3U Oakley Modular Series Overdrive User Manual and Builder's Guide
Contents
1. I have provided space for the three main control pots on the PCB If you use the specified Alpha 16mm pots and matching brackets the PCB can be held firmly to the panel without any need for additional mounting procedures The pot spacing is our standard for 3U modules 21mm The design requires plus and minus 12V or 15V supplies The power supply should be adequately regulated The current consumption is about 15mA for each rail Power is routed onto the PCB by a four way 0 156 Molex MTA type connector or 2 x 5 way 0 1 header The former is normally used by Frac based systems as well as our own 5U MOTM compatibles The latter is found on most Euro modular systems The four pins on the Molex MTA are 15V ground earth panel ground 15V The earth connection allows you to connect the metal front panel to the power supply s ground without it sharing the modules ground line More about this later As is common for our 3U series of modules the PCB has no mounting holes Components For general information regarding where to get parts and suggested part numbers please see our useful Parts Guide at the project webpage or http www oakleysound com parts pdf Some special considerations for this project The op amps are any high quality dual audio op amp The design has been tested with OP275G JRC4558 TL072 and OPA2134A All parts work very well but there are slight audible differences in the part selected for U1 I will ask the bui2. the pot for this purpose or get another one of similar size so that you can use the provided washer on the outside like you would normally Wire link Fit a small hoop of uninsulated wire resistor lead clipping into the two holes of LK This joins the two ground pins of the 4 way 0 156 header Miscellaneous Leaded Ferrite beads L1 L2 Double pole changeover switch SW1 2 4 way 0 1 Molex MTA header SKT And one of the following 4 way 0 156 Molex MTA header PWR For 15V systems 2x5 way 0 1 header PSU For 12V systems 3 5mm sockets Two off mounted off board You ll also need solder two lots of about 75cm of insulated multistrand hook up wire each of a different colour and a couple of cable ties You may well want to use sockets for the ICs I would recommend low profile turned pin types as these are the most reliable You need two 8 pin DIL sockets Circuit Description This module is probably one of the simplest we make and indeed if you have already looked at other overdrive circuits you may well recognise some of the features used in this particular design The module is powered in the conventional way from a split rail of 15V This comes in to the module via the 0 156 MTA connector PWR L1 and L2 in conjunction with C16 and C10 provide high frequency filtering and decoupling They essentially act to keep the power supply as free from noise as possible The main overdrive and distortion circuitry is
3. audio connections are via a four way 0 1 header on the PCB called SKT This may be different to other Oakley PCBs you may have built Doing it like this allows you to remove the board from the front panel easily and allows the potential for additional socket boards to be used in any future production run of the board You don t have to use a header in your PCB you can solder your wires directly to the PCB from the various socket lugs if you wish If you have used the little Cliff sockets you will see that they have four connections One is the earth lug or ground tag The second is the signal tag which will be connected to the tip of the jack plug when it is inserted The third and fourth tag are the normalised tags or NC normally closed lugs The NC lugs are each internally connected to the ground and signal tags when a jack plug is not inserted These connections should be automatically broken when you insert a jack Pushing a jack plug into an unconnected socket and looking carefully at the various contacts will reveal the actions of the NC lugs In this module we have no need for either of NC lugs 13 Use multistrand hook up wire to connect each socket lug to the relevant pin on the header Keep your wires short but not too short and you can use as many different colour wires as you can although I tend to use one colour because I m a minimalist There is absolutely no need to use screened cable for such short runs The connectio
4. diode clipping circuit there is some additional high frequency filtering based around the actions of R4 and C14 This low pass filter reduces the harshness and gives a rounded tone to the sound Coupled with the bass end roll off of C2 the overall frequency response over the distortion sections is focussed on the mid range part of the audio spectrum 11 The tone control is based around the classic TS and SD 1 design and is built around U3B Its a simple circuit that works well in practice and produces enough tonal variation to be very useful At the lowest setting of the Tone pot called timbre on the suggested front panel C1 acts in conjunction with R10 to produce a single pole low pass filter At the high end of the tone pot s travel C1 now mostly acts in conjunction with the feedback resistor R9 and R5 and produces a shelving high pass filter This boosts high frequencies and produces a much sharper sound This is particularly apparent in the distortion mode since this part of the circuit produces much more higher harmonics due to the more severe clipping affect The output of the tone control stage is fed to the other end of the balance pot called mix out on the front panel This is a simple arrangement that lets the user apportion the mix of distorted and straight through signal The relatively high impedance output of the wiper of balance pot would not be able to drive any other external modules direct so it is buffered and ampli
