Söll GlideLoc Comfort Fall Arrester user manual
Contents
1. 44809 Bochum CE 0158 A10 The maximum arrest distance when dynamically tested in accordance with the requirements of the CSA Z259 2 2 98 standard amounts to 1m A11 Use of the fall arrester is not suitable when the user is positioned on an un stable surface fine grain material or particulate B Inspection before climbing B 1 Before using the guide the fall arrester intermediate joint and karabiner hooks always check their usage capability and correct functioning See the Maintenance check list for this purpose B 2 Do not use the fall arrester system if there are apparent defects or doubts regarding the safety of the system Do not use it until an expert approves it for further use Send the system components back to the manufacturer if required B 3 Before and while climbing ensure safe and effective implementation of res cue measures B 4 The user must be in good health and must not be under the influence of alco hol drugs or medicines B 5 Note Utmost care must be taken when ascending and descending in the first 2 m of the ascent route since it may not be possible to prevent the user from hitting the ground in some cases B 6 Warning The specific influence of the arresting mechanism when ascending and de scending may hamper the safe functioning of the fall arrester Safety At Height Limited 4 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk S2. 1 0 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell Maintenance check list see Figure 6 for this Body 1 0 e Free from colour mortar concrete dirt etc e The marking 1 9 on the lower side must be clearly legible e The locking pin 1 2 fits firmly and is not bent check by turning it e Running surfaces 1 1 must be clean e Sliding pieces 1 4 must be available e Sliding pieces 1 4 must not be worn out e Rubber belt 1 6 is available and not damaged e Stickers 1 7 1 8 are available and not damaged e Engraved arrow 1 10 can be easily identified Latch 2 0 e It must move freely e It must not be deformed 2 2 maximum 58 mm e Interception catch length 2 1 14 0 mm 1 0 0 5 mm Running rollers 1 3 total 10 units e Axial clearance maximum 0 5 mm e They must rotate freely concentricity e They must not be damaged e They must fit firmly on the axle e The minimum diameter of running rollers 1 3 must be 9 mm Compression springs 1 5 e They must be free from rust e They must be free from dirt concrete colour etc e They must not be broken e They must not slip not relevant for safety Safety At Height Limited 11 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell Rotary shackle 3 0 e It
3. AFETY MILLER AT HEIGHT by Honeywell C Using the fall arrester Figure 1 Warning The fall arrester system and the full body harness secure the users against falling when ascending or descending When working in or next to the ascent route and when executing tasks and actions that are not a part of the usual ascent and descent movements the climber must additionally secure himself herself with a lanyard in accordance with EN 354 or CSA approved or a lanyard for the working positioning belts in accordance with EN 358 or CSA approved Safety using an anchor device This is also applicable for posi tions that are intended to take a break on the ladder Only suitable anchor devices such as a mounting bracket must be used for this In all these situati ons the lanyard must be held tight in order to prevent a fall see figure 1 C Figure 1 EN 354 355 An EN 353 1 compliant fall arrester system should be used only by those per sons who e are trained and or are otherwise competent or e are directly supervised by a trained and or a competent person Safety At Height Limited 5 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell Figure 2 C 2 Push the fall arrester into the lower end of the anchorage rail 6 0 or in the recess 6 1 that must always be provided at the stomach height or deeper see view A The laterally
4. Figure 6 detail 1 3 have plain bearings and have been lubricated in the factory F 3 Lubricate the rotary shackle Figure 6 detail 3 0 slightly F 4 Lubricate the knurled bushing Figure 6 detail 4 1 5 1 if required F 5 Attention Do not bring the fall arrester in contact with chemicals G Storage The fall arrester should be kept clean and as dry and dust free as possible and should not be stored near heat sources When transporting ensure that the fall arrester is protected from damage Safety At Height Limited 14 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell H Inspection logbook Reason for working on the Date of the system regular inspection next regular or repair inspection Safety At Height Limited 1 5 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk
