User manual - Snooper Services
Contents
1. Alarm 1 a time T1 OFF or T1 ON Press and hold 11 Your SR200 will display HOLD SET and AL 1 will flash Press S1 or S11 to toggle through AL 1 to AL 5 then press S5 to select the alarm you want to set The HOUR digit will start to flash Press S1 or S11 to adjust the hour value then press S5 to confirm The minute value will now flash Press S1 or S11 to adjust the minute value then press S5 to confirm T1 or T2 will now flash Press S1 or S11 to select whether this alarm relates to T1 your time zone 1 or T2 your time zone 2 then press S5 to confirm Press S1 or S11 to change the setting Press S5 to confirm ON Alarm on or OFF Alarm off will now flash Press S1 or S11 to turn the alarm ON or OFF then press S5 to confirm Press S7 to return ALRM sub menu Press S7 again to exit and return to TIME mode How to preview alarms set and switch alarms and button chime beep on and off Press S7 and scroll through the modes until you see ALRM Press S5 to scroll through and preview AL 1 Alarm 1 to AL 5 Alarm 5 and then CHIME Press S1 to turn an alarm on or off then press S5 to confirm When CHIME is displayed press S1 to switch the CHIME on or off CHIME is the beep that is emitted when you press any of the buttons and can be switch on and off Press S7 to exit and return to TIME mode A small bell icon will be displayed to the left hand side of the screen in TIME mode to indicate that you h2. review all the lap times you recorded directly on your SR200 by pressing S5 before saving the session The lap times recorded can also be reviewed after you have saved them in DATA mode Using your SR200 indoors without a GPS signal It is possible to use your SR200 indoors where there is no GPS signal The functions CHRONO LAP and CLOCK will operate as normal but DISTANCE and SPEED will not as they cannot be calculated without GPS To use your SR200 indoors without a GPS signal follow these instructions From TIME mode press and hold S7 for approx 3 seconds Your SR200 will display GPS OFF and will then automatically change to CHRONO view but with INDOOR flashing at the top of the screen Your SR200 is now in INDOOR mode CHRONO LAP and CLOCK function can be used as normal but no DISTANCE or SPEED values will be displayed or recorded Follow the RUN mode instructions above for further details of how to operate CHRONO and to save and delete training sessions How to set UNITS metric or imperial You can set your SR200 to display speed and display and record distances in kilometres or miles When in RUN mode press and hold 11 Your SR200 will display HOLD SET and then SET and AUTO LAP will flash Use S1 to scroll through the different user settings until you see UNITS then press S5 to select Press S1 to switch between KM or MI kilometres or miles and press S5 to confirm your selection Press S7 to return to the last used
3. scroll through the settings and S5 to select SET UNIT Metric or Imperial This is shown as KM kilometres or MI miles but it also determines the units of measurement displayed for weight Ibs or kg and height feet and inches or cm SET USER Gender age weight height RUN mode sub views While training your SR200 can display different types of information depending on your requirements These can include distance pace speed calorie burn and time You can switch between these views by pressing S5 at any time during your training session You can also set your SR200 to display different combinations of information DISTANCE Displays and records how far you have run or walked PACE Displays your current pace Your SR200 will advise you that if you continue running at your current speed you will complete a mile or a km in x minutes This value moves up or down depending on your speed and can be viewed as you run SPEED Displays a straightforward view of your current speed in either mph or kmh CALORIE Displays the number of calories you are burning per hour SNOOPER 4 UK TIME Displays the time Setting RUN mode sub views You can set your SR200 to display different combinations of information over 3 lines at the same time Chronograph will always be displayed on line 1 but you can you change the data displayed on both lines 2 and 3 For example you can set your SR200 to display CHRONO PACE a
