specified in this manual For any special requirement please contact TRITECH INTERNATIONAL LTD Before attaching the connector to the camera ensure it is clean and lightly smear the male connector pins with silicon grease The power supply is polarised Please ensure that the correct polarity is used before switching on the unit The camera is designed for use under water Water has a cooling effect on the camera which means that it will become hot when operated in air It is acceptable to ru
8. ifier board If required fit the solder bridge on the right position to obtain the gain level required for the video signal Before reassembling inspect the O rings for damage if possible replace them Clean and lightly smear the o ring with appropriate silicon grease e g MS 33 prior to fitting To reassemble the camera follow the disassembly in the reverse order Particular attention is to be made to the o rings when rebuilding the camera A small cut is enough to lose watertight integrity CAUTION Issue 1 TIL Eng Spec 035 Page 10 of 15 Tritech International Ltd Osprey Camera OIM Water Corrected View Port To disassemble the water corrected port unscrew the front port housing and remove it Remove the lens from the front port housing Extract the front view port retaining cord The acrylic view port can now be removed by pressing or tapping out from behind Use a blunt instrument and soft cloth to prevent damage to the port surface Before re assembly inspect the O ring for damage clean and lightly smear it with silicon grease It is recommended that a new O ring is fitted whenever the front port is removed To readjust the focus after disassembly rotate the front port housing clockwise until the preferred focus point is reached Issue 1 TIL Eng Spec 035 Page 11 of 15 Tritech International Ltd Osprey Camera OIM ILLUSTRATION OSPREY 107 0 CONNECTOR EN
9. n the camera in air for testing or repair purposes however unless a considerable heat sink is used it is not recommended that the camera be left to operate in air for extended periods as the life of the camera may be reduced An internal solder splash jumper is fitted on the PSU Driver board to boost the video signal if required Issue 1 TIL Eng Spec 035 Page 8 of 15 Tritech International Ltd Osprey Camera OIM Setting up Procedures The power supply output is controlled through a regulator It is set at the factory and does not require any further adjustment If for any reason the output voltage for the camera is not present the regulator would have to be replaced If it is required to drive a long coaxial cable on your application you must move the solder splash visible on the PCB printed circuit board to the opposite location this will fit the compensation for the long line amplifier in circuit FOCUS Focus adjustment is done by rotating the front port housing by small increments while holding firmly the camera body in your hand until you find the right setting Normally no more than 1 turn in each direction will be required If the port view is rotated fully clockwise or anticlockwise no damage will be done but it may be necessary to disassemble the front port housing from the body of the camera to free the lens Issue 1 TIL Eng Spec 035 Page 9 of 15 Tritech International Ltd Osprey Camera OIM DI
10. te of customer acceptance and runs for a period of 365 days Customer acceptance will always be deemed to have occurred within 72 hours of delivery Note Any customer acceptance testing if applicable must be performed at either TIL premises or at one of their approved distributors unless mutually agreed in writing prior to despatch Conditions These include but are not limited to the following 1 The warranty is only deemed to be valid if the equipment was sold through TIL or one of its approved distributors 2 The equipment must have been installed and commissioned in strict accordance with approved technical standards and specifications and for the purpose that the system was designed The warranty is not transferable except or as applies to Purchaser first then to client TIL must be notified immediately in writing of any suspected defect and if advised by TIL the equipment subject to the defect shall be returned by the customer to TIL via a suitable mode of transportation and shall be freight paid The warranty does not apply to defects that have been caused by failure to follow the recommended installation or maintenance procedures Or defects resulting from normal wear amp tear incorrect operation fire water ingress lightning damage or fluctuations in vehicles supply voltages or from any other circumstances that may arise after delivery that is out with the control of TIL Note The warranty does not apply in the event
Download Pdf Manuals
Related Search