5. Oakley Sound Systems 3U Oakley Modular Series Overdrive Soft and hard clipping module User Manual and Builder s Guide V1 1 3 Tony Allgood B Eng Oakley Sound Systems CARLISLE United Kingdom Introduction This is the User Manual and Builder s Guide for the issue 1 Overdrive 3U module from Oakley Sound This document contains a basic summary of its operation a how it works section a full parts list for the components needed to populate the board and some basic testing methods For general information regarding where to get parts and suggested part numbers please see our useful Parts Guide at the project webpage or http www oakleysound com parts pdf For general information on how to build our modules including circuit board population mounting front panel components and making up board interconnects please see our Construction Guide at the project webpage or http www oakleysound com construct pdf The 3U Overdrive Module This is a simple but very effective waveform modifier module It has two basic modes selected by a switch Hard clipping is a hard edged distortion type effect useful for grunging up your signal Soft clipping is a more subtle effect and produces a clean sounding overdriven amp sound Three front panel pots control the sound Gain controls the overall gain of the pre amplifier stage and essentially determines the level of overdrive or distortion The timbre or tone control is an effective EQ cont
6. actually run from a lower 5V supply This is generated in the usual if somewhat overkill fashion of using two three terminal regulators U3 and U4 These generate a very stable quiet low noise split 5V rail which the more sensitive parts of the overdrive circuitry can run R15 and C20 and their negative equivalent provide additional filtering and isolation from main 15V rails D5 to D8 provide discharge paths during power up and down cycles which could potentially harm the ICs on the circuit The input signal is firstly attenuated by an inverting amplifier block based around U2A pins 2 3 and 1 This circuit reduces the input signal to around a quarter and provides the following sections with a constant source impedance Without this part of the circuit the overdrive core and the balance pot may affect the source signal s integrity and cause unwanted distortion if you were using the Overdrive module in parallel with another module U2A s output is then split one side going to the balance pot which will provide the dry signal and the other side going into the overdrive s core circuitry The core of the overdrive module is based around the same circuit as used in many guitar overdrive foot pedals To my knowledge this type of design first appeared in the Ibanez Tubescreamer TS 808 pedal but it also appears in other commercial pedals including the Boss OD 1 and SD 1 and other later Ibanez pedals The TS 808 pedal has become something li
7. also due to frequency shaping C2 rolls off the gain at lower frequencies C5 and the slew rate of the op amp act to curtail high frequency components It is these that set the width of passband that area in which the op amp acts as an amplifier In addition C9 will effectively block any DC signals to the amplifier The Oakley Overdrive has a major difference that the original TS doesn t have We can switch out the diodes completely and allow UIA to become an unlimited high gain amplifier But of course everything has limits and this time the output is limited by the supply voltage to UIA This is set by the 5V power supply and this causes the output to clip at around 4V for positive excursions and 4V for the negative The op amp cannot produce any output signal higher than this However when SW2 switches out the two diodes in the feedback path it also switches in via SW1 two more reverse parallel diodes D3 and D4 In conjunction with current limiter R4 these two diodes act as a traditional diode clipper and truncate the voltage across them to around 0 6V This is the distortion mode and two different types of clipping are now possible in this mode The diode clipping is apparent with high input signals with low gain or low input signals with high gain However at high gains with medium to high input levels both the op amp output limiting and diode clipping work together to give you a more pronounced effect Immediately after the
8. ding Honestly we would love to help but we do not have the time to help everyone individually by e mail Last but not least can I say a big thank you to all of you who helped and inspired me Thanks especially to all those nice people on the Muffwiggler s forum and Synth diy and Analogue Heaven mailing lists Tony Allgood at Oakley Sound Cumbria UK October 2009 updated July 2012 No part of this document may be copied by whatever means without my permission 16
