INSTALLATION AND SERVICE MANUAL FOR TAG
Contents
1. a clear plex cut to the same size Use your original plex as a template when cutting the new Underlay Card down to size Remove the marquee plex Use this plex as a template when cutting the new Marquee plex down to size Remove the control panel from the cabinet and strip it down The game is now ready to be converted PAGE 4 INSTALLATION amp SERVICE MANUAL e Installation procedures Control Panel This is never any fun so lets do it first and get it out of the way Examine the suggested control panel layout drawing refer to Chapter 2 Specific Information and see what holes you will have to add and or plug Install the control panel overlay by peeling off the paper backing and carefully lowering it down on to the panel Smooth it out starting from the center and work your way out to the edges removing all of the trapped air pockets Using a sharp blade cut out all of the required holes and mount the controls as shown in the layout drawing Mount the completed control panel to the cabinet PCB Set Mount the new pcb set into the cabinet We recommend mounting these to a side wall to allow for adequate convection cooling This pcb set does not require an EMI cage but use of the EMI Filter pcb is MANDATORY Tag Team does not have a EMI Filter pcb nor does it require one Main Harness Plug the Main Harness onto the edge connector of the EMI Filter pcb and route the power supply wires neatly to the power supply For best resul2. in your kit IT IS THE RESPONSIBILITY OF THE PERSON PERFORMING THE CONVERSION TO COMPLY WITH ALL LABELING REQUIREMENTS INSTALLATION amp SERVICE MANUAL PAGE 3 d Conversion preparations Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit This section will cover the basic procedures to follow when preparing your game FIND THE WIRING DIAGRAM FOR THE GAME TO BE CONVERTED You will need to identify the required DC power supply output wires and the monitor video and sync wires Note the color coding of these wires or better yet label each one as to their function This conversion kit contains a new Main Harness but you may need to splice into the existing power supply and monitor wires Remove the existing game harnesses that will not be utilized in the final conversion NOTE This conversion kit only requires modification of the secondary DC from power supply and I O control panel and coin sections of the original wiring DO NOT REMOVE OR MODIFY THE PRIMARY AC WIRING The primary AC wiring should have been designed and built to UL and FCC regulations and must not be modified Remove the existing game logic boards Remove all decals and or paint over existing cabinet graphics Repair any cabinet damage at this time Remove the monitor plex or glass If your plex has silkscreened artwork on it you will need to strip it off or replace with
3. MINIMUM OF 1 AMPERE 5 VOLTS AT A MINIMUM OF 5 AMPERE When selecting a game to convert make sure that the coin acceptors are functional the monitor and power supply work well and the cabinet is structurally sound There is nothing more frustrating then installing a new conversion kit and discovering that it will not come up due to a faulty monitor or power supply I know the first thing we will suspect is the new Logic PCB right Save yourself some time and money by making sure the original game Works before you install the conversion kit It it mandatory that the cabinet be wired to conform with all National and Local Electrical Code requirements before the conversion is attempted The system must have adequate noise filtering on the AC line to prevent unwanted conducted radio frequency interference Adequate is defined as a filter having both common mode and differential mode filtering with a current capacity of at least 1 1 2 amperes According to the FCC and or other regulatory agencies every video game must be clearly labeled with the name and address of the Original Manufacturer Date of Manufacture or serial number Voltage Rating Current Rating Suitability for indoor or outdoor use and Model Number In addition the FCC requires that after conversion the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area An acceptable warning sticker is included
4. lm i Kerg WI INSTALLATION AND SERVICE MANUAL FOR TAG TEAM WRESTLING KARATE CHAMP PLAYER vs PLAYER KUNG FU MASTER COMMANDO AND SHOOTOUT PCB CONVERSION KITS BY DATA EAST USDA Inc 780 0055 00 INSTALLATION AND SERVICE FOR DATA EAST CONVERSION TABLE OF CONTENTS 1 GENERAL INFORMATION a Warnings and service information b Warranty information e e e e c General conversion requirements d Conversion preparations EE e Installation procedures mm 2 SPECIFIC INFORMATION a Tag Team Wrestling eee ree b Karate Champ player vs player c Kung Fu Master ce eee eee eee d C mm nd 44 vA ewes RE RAT AE ha ER s ShO OULOUL uw os XC RURSUS Tees C 1987 DATA EAST USA INC ATO NEEDLES DR SAN JOSE CA 95112 408 286 7074 Let Printing February 1987 MANUAL KITS 780 0055 00 C General conversion requirements This Data East conversion kit is designed to be installed into an existing video game cabinet All necessary components and graphics have been supplied to make the results of this conversion look and play like a new upright game There are several requirements to consider when selecting a game to convert They are as follows COLOR MONITOR VERTICAL HORIZONTAL TAG TEAM WRESTLING KUNG FU MASTER KARATE CHAMP SHOOTOUT COMMANDO POWER SUPPLY 5 VOLTS AT A MINIMUM OF 7 AMPERES 12 VOLTS AT A
5. place at this time Apply the side decals being careful to remove all air pockets MANDATORY Install the FCC warning label to the back of the cabinet to complete the installation procedures The Big Test Before applying power to the game go back and verify that the wiring is correct DISCONNECT THE PCB EDGE CONNECTOR NOW With the pcb edge connector disconnected apply power and MEASURE WITH A DIGITAL MULTIMETER the 5 volt level in respect to ground AT THE EDGE CONNECTOR Refer to the edge connector pin out in Section 2 Specific Information Adjust the power supply to get a 5 1 volt reading at this point Check the 12 volt level and the 5 volt if required level in the same manner REMOVE POW R FROM THE GAME iND ALLOW 1 MINUTE FOR THE POWER SUPPLY TO DISCHARGE F e Reinstall the pcb edge connector and apply power to the game The game s attract mode video should appear on the screen Examine the video for correct appearance Adjust the controls on the monitor to get the optimum picture as required sound Well coin it up and play it Check for proper controls vider E eS S ED PAGE 6 INSTALLATION amp SERVICE MANUAL
6. ts these wires should be routed in such a way as to keep the overall length to a minimum Use a minimum of two 2 wires EACH for the 5 volt and Ground wires from the Power Supply to the pcb set The 12 volt wire is not critical one 1 wire is adequate Terminate these wires as required by your particular application WARNING IMMROPER WIRING WILL CAUSE SUBSTANTIAL DAMAGE TO THE PCB SET AND VOID YOUR WARRANTY t Route the remaining wires to their proper destinations cut to the proper length and terminate as required See Specific Wiring Information for hook up details NOTE As mentioned in the Conversion Requirements this pcb set outputs NEGATIVE COMPOSITE SYNC to the monitor If your monitor does not support Composite Sync hook the Sync wire to the Horizontal Sync input This method will work on most monitors however some Electrohome models require that Sync be tied to both the Horizontal and Vertical inputs for proper operation Contact your distributor if you are uncertain as to the proper hook up procedures for your monitor INSTALLATION amp SERVICE MANUAL l PAGE 5 b Installation procures continued The Coin Counter s can be 5 volt or 12 volt units as the pcb set utilizes an Open Collector output driver circuit See Specific Wiring Information for hook up details Graphics Install the Underlay Card This card will rest directly under che clear monitor plex or glass Mount the new Marquee Plex in
Download Pdf Manuals
Related Search