The Tiny Tim User's Guide
Contents
1. and tiny2 will generate a PSF for each position with output filenames like test00 testO1 e Date of observation used to compute focus and aberrations which are time dependent Field Dependence and Aberrations Like WFPC2 the obscurations in the WF PC 1 optics appeared to shift relative to the telescope s depending on field position The effect of this shifting was more pronounced in WF PC 1 because of the spherical aberration which caused shadows of the camera obscurations and the telescope mirror support pads The increased beam size due to the aberration also caused vignetting at the edges of the field in the WECs These variations made deconvolution difficult since the positions of the shadows in the wings could change significantly with field offsets of only tens of pixels The resulting mismatches would lead to residuals in the wings of the PSFs Since Tiny Tim models can be generated for any position an optimum PSF can be used for wherever the object is on the detector WF PC 1 was known to have field dependent aberrations focus coma and astigmatism but they were not well characterized The aberrations for the center of the field in each camera are used for all positions in Tiny Tim WF PC 1 also suffered from geometric distortion which is not modeled The WF PC 1 detectors must have had charge diffusion blurring like that in WFPC2 but its effect was not noticeable due to the blurring caused by spherical aber2. Large angle scattering in WFPC2 and horizontal smearing correction WFPC2 ISR 94 01 Krist J E amp Hook R 1997 NICMOS PSF variations and Tiny Tim simulations Proceedings of the 1997 HST Calibration Workshop p 192 Krist J E et al 1998 Characterization and subtraction of well exposed HST NICMOS Camera 2 point spread functions for a survey of very low mass companions to nearby stars P A S P 110 1046 Lauer T 1999 The photometry of undersampled point spread functions P A S P 111 1434 Storrs A et al 1999 Camera 3 Intrapixel Sensitivity NICMOS ISR 99 005 Suchkov A amp Galas G 1999 NICMOS optical aberrations coma and astigmatism NICMOS ISR 99 003 Suchkov A amp Krist J 1998 Tiny Tim modeling of NICMOS PSF subtraction effects of focus breathing cold mask wiggling and color variations NICMOS ISR 98 018 31 Appendix B How PSFs are Simulated The following is a brief description of how Tiny Tim simulates PSFs For a more thorough discussion of HST optics and diffraction optics check out Astronomical Optics by Daniel Schroeder A PSF is the diffraction pattern caused by light from a point source passing through an optical system with the various optical components and obscurations adding structure to it In the case of HST the obscurations include the entrance aperture the secondary mirror and spider vanes the support pads on the primary mirror
3. 2 69765e 12 yx 2 18297e 11 x V3 254 554 0 0494753 y 0 0019787 x 3 98757e 7 y 2 95496e 7 yx 7 73173e 8 x 2 05943e 11 y 2 25953e 12 y x 2 5169e 11 yx 3 28721e 12 x HRC V2 176 691 0 00138315 y 0 0283538 x 9 44458e 9 y 2 12941e 7 yx 6 66749e 8 x 2 64127e 11 y 7 16872e 12 y x 3 16406e 11 yx 1 70420e 11 x V3 485 444 0 0252266 y 0 00126324 x 1 94016e 7 y 5 16536e 8 yx 6 76348e 9 x 23 5 50252e 11 y 2 8479 1e 11 yx 1 91024e 11 yx 3 46178e 12 x SBC V2 176 69 0 00166 y 0 03376 x 0 187e 7 y 3 25e 7 yx 1 07e 7 x 4 53e 11 y 2 901e 11 y x 3 720e 11 yx 8 315e 11 x V3 485 442 0 03015 y 0 00139 x 31 99e 8 y 7 54e 8 yx 1 83e 8 x 6 284e 11 y 1 444e 11 y x 4 0e 11 yx 9 757e 11 x In the above equations x and y are the distances in detector pixels from the center of the camera x y 0 0 at the center of the camera In the WFC the camera center is between the two chips note that Tiny Tim assumes that both detectors are perfectly adjacent to one another in reality there is about a 50 pixel gap between them and they are slightly rotated relative to each other The resulting V2 and V3 values from these equations are in arcseconds on the sky in the HST coordinate system See the diagram below for mappings from detector X Y to V2 V3 The coordinates on the sky i
4. 022 11 4 f 48 48 0 045 22 9 For 512 x 512 pixel mode unzoomed The addition of COSTAR altered the optical characteristics of the FOC FOC with COSTAR Optical Parameters Focal Pixel Size Field Size Camera Ratio arcsec arcsec 96 151 0 014 7 3 f 48 72 5 0 030 15 2 l For 512 x 512 pixel mode unzoomed Tiny Tim Queries Specific to FOC e Date of observation pre COSTAR used to compute the focus and aberration values which are time dependent Image Sizes The FOC has selectable image sizes of 512 x 512 pixels or 512 x 1024 In the latter mode the dynamic range is only 8 bits 256 levels One dimension of a pixel can be stretched by a factor of two zoomed mode Tiny Tim only models the 512 x 512 modes using the optical parameters listed in the tables above Distortion and Field Dependent Aberrations The images produced by the FOC are highly distorted due to the nature of the photon counting detectors Most of the distortion is corrected in the calibrated data but near the field edges it is still fairly high One should only assume that the central 256 x 256 region is well corrected Tiny Tim assumes that there is no distortion There is also some field dependence of the aberrations but they are small and not well characterized and thus are not included in Tiny Tim FOC models Filters The available FOC filters in Tiny Tim are f 48 FIZ0LP F140W FI50W F175W F180LP F195W F220W F275W F305LP 27 f 96
5. 1 WFPC2 NICMOS and ACS the other files will have successive numbers nicmospsf01 fits nicmospsf02 fits Note that when modeling the ACS the PSFs produced by tiny2 have a _psf fits extension e g acs00_psf fits These PSFs are intended for use by tiny3 and not the user Then the PSFs produced by finy3 will have normal Tiny Tim filenames e g acs00 fits An Example Run As an example let s generate a WF PC 1 WFC2 PSF in F555W at different positions on the detector User input is in bold italics tinyl wfpcl in TRARA Tiny Tim v6 0 The HST PSF Generator Developed by John Krist krist stsci edu Additional support by Richard Hook rhook eso org http www stsci edu software tinytim html SOA Aberrated Cameras mae Corrected HST Optics Hass Wide Field Camera WFPC1 f 12 9 5 WFPC2 Wide Field Camera f 12 9 2 Planetary Camera WFPC1 f 30 0 6 WFPC2 Planetary Camera f 28 3 3 FOC 48 7 COSTAR corrected FOC 48 f 72 5 4 FOC 96 8 COSTAR corrected FOC 96 f 151 Gecond Generation 385566 Third Generation 9 NICMOS Camera 1 f 80 15 ACS Wide Field Channel f 26 0 NICMOS Camera 2 f 45 16 ACS High Resolution Channel f 72 1 NICMOS Camera 3 f 17 2 17 ACS HRC Coronagraph off spot PSF 2 STIS CCD f 36 18 ACS Solar Blind Channel f 72 3 STIS NUV MAMA f 90 4 STIS FUV MAMA f 90 Choice 1 Enter
6. F120M F130M FI40M F152M Fl65W F170M FI75M F190M F195M F210M F220W F231M F253M F275W F278M F307M F320W F342W F346M F370LP F372M F410M F430W F437M F470M F480LP F486N F501N F502N F550M F600M F630M The F320W filter appears to significantly degrade the PSF for unknown reasons This degradation is not modeled by Tiny Tim Caveats Since the FOC typically operates at short wavelengths it is very sensitive to the aberrations in the telescope especially the mirror zonal errors which cause the PSF to change dramatically with wavelength as shown above Uncertainties in the zonal errors and other aberrations will result in mismatches between the model and observed PSFs especially in the wings of the aberrated images As with WF PC 1 the aberrated FOC PSFs were very sensitive to focus and other aberration changes 28 WF PC 1 The first Wide Field Planetary Camera WF PC 1 was an eight channel instrument four wide field cameras WFC 1 4 or four planetary cameras PC 5 8 with either set selected using a rotating pyramid mirror WE PC 1 Optical Parameters Focal Pixel Size Field Size Camera Ratio arcsec arcsec WFC 1 4 12 9 0 1 76 PC 5 8 30 0 0 043 33 Tiny1 Queries Specific to WF PC 1 e Camera either 1 4 for the WFCs or 5 8 for the PCs e Position on the detector used to compute the obscuration pattern the name of a file containing up to 100 coordinate pairs can be entered preceded by a