4. seconds each time you press the light button 11 and press S5 to confirm your selection Press S7 to return to the NIGHT mode sub menu Press S7 again to exit and return to TIME mode How to set and use NIGHT mode NIGHT mode enables you to set the backlight to come on automatically after you launch one of the training modes such as RUN or CHRONO within a pre set time period For example say you set the NIGHT mode time period to start at 69m and end at 11pm if you launched RUN or HRM mode within that time period the backlight would automatically come on and stay on for as long as your SR200 remained in that mode The backlight will automatically illuminate your RUN or HRM data for the duration of your training session Press S7 and scroll through the modes until you see TIME Press and hold 11 The screen will display HOLD SET and then TIME will flash Press S1 or S11 until you see NIGHT flashing on the screen then press S5 to enter Press S1 or S11 until the screen displays NIGHT ON then press S5 to enter The display will show TIME START followed by a time with the hour value flashing Adjust the start time to your preferred setting starting with the hour value Press S1 or S11 to select your setting then press S5 to confirm The minute value will now flash Press S1 or S11 to adjust the minute value to your preferred setting then press S5 to save The display will show TIME START again Press S1 or S11 to switch
5. 11 then press S5 to enter Set the MINUTE by pressing S1 or S11 then press S5 to enter Set the SECOND by pressing S1 or S11 then press S5 to enter SNOOPER 8 UK Set the YEAR by pressing S1 or S11 then press S5 to enter Set the MONTH by pressing S1 or S11 then press S5 to enter Set the DATE by pressing S1 or S11 then press S5 to enter Set the 12 24H by pressing S1 or S11 then press S5 to enter Press S5 to enter and go back to T1 T2 setting screen Press S7 to go back to TIME setting sub menu and press S7 again to return to TIME mode Backlight and NIGHT settings NIGHT setting allows you to control how long the backlight comes on when you press the light button S11 in TIME mode NIGHT setting also enables you to set up and use NIGHT mode How to set and use the backlight Your SR200 has a backlight so you can illuminate the screen to view the time if it s dark The backlight is activated by pressing the light button S11 You can set the backlight to come on for either 10 seconds or 20 seconds by following these instructions Press S7 and scroll through the modes until you see TIME Press and hold 11 The screen will display HOLD SET then TIME will flash Press S1 until you see NIGHT flashing on the screen then press S5 to enter 10 SECONDS or 20 SECONDS will be displayed on the screen Press S1 or S11 to select whether you would like the backlight to come on for 10 seconds or 20
6. M RUN mode functions How to enter and set up RUN mode Press S7 to scroll through the main modes to RUN mode If you are in TIME mode and want to go directly to RUN mode you can press S1 When you get to RUN after about 2 seconds the screen changes and displays SEARCH and your SR200 will start searching for satellites automatically Once your SR200 has a GPS connection it will then display the battery level remaining memory and then the GPS GO screen indicating it is ready for use Note If there is no GPS signal it will display the INDOOR screen Using RUN mode To begin your training session press 1 The chronograph will automatically start to time your session As you begin to run or walk you will be able to switch views by pressing S5 to observe your current pace the distance you have travelled and your current calorie burn To stop your training session press S1 To save the information collected during your training session press and hold S1 for approx 3 secs Your SR200 will display HOLD RESET and then SAVE plus the number of the session User settings To enter and set your RUN mode user settings enter RUN mode and press and hold 11 Your SR200 will display HOLD SET and then SET and AUTO LAP Press S1 to scroll between the following user selectable settings and press S5 to enter AUTO LAP Off 0 4 miles 1 0 mile 2 0 miles 3 0 miles 4 0 miles 5 0 miles Alert On or Off Press S1 to
7. ORUN SR200 GPS SPORTS WATCH Keeping you one step ahead x User manual SNOOPER SR200 GPS SPORTS WATCH Congratulations on purchasing your Snooper RUN SR200 Your new Snooper RUN SR200 is packed with loads of great features It uses the latest micro GPS technology and Snooper s comprehensive RUN software to provide you with all the features and functions you would expect to find on one of the most advanced training watches on the market First charge the battery Before you use your SR200 you must charge the lithium battery for at least 4 hours using the USB charging clip cable Ongoing charging times will depend on usage Recharge whenever the display indicates a low battery Warning You must recharge every 1 2 months even if your SR200 is not being used While the battery is charging your SR200 cannot be used and all buttons are disabled When the battery is full the display will read CHARGE 100 The battery life is 8 hours when you are using a function that needs GPS such as RUN If GPS is off say in TIME mode the battery will last up to 12 months Charging your battery step by step 1 Plug your SR200 into your PC with the USB charging clip cable provided 2 Align the charging clip with the contact pins on the back of your SR200 3 Connect the charging clip securely to your SR200 Your SR200 will display CHARGE and the percentage charge level of the battery Battery low condition Y
