USER MANUAL
Contents
1. Blue eenen Jean 1G The earth has to be connected Lighting effects must not be connected to dimming packs OPERATION After you connected the effect to the mains the DMX MOVING HEAD SCANNER starts running During the Reset the motors are trimmed and the device is ready for use afterwards You can contro the Projectors individually via your DMx controller Every DMX channel has a different occupation with different features In order to call up the different fec ures you first have to open the shutter contro channel 5 DMX value 241 255 Turn the focus screw next to the objective iens for adjusting the focus in orcar to obtain a sharp projection Addressing Each projector occupies 6 channels To ensure that the control signals are pror rly directed to each projector the projector requires addressing This is to be done for Every ugle projector by changing the DIP switches as set out in this table The starting address is defined as the first channel from which the DMX I VING HEAD SCANNER will respond to the controller if you set for example the address tc lt nannel 7 the DMX MOVING HEAD SCANNER will use the channel 7 to 12 for control Please make sure that you don t have any overlapping channels in order to lt a ol each DMX MOVING HEAD SCANNER correctly and independently from any other on the DMX data link If two three or more DMX MOVING HEAD SCANNER is addressed similarly they will work2. amp is too far back in the reflector Push the lamp out by turning the screws A B C counterclockwise 1 4 turn at a time the light is bright and evenly distributed B oe Rigging DANGER TO LIFE Please consider the respective national norms during the installation The installation must only be carried out by an authorized dealer The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment This secondary Safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after c anges before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year E
3. MOVING HEAD SCANNER Overview D 1 projector head 2 objective iens nN 3 yoke 4 base 5 carrying handle 6 power switch 7 power supply 8 fuse holder 9 ventilation fan 10 DMX OUT socket 11 DMX IN socket o 6 D 8 12 Display 13 DIP switches 14 Function DIP switches 4 12 ENGLISH USER MANUAL DMX MOVING HEAD SCANNER INSTALLATION installing replacing the lamp DANGER TO LIFE Only install the tamp with the device switched off Unplug from mains before For the installation you need one HTI 150W OSRAM CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat The lamp life given by the manufacturer must never be exceeded This is why you need to take notes on the operational time of the lamp and replace the lamp in time Keep exchanged lamp in a protective container and Remove accordingly During the operation the lamp reaches temperatures of up to 600 C Before replacing the lamp unplug mains lead and let the lamp cool down approx 10 minutes During the installation do not touch the glass bulbs bare handed Please follow the lamp manufacturer s notes Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Procedure Step 1 Unscrew the fixation screws of the lamp co
4. be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any s of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material faii cables or sediments Further instructions depending on the installation spot amp to be adhered by a skilled installer and any safety problems have to be removes 12 e g porous usage have DANGER TO LIFE Disconnect from mains before starting maintenance operation CAUTION The lens has to be replaced when it is obviously damaged So that its function is impaired e g due to cracks or deep scratches The objective lens will require weekly cleaning as smoke fluid tends to bui up residues reducing the light output very quickly The cooling fans should be cleaned m lt The gobos may be cleaned with a soft brush The interior of the fixture should pe cleane cast annually using a vacuum cleaner or an air jet The dichroic color filters the gobo wheel and the internal lenses should be cw There are no serviceable parts inside the device except for the lam Maintenance and service operations are only to be carried out by authorizec ed monthly 11 12 ENGLISH USER MANUAL DMX MOVING HEAD SCANNER Please refer to the instructions under Iinsta