7. FISOLP F165LP Some of these filters are only available with the HRC 22 CCD Charge Diffusion The ACS CCDs like all CCDs suffer to some extent from charge diffusion This is where some electrons photogenerated within a pixel travel into adjacent pixels before being detected This causes a slight blurring For a more in depth description see the sections on WFPC2 and STIS Tests on ACS like CCDs have been done to derive the blurring properties and how charge diffusion varies with wavelength Tiny Tim approximates charge diffusion by convolving normally sampled ACS WFC or HRC PSFs with a 3 x 3 pixel kernel appropriate for the wavelength It does not apply the kernel to subsampled PSFs which must be manually convolved by the user after rebinning the image to normal sampling The appropriate kernel is provided in the FITS file header produced by tiny3 ACS HRC Red Halo The ACS HRC chip has a defect that creates a halo surrounding the PSF at wavelengths gt 0 6 um The relative proportion of flux within this halo increases with wavelength The halo is large many arcseconds and can contain 10 20 of the total flux It is caused by the CCD becoming transparent to long wavelength photons allowing red light to pass through into the glass backing bounce around and bounce back into the substrate The WFC CCDs have a metallized backing that prevents such halo formation An estimate of the halo is added to all HRC PSFs for wavelengths gt 0
8. convolved geometrically distorted scene is written out to a FITS file To use the scene processing capability of tiny3 you must provide an optional parameter file A template version of this file is produced by finy2 with the tt3 extension The format of this file looks something like this INPUT_FILENAME no_file PIXEL SCALE 0 02133 X_CENTER 512 Y_CENTER 512 OUTPUT_FILENAME no_file The five keywords shown must be present in any optional parameter file The default no_file values indicate that no scene generation is done The meaning of these keywords are INPUT_FILENAME The full name including extension of a FITS image file that contains the undistorted input scene The FITS file MUST be in the standard 4 byte IEEE single precision floating point format scaled integer FITS files are not supported As described later in this section this entry may be used to specify a blank input field rather than an input image Example use INPUT_FILENAME galaxy_field fits PIXEL _ SCALE The scale in arcseconds per pixel of the image specified by INPUT_FILENAME By default this is set to the scale of the PSF produced by tiny2 The user must set this entry to the appropriate value for the input image The image will be resampled via damped sinc interpolation onto a grid with the same sampling as the tiny2 PSF so the input scene should not be so coarsely sampled that significant
9. determining peak pixel values relative to total PSF flux predicting the width of the PSF core at a given wavelength e Photometry PSF profile fitting by the shifting and scaling of models testing completeness by generating synthetic images e Algorithm testing photometric and deconvolution procedure testing e PSF subtraction e Data modeling convolution of model data with model PSFs to simulate observed images Caveats Model PSFs do have significant limitations though some of these are shared with observed PSFs as well The simulation is only as good as the input parameters which are often inaccurate due to our limited knowledge of the actual time varying optical system A large number of factors affect the PSF including e Filter optical and detector responses with wavelength e Object spectrum e Focus time and position dependent e Aberrations which are generally time focus and position dependent e Polishing errors in the mirrors e Obscuration positions field dependent and sizes focus dependent e Detector orientations rotation pixel sizes e Detector subpixel responses e Geometric distortions e Scattering by dust scratches chips rough surfaces e Scattering by the detector Many of these vary with time and or field position so that it is impossible to create a model that will match an observed PSF pixel for pixel Of course even observed PSFs will often have significant differences due to these same variati
10. that tiny3 will only process one PSF at a time Generating ACS PSFs ACS is located away from the optical axis of HST and so it suffers from significant distortion that is not corrected by the camera s internal optics The projection of the camera s field of view onto the sky looks like a sheared rectangle the distance along one diagonal is greater than the other Because of this effect it is not sufficient for Tiny Tim to generate undistorted PSFs for the ACS like it does for the other cameras In addition while distorting PSFs it makes sense to include the capability to PSF convolve and distort an arbitrary input image to simulate an ACS observation To handle the additional tasks the following changes have been made to the usual Tiny Tim procedures tiny1 will not ask if you want to generate a subsampled PSF that is handled by the SUB x command line keyword parameter to tiny3 see below tiny2 no longer produces the final PSF that is left to tiny3 The PSF produced by tiny2 is sampled 1 3 times better than the Nyquist sampling for the shortest wavelength in the specified basspand This allows for better interpolation results in finy3 This PSF is not geometrically distorted It is intended strictly for use by finy3 and not by the user The tiny2 PSF will have a _psf fits extension with filenames like psf00_psf fits psf01_psf fits etc depending on how many multiple positions you choose to simulate 21 tiny2 will cre
11. the WFPC repeater cameras secondaries and spiders and any vignetting which occurs from other sources like the WFC entrance aperture Optical aberrations manifest themselves as errors in the optical path length For HST these include spherical aberration defocus coma astigmatism clover and mirror zonal aberrations along with others These properties can be simulated on a computer by creating a two dimensional array which contains the aperture function basically a mask which shows where the beam is not being obscured and another array containing the optical path differences OPD function The aperture function depends on which camera is being used and if it is WFPC the shifts caused by the repeater camera obscurations must also be taken into account The OPD can be calculated as the sum of Zernike polynomials which describe specific aberrations and additional terms such as local errors in the mirrors surfaces A list of Zernike polynomials is included in the HST OTA Handbook These two functions are generated for each point on a grid of Nx 2 by Ny 2 where Nx and Ny are the dimensions of the arrays This provides for critical sampling of the functions Since Tiny Tim uses square arrays the functions are defined only for the central N 2 by N 2 region The array size depends on how large a PSF is needed The OPD and aperture function A form the complex pupil function P Ae TORDIM and the Fourier transform of the pupil functio
12. they fell causing a slight blurring of the image This is due to charge diffusion which is described in more detail in the WFPC2 section Tests for the ACS project on CCDs like that used in STIS have provided good measures of the charge diffusion at different wavelengths Tiny Tim approximates the blurring caused by this phenomenon by convolving the PSF with a 3 x 3 pixel kernel appropriate for a given wavelength This is only done for normally sampled PSFs Subsampled PSFs should be manually convolved with the kernel AFTER the PSF is rebinned to normal sampling by the user The appropriate kernel is provided in the FITS header for PSFs produced by tiny2 19 Defocus Both the CCD and MAMA imaging modes are slightly out of focus because the instrument is optimized for spectrographic work The amount of defocus is equal to about 4 3 um of breathing and is included by Tiny Tim In addition there is an additional 1 5 microns equivalent defocus caused by non parfocality with the WFPC2 PC detector which is assumed to always be at best focus Caveats The CCD mode includes a Lyot stop Because the stop is not located exactly in a plane conjugate to the exit pupil its location relative to the OTA pupil appears to shift with field position Tiny Tim assumes that the stop does not shift and is always at the position appropriate for the center of the field the mask is slightly misaligned at this location and this is accounted for by Tiny Tim Tin
