User Manual
Contents
1. If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions Safety Information Please read the below notes before use the monitor set and keep it well for future reference a Use only a power source and connection appropriate for the monitor as indicated on the marking label b Slots and openings in the cabinet are provided for ventilation these openings must not be blocked or covered Never push objects of any kind into cabinet slots or other openings c Never insert anything metallic into the monitor openings Doing so may create a danger of electric shock d To avoid electric shock never touch the inside of the monitor Only a qualified technician should open the monitor case e Unplug the monitor from the wall outlet before cleaning Do not use liquid cleaner or aerosol cleaners Use a damp lint free cloth for cleaning Install the monitor near an outlet that you can reach easily Disconnect the product by grasping the plug firmly and pulling in from the outlet Never disconnect it by pulling the cord Accessories Please check the following listed accessories before installation AC adapter AC Lead VGA cable Audio cable Installation 1 Rear Interface VGA S VIDEO BNC IN BNC OUT gt IN OUT u eo fig 1 1 DC 12V Use only the power supply included with the monitor 2 VGA For connection to a standard PC 3 S Video2. In For connection to a standard S Video source 4 BNC IN Connection for composite video 5 BNC OUT Composite video loop through 6 AUDIO IN OUT PC audio in and loop out Controls amp Functions 1 Front Control SELECT press this button to change input modes such as VGA AV etc Power press this button to turn on or off the unit and to turn up or down the volume and move up and down or left and right direction under setup interface Menu Pressing the MENU button calls up the On Screen Display The functions and menu screens differ according to the input mode Basic OSD setup 1 OSD setup under VGA input mode a Press MENU button to access Main Menu setting interface b Press A and V to select the desired submenu total six sub menus c Press MENU again to enter the submenu d Use lt and gt to adjust the parameter value e Press EXIT to exit the setup or return to previous interface Note the setting interface only available when connected with computer Ir 1 enter Main Menu interface by Color pressing once MENU button Press and V to select the desired option total six options Press MENU again to enter sub menu OSD Menu Select the Exit to exit Image Setting Position Main Menu Misc Exit 1 Enter Color setup interface in the main menu 2 Press aand v to select the desired option and then Press MEN
3. Colour TFT monitor VLCD15P VLCD17P VLCD19P User Manual Safety Statement This equipment has been tested and found to comply with the limits of a class B digital device These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However t here is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television which can be determined by turning the equipment off and in the user is encouraged to try to correct the interference by one or more of the following measures e Reorient Relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer of an experienced radio MONITOR technician for help Caution To comply with the limits for a Class B computing device always use the shielded signal cord and shielded power cord supplied with this unit Caution to the User The dealer warns the user that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
4. U to enter this item Color Adjust 3 Adjust parameter of the correspondent options to the desired value by pressing lt and gt Contrast and brightness 0 100 Color adjust Red Green Blue Exit Color temp 9300 6500 5800 SRGB USER 4 Select Exit to exit current oper v Contrast Brightness y f s er Color Temp G Enter Image Setting setup interface in the main menu Clock Press aand vto select the desired option and then Press MENU to enter this item Phase Adjust parameter of the correspondent options to the desired value by pressing lt and gt clock adjust from 0 100 Exit phase 0 63 Select the Exit to exit Image Setting Enter Position setup interface in the main menu Press aand vto select the desired option and then Press MENU to enter this item ae Adjust parameter of the V Position correspondent options to the desired value by pressing lt and gt H position can adjust from 0 198 and v position 0 20 Select the Exit to exit H POSITION Position Enter OSD Menu setup OSD H Pos interface in the main menu Press aand v to select the desired option and then Press OSD V Pos MENU to enter this item Adjust parameter of the correspondent options to the OSD Timer desired value OSD H V pos can adjust from 0 200 and OSD timer 0 27 Exit Select the Exit to exit OSD Menu 1 Enter Misc setup interface in
5. the main menu 2 Press nand v to select the desired option and then Press MENU to enter this item 3 Adjust parameter of the correspondent options to the desired value by Pressling nand v 4 Select the Exit to exit
Download Pdf Manuals
Related Search