5. similarly 9 12 ENGLISH USER MANUAL DMX MOVING HEAD SCANNER Occupation of the DIP switches 8 bit mode Setting the DMX 1 2 3 74 5 76 7 J 9 Starting address ELE nS i I d aan Projector number DMx starting 1 2 4 18 16 32 6 gt 256 amp channels address 4 i l f On Device 1 channels 1 6 ror x a f x l On alaila I Device 2 channels 7 12 Of oT a On A ala oe Device 3 channels 13 18 Off j 7 7 aimee 7 s On ALA TA E Device 4 channels 19 24 OF ale r Device 5 ch 25 30 O a Jaa ee evice 5 channels 25 OF Sala 78 a Controlling After having addressed all DMX MOVING HEAD SCANNER you may now these via your lighting controller Note After switching on the DMX MOVING HEAD SCANNER will automatic DMX 512 data is received or not If the data is received the display wi A actually set address and the DMX LED is lit If there is no data received a DMX LED is off This situation can occur if The 3 PIN XLR plug cable with DMX signal from controller is not connec v the DMX MOVING HEAD SCANNER The controller is switched off or defective if the cable or connector is def zti wires are swap In the input connector DMX control channels Channel 1 7colors open white Channel 2 rotating gobos continuous rotation Channel 3 7gobos open white Channel 4 di
6. structure truss to which you are attaching the fixture is secure The moving head c n be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics see the drawing For overhead use always install a safety rope that can hold at least 12 times the weight c the fixture You must only use safety ropes with screw on carabines Pull the safety rope through th hole on the bottom of the base nd over the _ 83 trussing system etc insert the end ve in the carabine and tighten the fixation screws Use the safety rope exclusively as a closed ring Never use by only securing at each end The maximum drop distance must never exceed 20cm A safety rope which already hold the strain of a crash or which is defective mus not be used again DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert 1 12 ENGLISH USER MANUAL DMX MOVING HE SCANNER 1 Omega hoiders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick iock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder i DMX 512 connection connection between fixtures Projector 3 Projector 2 Projecto
7. NGLISH USER MANUAL DMX MOVING HEAD SCANNER Procedure The projector should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qu fications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector has to be installed out of the reach of people If the projector shall be lowered from the ceiling or high joists professional trussing systems have to be used The projector must never be fixed swinging freely in the room Caution Projectors may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the projector Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight DANGER OF FIRE When installing the device make sure there is no highly inflam nable material decoration articles etc within a distance of min 0 5m CAUTION Use 2 appropriate clamps to rig the fixture on the truss Follow the instructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the
8. Tonan ENGLISH USER MANUAL DMX MOVING HEAD SCANNER USER MANUAL DMX MOVING HEAD SCANNER CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initial start up Every person involved with the installation operation and maintenance of this device have to Be qualified Follow the instructions of this manual INTRODUCTION Thank you for having chosen a DMX MOVING HEAD SCANNER You will see you have acquired a powerful and versatile device Unpack your DMX MOVING HEAD SCANNER Before you initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual gas _ s Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to drastic temperature fluctuation e g
9. after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature This device falls under protection class The power plug must only be plugged into a protection class outlet g Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only z 1 12 ENGLISH USER MANUAL DMX MOVING HEAD SCANNER handle the power cord by the plug Never puli out the plug by tugging the power cord During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Caution During the operation the housing becomes very hot Danger of burning Never install the device on a highly flammable surfaces e g fair carpet HEALTH HAZARD Never look directly into the light source As sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs OPERATING DETERMINATIONS This device is a moving head spot for creating dec
10. jective liens or any housing cover is open as discharge lamps may explose and emit a high ultraviolet radiation which may cause burns The maximum ambient temperature t 45 C must never be exceeded Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety 2 12 ENGLISH USER MANUAL DMX MOVING HEAD SCANNER reasons Never remove the serial barcode from the device as this would make the guarantee void If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc DESCRIPTION OF THE DEVICE Features Powerful Moving Head Versatile Moving Head with a wide range of illumination and decoration possibilities 7 brilliant dichroic colors plus white 7 rotation metal gobos plus open Manual focus Strobe effect with 1 13 flashes per second Exact positioning within 360 Pan and 250 Tilt 6 DMX channels 3 DIGIT for starting address For bright 150 W discharge lamp Suitable controllers DMX Operator ENGLISH USER MANUAL DMX