8. ase note your SR200 should never be used while swimming SNOOPER 11 UK Service under warranty Your Snooper RUN SR200 comes with a standard one year manufacturer s warranty To register for warranty purposes please visit www snooperneo co uk registration If for some reason your unit requires service under warranty return your Snooper RUN SR200 via special delivery insured and in suitable packaging to The Returns Department Performance Products Limited Cleaver House Sarus Court Manor Park Cheshire WA7 1UL Please enclose the following information Your name address and a full description of the problem A telephone number where you can be reached during business hours Your SR200 serial number Disposal of old electrical amp electronic equipment applicable in the European Union This symbol on a product or its packaging indicates that the product should not be treated as household waste It should be handed over to an appropriate collection point for the recycling of electrical equipment By ensuring that this product is disposed of correctly you will help prevent potential negative impact on the environment The recycling of materials will help to conserve natural resources For further details about recycling please contact your local authority or the shop where it was originally purchased Information on GPS Global Positioning System GPS is a satellite system made up of a network of 24 or
9. ave an active alarm set SR200 troubleshooting guide PROBLEM QUESTION cannot get a GPS signal Can reset my SR200 Will my data and personal settings be lost after reset my SR200 The battery indicator does not seem to be accurate SOLUTION ANSWER Take your SR200 outdoors and away from tress and tall buildings Remain stationary and try getting GPS signal again Be sure that the antenna is pointing towards the sky for better signal reception You can reset your SR200 by pressing S1 S5 S7 and S11 together The date and time will be reset to default values You can set it again manually or automatically through GPS Your data and personal settings are saved in the flash memory and will not be lost after you reset Allow your SR200 to fully discharge then fully charge it without interruption We recommend a regular recharge every 1 2 months to maintain good battery condition even if your SR200 is not used Caring for your SR200 Clean with a dampened cloth preferably with mild detergent solution Wipe dry using a dry cloth Do not use chemical cleaners and solvents that may damage plastic components Prolonged extreme temperatures may result in permanent damage Your SR200 can resist water pressure down to 30 metres After submersion wipe dry then air dry before using or charging Caution Prolonged water submersion may cause electronic shorting which may cause minor skin burns or irritation Ple
10. de Your SR200 will momentarily display DATA then the latest data file saved If there is no data available it will display DATA If you want to view the data from other saved training sessions press S1 to scroll through the data files previously saved Note A maximum of 30 files with 100 laps in each file can be saved Next press S5 to enter the selected file Your SR200 will display the start time end time and distance Press S1 or S5 to scroll forwards through the data saved for each session You will be able to view the following information Start end time amp distance Chrono calorie amp distance Chrono max pace amp ave pace Chrono max speed amp ave speed Lap 1 time amp distance Lap 2 time amp distance SNOOPER 9 UK last lap time distance VIEW DELETE DEL ALL sub menus Press S7 to exit How to use the VIEW DELETE DEL ALL sub menus VIEW Press S5 while VIEW is highlighted to view the session data again Your SR200 will go back to the start end time distance screen Press S7 to exit DELETE Press S1 to highlight DELETE and press S5 to select After 2 seconds the file will automatically be deleted and your SR200 will go back to DATA mode Press S7 to exit DEL ALL Use S1 to highlight DEL ALL and press S5 to select Your SR200 will display DATA Press S7 to exit DATA numbering system of saved RUN data Sample data n
