Service Manual for RESmart AutoCPAP
Contents
1. Screen bottom Sag H imos st His one AC Inlet Communications Humidifier Oo Controller Connector Air Outlet Filter Cap amp Filter Humidifier Power Outlet Port Indicator ew Light a Heater Plate 0 Fill Line gt S Chamber 2 2 Inner Construction See appendix A 2 3 Spare Part See appendix B Service Manual for RESmart AutoCPAP V1 0 3 Software 3 1 Instruction for Upgrading Device Software 1 Power off the RESmart CPAP AutoCPAP device then connect PC and the device via data cable 2 Run the software BMC RESmart Tools for Upgrade from PC and display as below BEC Resmart Auto CPAP Tools for Upgrade Upgrade File Auto1 28 A upd Browse Serial Port COM1 x OK a Select the right Upgrade File for example version 1 28 for AutoCPAP is Auto1 28 A upd b Select the right serial port default is COM1 3 Click OK display as below Waiting for APAP s reset Please disconnect the power supply of the device wait for over 5 seconds to make sure that the device is reset and connect the power cable again Waiting for the reset of the device Power on the CPAP AutoCPAP device If the device is power on from beginning please power off the device and turn on again after 5 seconds more 4 After the device is turned on the following will display Service Manual for RESmart AutoCP2. AC Socket Fig E Power supply connecting Orange Orange 2 pin plug Reed amp pin plug Service Manual for RESmart AutoCPAP V1 0 Fig F Power supply to humidifier Left Right Connecting relationship Part 1 2 3 4 Fig D Back of device Fig C CN1 E Fig C CN2 Fig A P24 Fig F Left Fig F Right Blower 8 pin plug Fig A PM Table 2 Service Manual for RESmart AutoCPAP V1 0 2 Humidifier Fig G Humidifier PCBA back side Pl Fig H Power supply to humidifier Power Supply to Humidifier Service Manual for RESmart AutoCPAP V1 0 Fig Heater PCBA 4pin Plus 3 pin Plug an ag Power Reed to Humidifier Heater PCBA Connecting relationship Part 1 2 3 4 Fig l Fig G P2 Fig G P1 Fig H Left Fig H Right Table 3 Service Manual for RESmart AutoCPAP V1 0 Components Illumination 1 Device Inside S N Assembly 1 Insert humidifier locker on the shield bottom Orange Black Insert humidifier power supply reed on the N p shield bottom as per Fig E and F Bie r Assembly the humidifier locker and button spring t 8 Put fixin
3. fixing to handle and fix by 19 screw 4X 3mm 8mm 20 Assembly the infrared window Infrared Window 21 Assembly and fix the panel 23 Put on the key button Assembly shield cover on the bottom adjust 24 the position of outlet and make sure it is clamped in the right socket Screw Hole 25 Fix the shield by screws 4X M3 10mm 26 Stick four device pads R Pad 27 Putin filter and assembly the cover lug up 28 Put on all plugs if necessary without ower plug humidifier Plug down Service Manual for RESmart AutoCPAP V1 0 3 Humidifier S N Assembly Black As per Fig H assembly the heater plane and wire Fix them by screw 3mm 8mm Put spring on each of three poles on heater 2 plane 3 Assembly the scaleboard on the heater plane and fix by screw 3mm 8mm 4 As per Table 3 assembly heater PCBA and wires 5 Put the humidifier inner connector on the shield 6 Put on light window 7 Assembly the inner and outer shield 20 Service Manual for RESmart AutoCPAP V1 0 8 Fix on screw M3 10mm Screw Appendix B Spare Part Configuration Service Manual for RESmart AutoCPAP V1 0 S N Name Qty Figure 1 Shield Cover 1 2 Handle 1 3 Handle Fixing 2 4 Shield Bottom 1 5 Humidifier Clip 1 6 Humidifier Locker 1
4. 0 3 Onn 1 3 0 3 ue Replace 0 3 Replace Replace Main Bogrd Replace Motor Replace Main Board Inner Airway Connector Rewrite Corest Softwar Service Manual for RESmart AutoCPAP V1 0 4 2 Error List and Information Error Index Problem Causing Error 1 Over temperature inside Malfunction on main board Error 2 Motor stop Malfunction on motor or controller Error 3 Motor low speed Malfunction on motor Error 4 Low temperature inside Malfunction on main board Error 8 Wrong software version Software 10 Service Manual for RESmart AutoCPAP V1 0 Device Configuration 1 Main device Fig A Main board bac Appendices Fig B Outlet leftside 2 q EGIL I Hole 1 2 and 3 in Fig B connect to sensor YL and LL via silicon rubber canal Specified in Table 1 Fig B Fig A Specification of canal 1 Hole 1 on sensor YL 2mm 4mm Li2cm 2 Hole 2 on sensor LL 2mm P4mm L12cm Hole 1 on sensor LL 2mm P4mm L8cm Table 1 Service Manual for RESmart AutoCPAP V1 0 Fig C Power PCBA front side Fig D Wire connecting on power PCBA Sockets figuration IND N2 Spin plug