13. use the SYNPHOT calcspec routine like so to write the spectrum to the file my_spectrum tab calcspec bb 5000 my_spectrum form photlam Note that the output here is in photlam photons cm sec Angstrom calcspec uses Angstroms for the wavelength If the default wavelength range used by calcspec doesn t cover the range of your filter you may need to provide a wavelength file using the wavetab keyword see the SYNPHOT manual for more information To convert the STSDAS tab table file to an ASCH file use the STSDAS t dump command tdump my spectrum tab gt my_spectrum txt Then you have to edit the beginning of the text file to get rid of the header lines and then put the form of the fluxes in this case PHOTLAM in the first line Tiny Tim will only read the first two columns of the spectrum and ignore any remaining ones The filename of your spectrum table is given to Tiny Tim using the spectrum keyword when running tinyl For example tinyl test in spectrum my_spectrum txt You can provide separate spectrum and filter tables if you wish Specifying Your Own Filter Table If for some reason Tiny Tim s default filter throughput tables are not sufficient you can provide your own To do so you must create a text file containing the wavelength in nanometers and corresponding transmission one pair per line in order of ascending wavelength A maximum of 200 wavelengths can be entered The wavelengths should be spaced by about 0 018
14. 6 um Field Dependent Aberrations The ACS notably the WFC will have significant field dependent aberrations focus coma astigmatism Tiny Tim includes these effects as predicted by optical ray trace models These aberrations vary slowly with field position so it should not be necessary to finely sample the entire field a few arcseconds or even more between positions is probably sufficient Geometric Distortion As described previously the geometric distortion in the ACS is significant The diffraction spikes in PSFs for instance will look clearly non perpendicular Tiny Tim includes geometric distortion effects in the processing done in finy3 The distortion relations used were derived from optical ray trace models which should be fairly good predictions of large scale distortions However there may be higher frequency distortions caused by the detector especially in the SBC that have not been included due to a lack of information The distortion coefficients are likely to change once on orbit measurements have been done tiny3 properly accounts for the varying pixel area so that the distorted PSF or scene properly represents the image on the detector before any compensation for pixel area that may occur during flat fielding The distortion relations used in Tiny Tim Version 6 0 are given below WFC V2 254 552 0 001912 y 0 049479 x 7 8968e 8 y 2 94333e 7 yx 3 99467e 7 x 3 9707 1e 12 y 2 42701e 11 y x
15. All three programs require at minimum a single command line argument the name of the parameter file For example tinyl test par tiny2 test par tiny3 test par tiny2 produces a FITS image file containing the PSF If you are modeling the ACS tiny3 will create a FITS file containing the geometrically distorted PSF or PSF convolved scene see the ACS section for more details Optional Command Line Parameters tiny1 allows the following optional command line parameters given after the parameter filename tiny3 also has additional command line parameters and those are listed in the ACS section ebmv x or Av x Interstellar extinction of x magnitudes is applied to the object spectrum specified in the form of E B V or visual extinction A Do not specify both filter filename The user can provide his own system throughput curve by providing an ASCII file which contains wavelength in nm and throughput pairs one per line This will be used instead of the default filter curves See Appendix C Object Spectra and Filter Curves jitter x Convolve the PSF with a Gaussian kernel approximating x milliarcseconds RMS of jitter spect rum filename The user can provide his own spectrum by providing an ASCII file which contains wavelength in Angstroms and flux pairs one per line See Appendix C Object Spectra and Filter Curves wmag x Increase or decrease by a factor of x the default number of wavelengths used in computing a polychro
16. Anm The object spectrum filter throughputs and detector response all go into computing the transmission The filename of your filter table is given to Tiny Tim using the filter keyword when running tinyl For example tinyl test in filter my_filter txt You can provide separate spectrum and filter tables if you wish 35
17. CD camera includes a coronagraph STIS was installed during the second servicing mission along with NICMOS STIS Optical Parameters Focal Pixel Size Field Size Camera Ratio arcsec arcsec CCD 35 5 0 05079 52 0 NUV MAMA 86 9 0 02474 25 3 FUV MAMA 86 9 0 02474 25 3 Filters Because it is primarily used as a spectrograph STIS has a limited filter set for imaging Note that both the CCD and MAMA cameras have clear apertures SOCCD or 25MAMA that do not include a filter CCD 50CCD F28X50LP F28X500H F28XS50OIII NUV MAMA 25MAMA F25CIII F25CN182 F25CN270 F25MGII F25QTZ F25SRF2 FUV MAMA 25MAMA F25LYA F25QTZ F25SRF2 Halos and Ghosts STIS CCD PSFs have a halo that becomes more prominent at longer wavelengths The CCD silicon substrate is mounted on glass and at wavelengths longer than 700 nm some photons can travel through the CCD and into the glass where they are back scattered into other pixels STIS NUV PSFs have an extended halo caused by charge diffusion in the MAMA detector it is not nearly as prominent in the FUV channel STIS halos are not currently included in Tiny Tim due to a lack of suitable information for characterizing them Optical ghosts are also present in CCD images These appear as circles positioned on a line between a star and the center of the detector These ghosts are not included by Tiny Tim Charge Diffusion Like all CCDs some photons may be detected in pixels adjacent to those in which
18. Chip 1 2 3 4 2 Next we ll be asked for the positions of the PSFs on the detector which must be integer numbers This question is only asked for WF PC 1 WFPC2 NICMOS and ACS Let s assume that we want to generate PSFs at three different locations on WFC2 We ll create a plain text file xy 1lis which lists the coordinates one pair per line like so up to 100 PSFs are allowed 100 100 400 400 700 700 We ll enter the filename preceeded by a for the position Enter position x amp y on detector in INTEGER pixels range 0 799 or the filename of a list of positions preceded by a ie xy lis Position on detector xy lis Now tinyl is going to ask for the date of observation It only asks for the date for WF PC 1 the pre COSTAR FOC and NICMOS Enter the date of observation in the form dd mm yy For example 6 April 1991 would be 6 4 1991 Date 441992 Date is April 4 1992 We are now asked for the filter We could say mono if we wanted to generate a purely monochromatic PSF If we had provided our own filter throughput table using the filter x option on the command line we would not be asked this question In this example we ll just use the filter information which is in the Tiny Tim database Select filter passband Enter the name of the filter eg 555w Enter MONO to specify a single wavelength Choice f555w If we chose something other tha
19. The Tiny Tim User s Guide Version 6 0 July 2001 http www stsci edu software tinytim John Krist krist stsci edu Richard Hook rhook eso org Changes in Tiny Tim Version 6 0 General Tiny Tim now writes out only FITS files and these files have fits extensions Log files are no longer produced as the FITS header now contains the PSF information A new interpolation method damped sinc is now used which is faster than the old way adaptive sinc This can increase Tiny Tim s speed by up to a factor of 7 for large PSFs User defined spectrum files must now begin with a keyword indicating the units of the flux column PHOTLAM FNU FLAM JY Any fluxes in these units will be converted into the internal form used by Tiny Tim Power laws are now available for specifying the object spectrum STIS The default focus offset for the imaging modes has been updated based on phase retrieval analysis ACS Advanced Camera for Surveys Many significant changes have been made to support the ACS including field dependent aberrations derived from ray trace analysis HRC CCD red halo HRC off spot coronagraphic PSFs geometric distortion user defined scene PSF convolution and distortion A new program tiny3 has been added specifically to process ACS PSFs and simulated scenes This new program is documented in the ACS section of this manual Contents Updates to Version 6 0 2 Contents 3 Introduction 4 Uses of Mod