11. gth of lap you require press S1 to switch between 0 4 1 2 3 4 5 kilometres or miles depending on the units you have selected in user settings Then press S5 to select Once you have selected the lap distance press S5 to confirm ALERT ON will be displayed Press S1 to switch between ALERT ON and ALERT OFF and press S5 to confirm When training your SR200 will beep once each time you reach your selected lap distance assuming you have the alert switched on Press S7 to go back to the user settings menu Using the manual lap time function The lap function lets you take and save a lap time at any point during your session If you are running on a track for instance you can time how long it takes to complete each lap Your SR200 will display the time of the lap as you complete each lap but you can also review your lap times later directly on your SR200 The manual lap time function can be accessed from the CHRONO mode You can access CHRONO and use the manual lap time in two different ways Launch RUN mode press S1 to start your training session as normal and press S7 to switch to CHRONO Or go directly to CHRONO by pressing S7 until CHRONO is displayed on the screen Once you are in CHRONO and when you are ready to record and save a lap time simply press S5 Your last lap time will be displayed briefly on your SR200 then the display will revert to the previous data view selected Once you have completed your training session you can
12. mode i e RUN TIME etc How to set USER gender age weight and height To enable your SR200 to accurately calculate calorie burn you will need to tell your SR200 whether you are male or female your age weight and height When in RUN mode press and hold 11 Your SR200 will display HOLD SET and then SET and AUTO LAP will flash Use S1 to scroll through the user settings until you see USER then press S5 to select MALE or FEMALE will start to flash Press S1 to switch between MALE or FEMALE then press S5 to confirm Next AGE will be displayed Use S1 to adjust your age then press S5 to confirm Next WEIGHT will be displayed Use S1 to adjust your weight then press S5 to confirm Next HEIGHT will be displayed Use S1 to adjust your height then press S5 to confirm Press S7 to return to the last used mode i e RUN TIME etc TIME mode functions How to enter the TIME mode To enter the TIME mode and use your SR200 as a normal watch press S7 and scroll through the modes until you see TIME In TIME mode your SR200 will automatically display the Time Zone ie LON London the day date and the time TIME mode settings The time on your SR200 will be set correctly when manufactured so it will work out of the box If you want to set the time yourself the procedure is explained below How to set the time From TIME mode you can set two different TIME zones From TIME mode press and hold S11 The display
13. more satellites GPS works best in clear weather conditions anywhere in the world 24 hours a day When 3 satellite signals are received your SR200 will have 2D GPS fixed latitude and longitude When 4 or more satellite signals are received your SR200 will have 3D GPS fixed 12 e UK
14. nd CALORIE burn at the same time or CHRONO CALORIE burn and CLOCK at the same time Changing data displayed on lines 2 and 3 You can select which two pieces of data you want displayed on your SR200 at any time during a training session You do this by using the S3 button in two different ways Launch RUN mode in the normal way and press S1 to start your training session Press S5 briefly to change the data type displayed on line 3 Keep pressing S5 to choose between SPEED CALORIE CLOCK CHRONO DISTANCE or PACE Each time you press S5 the data type displayed will appear briefly to confirm your selection To change the data type displayed on line 2 press and hold S5 until the data type changes Keep pressing and holding S5 to choose between SPEED CALORIE CLOCK CHRONO DISTANCE or PACE You can change the data displayed on either line at any time during your training session How to view your RUN data When you have finished a training session press S1 to stop The chronograph will stop your SR200 will stop recording data and STOP will flash on the screen To immediately view the data collected during this session press S5 before saving The following information will be displayed Stop Chrono Distance Calorie Ave Pace Max Pace Calorie Ave Speed Max Speed To save this session press and hold S1 for approx 3 seconds How to enter and use DATA mode Press S7 to scroll through the main modes to DATA mo
15. ou cannot turn on GPS when the battery is low You will need to recharge the battery first before your SR200 can connect to GPS When battery level becomes very low your SR200 will automatically turn off and the screen will go blank In RUN mode if your SR200 automatically turns off because there is not sufficient power in the battery you will lose any information that was being collected during that session Previously stored and saved data will not be lost You only lose data that was being collected and that was not saved prior to the battery running out SNOOPER 2 UK Getting to know the buttons and modes Push button functions N S1 Start Stop Up S1 Wz AN Yim 3 S5 View Lap S7 Change Mode Exit ah D S11 Light Set Save NS A Your main SR200 modes Press S7 to scroll through the main modes of your SR200 TIME Allows you can set and view two time zones e g London and New York City See full details of how to set the time on page 15 RUN You can view the following functions PACE SPEED CAL CLOCK CHRONO DISTANCE CHRONO Chronograph DATA View statistics of training sessions saved ALARM Set up to five alarms a day SET Change watch and user settings Scrolling through modes shortcuts PRESS 7 TIME mode PRESSSSTOGOTORUN 44 RUN mode ALARM mode RUN DATA mode Press S7 to scroll through your SR200 main modes TIME RUN RUN DATA AND ALAR
