Söll GlideLoc Exit Section Aluminium Ladder
Contents
1. and use of systems and products against falls from height Prior to during every ascent ensure the function and conformity to regulations of all exit section elements The stop bolt Fig 7 2 0 on the rear side of the exit section has to independently snap back into the locking bore hole in the swivel part Fig 7 1 0 thus preventing the opening ofthe exit section Ensure that the guide rail is free from any dirt All bolt connections must be securely fastened and secured against loosening see section E Prior to and during each usage the exit section is to be checked with regard to function in accordance with the check list in Section I Maintenance If required the exit section can be cleaned using warm water and a hand brush After was hing dry with a clean cloth Do not use fat or oil dissolving quick cleaning dilution or cold cleaners If needed oil the stop bolt Fig 7 2 0 and the swivel part Fig 7 1 0 Safety At Height Limited 1 1 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER soll by Honeywell Further Remarks Safety At Height Limited 1 2 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT s by Honeywell Check list for the inspection and approval of Soll GlideLoc fall arrest systems Part No 10550 The check list on pages 13 14 must be fu2. authorized by the same refuse to accept product liability Full liability will therefore rest with the operator The check list see Section must be fully and correctly compiled by the chief engineer of the installing company by means of an indelible pen Before and during the use of the installed exit section the system must be visibly inspected to ensure that itis in safe operating condition The system has been tested and approved by Stelle 0158 EXAM BBG Pruf und Zertifizier GmbH Zertifizierungsstelle Dinnendahlstrake 9 44809 Bochum Safety At Height Limited 3 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk B 1 B 2 B 3 B 4 B 5 B 6 B 7 SAFETY MILLER s l by Honeywell Preparing for the installation of the exit device The assembly kit consists of 1 swivel part with integrated base plate and bolts 1 sawing gauge Equipment required for easy fitting 1 hack saw 1 flat file for removing burrs 1 ring endspanner size 19 mm 2 open spanners size 19mm At least one separate additional safety rope in accordance with EN 355 with fitted energy absorber to provide additional protection against falls from a height during the assembly of the equipment Personnel required for assembly At least two persons the second person is for the purpose of providing help and possible rescue to the fitter Components must be handled careful
3. SAFET Y MILLER Manual for the Installation Use and Maintenance Soll GlideLoc fall arrest system Exit Section Aluminium Part No 10550 In accordance with EN 353 Part 1 Serial Number in conjunction with Soll Aluminium Ladders Date 26 08 2008 SE 8 a Safety At Height Limited 1 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk A MILLER si by Honeywel Table of contents A General 3 B Preparing for the installation of the exit device A C Installation of the exit section 6 D Inspection and acceptance 9 E Bolt connections securing of bolts 9 F Directions for use of the exit section 10 G Maintenance of the exit section 11 H Maintenance 11 Check list 13 Tel 44 0 161 446 5615 These instructions are protected by copyright They may not be reproduced and distributed in any ways by any means without prior written consent of the author according to Articles 16 and 17 of the German Copyright Act Sperian Fall Protection Deutschland GmbH amp Co KG will prosecute any violations against this under Article 106 of the German Copyright Act Safety At Height Limited 2 Unit 1 Pennine View Marple Stockport Cheshire SK67JW www safety height co uk SAFETY MILLER A 3 A 4 A5 A6 A7 A8 A9 A 10 A 11 s by Honeywell General Anyone working with or on S LL exit section in accordance with EN 353 part 1 must be familia
4. d around the centre rail of the ladder gt The use of an external anchorage point We SSS EN 354 355 EN 358 Warning Never use the side stringer of a twin ladder for anchorage purposes Safety At Height Limited 5 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk C1 C2 SAFETY MILLER sO by Honeywell Installation of the exit section The exit section is principally installed between two rungs of the ladder Fig 2 The recommended height for installations is approximately 1 000 mm above the upper edge ofthe platform Fig 2 a ese SI I 440 W0 mm 20 i Safety At Height Limited 6 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT sO by Honeywell Fig 3a b Bolt the cutting template to the guide rail Fig 4 Cut out the segment of guide rail Fig 4 Safety At Height Limited 7 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER sO by Honeywell Fig 5 When fitting the exit section always make sure that the blocking device 1 1 is on the left hand side when viewed from the front of the ladder Fig 9 Fig 6 From the rear fit the exit section to the guide rail with the wording TOP pointing upwards and bolt in accordance with the diagram The Tuf
5. lly and correctly completed by the chief engineer of the assembling company using an indelible pen He is responsible for the correct nature of all information provided Check points which reveal defects or variations are to be entered in the list Space for Comments on page 14 Control activity Check note please cross yes no e The bolt connections are all securely fastened e Theluflok spot coated cylinder bolts M 12 x 30 have been used e The exit section is free from all dirt e Only corrosion proof bolt connections have been used e The Soll guided type fall arrester can only be inserted into the climbing path in the effective direction in which it travels Blocking device Fig 5 Detail 1 1 is on the left hand side e The stop bolt Fig 7 Detail 2 0 on the rear side of the exit section slips back into the locking bore Fig 7 Detail 1 2 hole independently e The stop bolt is free from dirt e The swivel part Fig 7 Detail 1 0 can be easily swivelled after pulling out the stop bolt The upper edge of the swivel part does not touch the upper guide rail when swivelling closed e The lower edge of the swivel part does not touch the lower guide rail when swivelling closed e The base Fig 7 Detail 3 0 plate is securely fitted e The guided type fall arrester does not slide out of the ladder guide rails joining to the top or the bottom whilst the swivel part is open e The guided type fall arrester can only be