20. ate a template optional parameter file that can be used by tiny3 to generate a PSF convolved geometrically distorted scene this file has the same rootname as the tiny amp tiny2 parameter file with a tt 3 extension See the section below on scene generation for proper use of this facility tiny3 is specifically used for ACS PSF simulation you cannot use it for other HST cameras It reads in the PSF produced by tiny2 and integrates it onto distorted pixels on a distorted grid The tiny3 command line is tiny3 parameter_file foptional_parameter_file SUB x POS n where parameter_file is the same filename given on the tiny1 and tiny2 command lines and optional_parameter_file optional The name of a text file containing additional parameters used for scene generation A template file is produced by tiny2 with the tt3 extension See the section on scene generation below for more details about this file If this parameter file is specified it must be the second parameter on the command line SUB x optional Specifies the desired subsampling factor of the final PSF The specified value must be an integer between 1 and 10 The final PSF will have pixel dimensions 1 x of normal in each direction Subsampling beyond a factor of 5 is probably useless in that case you may be better off interpolating from a 5x subsampled PSF NOTE The HRC and WFC CCD charge diffusion kernels are not applied to subsampled PSFs but they are provided in t
21. d spherical aberration These have been measured from on orbit images using phase retrieval techniques These vary slightly with focus but over the focus range of science observations these changes are insignificant They also vary with time as the optical alignment of the NICMOS system changes dewar expansion FOM mirror position changes These variations have been documented by Suchkov et al 1999 and Krist 1999a Tiny Tim uses the Suchkov et al aberration time relations for cameras and 3 and the Krist relations for camera 2 16 Focus coma and astigmatism also vary with field position In cameras 1 and 2 focus varies linearly across the field while in camera 3 it varies quadratically with the best focus at the center These variations have been measured using phase retrieval and verified by encircled energies Camera 2 has the largest change in focus across the field on the order of 1 5 mm equivalent PAM space defocus or about 15 um of breathing The changes in coma and astigmatism are fairly small in cameras 1 and 2 but are more significant in camera 3 due to its larger field Tiny Tim asks the user for the position of the PSF on the detector and from that determines the field dependent aberrations Pixel Scale Measurements of the separation of stars in a cluster have shown that the plate scale changed as the dewar expanded and contracted However other measurements of NICMOS 2 PSFs indicated that the effective plate scale of
22. e are the dimensions of the field in arcseconds For example to create a 4 5 by 4 5 arcsecond field and then add a few PSFs of various intensities you could use something like the following INPUT_FILENAME blank_4 5_4 5 PIXEL _SCALE 0 0 X_CENTER 512 Y_CENTER 512 OUTPUT_FILENAME psfs fits PSF 0 0 0 0 1500 0 PSF 1 5 1 5 1000 0 PSF 1 5 1 5 2000 0 PSF 1 5 1 5 3000 0 PSF 1 5 1 5 4000 0 The value of the PIXEL_SCALE entry is ignored but must still be present when the blank field option is used You should not try to create a single 4K by 2K WFC image by using a single PSF and a large input scene The scene processing facility is meant to be used on small regions that the user will manually mosaic into a full image Thus you should attempt to include overlapping regions in your input scene 26 FOC The Faint Object Camera is the only remaining first generation science instrument left in HST It is optimized for UV studies with a wavelength range of 100 500 nm It is now corrected for spherical aberration in the telescope by COSTAR Corrective Optics Space Telescope Axial Replacement The FOC consists of two separate detectors commonly referred to as the f 96 and f 48 channels Due to previous electronics problems the f 48 channel is rarely used FOC Pre COSTAR Optical Parameters Focal Pixel Size Field Size Camera Ratio arcsec arcsec 96 96 0
23. el PSFs Caveats Installation 5 Multithreading Running Tiny Tim 7 Optional Command Line Parameters General Input Parameters Output Files An Example Run General PSF Properties 12 Focus Changes Breathing and Desorption Wavelength Camera Specifics 13 WFPC2 12 NICMOS 16 STIS 19 ACS 21 FOC 27 WF PC 1 29 Appendix A 31 References Appendix B 32 How PSFs Are Simulated Appendix C 34 Object Spectra and Filter Curves Introduction Tiny Tim is a software package for generating Hubble Space Telescope HST model point spread functions PSFs It is easy to use and relatively fast It is written in standard C and thus is portable to a variety of computers and operating systems including UNIX Linux and Windows For details on how PSFs are generated please see Appendix B For the most up to date information on Tiny Tim as well as example applications of PSF models and the FAQ list check out http www stsci edu software tinytim Tiny Tim is a personal endeavour of John Krist with additions by Richard Hook initial NICMOS support and user defined filter tables The Space Telescope Science Institute which is the distribution point for Tiny Tim is not responsible for the software Any questions or comments however may be sent to krist stsci edu Uses of Model PSFs Besides optical analysis and deconvolution model PSFs have been used for a wide variety of applications e Proposal planning
24. ere it was generated even into an adjacent pixel hence the term charge diffusion The net effect is blurring of the image as some photons hitting within one pixel are detected in another Since this causes a dependence on where in the pixel the photon hit it is characterized by the subpixel response function The amount of charge diffusion varies with wavelength Shorter wavelength photons are converted to electrons near the illuminated surface of the detector while it typically requires a longer path for long wavelength photons very long wavelength light can actually pass through the substrate without being detected In backside illuminated CCDs like in WF PC 1 STIS and the upcoming Advanced Camera the electrodes are on the rear side of the detector closer to where long wavelength photons are converted Thus in such devices charge diffusion becomes worse with decreasing wavelength For front side illuminated CCDs like those used in WFPC2 the opposite is not true Charge diffusion is high at longer wavelengths gt 800nm but also at shorter ones lt 400 nm since the short wavelength photons are scattered by the electrode structure on the illuminated surface Charge diffusion is minimal but not insignificant at about 550 nm Charge diffusion in WFPC2 slightly blurs the images producing an effect similar to jitter In the PC it is equivalent to about 14 mas of jitter while in the WFCs because they largely undersampled the PSF t
25. errations and obscuration patterns Focus amp Aberrations The NICMOS dewar began expanding when the instrument was placed in the telescope due to expansion of the nitrogen coolant The dewar later began to contract but it has not returned to its original state This has placed the focus of camera 3 outside of the range of the Pupil Alignment Mechanism PAM which internally adjusts the NICMOS focus Cameras 1 and 2 are also no longer confocal but are well within the PAM range The focus of an observation ignoring breathing is dependent on the PAM position at the time the image is taken relative to the position of best focus Because each camera has a different focus the PAM is moved to the best focus position for either camera 1 or 2 depending on which is the primary instrument To bring camera 3 into focus there were two campaigns during January and June 1998 in which the telescope s secondary mirror was moved Otherwise camera 3 is out of focus and typically not used Tiny Tim includes a table of focus values for the time span of the first life of NICMOS and determines the proper focus for the date entered by the user including the NICMOS 3 campaigns The focus can also be computed from the PAM position if the user enters pam instead of the date after which it will ask for the date to determine the other aberrations In addition to focus other aberrations have some effect on the NICMOS PSF notably astigmatism coma an
26. he effect is more like 40 mas The wavelength dependence of the subpixel response function has not been characterized except in limited laboratory tests Tiny Tim approximates the effects of charge diffusion by convolving the normally sampled WFPC2 PSF by a Gaussian kernel of 3 x 3 pixels This kernel is most appropriate in the range of 500 600 nm but since nothing better is available it is used at all wavelengths Because this effect occurs at the pixel level this charge diffusion kernel is not applied to subsampled PSFs You must apply the kernel after rebinning the subsampled PSF to normal sampling Ideally a subsampled subpixel response function would be convolved with a subsampled PSF and then sampled to get a PSF at the correct pixel phase but this process is not practical for most uses of the models The kernel used by Tiny Tim for WFPC2 is 0 0125 0 05 0 0125 0 0500 0 75 0 0500 0 0125 0 05 0 0125 A recent paper Lauer 1999 describes in further detail the subpixel response of WFPC2 14 Filters WFPC2 has a wide variety of narrow medium and wide band filters It also has quadrant filters like methane and redshifted O II and polarizers In some modes the polarizers and the Woods filters FI60AW and F160BW vignette part of the field effects that are not included in Tiny Tim There are also linear ramp filters which are not explicitly included in Tiny Tim but can be modeled by generating a monochromatic PSF of the appropria
