ByteBlaster II Cable User Guide
Contents
1. 2 1 Table 2 2 ByteBlaster 25 Pin Header Pin Outs 2 2 Table 2 3 ByteBlaster II Female Plug Signal Names and Programming Modes 2 3 Table 2 4 ByteBlaster II Cable Absolute Maximum Ratings 2 4 Table 2 5 ByteBlaster II Cable Recommended Operating Conditions 2 5 Table 2 6 ByteBlaster II Cable DC Operating Conditions 2 5 Table 2 7 Table of Hazardous Substances Name and Concentration 2 5 Table Info 1 Revision History screens Ead cere eade eed aga eae epe Info 2 Table Info 2 How to Contact Altera s gt is enn Info 3 Table Info 3 Typographic Conventions 22 Info 3 July 2008 Altera Corporation ByteBlaster Download Cable User Guide 6 List of Tables ByteBlaster II Download Cable User Guide July 2008 Altera Corporation 1 Setting Up the ByteBlaster JN DTE RYAN Download Cable Introduction The ByteBlaster II download cable allows you to program and configure Altera devices This cable drives configuration data from a standard parallel printer port on your PC to the device on the PCB Because design changes are downloaded directly to the device prototyping is easy and you can accomp2. ByteBlaster 11 Download Cable 4 Connect the power cable to reapply power to the circuit board ByteBlaster II Download Cable User Guide July 2008 Altera Corporation Chapter 1 Setting Up the ByteBlaster Il Download Cable 1 3 Software Setup If the Found New Hardware wizard prompts you to install a new hardware driver close the wizard and install the hardware driver using the instructions provided in Installing the Driver on a Windows System or Installing the Driver on a Linux System depending on your system Software Setup This section describes the following topics Installing the Driver on a Windows System on page 1 3 Installing the Driver on a Linux System on page 1 4 Setting Up the ByteBlaster II Hardware in the Quartus II Software on page 1 5 Installing the Driver on a Windows System This section describes how to install the ByteBlaster II driver on a Windows system Before you begin the installation verify the ByteBlaster II driver is located in your directory lt Quartus II system directory drivers win2000Nwin2000 inf Installing the Driver for Windows 2000 and Windows XP To install the driver for Windows 2000 or Windows XP perform the following steps 1 10 11 12 13 July 2008 Altera Corporation For Windows 2000 choose Settings Control Panel Windows Start menu For Windows XP choose Control Panel Windows Start menu Click Switch to Classic View if necess
3. Start the Quartus II software On the Tools menu click Programmer Click Hardware Setup The Hardware Settings tab of the Hardware Setup dialog box appears In the Currently selected hardware list select ByteBlasterII LPT1 Click Add Hardware The Add Hardware dialog box appears Select ByteBlaster or ByteBlaster II and click OK ByteBlasterII is now visible in the Available hardware items list of the Hardware Setup dialog box as shown in Figure 1 2 July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide 1 6 Chapter 1 Setting Up the ByteBlaster Il Download Cable Software Setup Figure 1 2 Hardware Setup Dialog Box Hardware Setup Hardware Settings JTAG Settings Select a programming hardware setup to use when programming devices This programming hardware setup applies only to the current programmer window ByteBlasterll LPT1 z Add Hardware Currently selected hardware Available hardware items Server Port Local LPT1 Hardware ByteBlasterll 7 Click Close to close the Hardware Setup dialog box 8 In the Mode list select the desired mode Programmer window Table 1 1 describes each mode The ByteBlaster II supports the Joint Test Action Group JTAG Passive Serial Programming and Active Serial modes Table 1 1 Programming Modes Mode Joint Test Action Group JTAG Mode Description Programs or configures all Altera devices supporte
4. Hardware Setup Software Requirements The ByteBlaster II download cable is available for Windows 2000 Windows NT Windows XD and Linux Use the Quartus II software version 4 0 or later to configure your device The ByteBlaster II download cable also supports the following tools m Quartus II Programmer for programming and configuration which you can run within the Quartus II software or as a standalone version m Quartus SignalTap Embedded Logic Analyzer for logic analysis which you can run within the Quartus II software or as a standalone version m Nios II IDE for software downloading and debugging m Nios IT IDE Flash Programmer for programming Flash devices Hardware Setup This section describes how to install and set up the ByteBlaster II download cable for device configuration and programming a gt For plug and header dimensions pin names and operating conditions refer to Chapter 2 ByteBlaster II Specifications chapter Connect your ByteBlaster II download cable to the circuit board as instructed below 1 Disconnect the power cable from the circuit board 2 Connect the ByteBlaster II cable to a parallel port on your PC 3 Connect the ByteBlaster II download cable to the 10 pin header on the device board Figure 1 1 shows the ByteBlaster II download cable and the circuit board connector Figure 1 1 The ByteBlaster I Download Cable Computer 252 ByteBlaster II 10 pin Female Plug
