Centurian User Manual.indd
Contents
1. SOLID LINK TO MOTOR F2 SOLID LINK TO MOTOR F1 GROUND RED lt z O gt AY Y SERIES WOUND MOTOR FOR PAIRING SOLENOID BLOCK i WHITE USED a RED x o i 1 om z lt fe ca z m z RECEIVER YELLOW ee CS i a wos www warriorwinch co uk WINCHES woe WWw warriorwinch co uk WINCHES TROUBLESHOOTING RADIO REMOTE CONTROL PROBLEM POSSIBLE CAUSES SOLUTION GREEN LED light does not Fiat Batteries Replace the remote control batteries See shine when key is pressed Replacing the batteries in the Transmitter System does not resoond Incorrect replacement Check that the batteries have been to the controls of batteries inserted correctly System not coded Re code the system See System Coding RECEIVER UNIT PROBLEM POSSIBLE CAUSES SOLUTION These devices complies with Part 15 of the FCC rules Check the emergency mushroom button Absence of power in on the transmitter is in the release position the receiver unit Check the vehicle battery is correctly connected to the receiver unit System does not respond Incorrect connection of Check the cabling to the users indicators to the controls the cabling to utilities electro valves etc Incorrect installation of The receiver must not be shielded by ferrous the receiver masses see Positioning the receiver unit System not coded Re code the system2. ENTURION RADIO REMOTE CONTROL USER AND MAINTENANCE MANUAL WARNINGS This manual is an essential part of the device and it should be thoroughly kept for later consultation Carefully read the warnings contained in this manual concerning safety and a proper preservation of the product These warnings are ALWAYS to be carefully read before using the device Winch Solutions Ltd declines all responsibility for any trouble arising from the non compliance with these warnings Avoid attempting to repair the device by yourself Repairs performed by unskilled people can cause serious damages or failures For assistance apply to your local authorized service centre Use only original spare parts Always keep at a safe distance from the moving parts Keep the radio control out of the children s reach was WwWww warriorwinch co uk WINCHES TECHNICAL FEATURES Number of command 2 e 2 LED indicator lights Frequency bands ISM 868 915 MHz e Silicon rubber keypad grade of enclosure IP67 Power supply N 2 AAA 1 5 batteries e Operating temperature 20 C to 70 C Absorption at rest 1 uA e Dimension in mm 109 x 56 x 30 Average absorption in transmission 14 mA e Weight with batteries 120 g Maximum range in an open field 100 150 m in open field and free interference environment INSTRUCTIONS FOR USE For correct use and in order to avoid damage to people or things it is obligatory to follow these instruc
3. current for each channel 5 A Microprocessor electronics control e Maximum total suppliable current 7 A Dimensions 190 x 83 x 22 with antenna e Receiver category EN 300 220 1 2 Grade of enclosure IP67 e Protection of battery inversion polarity 12 24 VDC 10 30 allowed rating power supply through connection to the vehicle s battery Typical quiescent current 18 mA a 12 V 14mAa 24 V SYSTEM CODING It is necessary to code the system only if you have to replace the transmitter unit or if you want to use it with a different receiver from the one it was purchased with Follow the instructions to code the system 1 Take the power supply off the receiver 2 Disconnect the white or gray cable from negative pole of the battery and connect it to the positive pole of the battery 3 Put power into the receiver The led on the receiver start to blink 4 Press any 3 keys at the same time on the radio control transmitter within 15 seconds since it has been switched on also more times if it is necessary 5 At this point the coding occurred The led on the receiver turn off 6 Take the power supply off the receiver 7 Disconnect the white or gray cable from positive pole of the battery and connect it to the negative pole of the battery 8 Put power into the receiver with the connector inserted to verify correct operation press key START on the transmitter and abilitate the outputs INSTRUCTIONS FOR WIRING CONNECTION 7
4. see System Coding PRODUCT IDENTIFYING LABELS Til ruta a EE T E EEE Bimsim e mai IRTI ra Bita i Fa gt 000000 Cd si m Cod nnOJOPNX SIS nn000 ee u lal igs e hd FCC ID Os IRTXEASY Product serial number Wide 201 5 site AAA _ Us i nnnnn Product model a S N Product serial number Cod Product identification code INTERNAL LABEL EXTERNAL LABEL EXTERNAL LABEL ON TRANSMITTER CE MARK a This product may be subjected to usage restriction FCC STATEMENTS STATICA A Pisaba aby URTE Operation is subject to the following two conditions x 1520 EMH These devices may not cause harmful interference and EASY sm 000000 These devices must accept any interference received including interference that may Cod nNOQOPNY S1 nnddd cause undesired operation FCC ID OSIRTXEASY NOTE The manufacturer is not responsible for any radio or TV interference caused by dde 2x15 site AAA unauthorized modifications to these equipment Such modifications could void the user s authority to operate the equipment NIMBLERTX label example FCC ID O8Innnnnnn wae Wwww warriorwinch co uk _ WINCHES