27. he FITS header so that the user can convolve the PSF with them after rebinning the PSF to normal sampling note that the kernel is wavelength dependent POS n optional Specifies which PSF to geometrically distort if PSFs at multiple positions were generated in a single run By default tiny3 will only process the first position n is an integer between 1 and the number of positions When generating a scene rather than a PSF with tiny3 the SUB and POS keywords are ignored The filenames of the PSFs produced by tiny3 have fits extensions e g acs00 fits acs01 fits etc Coronagraphic Off Spot PSFs The ACS HRC has a coronagraphic mode with occulting spots and a Lyot stop While Tiny Tim does not simulate observations of targets behind an occulting spot it does simulate field PSFs for objects outside of the spot The off spot PSFs are different from the regular HRC PSFs because of the Lyot stop All of the other characteristics of the HRC are included however filters distortion etc Filters The ACS includes a set of WFPC2 and Sloan Digital Sky Survey broadband filters and a limited selection of narrowband filters It does have ramp filters which are not included in the Tiny Tim database use a monochromatic PSF of the appropriate wavelength for these WFC amp HRC F220W F250W F330W F344N F435W F475W F502N F550M F555W F606W F625W F658N F660N F775 W F814W F850LP F892N SBC F115LP F122M F125LP F140LP
28. he WFCs are then slightly out of focus with the worst WFC3 having a defocus equivalent to about 9 um of breathing Tiny Tim accounts for both obscuration shifting and aberration variations with field position using the coordinates entered by the user Geometrical distortion is not included The focus offsets between the cameras are included with the PC assumed to be at perfect focus 13 Large Angle Scattering Some of the light from the target will be scattered by the CCD surface and reflected back by the optics distributing flux further out into the wings Tiny Tim does not include this effect so the PSF models will underestimate the flux in the wings The scattering is not uniform but rather consists of streaks and rays radiating from the core These change intensity and position with the location of the object on the detector further adding to the residuals one can expect when subtracting models from observed PSFs Subpixel Response Function All CCDs suffer from an effect called charge diffusion CCD pixels are not physically separate elements they are defined by the electromagnetic fields created by the electrode structure on the detector surface Thus pixel edges are actually vague When a photon is converted to an electron in the substrate the electron tends to be attracted to the nearest electrode But in regions where the field strength is weak i e furthest from the electrode an electron may travel some distance from wh
29. ings and central obscuration shadows in the PSFs to vary which could lead to significant residuals in deconvolutions For these instruments Tiny Tim has a database of dates of mirror moves and the measured focus values for those times Using a date provided by the user the information in this database and the power law describing desorption the proper focus for that time is computed excluding breathing For the corrected cameras except NICMOS WFPC2 FOC COSTAR STIS ACS time dependent focus is not included so you are not asked for a date The PC in WFPC2 is assumed to be in perfect focus at the center of the field as is FOC COSTAR and the ACS In NICMOS focus is computed based on the PAM Pupil Alignment Mechanism positions of the observation and of best focus for the camera In all cases adjustments to focus to simulate breathing for instance can be made by editing the file produced by tiny1 Towards the end of that file is a list of aberrations one of which is focus These values are in RMS waves of the aberration at 547 nm To simulate breathing 0 011 should be added or subtracted to the current value for each micron of secondary mirror despace subtracting means that the secondary moved towards the primary Wavelength The largest variations in the PSFs occur with wavelength As wavelength increases the diffraction structures rings spiders expand proportionally In wide band filters the expansion of the PSF over the band
30. interpolation artifacts may occur The input image should also not be so large that it exceeds the limits of the largest available grid 4K x 4K when resampled to the scale of the input PSF otherwise the edges of the field will be truncated 25 X_CENTER Y_CENTER The corresponding location on the detector in pixels of the scene image center Note that the first pixel on the detector is 0 0 If you generated PSFs at multiple positions then tiny3 will use the PSF closest to this position OUTPUT_FILENAME This is the name of the FITS file that will contain the PSF convolved geometrically distorted version of the input scene You should provide the extension tiny3 can also add PSFs of specified fluxes to the scene at specified locations This facility should be used rather than attempting to add PSFs by having delta functions in the input scene which would probably be distorted by the resampling step To add a PSF include the following line in the optional parameter file PSF x_position y_position counts where x_position and y_position are offsets from the scene center in arcseconds and counts is the total counts in the PSF Multiple PSF lines can be included in a single optional parameter file You can also create a scene with just PSFs by using the blank field option for the INPUT_FILENAME and using multiple PSF entries To create a blank field enter blank_xsize_ysize as the INPUT_FILENAME where xsize and ysiz
31. ld NEVER be normalized based on the spider intensities whether using observed or model PSFs 15 NICMOS NICMOS Near Infrared Camera and Multi Object Spectrometer is optimized for imaging in the wavelength range of 0 9 2 5 um It consists of three separate cameras whose characteristics are listed in the table below Each has a 256 x 256 detector with 40 um pixels NICMOS Optical Parameters Focal Pixel Size Field Size Camera Ratio arcsec arcsec 1 80 0 043 11 0 2 45 0 076 19 55 3 17 2 0 2 51 2 Each pixel is essentially a separate detector there is no cross talk between elements So unlike WFPC2 there is no charge diffusion that would cause blurring at the pixel level There is a subpixel variation in response but it does not appear to significantly affect the imaging performance of cameras and 2 There have been reports of large Camera 3 photometric variations with position within a pixel see Lauer 1999 and Storrs et al 1999 Camera 2 has a coronagraphic mode that is not modeled by Tiny Tim Tiny1 Queries Specific to NICMOS e Location of the PSF on the detector used to compute field dependent aberrations the name of a file containing up to 100 coordinate pairs can be entered preceded by a and tiny2 will generate a PSF for each position with output filenames like test00 test01 e Date of observation or PAM position of the observation and of best focus used to compute time and focus dependent ab
32. ling is useful in deconvolution photometry and PSF subtraction By subsampling the PSF interpolating and then rebinning it the model can be registered to high precision especially important for highly undersampled cameras like the WFCs in WF PC 1 and WFPC2 When subsampling is used for WFPC2 STIS CCD or the ACS HRC WFC you need to manually convolve the PSF with a kernel after rebinning to normal sampling that simulates blurring caused by charge diffusion described in the sections on these respective cameras Note that the PSF is centered in the middle of a pixel whether that pixel is normally sampled or subsampled The center pixel is n 2 where n is the number of pixels along one edge of the final image beginning at 0 0 Jitter The pointing stability of the telescope in fine lock is typically better than 5 mas RMS In the first year or so the pointing was worse 15 mas Typically any value under 7 mas is not noticeable For most cases you should not add any If you want jitter you can specify the amount on the tiny command line like so tinyl test in jitter 7 where the amount of jitter is given in milliarcseconds RMS Gaussian Output Files The model PSF will be written to a FITS image file by tiny2 If you generated just one PSF the file name will have the rootname you specified in tiny with 00 appended e g nicmospsf00 fits If you generated PSFs for more than one position an option available for WF PC