11. lling Replacing the lamp Replacing the fuse ifthe lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Unscrew the fuse holder on the rear panel with a fitting s anticlockwise Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing and fix it Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged power supply cable available at your dealer Should you have further questions please contact your dealer TECHNICAL SPECIFICATIONS Power supply 230V 50HZ Power consumption 200W tb Mix control channels T6 DMX 512 connection 3 pin XLR Flash rate 13HZ Length 330mm L Width 335mm Height 360mm iita Net weight 12KGS Maximum ambient temperature 45 C Maximum housing temperature 90 C Min distance from flammable surfaces 0 5m T y T 7 SA Bene Min distance form lighted object 0 5m Fuse F5A 250V crewdriver from the housing it has to be replaced by a special Please note Every information is subject to change without prior notice 2003 7 3
12. mmer shutter and strobe Channel 5 Pan movement within 360 Channel 6 Tilt movement within 250 The DMX CHANNEL can be read directly off the 3 DIGIT display 10 12 viart operating tect whether A001 with AX input the h the input of 2 or the signal ENGLISH USER MANUAL DMX MOVING H7 4D SCANNER Special settings Mode Function DIP switch no 1 12 3 4 1 5 6 Not ied aes ddan ti Off g Ty v V Call i tel On lA all up colour separately lor v se z Set colour t iti an A et colour to every posl ion Off Vv Vv g g g j Set 16 bit mod On eI cs alae of jv iv V viv rt PAN t On la J Inve movemen rof g J 7 7 ij g J invert TILT t on Ioe nve movemen Off F 7 Vv Vv 7 Via the Function DIP switches you can adjust different modes and settings CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance The operator has to make sure that safety relating and machine technical installations are pected by a skilled person once a year The following points have to be considered during the inspection 4 All screws used for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not
13. orative effects This product is only allowed to be operated with an alternating current of 230 V 50 Hz and was designed for indoor use only This device is designed for professional use e g on stages in discotheques theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others The symbol m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than this value Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct fixation points only The safety rope must never be fixed at the transport handles Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the ob
14. r 1 Starting address 13 Starting address 7 Starting address 1 DNiX 512 ontroler The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work pre orly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order connect the controller with the fixture or one fixture with another Occupation of XLR connection DMX output DMX input XLR mounting socket XLR mounting plug 1 Ground 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal If you are using controllers with this occupation you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain you wish to connect DMX controliers with other XLR outputs you need to use adapter cable g 8 12 ENGLISH USER MANUAL DMX MOVING HEAD SCANNER Building a serial DMX chain Connect the DMxX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one Output with the input of the next fixture until a l fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a term tor Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug an slug it in the DMX output of the last fixture Connection with the mains Connect the device to the mains with the enclosed power Supply cable The occupation of the connection cables is as follows
15. ver and remove it Step 2 Unscrew the knurled head screws of the lamp holder and remove it Step 3 f replacing the lamp remove the old lamp from the lamp holder Step 4 insert the lamp into the lamp holder Step 5 Replace the lamp holder and tighten the knurled head screws Step 6 Adjust the lamp as described under lamp adjustment Step 7 Replace the lamp cover and tighten the fixation screws ENGLISH USER MANUAL DMX MOVING HEAD SCANNER Do not operate this device with opened cover Lamp adjustment The lamp holder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp open the shutter and the iris set the dimmer intensity onto 100 and focus the light on flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws A B C Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hop spot adjust the lamp until the light is even A To reduce a hot spot pull the lamp in by turning all three screws A B C clockwise 1 4 turn at a time until the light is evenly distributed CAUTION HOT LAMP Let the lamp cool down for10 iig min Change the lamp byloosening screws X and Y Adjust the lamp position byturning screws A B and If the light is brighter around the edze than it is in the center or if light output is low the
Download Pdf Manuals
Related Search