Installation and Operating Instructions
Contents
1. C Il 2D Ex tD A21 IP67 T195 T130 T80 T 120 C The variant with integrated transformer is PTC protected no fuse replacement necessary Power supply AC or DC voltage depending on lamp fitted Caution Only alternating current should be used for luminaires with a built in transformer Warning Over voltage will cause premature lamp failure 10 voltage tolerance is admissible Please note Flash frequency if used as a flash lamp is lt 1 Hz e Parameters Temperature classification Type USL 05 Ex Built in Halogen lamp Ambient temperature range Type USL 05 Ex LED trans or LED illuminant Variant Volt former Voltage Socket 20 C lt T lt 40 C 20 C lt T lt 60 C o n e camzw 354003700 za without zavzow ca 2614 2013o 2673 201195 r cavmawl sseo0s600 22 without zavzow ca zoroena e avi zow aema 54003600 28 without zavzow ca cioc m o s 30vawieo 3540005900 2305 without zovawio ezo zere zorre F H Papenmeier GmbH amp Co KG division Lumiglas Talweg 2 58239 Schwerte GERMANY phone 49 2304 205 0 fax 49 2304 205 206 info lumi papenmeier de www lumiglas de PAPENMEIER lumiglas e Electrical connection Conditions requirements This Ex type luminaire has been manufactured with a permanently connected cable The free ends of this lead must be installed in a category 2G 2D enclosure if connection is to be carried out in a potent2. e Servicing Keep luminaire clean Keep note of average lamp life Use only original replacement parts F H Papenmeier GmbH amp Co KG division Lumiglas Talweg 2 58239 Schwerte GERMANY phone 49 2304 205 0 fax 49 2304 205 206 info lumi papenmeier de www lumiglas de
3. 2 Locking screw 3 Safety tab 4 Screw in glass lens e Mounting by way of hinged bracket The hinged bracket is used to secure the luminaire to the cover flange of a circular sight glass fitting also suitable for visual flow indicators Alternatively it can be attached to the slotted cover nut of screw type sight glass fittings to DIN 11851 The hinged bracket is fixed in place by turning the supplied M6 bolt into a blind hole which has previously been tapped in the pitch circle of the cover flange face An additional option is to weld on the bracket e Mounting by way of flanged adapter collar The flanged adapter collar is bolted or welded to the slotted cover nut DIN 11851 e Please note Fastening and mounting elements claw spanner etc should be ordered separately if needed e Replacement parts Part No Screw type lens light aperture with reflector 1774 022 00 Screw type lens light aperture without reflector 1774 030 00 O ring seal Viton 0862 036 00 Lamp socket G 4 2 pin 1202 011 00 Lamp socket GZ 10 1202 024 00 Cable entry gland complete with 2m connecting cable 1084 013 00 complete with 5 m connecting cable 1084 015 00 complete with 20 m connecting cable 1084 017 00 Halogen lamps LED illuminant 24 V 20 W G4 3232 206 00 24 V 20 W G4 reflector spot lamp 3232 222 00 12 V 20 W G4 3232 229 00 12 V 5 W G4 3232 221 00 230 V 4 W GZ10 LED 3232 004 00 e Accessories Claw spanner 6816 001 00
4. ially explosive environment The luminaire and the area around the installation site should be cleared of dust prior to installation and in the course of maintenance work The dismantled parts should be protected against dirt dust and contamination during installation or servicing work When closing the luminaire special attention should be paid to ensure that the interior of the lamp is free of dust The cable has already been connected inside the luminaire by the manufacturer and is ready for use The external protective terminal 1 must be connected to a separate operational earth The connecting cable should be secured after max 1 m Caution If the cable is being replaced e g by one of a different length the inner terminals need to be loosened before unscrewing the cable gland Replacing lamp Switch off power Allow sufficient time to cool down see type plate Undo locking screw 2 which releases the safety tab 3 for the screw type glass lens 4 Unscrew glass lens 4 using only the special claw spanner The defective lamp is then pulled out 2 pin type or removed with a press and twist movement GZ10 bayonet type Hold the new lamp bulb original products only please using a protective cloth taking care not to touch it with your bare fingers Carefully insert the replacement lamp push the 2 pin bulb into its socket or push and twist bayonet type lamps Make sure the lamp is securely in p
5. lumiglas Installation and Operating Instructions C oss Lumiglas luminaire type USL 05 Ex USL 05 Ex LED II 2G Ex d IIC T3 T4 T6 120 C II 2D Ex tD A21 IP67 T195 T130 T80 T120 C e Important please note Sight glass luminaires are specifically designed and solely intended for mounting with or onto flanged sight glass fittings Under no circumstances should a sight glass luminaire be used on its own as a lid or cover for vessel openings or as a substitute for the cover flange or the complete sight light port Luminaires for use in potentially explosive environments must be mounted installed and serviced by staff who have the relevant qualifications and have been properly trained for this type of work Please observe the data set out in the EC type examination certificate e General operating conditions Independent of pressure vacuum in the vessel Approved for use in Ex environments Gas Zones 1 and 2 Dust Zones 21 and 22 Approved for use in ambient temperatures between 20 C and 60 C or 40 C depending on the lamp fitted see type plate and temperature classification parameters Application as combined sight and light port on a sight glass fitting e Electrical data general acc to DIN 28120 mounting by way of hinged bracket Voltage power temperature class and protection rating are shown on the type plate Ex approval acc to EC type examination certificate BVS 08 ATEX E 133 Il 2G Ex d IIC T3 T4 T6 120
6. osition Before closing the luminaire re lubricate the thread of the screw lens e g with AEMA SOL 6 from A E Matthes Refit the glass lens 4 by screwing it into place until it is tight again pressure on O ring The glass lens 4 is locked into position once the safety locking tab 3 engages in one of the notches Retighten the locking screw 2 e Warning When replacing lamp bulbs make sure that the light beam is evenly distributed over the glass lens as prescribed by the design On no account should a hot spot be allowed to occur outside the luminaire caused e g by the incorrect position or condition of the lamp Mechanical installation The luminaire is attached to the cover flange of a circular sight glass fitting or visual flow indicator using the hinged bracket With the screw type sight glass fitting the luminaire is attached to the slotted cover nut alternatively it can be mounted using a hinged bracket or a flanged adapter collar e The Lumiglas luminaire Type USL 05 Ex is suitable for sight glasses in the following nominal sizes using the appropriate mounting Type of fitting Circular sight glass fitting DIN 28120 DIN 28121 Visual flow indicator Screw type sight glass fitting similar to DIN 11851 All dimensions in mm unless stated otherwise Subject to change without prior notice ric 11 09 0093 027 00 PAPENMEIER Part No 1 External protective conductor terminal
Download Pdf Manuals
Related Search