6. lok spot coated cylinder bolt M12 x30 must be used Securing of bolts see section E Safety At Height Limited 8 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER soll by Honeywell D Inspection and acceptance All bolt connections are to be inspected They must be securely fastened and secured against loosening see section E The stop bolt Fig 7 item 2 0 on the rear side of the exit section must snap back into the locking bore hole independently The swivel part of the exit section must be easy to turn between the two ends of the guide rail E Bolt connections securing of bolts The stainless steel cylinder bolt M 12 x 30 is secured against self loosening by means of a Tuflok spot coating on the bolt For the ladders vertical guide rails and other accessories please observe the indications given inthe respective instructions Safety At Height Limited 9 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk F1 F 2 F 3 SAFETY MILLER by Honeywell Move the fall arrester into the swivel part 1 0 of the exit section Pull the stop bolt 2 0 on the rear of the base plate 3 0 backwards and turn the swivel part 1 0 Remove the fall arrester in an upward direction Warning Prior to the removal of the guided type fall arrester from the guide rail ensure that another form of protecti
7. ly and never thrown Before installation ladder sections must be cleaned from dirt in particular on connecting surfaces They should not come into contact with cement mortar or similar substances Remnants of mortar must be wiped off immediately Especially the sliding surfaces for the fall arrester on the inside and outside of the guide rail must be free of dirt Damaged parts may neither be used nor repaired but must be replaced by new ones Caution The ladder sections may be installed directly from the ladder and without any scaffolding The person installing the equipment uses a full body harness and a fall arrester In order to be protected against a fall from a height where the fall arrester slips from the rail or the not completely installed ladder bends backwards the installer must always use a safety lanyard with shock absorber in accordance to EN 354 355 or a retaining rope in accordance with EN 358 see Fig 1 Safety At Height Limited 4 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER sO by Honeywell Fig 1 B 8 Erection staff can during the installation secure themselves by using gt Safety lanyard acc to EN 354 355 connected to the center rail to the ladder under the highest situated properly secured mounting bracket gt The carabiner of a safety lanyard EN 354 355 is connected to a mounting bracket gt Support lanyard EN 358 route
8. on against a fall from a height is used The swivel part 1 0 should not stay open Though after removing the fall arrester and not closing it persons climbing afterwards cannot exit from the guide rail if the swivel part is open Inserting the guided type fall arrester Insert the fall arrester into the swivel part 1 0 with the safety pin pointing to the right Turn the swivel part back into alignment with the climbing path The stop bolt 2 0 on the rear side of the exit section snaps back into the locking bore hole 1 2 continue climbing Safety At Height Limited 1 0 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER G2 G3 G4 G5 G6 H1 H2 s l by Honeywell Maintenance of the exit section Warning For reasons of safety no repairs to any parts are to be carried out unless by qualified personnel Exit devices which have been damaged mechanically e g after a fall from a height must be exchanged The exit section must when required at least once a year be examined by a competent person to ensure itis in good working order Competent person is a person who thanks to his eduction and experience in the field of personal protective equipment against falls from height has sufficient knowledge about applicable state and local safety regulations applicable standards e g EN standards and is thus capable of judging the correct status
9. removed from the swivel part in an upward direction Test walk climb carried out e No defects or shortcomings were found PILI OU UO O OCO O OUL e These instructions were handed over to the operator e o Only original Sperian Fall Protection Deutschland GmbH amp Co KG FP OOUUO O OO O OOU OU ULU E Fall Protection Engineering components were used Safety at nine Limited 1 3 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk Installation Site Owner Street City Telephone Fax Manual handetover to MILLER by Honeywell Installing company Street City Telephone Fax name site operator or representative signature Chief engineer of the installing company Place Date name signature Defects irregularities and deviations from the checklist must be noted here Noted defects shortcomings Tel 44 0 161 446 5615 competent person installer signature date Safety At Height Limited 1 4 Unit 1 Pennine View Marple Stockport Cheshire SK67JW www safety height co uk
10. rized with these instructions prior to using the system Use which is not in accordance with these instructions constitutes a risk to human life The operator of the fall protection system must ensure that these instructions are either e retained ina dry and secure condition at the installation or e retained by the operator whereby he or she must ensure that the user is aware of the storage location of these instructions and that the documents are accessible at all times lf requested the plant operator must present these instructions to the manufacturer of the fall protection system Sperian Fall Protection Deutschland GmbH amp Co KG or a dealer authorized by the same The SOLL fall protection system must be used in accordance with the instructions for the relevant SOLL fall arrester The fitment and use of SOLL accessories to such fall protection systems must strictly adhere to the relevant instructions for the fitment and use thereof In case of the use of further personal protective equipment relevant instructions must be followed National regulations on accident prevention and use of safety equipment for construction work must be adhered to Soll fall protection systems may only be fitted and used with original Soll components elements The combination with non original components elements may influence the safety of SOLL fall protection systems In such cases Sperian Fall Protection Deutschland GmbH amp Co KG and a dealer
Download Pdf Manuals
Related Search