5. AP V1 0 Upgrading Click Upgrade to start upgrading the device Cancel Click Upgrade to start If success the right version number will be displayed on CPAP AutoCPAP device screen when every power on Note If failed during upgrading please repeat from above 1 4 steps If Error 08 displayed after software upgrading it means unmatched software used for example apply AutoCPAP software to CPAP device In this case apply correct software and upgrade again 3 2 Hidden Function 1 Humidifier matching and dis matching Available on version 1 19 and later Assemble humidifier on main device do not apply water tank Enter maintenance menu set Treat P 3 and Ramp 40 then press On Off button when Manual P appears Thus the humidifier is matched When OK appears on LCD humidifier matching successes If cut the power supply after pressing On Off button when Manual P appears then the humidifier is dis matched Reset Available on version 1 28 and later Enter maintenance menu press Ramp button for 5 seconds more thus hidden date setting appears Set YYYY MM DD 2097 07 01 press On Off when Hour setting thus all device setting and therapy record not include use time and days are reset If set Minute 16 during above procedure then not only device setting and therapy record but also patient information are reset If set Minute 26 during
6. Service Manual for RESmart AutoCPAP V1 0 BMG RESmart AutoCPAP System Service Manual Service Manual for RESmart AutoCPAP V1 0 Important All data in this manual have been verified correctly It is sufficient for servicing and repairing this device If applying this manual on other purpose the validation should be confirmed by BMC Medical Co Other wise BMC Medical Co has no responsibility for the result All information in this manual is protected by law and regulation All copyrights are belongs to BMC Medical Co INPORTANT CAUTION AND WARNING in this manual are to emphasize dangers to service people WARNING If do not operate properly may cause damage to people and environment CAUTION If do not operate properly may cause damage to instrument IMPORTANT Important information for servicing and repairing Safety Notice Electric Shock There is above 100VAC voltage inside this device please be sure to repair device after power off Chemical Safety There may be risk of virus after touching by patient Please clean device or wear protective glove before servicing and repairing Please deal with the waste according to regulation Wash hands by disinfector after operating this device v Service Manual for RESmart AutoCPAP V1 0 Table of Contents Important 1 Introduction 1 1 Intended Use 1 2 Implement 2 Structure 2 1 Outer Illumination 2 2 Inner Construc
7. T Humidifier Fixing 1 8 Filter Cover 1 9 Shield Back 1 10 Outlet 1 Service Manual for RESmart AutoCPAP V1 0 11 PCBA Fixing 2 12 Infrared Window 2 13 Panel 1 Humidifier Outer 1 Shield Humidifier I 15 umidii nner 1 Shield 16 Light Window 1 17 Pole Platelet 1 Humidifier Power 18 1 Plug 19 Humidifier Plug 1 left up 20 Humidifier Plug 1 left down 21 Humidifier Plug 1 right up 23 Service Manual for RESmart AutoCPAP V1 0 22 Humidifier Plug 1 right down 23 Device Pad 6 0 24 Blower Connector 1 CI Humidifier 25 umidifier Inner i Connector 26 Key Button 1 Gas Humidifi 27 umidifier 1 dd Scaleboard 28 Heater Plane Spring 3 ETE 29 Button Spring 1 6 24 Service Manual for RESmart AutoCPAP V1 0 Spare Part List Part Name S N Qty Unit Classify Use Main Board PCBA 20211261 1 PC PCBA Main Device Heater PCBA 20212 41 1 PC PCBA Humidifier Power Supply PCBA 20311101 1 PC PCBA Main Device Blower 40211 1 PC Assembly Main Device Heater Plane 45010101 1 Set Assembly Humidifier Power Supply PCBA Wire 45010201 1 Set Wire Main Device Main Board PCBA Wire 45010301 1 Set Wire Main Device Silicon Rubber Canal 50224 1 PC Assembly Main Device Silicon Rubber Canal 50224 1 PC A
8. above procedure then not only device setting therapy record and patient information but also use time and days are reset 3 Pressure calibration Service Manual for RESmart AutoCPAP V1 0 Available on version 1 20 and later Connect pressure meter to the gas outlet in the device enter hidden date setting set YYYY MM DD 2098 08 08 press On Off when Hour setting thus pressure calibration starts The device increases pressure to 20hPa cmH20 AD sampling data will appear on LCD When LCD data displaying is stable if pressure meter value is not 20 press button to adjust the pressure output Until output pressure value is 20 and LCD displays stable press On Off button to finish pressure calibration Debug mode Available on version 1 19 and later Enter hidden date setting set YYYY MM DD 2099 08 02 or 03 press On Off when Hour setting thus debug 02 or 03 mode starts The device can send real time data to computer via serial port Only cutting off power supply can make device back to normal mode Service Manual for RESmart AutoCPAP V1 0 4 Malfunction and Countermeasure 4 1 Malfunction Determination No Power Can Start Up Humidifier Aiddng 1amog apo mod Over Temperathre Software Upgrade Motor Stop Motor Low Speed Law Temperatur Low Temperature Replace Main Boa N O 4 4 m Deon