33. matic PSF ie wmag 0 5 would use only half the default number of wavelengths while wmag 2 would double the number more finely sampling the response curve Increasing wmag provides a somewhat smoother PSF at radii beyond about 3 A minimum of one wavelength will be used For example tinyl test par ebmv 1 4 jitter 15 0 General Input Parameters A number of the questions which tiny asks are common to all of the instruments and are discussed here Inputs specific to each camera are listed in later sections PSF Size tinyl asks you for the diameter of the PSF you wish to generate in arcseconds From this it determines the proper grid sizes to use The maximum possible size of a model PSF is limited by the array dimensions used to compute the Nyquist sampled PSF At short wavelengths it may not be possible to compute a PSF larger than 7 Generally the models are not very good past a radius of 2 due to the effects of scatter and high frequency aberrations Generating a large PSF when you really only need a smaller PSF will simply waste computer cycles Note that tiny1 suggests a minimum good PSF size If the camera has PSFs with halos ACS HRC or F1042M filter halo in WFPC2 then you should use at least this minimum diameter Filters Wavelengths Spectrum You have the option of generating a purely monochromatic PSF or one that includes wavelength variations over a filter s bandpass Monochromatic PSFs are suitable for modeli
34. n a narrowband filter which has only one wavelength and did not choose the MONO option then we must select an object spectrum You can choose from a list of 17 spectra ranging from O to M type stars use a blackbody or power law spectrum or provide your own spectrum see Appendix C Object Spectra and Filter Curves In this example we ll choose one of the provided spectra Choose form of object spectrum 1 Select a spectrum from list 2 Blackbody 3 Power law F nu nu i 4 Power law F lambda lambda i 5 Read user provided spectrum from ASCII table Choice 1 A list of the available spectra along with their color terms are displayed and we choose one of them Now we have to specify how large a PSF to generate The maximum size depends on the wavelength and focal ratio of the camera In this case we want to generate a 6 arcsecond diameter PSF actually the closest we can get to 6 given the finite size of the detector pixels Assuming detector pixel size of 0 09993 arcsec and f ratio of 12 9 The maximum computable PSF size is 15 00 arcsec The recommended size is about 6 0 arcseconds What diameter should your PSF be in arcseconds 6 0 We want normal sampling in this case Do you wish to generate a subsampled PSF Y N n We want the rootname of the output FITS files to be wfpc1 10 Rootname of PSF image files no extension wfpcl To execute the next stage enter the command ti
35. n is the amplitude spread function ASF Finally the modulus squared of the ASF is the PSF PSF FFT P This is the Nyquist sampled PSF for a specific wavelength in which the OPD is defined with the spacing between pixels being FA 2 where F is the focal ratio of the instrument such as 12 9 for the Wide Field Camera Thus the sizes of the arrays used to generate the critical PSF are dependent on the required size of the integrated PSF and the wavelength Shorter wavelengths require larger grid sizes and thus more time to compute The Nyquist sampled PSF is then Fourier transformed to produce the optical transfer function OTF If jitter is specified the OTF is multiplied by a function that models Gaussian jitter Integration onto detector pixels is performed by multiplying the OTF by the analytical expression for the integrated detector OTF The result is then Fourier transformed back and the integrated values sampled using damped sinc interpolation 32 Because the PSF changes with wavelength a number of PSFs have to be generated by the above method at wavelengths which sample the filter being used to account for the filter s bandpass The monochromatic models are combined via a weighted addition The weights are dependent on the optical system throughput including the filter and the object spectrum 33 Appendix C Object Spectra and Filter Curves Because the size and shape of the HST PSF is dictated by diffraction
36. n the V2 V3 system of the corners of the distorted PSF s center pixel are given in the FITS header and can be used to determine the pixel scale V3 A ie 500 ay HRC SBC 400 x TTT WFC2 a WFC1 200 Vy 100 v2 500 400 300 200 100 p Above The mapping of ACS camera field of views on the HST focal plane looking at the sky The detector X Y axis directions are indicated V2 and V3 are shown in arcseconds relative to the OTA center Note that each WFC has X Y 0 0 at the first pixel of the detector From the ACS Instrument Handbook Version 1 0 24 Scene Generation Since tiny3 already makes use of the PSF and can do accurate geometric distortion it made sense to incorporate the capability to take an arbitrary input scene convolve it with the PSF and then distort it Tiny Tim uses the following procedure when processing scenes 1 The scene is read from the FITS file specified by the user The PSF produced by tiny2 is also read in 2 Ifthe input scene has a different pixel scale than the input PSF it is resampled onto a new grid using damped sinc interpolation to match the PSF scale The new grid has a maximum size of 4K by 4K pixels 3 The input scene is convolved with the PSF 4 The PSF convolved scene is mapped onto a distorted grid using damped sinc interpolation Each pixel in the distorted grid is divided into many subpixels to account for undersampling 5 The PSF
37. ng narrow band filters or the linear ramp filters in WFPC2 or ACS Tiny Tim has a database of wavelengths and weights for each filter A polychromatic PSF is created by generating monochromatic models at each wavelength and adding them together with the corresponding weights The wavelengths have been chosen to properly sample the filter s bandpass The throughput curve is multiplied by a spectrum to simulate the PSF variations caused by object color You can apply interstellar extinction using the ebmv x or Av x keyword parameter on the tiny command line See Appendix C Object Spectra and Filter Curves for more information You also have the option of providing a list of wavelengths and weights instead of using the default filter curves and spectra See Appendix C Object Spectra and Filter Curves for more information Sampling Model PSFs can be generated at an arbitrary sampling tinyl will ask if you would like to generate a subsampled PSF except for the ACS see the ACS section for details If you choose to do so it will ask you for the subsampling factor which is an integer from 1 to 10 e g 5 means that the resulting pixels are 1 5 of normal size in each dimension Subsampling generally increases the computation time by the square of the subsampling factor for a given PSF diameter If you are using high subsampling factors gt 5 then you may be better off subsampling by 5 for instance and then interpolating the result Subsamp
38. ny2 wfpcl in tiny will write out a file called wfpcl in We ll feed it to tiny2 tiny2 wfpcl in tiny2 will compute a PSF for each position in our list and write it out to a FITS file In this case the filenames will be wfpc100 fits wfpcl01 fits andwfpcl02 fits 11 General PSF Properties Focus Changes Breathing and Desorption The focus of the telescope varies within an orbit due to thermal effects which change the position of the HST secondary mirror by 1 10 um on average This is called breathing A long term focus change is caused by desorption of the telescope s graphite epoxy truss After being placed in orbit the structure began outgassing causing it to shrink and the focus to vary Initially the rate of desorption was great In order to remain at best focus the secondary mirror had to be moved away from the primary in order to compensate for the shrinkage These mirror moves occurred on a nearly monthly basis during the first two years of operation During these intervals however the focus continued to change in a predictable way exponential decay By the time of the first servicing mission the rate of desorption was low and mirror moves became less frequent Today a mirror move occurs roughly every six months Between these times the changes in focus due to breathing outweigh those caused by desorption In the aberrated cameras WF PC 1 and FOC without COSTAR breathing causes the positions of the tendrils r