9. fied by a simple inverting amplifier U2B R14 provides protection and stability for the output signal 12 Connections This 3U module comes with two power supply possibilities 1 Power connection PWR is the standard Oakley 4 way 0 156 MTA socket Friction lock types are recommended This system is backward compatible with MOTM and Blacet systems Power Pin number 15V 1 Module GND 2 Earth panel metal 3 15V 4 Note that the third pin is separate to the main module ground This is the standard Oakley power specification and allows for the front panel to be grounded to earth at the power distribution board rather than locally through the module However other than in Oakley modular systems it is not widely used See comment about the wire link below 2 Power connection PSU is the 10 pin Doepfer style power supply connection This is a 2 x 5 0 1 header and will fit 0 1 flat ribbon IDC sockets 12V goes to the top two pins of the header that is the ones nearest the legend PWR It is imperative that the power be supplied correctly Damage to the module will result if the power supply is connected up the wrong way For Fractional Rack and Euro sized systems please solder a small wire link into the board where it is labelled LK This connects the module ground and earth together and will make the module behave the same way as your other modules For assembly into Oakley 5U and 3U complete systems you can omit the wire link All
10. g gentle overtones to a solo synthesiser lead The actual input level is very important too The Overdrive module will produce much more strident results when the input level approaches 5V peak If the input signal is too weak then the resultant overdriven effect will be much less This means it is possible to get voltage controlled overdrive effects if you use a VCA in front of the module It is traditional to have the distortion after the final VCA In a fixed architecture synthesiser this is generally the only way you can do it But I find that using it between the VCF and the final VCA gives me right sounds for solo work The VCF will naturally vary the signal level as the cut off changes and having the VCA last will ensure that any additional hiss produced by the high gain amplifier in the overdrive module will be only heard along with the signal and therefore drowned out More complex sounds such as chords drum loops and so on will be far more effected than simple notes too The more varying frequencies that are present in the input signal the more distorted the output will appear Generally speaking if you are after subtle overdriven effects it is best to keep the input signal to just a few harmonically related notes The Overdrive PCB The PCB has double sided copper traces and features though hole plating The finish is Pb free and the board is made from glass fibre for strength The size of the board is 71mm deep and 83mm high
11. hat will fit their part number 75 0020 3U Overdrive Parts List The components are grouped into values the order of the component names is of no particular consequence A quick note on European part descriptions R is shorthand for ohm K is shorthand for kilo ohm For capacitors luF 1000nF To prevent loss of the small as the decimal point a convention of inserting the unit in its place is used eg 4R7 is a 4 7 ohm 4K7 is a 4700 ohm resistor 6n8 is a 6 8 nF capacitor Resistors 5 0 25W or better 47R 220R 1K 1K5 10K 15K 27K 33K 100K 360K Capacitors 10pF low K ceramic 47pF low K ceramic 47nF polyester 150nF polyester 220nF polyester 470nF polyester 100nF multilayer ceramic 2u2 63V electrolytic Discrete Semiconductors 1N4148 silicon diode Integrated Circuits 78L05 5V 100mA regulator 79L05 5V 100mA regulator OP275G dual op amp R15 R16 R5 R14 R2 R9 R4 RI R10 R7 R3 R6 R11 R8 R13 R12 C6 C17 C5 C15 C14 CI C2 C9 C3 C4 C7 C8 C11 C12 C16 C10 C19 C20 C13 C18 D1 D2 D3 D4 D5 D6 D7 D8 U3 U4 U1 U2 Onboard Pots All pots Alpha 16mm 47K Lin or 50K Lin BALANCE 100K Log GAIN 10K Lin TIMBRE The TIMBRE and BALANCE pots have space to mount pot brackets Note that when fitting the GAIN pot which has no pot bracket a shim washer should be fitted between the pot and the inside of the front panel You can use the washer provided with
12. it does very little other than overdrive the input signal it is a bit of a one trick pony If you like the trick then all is well if not it s time to move on Nevertheless it may be that the module is somewhat misunderstood After all the most common criticism with the module is that it doesn t actually do much In this perspective I wish to argue the case for its defence It actually does do a lot but it all depends on what sort of signal you are putting into it The Oakley Overdrive in its overdrive mode is quite simply a derivative of a famous overdrive guitar pedal This highly popular pedal has been around for many years and it is widely copied Several years ago I made up my own stomp box version of it Initially driven from a 9V battery then later from a 9V wallwart I pretty much slavishly copied the original s circuit Later still I modified the main gain stage and then added a hard clipping circuit the distortion mode I used this for many years with my SH 101 and SH 1 and it s pretty much the plaintive solo sound on my own music albums The Oakley Overdrive module uses very similar circuitry to this prototype pedal The basic circuit topology remained the same but I changed the design to allow it to run from a split power supply I was careful to recreate the same voltage limits as in the 9V design as I was keen to replicate the op amp s saturated output characteristics I also tailored the gain stages to be more responsive to the