5. SAFETY MILLER by Honeywell Usage and maintenance manual for the fall arrester system of the Soll GlideLoc type with a guided type fall arrester S ll Comfort Order No 22697 with self locking karabiner hooks Order No 22690 with bolted karabiner hooks in accordance with EN 353 1 2002 CNB P 11 073 and CSA Z2259 2 1 98 Serial number Date of purchase The initial test is done by the manufacturer before shipment The yearly inspections have to be documented in the inspection logbook The user must fill in the following details using an indelible pen Date of commissioning Operating company user Street Location Tel Fax Safety At Height Limited Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk 1 SAFETY MILLER AT HEIGHT nr Contents Page A General information 3 B Inspection before climbing 4 C Using the fall arrester 5 D Removing the fall arrester 9 E Maintenance 9 F Care 14 G Storage 14 H Inspection logbook 15 This manual is protected by copyright Duplicating and circulating this manual is not permitted without written consent of the author as per 16 17 Ger man Copyright Act UrhG and Honeywell Fall Protection Deutschland GmbH amp Co KG reserves the right to prose cute as per 106 German Copyright Act UrhG in case of any violation Changes in this edition Page 1 Definition initial test yearly insp
6. arple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER by Honeywell sol 7 y E 3 Expert test also see Figure 6 for this Use the maintenance check list for the expert test An expert can rectify the following defects e Removing dirt concrete mortar colour etc on the body and running sur faces e Cleaning the labels e Replacing the stickers In case of dirt inside the shuttle and defects that necessitate partial dismant ling of components the shuttle must be sent to the manufacturer s workshop with suitable notification and with the manual to rectify the defects This process must be recorded in the annexe of the check list space for com ments Owing to safety reasons repairs may be carried out only the manufacturer s workshop Figure 5 Example of ma Figure 5 259 2 1 Clase FRL Year of manufacture X 00 Serial number 0000 CE 0158 monitoring testing agency Ta Note for reading the operating manual S ll GlideLoc type designation of the fall arrester system EN 353 1 2002 reference to the European standard CNB P 11 073 reference to additional test regulations GE approval mark for Canada Z259 2 1 Class FRL reference to the Canadian standard min 40 kg max 140 kg minimum maximum weight of the user Once the expert ensures that the maintenance is fault free he she can affix a test label on the fall arrester Safety At Height Limited
7. can be moved e It must not be broken e It must not have cracks e The thickness of the rotary shackle 3 0 must be at least 5 5 mm e The shackle axle 3 1 is riveted e The maximum outer dimension of shackle pin eyelets 3 2 must be 40 mm Karabiner hook 4 0 5 0 e It must not be bent e It must not have cracks e It must not be broken e The knurled bushing 4 1 5 1 must not be damaged e It must be possible to open the knurled bushing 4 1 easily e The knurled bushing 4 1 must close and lock automatically after opening and releasing e It must be possible to open and close the knurled bushing 5 1 easily open and close e The special nut 5 2 must not be damaged e The locking pin 4 3 5 3 must be available Space for comments Safety At Height Limited 12 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY AT HEIGHT MULLER by Honeywell Figure 6 ore wau Bice gi Sal Sideloe men 225001 le Jri CHBPNI 78 ff Clase iu Safety At Height Limited 1 3 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 SAFETY MILLER AT HEIGHT by Honeywell soll F Care F 1 Wash the entire fall arrester with water and dry it using a suction cloth Do not use heat sources for drying DO NOT wash it with a quick cleaner thinner or degreaser containing trichlo roethane Do not use grease F 2 Running rollers
8. ection Safety At Height Limited 2 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER by Honeywell A General information Note EN standards references apply to users of the product in the European Union CSA standards references apply to users in Canada CSA certification is appli cable to the fall arrester and rail system only A 1 Read this manual and understand its contents before usage Actions contrave ning this manual may put people s lives at risk Note The Soll Comfort fall arrester may not be used in explosion prone areas A 2 For the users safety it is important that the retailer provides this manual in respective country s language if this system is re sold in another country A 3 The maximum user load including the clothing and equipment may not exceed 140 kg Operating temperature for the fall protection system 40 C to 70 C A 4 A safety distance of 3 0 m between the users must not be undershot A 5 The regulations for using personal protective equipment against falls from a height i e BGR 198 of the Institute for statutory accident insurance and pre vention as well as the rules for using personal protective equipment for holding and rescuing i e BGR 199 must be observed A6 The Soll Comfort fall arrester is component of the Soll fall protection system with a fixed guide of the Soll GlideLoc type c