39. ong pass filter or if your spectrum is reasonably matched by one of the default Tiny Tim spectra over the filter passband You must provide an ASCII text file which contains the wavelength in Angstroms and corresponding flux one pair per line up to 15000 pairs The first line of the file MUST be one of the following which tells Tiny Tim what units the fluxes are in FLAM FNU PHOTLAM or JY where these are defined as FLAM ergs Angstrom FNU ergs Hz PHOTLAM photons Angstrom JY Janskys W Hz The normalization of the fluxes is not important only the relative differences between wavelengths Your spectrum must not include camera system response effects these are handled when you specify the filter Tiny Tim will interpolate your spectrum to determine the flux for each component monochromatic PSF used to generate a polychromatic PSF Note that specifying the wavelength in Angstroms is a departure from the rest of Tiny Tim where wavelength is usually given in nanometers The wavelength range of your spectrum should cover the range of the filter you will be using and then some otherwise the spectrum will be extrapolated The beginning of a spectrum file might look something like this PHOTLAM 100 0 1 0e 3 120 0 1 3e 3 13000 Ls5e 3 34 You can generate an appropriate spectrum using SYNPHOT in STSDAS For example suppose you want to provide a 5000 K black body spectrum even though you can do it in Tiny Tim You can
40. ons Installation Compiling Tiny Tim Tiny Tim is available for download from the World Wide Web or via FTP To get it from the Web go to http www stsci edu software tinytim Using FTP go to ftp stsci edu and login anonymously then cd to software tinytim Tiny Tim is distributed in a compressed tar file as source code with supporting ASCII tables and FITS files This file should be downloaded in binary mode and then unpacked into a separate directory on your machine like so uncompress tinytimv60 tar Z tar xvf tinytimv60 tar After this the program needs to be compiled A Makefile is provided to automate this task with default compiler settings for Solaris Linux and HP versions of UNIX For other systems you should edit the Makefile and change the compiler settings for the OTHER mode as necessary The programs are compiled by running make using one of the following make sparcstation make linux make hp make other Setting Pointers to Tiny Tim The appropriate pointers to the Tiny Tim programs and directory must be included in your environment file cshrce profile or whatever is appropriate to the system shell The following shows a c shell example appropriate for users at STScI setenv TINYTIM usr stsci tinytim alias tinyl TINYTIM tinyl alias tiny2 TINYTIM tiny2 alias tiny3 TINYTIM tiny3 If you are running the Bash shell the default for most Linux installations you can follow this example for entries in y
41. our bash_profile file set the TINYTIM directory to whatever is appropriate for you TINYTIM usr local tinytim export TINYTIM alias tinyl STINYTIM tinyl alias tiny2 STINYTIM tiny2 alias tiny3 STINYTIM tiny3 Multithreading As of version 5 0 Tiny Tim supports multithreaded execution on multiprocessor systems that support POSIX threads Pthreads This includes Solaris 2 5 and later and certain distributions of Linux Red Hat 5 2 or later otherwise check http www uk linux org SMP title html for more info To compile Tiny Tim for multiprocessor systems use one of the following make commands make threadedlinux or make threadedsolaris Note to Linux users If you have a multiprocessor Linux system the kernel must be recompiled to support SMP symmetric multiprocessing to use more than one processor The default installation for Red Hat for instance has SMP disabled If you ordered a multiprocessor system with Linux installed it is probably already SMP enabled It is recommended that you run kernel 2 0 36 or later Running Tiny Tim Tiny Tim consists of three programs tiny tiny2 and tiny3 tinyl asks a series of basic questions and generates a parameter file that is read by tiny2 tiny2 does the actual PSF modeling requiring no additional input from the user tiny3 geometrically distorts ACS PSFs and input scenes it is only used for ACS modeling tiny2 and tiny3 can be run in batch mode if desired
42. pairs can be entered preceded by a and tiny2 will generate a PSF for each position with output filenames like test00 testOl Field Dependence and Aberrations Like WF PC 1 the obscurations in the repeaters spiders amp secondaries are not in a plane conjugate to the entrance pupil This causes the pupil pattern to vary with field position with the WFPC2 obscurations appearing to shift relative to the telescope s This creates significant variations in the PSF depending on where the object is imaged on the detector including changes in the shapes of the diffraction rings squishing of the core and alteration of the banding patterns in the diffraction spikes The rotation of the detector and obscurations are different for each camera so the PSFs are not interchangeable In addition to obscuration shifting some aberrations vary with field position These include focus coma and astigmatism Jon Holtzman NMSU has provided the field dependence relations for these aberrations Observed PSFs in the F1042M filter have a halo around them unique to that filter see Krist 1999 An empirical model of the halo is added to model PSFs Geometrical distortion has minor effects on the WFPC2 PSF as the pixel scale changes slightly towards the field edges It is greater in the WFCs than in the PC Each camera has a slightly different focus than the others Attempts are made to keep the PC in focus due to its higher resolution T
43. pass will blend diffraction rings creating smooth wings The PSF may even be slightly different due to color differences among objects in the same filter In narrow band filters though the diffraction rings are sharp and the bandpass is too narrow to show color effects As wavelength decreases the PSF becomes more sensitive to aberrations including zonal errors in the mirrors Thus a PSF in the UV will look completely different from one in the near IR 12 Camera Specifics WEFPC2 The second Wide Field and Planetary Camera WFPC2 is a replacement for WF PC 1 that corrects for the spherical aberration in the Hubble Space Telescope WF PC 1 had a rotating pyramid mirror that selected either four wide field or four planetary channels The pyramid in WFPC2 is fixed so only four channels are available three wide field cameras WFC and one planetary camera PC Each channel has a Cassegrain repeater system that has a three vane spider The CCDs are 800 x 800 element devices with 157 um pixels WFPC2 operates in the wavelength range of 150 1100 nm WEPC2 Optical Parameters Focal Pixel Size Field Size Camera Ratio Arcsec Arcsec PC1 28 3 0 0456 35 WF2 3 4 12 9 0 1 76 Tiny1 Queries Specific to WFPC2 e Camera either 1 for the PC or 2 4 for the WFCs e Position of PSF on the detector used to compute the proper obscuration function and determine field dependent aberrations the name of a file containing up to 100 coordinate
44. r some places where the models come up short Since wiggle is time dependent and apparently random it will lead to errors between the model and real PSFs since only a general offset for the cold mask is assumed These errors reveal themselves as mismatches in the banding patterns in the spiders changes in the shapes and intensities of the diffraction rings and variations in the widths of the PSF cores Unfortunately observed PSFs suffer from the same problems You can try to match the wiggle for a given observation by changing the mask x and y offset values in the parameter file produced by tinyl by 0 005 or so at most usually If models are being used for photometry by shifting and normalizing to fit the observed PSFs it may be necessary to tweak the focus to account for breathing or dewar changes See the earlier section General PSF Properties There are a number of electronics problems in NICMOS which produce features which may be mistaken for PSF structures The most noticeable one is called Stay Puft This is seen as an increase in signal in columns containing a bright feature like a well exposed PSF core 18 STIS STIS Space Telescope Imaging Spectrograph is a combined optical imager and spectrograph operating over the wavelength range of 120 1000 nm It consists of three separate cameras a 1024 CCD camera for visible light measurements and two 1024 MAMA detectors for far and near ultraviolet work The C