5. HE INSTRUCTIONS FOR REPLACING THE BATTERIES HANDLING THINGS DELICATELY IN A CLEAN AREA IT IS NOT ADVISABLE TO USE CARBON ZINC BATTERIES AS THEY CAN UNDERGO SELF DISCHARGE MORE RAPIDLY THAN ALKALINE ONES DO NOT USE RECHARGEABLE BATTERIES r mAr Wwww warriorwinch co uk wae WWwWWw warriorwinch co uk wW WINCHES Grn TURION RADIO REMOTE CONTROL 2 COMMAND USER AND MAINTENANCE MANUAL WARNINGS This manual is an essential part of the device and it should be thoroughly kept for later consultation Carefully read the warnings contained in this manual concerning safety and a proper preservation of the product These warnings are ALWAYS to be carefully read before using the device Winch Solutions Ltd declines all responsibility for any trouble arising from the non compliance with these warnings Do not travel with the device switched on e Connect the system only to the vehicle s battery e Before carrying out any mechanical maintenance operation welding on the vehicle disconnect the battery clips e Avoid attempting to repair the device by yourself Repairs performed by unskilled people can cause serious damages or failures For assistance apply to your local authorized service centre e Use only original spare parts e Always keep at a safe distance from the moving parts TECHNICAL FEATURES Number of outputs 2 e Integral resettable fuse 7 A Frequency bands ISM 868 915 MHz e Maximum suppliable
6. WIRE CONNECTION FUNCTION 5 WIRE CONNECTION FUNCTION Green OUT 1 white orno Rea amenn NOTE It is necessary to connect the white cable with the black cable to the negative pole of the battery white waster Ouipar rink Emergency oiou Alimentation NOTE It is necessary to connect the grey cable with the black cable to the negative pole of the battery To operate from the transmitter consult the user manual of the transmitter coupled with the receiver yon WWw warriorwinch co uk WINCHES wae Www warriorwinch co uk POSITIONING OF THE RECEIVER UNIT DIMENSION AND DRILLING TEMPLATE For a proper functioning locate the receiver tyoe CENTURION with the cable output downwards as shown in the picture below The receiver is provided with an integrated antenna be sure to locate it at sight not inside any metal box or screened by ferrous masses ex protection carter For the receiver installation use supplied fixing screw or equivalent POSITIONING OF THE RECEIVER NIMBLE CORRECT WRONG PLACEMENT DIMENSION DRILLING TEMPLATE NIMBLE 70 5 NP 26mm DIMENSION BOX RECEIVER NIMBLE ae The system is automatically protected from power overload and from possible short circuit on corresponding outputs by an internal resettable fuse 7A Ee REMOTE TO CONTACTOR BLOCK WIRING ENCLOSED SOLENOID WIRING AGOS YOLOW HONIMOL BATTERY SOLID LINK TO MOTOR A
7. rance Meaning Flash every 3 sec Key always pressed The warning alarms only show Flash every 1 sec Absence of link radio when a key is pressed If no keys are pressed the LEDs stay off Flash twice every 1 sec Loss of link radio Flash every 1 sec Flat batteries lt 2 5V REPLACING THE BATTERIES IN THE TRANSMITTER If the red LED on the handset flashes when the key is held down it means that the batteries are almost flat lt 2 5 V In this situation replace the batteries as soon as possible since the system performance may be impaired When the voltage reaches values lower than 2 2 V the red LED stays on when the key is pressed In this situation replace the batteries as it is not possible to give commands to the output ports To replace the batteries follow these instructions Obtain 2 AAA 1 5V alkaline batteries Open the battery compartment by unscrewing the two screws figure 1 Remove the flat batteries from their holder figure 2 Insert the new batteries paying attention to the polarity shown on the end Before going ahead with closing the battery compartment made sure the green LED emits a flash each time a key is pressed 5 After checking that the transmitter is working properly close the container and screw back on the two screws indicated at point 2 m a Figure 1 Figure 2 THE REMOTE CONTROL CONTAINS MINIATURIZED ELECTRONIC CIRCUITRY AND SO WE RECOMMEND TAKING GREAT CARE WHEN FOLLOWING T
8. tions 1 Power up the receiver and wait a few seconds the receiver takes a couple of seconds to be able to operate as it carries out a self diagnosis 2 Press START to allow the system to receive the transmission the system will stay active for 2 minutes after the last control has been given after which it resets Then press START again to restart the system 3 Press the required key on the transmitter to activate the related output on the receiver t 4 IN OUT 4 Press the STOP key to inhibit the controls reception In this phase all the controls are reset To activate the system again press START LED INDICATOR ON THE TRANSMITTER REGULAR FUNCTIONING GREEN LED During standard operation of the transmitter the GREEN led flashes when any key is pressed Holding down any key will result in the GREEN led flashing every 3 seconds LOW BATTERY RED LED When the battery is low 2 5V the RED led will flash whilst any key is pressed At this point we suggest you replace the battery If the voltage reaches 2 2V the RED led will stay on whilst any key is pressed NB DO NOT LEAVE FLAT BATTERIES INSIDE THE TRANSMITTER SYSTEM CODING Coding system is an operation that is only necessary when the receiver has to be replaced or you want to use it with a different radio remote control from the one it is coupled with at the time of purchase TO RECODE THE SYSTEM REFER TO THE RECEIVER USER MANUAL WARNING ALARM te Appea
Download Pdf Manuals
Related Search