16. to TIME END Press Slor S11 to adjust the hour value then press S5 to enter Press S1 or S11 to adjust the minute value then press S5 to enter Press S7 to return to the NIGHT mode sub menu Press S7 again to exit NIGHT mode and return to TIME mode How to adjust the LCD CONTRAST in TIME mode Press S7 and scroll through the modes until you see TIME Press and hold 11 The screen will display HOLD SET and then TIME will flash Press S1 or S11 until you see CONT then press S5 to enter The current contrast will be displayed Press S1 or S11 to adjust the contrast up or down between 10 and 100 then press S5 to save Press S7 to return to the CONT sub menu Press S7 again to exit and return to TIME mode CHIME Setting in TIME mode Chime refers to the beep that sounds when you press any of the buttons on your SR200 This feature can be turned on or off Press S7 and scroll through the modes until you see TIME Press and hold 11 The display will show HOLD SET and then TIME will flash Press S1 or S11 until you see CHIME then press S5 to enter Press S1 or S11 to select CHIME ON or CHIME OFF then press S5 to save Press S7 to return to the CHIME setting screen Press S7 again to exit and return to TIME mode How to set up and use the ALARM mode It is possible to set up to five different alarms on your SR200 Press S7 and scroll through the modes until you see ALRM The display will show AL 1
17. umber D 01 04G 0924 2 D Saved number of data file 04 Total number of files saved that day G Data recorded with GPS 09 Month 24 Day ofthe month Please note this total will include files saved and deleted Run Mode user settings and AUTO LAP setting To enter and set your RUN mode user settings press S7 to enter the RUN mode and then press and hold 11 Your SR200 will display HOLD SET and then SET and AUTO LAP will flash Press S1 to switch between the available settings and S5 to select a setting How to set AUTO LAP and use the manual lap time function Your SR200 incorporates an AUTO LAP feature within RUN mode that enables you to analyse your training session data split in to virtual laps The AUTO LAP feature can be switched on or off When AUTO LAP is switched on your SR200 will automatically alert you with an audible alarm each time you reach a pre specified distance You can set your SR200 to split your data over the following lap distances 0 4 miles or kilometres 1 mile or kilometre 2 miles or kilometres 3 miles or kilometres 4 miles or kilometres 5 miles or kilometres You will also be able to analyse the data recorded for each lap at the end of your session Setting the lap distance When in RUN mode press and hold 11 Your SR200 will display HOLD SET and then SET and AUTO LAP will flash Press S5 to select AUTO LAP and 1 KM will flash in the display To select the len
18. will show HOLD SET and then TIME will flash Press S5 to confirm T1 Time 1 will now be displayed If you want to set T1 press S5 If you want to set T2 press S1 to change T1 to T2 then press S5 to confirm The display will now show GPS and MANUAL Press S1 to switch between GPS or MANUAL then press S5 to confirm your selection Setting time with the GPS option Press S1 to select GPS When GPS is flashing press S5 to select Next press S1 or S11 to find the correct TIME ZONE for your location There are 106 city codes to choose from When you have found the correct location press S5 to confirm The display will now show DST Daylight Saving Time ON or DST OFF Press S1 to switch between DST ON and DST OFF then press S5 to confirm your selection The display will now show either 12H or 24H Press S1 to switch between the two then press S5 to confirm your selection The display will now show either D M Day Month or M D Month Day Press S1 to select how you want the Day and Month to be displayed on the watch and press S5 to confirm Press S7 to go back to the TIME setting sub menu and press S7 again to return to TIME mode The time will automatically be set next time your SR200 connects to GPS Your SR200 will connect to GPS when you launch RUN or CHRONO modes Setting time with the MANUAL option Press S1 to select MANUAL While MANUAL is flashing press S5 to enter Set the HOUR by pressing S1 or S
Download Pdf Manuals
Related Search