9. g on the spring and fix by screw 2X B 4 3mm 8mm Power wire to 5 Put power wire humidifier Assembly the shield back on the bottom fix by screw 2X3mm 8mm 7 Assembly foam bottom into shield bottom Assembly AC power socket on the shield back character face up Service Manual for RESmart AutoCPAP V1 0 9 Clean up the wire 10 Assembly power PCBA in the socket and connect all plugs Clean up the wire 11 Connect outlet to blower connector fix by clip 1 Connect blower to connector and fix by clip Put the integrated one in the right place 13 Covered by foam cover and clean up wires PCBA Fixing 14 Assembly fixing clip on the main board PCBA Clip Pressure Sensor Plug the 8 pin plug of blower in the socket PM 15 plug 2 as in Fig E in the socket P24 on the main board PCBA Service Manual for RESmart AutoCPAP V1 0 Assembly the main board PCBA on fixing pole PCBA Fixing Pole 2 Connect sensor LL to outlet by silicon rubber canal 16 and make sure the clip clamps power PCBA 1 As per Table 1 connect sensor YL to outlet by silicon rubber canal 17 12cm canal for YL sensor Sem canal for LL sensor 12cm canal for LL sensor 2 Device Outside S N Assembly 18 Put handle in the socket on shield cover Service Manual for RESmart AutoCPAP V1 0 Assembly handle
10. r Main Device Device Pad 4012110601 6 PC Rubber All Key Button 4012110701 1 PC Rubber Main Device Service Manual for RESmart AutoCPAP V1 0 Blower Connector 4012110801 1 PC Rubber Main Device Humidifier Inner Connector 4012110901 1 PC Rubber Humidifier Screw 1 8 PC Screw All Screw 2 9 PC Screw All Sunk Screw 4 PC Screw Main Device Filter 1 PC Accessory All Power Cord 33011101 1 PC Accessory All 26
11. ssembly Main Device Foam bottom 40191 0101 1 PC Foam Main Device Foam cover 40191 0201 1 PC Foam Main Device Shied Cover 4011120101 1 PC Plastic Main Device Handle 4011120201 1 PC Plastic Main Device Handle Fixing 40111 0301 2 PC Plastic Main Device Shield Bottom 4011120401 1 PC Plastic Main Device Humidifier Clip 4011120501 1 PC Plastic Main Device Humidifier Locker 40111 0601 1 PC Plastic Main Device Humidifier Fixing 40111 0701 1 PC Plastic Main Device Filter Cover 4011120801 1 PC Plastic Main Device Shield Back 4011120901 1 PC Plastic Main Device Outlet 4011123001 1 Set Plastic Main Device PCBA Fixing 40111 1301 2 PC Plastic Main Device Infrared Window 4011101401 2 PC Plastic Main Device Panel 4011220101 1 PC Plastic Main Device Power Supply PCBA Fixing 40111 1601 1 PC Plastic Main Device Humidifier Outer Shield 4011122201 1 PC Plastic Humidifier Humidifier Inner Shield 4011122301 1 PC Plastic Humidifier Pole Platelet 40111 2601 1 PC Plastic Humidifier Light Window 4011142401 1 PC Plastic Humidifier Button Spring 4013140101 1 PC Metal Main Device Humidifier Scaleboard 4013130401 1 PC Metal Humidifier Heater Plane Spring 4013140501 3 PC Metal Humidifier Humidifier Power Plug 4012110101 1 PC Rubber Main Device Humidifier Plug left up 4012110201 1 PC Rubber Main Device Humidifier Plug left down 4012110301 1 PC Rubber Main Device Humidifier Plug right up 4012110401 1 PC Rubber Main Device Humidifier Plug right down 4012110501 1 PC Rubbe
12. tion 2 2 Spare Part 3 Software 3 1 Upgrade 3 2 Hidden Function 4 Malfunction and Countermeasure 4 1 Malfunction Determination 4 2 Error List and Information Appendices Appendix A Appendix B Service Manual for RESmart AutoCPAP V1 0 1 Introduction 1 1 Intended Use The RESmart Auto system is a CPAP Continuous Positive Airway Pressure device designed for the treatment of adult Obstructive Sleep Apnea OSA only The RESmart Auto is to be used only on the instruction of a licensed health care professional Your home care provider will make the correct pressure settings according to your health care professional s prescription This device is not intended for life support This service manual is used to help service people maintenance RESmart AutoCPAP system of BMC Medical Co more efficiently Instructions in this manual may help device work best Engineer can find needed instruction from this manual quickly IMPORTANT Read and understand instruction in this manual before operating IMPORTANT RESmart AutoCPAP system can not be used for life support 1 2 Implement 1 Implement for repairing Type screw driver Pincers 2 Implement for measuring Pressure meter Service Manual for RESmart AutoCPAP V1 0 2 Structure 2 1 Outer Illumination Medical Handle EN Product Note co pe
Download Pdf Manuals
Related Search