5. Figure 2 3 shows the dimensions of a typical 10 pin male header 2 Although a 10 pin surface mount header can be used for the JTAG AS or PS download cable Altera recommends using a through hole connector due to the repeated insertion and removal force needed Figure 2 3 10 Pin Male Header Dimensions Top View Side View 0 100 0 025 Sq 0 100 gt k gt 0 205 Dimensions are shown in inches E H H Operating Conditions Table 2 4 through Table 2 6 summarize the maximum ratings recommended operating conditions and DC operating conditions for the ByteBlaster II cable Table 2 4 ByteBlaster II Cable Absolute Maximum Ratings Note 7 Symhol Parameter Conditions Min Max Unit Input current TDO Or dataout 10 0 10 0 mA lo Output current TCK TMS TDI nCS nCE 20 0 20 0 mA Note to Table 2 4 1 The operating conditions are identical for both leaded and lead free ByteBlaster Il download cables ByteBlaster II Download Cable User Guide July 2008 Altera Corporation Chapter 2 ByteBlaster Il Specifications 2 5 Statement of China RoHS Compliance Table 2 5 ByteBlaster II Cable Recommended Operating Conditions Note 1 Symbol Parameter Conditions Min Max Unit Vecaren Target supply voltage 5 0 V operation 4 75 5 25 V Target supply voltage 3 3 V op
6. Il Download Cable Introduction i eI bee cos Hope elena debe 1 1 Supported Devices ees oriri ted centes ues uud edis a Sia bie lit Ter tonnes 1 1 Power Requirements 1 1 Software Requirements ccc rende qe cun Uu ede hd Cer cles Se ieee gs eee ee es 12 Hardware oboe ERO HERE e eee OP ERA b sonata ed se 1 2 DOM Wale C 1 3 Installing the Driver on a Windows System 1 3 Installing the Driver on a Linux System 2 eee ene es 1 4 Setting Up the ByteBlaster II Hardware in the Quartus II Software 1 5 Chapter 2 ByteBlaster Specifications OVOEVIEW irs deeft tedio eu dona ie a eta elites dE autero te ud tede lecti dud e tud 2 1 ByteBlaster II Connections riii e He nn 2 1 Voltage Requirements ee eee bre I exe Hep e ed e baden doe eed 2 1 Cable to Board Connection nE E EE eee nnn 2 2 ByteBlaster II 25 Pin Header Connection 2 2 ByteBlaster 10 Pin Header Connection 2 3 Circuit Board Header Connection 2220 2 4 Operating Conditions ER Cp ee de ae 2 4 Statement of China RoHS Compli
7. perform the following steps 1 Decompress the byteblaster tar gz file by typing the following command at the command prompt tar xzvf byteblaster tar gz 2 Access the new directory by typing the following command at the command prompt cd byteblaster ByteBlaster II Download Cable User Guide July 2008 Altera Corporation Chapter 1 Setting Up the ByteBlaster Il Download Cable 1 5 Software Setup Run the configure install script by typing the following command at the command prompt configure Compile the Altera ByteBlaster kernel driver by typing the following command at the command prompt make Become root and compile the Altera ByteBlaster kernel driver module and device nodes by typing the following command at the command prompt make install To install the Altera ByteBlaster kernel driver type the following command at the command prompt jtagconfig add byteblaster2 dev byteblaster0 To determine whether the ByteBlaster II download cable and the Altera ByteBlaster kernel driver are installed correctly display a list of available devices by typing the following command at the command prompt jtagconfig You should see a list of devices on your JTAG chain including the ByteBlaster II download cable Setting Up the ByteBlaster Il Hardware in the Quartus Il Software To set up the ByteBlaster II hardware in the Quartus II software perform the following steps 1 2 3
8. ByteBlaster Il Download Cable User Guide ANU S RA 101 Innovation Drive San Jose CA 95134 www altera com Software Version 8 0 Document Version 14 Document Date July 2008 Copyright 2008 Altera Corporation rights reserved Altera The Programmable Solutions Company the stylized Altera logo specific device designations and all other words and logos that are identified as trademarks and or service marks are unless noted otherwise the trademarks and service marks of Altera Corporation in the U S and other countries All other product or service names are the property of their respective holders Altera products are protected under numerous U S and foreign patents and pending ap plications maskwork rights and copyrights Altera warrants performance of its semiconductor products to current specifications in accordance with Altera s standard warranty but reserves the right to make changes to any products and services at any time without notice Altera assumes no responsibility or liability arising out of the application or use of any information product or service described herein except as expressly agreed to in writing by Altera Corporation Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services P25 36288 00 UG BBII81204 1 4 1 5 EN ISO 9001 NE TE 274 Contents Chapter 1 Setting Up the ByteBlaster