45. rather than seeing effects you must pay attention to how the PSF varies with wavelength As wavelength increases the diffraction structure rings spikes expand proportionally In the same broad band filter the PSF of a red star may be noticeably larger than that of a more blue one If you subtract a red object PSF from a blue object s you can end up with significant residuals this only applies to wide band filters the change over the bandpass of a narrow filter is far too small to be significant Since object color can make a difference you should try to match the object spectrum when you generate Tiny Tim PSFs in wide band filters Tiny Tim offers a selection of 17 different object colors O through M stars using selected spectra from the Bruzual Peterson Gunn Stryker spectrophotometric atlas One of these is likely to match your object s color in a given bandpass You can also specify a blackbody spectrum if that is appropriate With whatever spectrum option you choose including your own you can also apply standard interstellar extinction by using the ebmv or Av keyword when running finyl see Command Line Parameters on p 8 Specifying Your Own Spectrum If your object is so different that it cannot be reasonably well represented by one of the default spectra then you also have the option of providing Tiny Tim a spectrum to use instead You do not need to worry about this if you are using anything other than a wide band or l
46. ration Charge diffusion effects are not included in Tiny Tim WF PC 1 models Filters The following WF PC 1 filters are available in Tiny Tim F122M F157W F194W F230W F284W F336W F368M F375N F413M F437N F439W F469N F487N F492M F502N F517N F547M F555W F569W F588N F606W F622W F631N F648M F656N F658N F664N F673N F675W F702W F718M F725LP F785LP F791W F814W F850LP F875M F889N F1042M _ F1083N 29 Caveats WF PC 1 PSFs are highly dependent of field position due to the shifting obscuration patterns Also because the spherical aberration creates shadows of the spiders central obscuration and mirror support pads the PSFs are very sensitive to focus changes and optical distortions The focus for a given observation may need to be altered by adjusting the focus coefficient in the parameter file produced by tinyl as discussed previously 30 Appendix A References Additional information on HST PSFs can be obtained from the STScI web site www stsci edu including instrument science reports ISRs instrument handbooks and advisories Hasan H amp Burrows C J 1995 Telescope Image Modeling TIM P A S P 107 289 Krist J E 1999a Time dependence of the NICMOS 2 aberrations and obscuration pattern NICMOS ISR 99 011 Krist J E amp Burrows C J 1995 Phase retrieval analysis of pre and post repair Hubble Space Telescope images Applied Optics 34 4951 Krist J E amp Burrows C J 1994
47. te wavelength by selecting MONO when asked for the filter name The available WFPC2 filters in Tiny Tim are F122M F130LP F157W F160BW F165LP F170W F185W F218W F255W F300W F336W F343N F375N F380W F390N F410M F437N F439W F450W F467M F469N F487N F502N F547M F555W F569W F588N F606W F622W F631N F656N F658N F673N F675W F702W F785LP F791W F814W F850LP F953N F1042M FQUVNA FQUVNB FQUVNC FQUVND FQCH4NA FQCH4NB FQCH4NC FQCH4ND F1042M Halo Tiny Tim v5 0 and later now includes an approximation to a halo seen only in F1042M images see the WFPC2 Instrument Handbook This halo contains about 20 of the total flux Its cause is unknown but is likely due to the fact that the CCD essentially becomes transparent at such long wavelengths and light is scattered within the CCD backing The halo is not seen in any other filters Caveats One of the most popular uses of Tiny Tim WFPC2 PSF models is the subtraction of stars and stellar like galaxy cores in order to see faint material or companions which may be hiding under the PSF wings While the models can subtract much of the light significant residuals will be left behind Changing the focus may help some but the main problem is that scatter from the CCD surface is not modeled due to its very complex nature The banding patterns in the diffraction spikes do not match between the model and observed PSFs These bands are very sensitive to obscuration positions and sizes focus and wavelength PSFs shou
48. the 1997 1998 life of NICMOS the camera 2 mask shifted about 2 of the pupil radius relative to an average offset of 12 In addition the mask can wiggle about this offset by about 0 5 of the pupil radius within a day These changes cause variations in the shape of the diffraction rings and the positions of bands in the diffraction spikes of the PSF These can result in significant residuals in PSF subtractions see Krist et al 1998 for examples Cold mask shifts for cameras 1 and 2 were implemented in version 4 4 of Tiny Tim In version 5 0 long term changes in the position of the camera 2 mask are included General offsets are assumed for camera 1 Wiggle is not included since it varies with each observation Filters The available NICMOS filters are NICMOS 1 FO90M FO9SN FO97N FIO8N F110M F110W F113N F140W F145M F160W F164N F165M FI66N F170M F187N F190N POLOS POL120S POL240S NICMOS 2 F110W F160W F165M F171M F180M F187N F187W F190N F204M F205W F207M F212N F215N F216N F222M F237M POLOL POL120L POL240L NICMOS 3 F108N F110W F113N F150W F160W F164N FI66N F175W F187N F190N F196N F200N F212N F215N F222M F240M 17 Caveats Tiny Tim produces fairly good PSFs for NICMOS compared to the other cameras This is mainly due to the fact that in the infrared the PSF is less sensitive to aberrations which might not be known accurately by the modeling software There are howeve
49. the PSF defined as the radius of a given Airy ring has remained the same This reveals a distinction between the size of diffraction structure and the plate scale the separation on the detector of two objects at different field positions Cold Mask Shifting At the entrance to the dewar each camera has a pupil plane mask which is intended to block the relatively warm telescope structures spiders region outside of the primary mirror etc The masks for cameras 1 and 2 have additional tabs to cover the primary mirror support pads In camera 2 the mask also serves as the Lyot stop of the coronagraph The masks are cooled hence they are called cold masks Optimally the masks would be aligned with the telescope obscurations But analysis of on orbit PSFs Krist et al 1998 indicated that the masks are shifted producing an asymmetric pupil function These obscuration patterns have significant effects on the PSFs The roughly elliptical central obscuration creates elliptical diffraction rings and distributes more light into the wings reducing the peak pixel by 10 at 1 6 um in camera 2 The masks in cameras 1 and 2 are shifted by about 12 of the pupil radius and good estimates of the misalignments have been obtained There is currently insufficient data in camera 3 to determine if there is any shifting The position of the cold mask at least in camera 2 varies on both long monthly and short orbital timescales Krist et al 1999a During
50. y Tim does not model the CCD coronagraphic mode Because of the wide wavelength range a large number of monochromatic PSFs are generated to sample the CCD clear SOCCD and longpass F28X50LP filters 107 and 57 wavelengths respectively Thus it can take a while to generate a PSF 20 ACS NOTE Because of the significant distortion in the ACS the way Tiny Tim computes ACS PSFs is somewhat different than for the other cameras This includes the use of a third program tiny3 that does geometric distortion see below The ACS Advanced Camera for Surveys is set to be installed in HST during Servicing Mission 3B in late 2001 or early 2002 It is a multiple detector instrument with a wide field camera WFC consisting of two butted 2048 x 4096 CCDs 15 um pixel a high resolution HRC 1024 CCD 21 um pix and a STIS like 1024 MAMA 25 um pix for solar blind UV imaging SBC The HRC includes an aberrated beam coronagraph with separate occulting spots of 0 9 and 1 5 radii ACS Optical Parameters Focal Pixel Size Field Camera Ratio arcsec Width arcsec WFC 26 0 050 200 HRC 72 0 025 25 SBC 72 0 030 30 Tiny1 Queries Specific to ACS e Camera if the WFC you must choose detector 1 or 2 e Position of PSF on the detector used to compute the field dependent aberrations the name of a file containing up to 100 coordinate pairs can be entered preceded by a and tiny2 will generate a PSF for each position Note
Download Pdf Manuals
Related Search