13. ke the equivalent of the TB 303 in the guitar world and the original green units sell for a great deal of money However the basic circuit is actually quite simple and it is one that I have used in various home made pedals for some time There are great deal of DIY TS 808 clones out there and many of them will talk about the huge differences in using different diodes and types op amps I found that for synthesiser use at least the actual sonic differences due to the actual devices used are not quite as obvious as internet lore has decreed However I will leave it to the builder to experiment here and I am sure that the Oakley Sound Forum would be a great place to discuss your findings The key in the basic TS overdrive circuit is the usage of a standard non inverting high gain op amp stage U3A with two diodes in reverse parallel with the resistative feedback path These diodes act to limit the voltage across the feedback resistor These are shown in the schematic as D1 and D2 They can be switched in and out of the circuit with SW2 the overdrive and distortion selection switch Because they act upon the feedback voltage and not the output signal directly they do not behave as a traditional clipping circuit In the latter any 10 signal is simply limited to a set maximum or minimum voltage The TS circuit is more subtle than that The gain of the op amp non inverting amplifier is set by the resistances within the feedback loop but because of
14. lder to experiment here but I did like the results when using the OP275G in both U1 and U2 Use a socket for U1 and you can swap chip types with ease The diodes are just ordinary 1N4148 silicon diodes However there is some scope in playing around with the diode types in positions D1 and D2 and positions D3 and 4 Indeed some useful results can be obtained in using germanium diodes like the OA91 or 1N34A in positions D1 and D3 This makes for asymmetrical distortion but I have not found the results to be especially different in synthesiser use You could also use two diodes in series for one of the places eg D1 could be replaced by one 1N4148 and a 1N34 lt A in series U3 and U4 are three terminal regulators They are listed as 100mA devices and are 5V and 5V respectively They are very common devices but be careful you don t get the surface mount versions You need the plastic TO 92 ones and not the SOP 8 package You will also need a PC mount horizontal double pole double throw switch These are sometimes called DPDT or 2PCO two pole changeover This type of switch has two sets of contacts inside each one has a wiper that can move between two other contacts These sorts of switches have six solder tags Watch out for sizes there are many different types of toggle switches The ones I recommend are Multicomp s part 1MD1T2B4M6RE which is available from Farnell as part number 947 3270 Alternatively Rapid sell a plastic bezelled one t
15. levels seen in a modular synthesiser The key thing about using this module is to not use any signal that has a high harmonic content Indeed inserting a raw square wave into it will do nothing Overdriving a square wave simply produces another square wave The tone control may have an effect but it probably won t lead to an increase in distortion Inserting a sawtooth will also have little effect In fact it is more likely in this case that the sound is dulled the sawtooth waveform would be turned into something more square wave like and therefore less harmonics would result None of these things are perhaps what we would look for in a distortion unit Therefore to get the best out of the unit when playing just single notes at one time it is important that the input signal should have a relatively low number of harmonics Where the Overdrive shines is when you use the module after a filter especially one set to relatively high resonance The filter will select certain harmonics and the overdrive module will accentuate these still further So much so that the harmonic s frequency will dominate over the fundamental The effect is similar to the classic Moog Prodigy sync sound when sweeping the frequency of a slaved VCO And overdriving a simple one VCO one VCF arrangement is used frequently with the TB303 to give those rasping squealing acid lines However it can be also used more subtly on more mellow filter sweeps with the overdrive addin