9. eight Limited 8 Unit 1 Pennine View Marple Stockport Cheshire SK67JW B 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell D Removing the fall arrester from the anchorage rail Warning Protection against falls from heights must be ensured using a different me thod before removing the fall arrester from the anchorage rail D To remove the fall arrester from the anchorage rail the corresponding end stop Figure 2 detail 7 0 must be crossed For this fold the locking latch Figure 2 detail 7 1 of the end stop upwards downwards When using an exiting device observe its valid operating manual E Maintenance E A fall arrester system damaged due to a fall must be used again only after testing by an expert The fall arrester and the manual must be sent to the manufacturer s workshop for checking and maintenance E 2 Depending on the application and operating conditions an expert must check the fall arrester system for its flawless condition as required however at least once a year An expert for the personal protective equipment is A person who can has a certificate for successfully participating in a course compliant with the fundamental principles for selecting and training the ex perts in the field of personal protective equipment against falls from a height and certifying their qualification i e BGG 906 Safety At Height Limited 9 Unit 1 Pennine View M
10. illustration self locking karabiner hooks TNS LLL SRS OLY 7777 J oo S GE E A N E E Q 3 front D ring of f harness harness y K Z Correct Incorrect bod Safety At Height Limited 7 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER by Honeywell Figure 4 Warning Risk to life The karabiner hook of the fall arrester must be directly inserted into the front arrester element marking with A of the full body harness for the vertical and horizontal usage in compliance with EN 353 1 CSA requires that the device is connected directly to the front arrest element of a class AL harness The length between the outer edge of the anchorage rail and the internally bent eyelet on the harness as required by both EN and CSA stan dards may not exceed 200 mm see Figure 3 Figure 4 Front arrester element WN reno VERN Attachment element Attachment element C 4 The stomach or chest harness of the full body harness must fit firmly on the body see Figure 3 C 5 The ladder can now be used When descending the latch Figure 6 Detail 2 0 of the fall arrester must be unlocked Two options are available for this a The user can lean backwards and unlock the latch b If the user goes near the ladder the fall arrester suspends downwards The latch is unlocked due to the weight of the fall arrester Safety At H
11. ompliant with EN 353 Part 1 and has been designed for use as personal protective equipment only for the intended use of the Soll fall protection system The operating company of the fall arrester system must suitably ensure that the full body harness and the fall arrester belong to the user and that they are used according to the instructions After use the fall arrester must not be left inside the fall protection system The Soll Comfort fall arrester must be operated only in the original Soll fall arrester systems that have the Soll GlideLoc type EG test certificate Using systems of other manufacturers may hamper the functioning of the fall arrester In such cases Honeywell Fall Protection Deutschland GmbH amp Co KG and its authorised dealers refuse product liability The operating company shall then be completely responsible Safety At Height Limited 3 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell A 7 Full body harnesses must be approved in accordance with EN 361 or CSA Z259 10 class AL Only certified arrester elements marking with A may be used Note The fall arrester Comfort must always be connected with the certified arre ster element of the harness A8 The fall arrester should always be handled in a manner that will protect it from damage or corrosion AQ Relevant notified body DEKRA EXAM GmbH Dinnendahlstr 9
12. protruding locking pin 1 2 must be on the right side and the engraved arrow 1 10 on the side of the fall arrester must point upwards The locking pin 1 2 and the end stop 7 0 prevent the incorrect use of the fall arrester and unintended slipping from the anchorage rail Figure 2 illustration self locking karabiner hooks S m 000 OOOO OO OO OOO OOOO OOOO OOO OO PO OOOO Warning Crossing the end stop is allowed only e inthe areas without the risk of a fall from heights or e if the safety against falls from heights is ensured using other means Safety At Height Limited 6 Unit 1 Pennine View Marple Stockport Cheshire SK67JW Tel 44 0 161 446 5615 www safety height co uk SAFETY MILLER AT HEIGHT by Honeywell Figure 3 C 3 Open the karabiner hook 4 0 5 0 on the fall arrester a In case of the self locking karabiner hook turn back the knurled bus hing 4 1 and push it inwards b In case of the bolted karabiner hook turn back the knurled bushing 5 1 Figure 6 entirely and push it inwards Attach it directly to the front arrester element of the full body harness a In case of the self locking karabiner hook the knurled bushing 4 1 must lock automatically once it is released b In case of bolted karabiner hook tighten the knurled bushing 5 1 Figure 6 again Attention An unsecured karabiner hook open knurled bushing is dangerous to human life Figure 3
Download Pdf Manuals
Related Search