16. ns of the lugs of the sockets that go directly to the PCB are summarised in the table below Socket Name Tag type Header SKT Pin number INPUT Signal 1 the square one INPUT Earth 2 OUTPUT Signal 3 OUTPUT Earth 4 Once that is done your module is ready for testing 14 Testing testing 1 2 3 Apply power to the unit making sure you are applying the power correctly Check that no device is running hot Any sign of smoke or strange smells turn off the power immediately and recheck the polarity of the power supply and the direction of the ICs in their sockets and the polarity of the electrolytic capacitors Assuming everything is OK so far it is time to apply an audio input The easiest way to test the Overdrive module is to use a triangle wave output from a VCO Start with the TIMBRE pot set to its middle position the gain pot at its lowest and the BALANCE pot to DRY Set the switch to OVERDRIVE If you listen to the output signal you should hear just the triangle wave as it would be if it were coming straight out of the VCO Be careful to check your listening levels as the output signal will get louder in the next section Now rotate the BALANCE pot and you should hear the sound becoming brighter Now turn up the GAIN and listen as the sound gets both louder and brighter still Change the switch to DISTORTION and the sound gets louder still and more harsh There will a small click in the audio output as the switch is moved this i
17. rol that affects the frequency response of the effected output The mix out or balance pot is essentially a wet dry mix control that allows you to add only as much of the effect as you want Voltage control is determined not within this unit but as part of the signal chain placed before this module Using a VCA to control the signal level that is fed into this unit will determine the strength of the overdrive or distortion Using a VCF to alter the timbre of the signal fed to this module will control the overall harmonic level far more than using a filter alone In fact hard sync type sounds can be easily obtained by simply sweeping the filter s cut off frequency The Oakley Overdrive module for the Eurorack format This module has been built by Krisp1 Using the Oakley Overdrive A Personal Perspective Since this module has been available I have read many comments from users regarding its usefulness Probably more than any other Oakley module it has produced the largest split of people who either loved and still love it and those that were profoundly disappointed with it Truthfully I can t say I particularly enjoy receiving negative comments but in some ways it is those negative comments that make one work harder to perfect any design The problem is that with some things it simply boils down to personal taste I think the Oakley Overdrive is one such thing it either produces a sound that you like or it doesn t Furthermore since
18. s normal behaviour Check that the GAIN pot still has an effect on the sound with the switch in this position Alter the TIMBRE pot and you ll hear that this acts as a simple tone control boosting treble signals at its maximum level You ll probably also notice that with a high gain setting that the volume increases quite dramatically too as considerably more of the higher harmonics are let through If all this happens the chances are that you have a working module 15 Final Comments If you have any problems with the module an excellent source of support is the Oakley Sound Forum at Muffwiggler com Paul Darlow and I are on this group as well as many other users and builders of Oakley modules If you can t get your project to work then Oakley Sound Systems are able to offer a get you working service If you wish to take up this service please e mail me Tony Allgood at my contact e mail address found on the website I can service either fully populated PCBs or whole modules You will be charged for all postage costs any parts used and my time at 25GBP per hour Most faults can be found and fixed within one hour and I normally return modules within a week The minimum charge is 25GBP plus return postage costs If you have a comment about this user guide or have a found a mistake in it then please do let me know But please do not contact me or Paul Darlow directly with questions about sourcing components or general fault fin
19. the way it works this is always more than or equal to one ie 0dB That is the output level is never less than the input The exception to this is at very high frequencies when the op amp reaches its operating limits Ignoring the diodes for now U1A has its passband gain set to a minimum of 11 via R2 and R1 The gain pot allows this gain to increase still further by increasing the feedback resistance With the gain pot turned up full the maximum passband gain of the op amp without the diodes is 111 A diode will behave in such a way as to limit the positive voltage across it to no more than 0 6V It does this by effectively changing its resistance depending on the voltage it has across it Two diodes connected in reverse parallel head to tail tail to head will seek to limit the voltage across them to 0 6V D1 and D2 are connected to act like this So as the output level of U1A rises either by turning up the gain pot or by applying a bigger input signal so does the feedback voltage Once the feedback voltage gets to beyond 0 6V or below 0 6V the diodes start to conduct and the rise in output level is tempered However the gain of UIA cannot fall to below unity so the diodes only appear to act on the amplified signal Thus what we get at the output is a clipped amplified signal plus the original signal superimposed on it This is the TS sound and it has great tonal characteristics I ought to add that a great part of the overdrive sound is
Download Pdf Manuals
Related Search