9. Name Description 2 DCLK Clock signal DCLK Clock signal TCK Clock signal 3 nCONFIG Configuration control nCONFIG Configuration TMS JTAG state control machine control 4 ncs Serial configuration No connect No connect device chip select ByteBlaster II Download Cable User Guide July 2008 Altera Corporation Chapter 2 ByteBlaster II Specifications 2 3 ByteBlaster 11 Connections Table 2 2 ByteBlaster 1 25 Pin Header Pin Outs Part 2 of 2 5 nCE Cyclone chip enable No connect No connect 8 ASDI Active serial data in DATAO Datato device TDI Data to device 11 CONF DONE Configuration done CONF DONE Configuration Data from device done 13 DATAOUT Active serial data out nSTATUS Signal status No connect 15 nvcc nvcc nvcc Detect Detect Detect 18 to 25 GND Signal ground GND Signal ground GND Signal ground ByteBlaster II 10 Pin Header Connection The 10 pin female plug connects to a 10 pin male header on the circuit board Figure 2 2 shows the dimensions of the female plug Figure 2 2 ByteBlaster II 10 Pin Female Plug Dimensions 0 250 Typ Dimensions are shown in inches Spacing between pin centers is 0 1 inches Table 2 3 identifies the 10 pin female plug signal names and the corresponding programming mode Table 2 3 ByteBlaster I Female Plug Signal Names and Programming Mode
10. able 2 1 Added new note to Table 2 4 Table 2 5 andTable 2 6 Added note about RoHS compliance Updated Revision History December 2004 Re release v1 1 July 2004 Initial release v1 0 ByteBlaster II Download Cable User Guide July 2008 Altera Corporation How to Contact Altera How to Contact Altera For the most up to date information about Altera products refer to the following Info 3 table Table Info 2 How to Contact Altera Contact 1 Contact Method Address Technical support Website www altera com support Technical training Website www altera com training Email custrain altera com Product literature Website www altera com literature Altera literature services Email literature altera com Non technical support General Email nacomp altera com Software Licensing Email authorization altera com Note to Table Info 2 1 You can also contact your local Altera sales office or sales representative Typographic Conventions This document uses the typographic conventions shown below Table Info 3 Typographic Conventions Part 1 of 2 Visual Cue Bold Type with Initial Capital Letters Command names dialog box titles checkbox options and dialog box options are shown in bold initial capital letters Example Save As dialog box bold type External timing parameters directory names project names disk drive names filenames filename ext
11. ance 2 nee nen 2 5 Chapter Info Additional Information Referenced Documents eee ae Mia aces ed c ael eoe eue one wai Info 1 Revision iiis sede kar eh Pee EE ee Ae Rade de Sale Knaus REOR ROI meute Info 2 How to Contact Altera Lis ids eal nia n Ver Hide dee aa e oe dare eee Info 3 Typographic Conventions 44222220 Info 3 July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide ByteBlaster 11 Download Cable User Guide July 2008 Altera Corporation List of Figures 3 List of Figures Figure 1 1 The ByteBlaster II Download Cable 1 2 Figure 1 2 Hardware Setup Dialog Box 1 6 Figure 2 1 ByteBlaster II Block Diagram 2 2 Figure 2 2 ByteBlaster 10 Pin Female Plug Dimensions 2 3 Figure 2 3 10 Pin Male Header Dimensions 2 4 July 2008 Altera Corporation ByteBlaster Download Cable User Guide 4 List of Figures ByteBlaster II Download Cable User Guide July 2008 Altera Corporation List of Tables 5 List of Tables Table 1 1 Programming Modes 1 6 Table 2 1 ByteBlaster II VCC TRGT Pin Voltage Requirements
12. anel window 3 Click the Devices tab and click the Add button 4 Click Unlisted or Updated Driver from the List of Drivers list box and click OK 5 Browse to the location of the driver on your system The default location is the lt Quartus II system directory drivers win2000 directory Click OK 6 Select Altera ByteBlaster or Altera ByteBlaster the Add Unlisted or Updated Driver window and click OK Reboot your system Installing the Driver on a Linux System The Altera ByteBlaster kernel driver is required for Linux workstations running Red Hat Linux version 7 3 or 8 0 or Red Hat Enterprise Linux version 3 0 or later that use the ByteBlaster II download cable You must install and compile the Altera ByteBlaster kernel driver separately from the Quartus II software To compile the Altera ByteBlaster kernel driver you must have the following Red Hat Package Manager RPM packages which are available from the Red Hat website at www redhat com gcc 2 96 81 make 3 79 1 5 binutils 2 10 91 0 2 3 kernel headers RPM version must correspond to kernel version To verify that an RPM is installed use the rpm q lt name gt command For example rpm q gcc verifies that the gcc RPM is installed You do not need to install the ByteBlaster IT download cable before installing the Altera ByteBlaster kernel driver You must have superuser or root privileges to install this driver To install the driver for Linux
13. ary Control Panel window Double click the Add Hardware icon to start the Add Hardware wizard and click Next to continue Select Yes I have already connected the hardware and click Next Select Add a new hardware device from the Installed hardware list and click Next to continue Select Install from a list or specified location Advanced and click Next to continue Depending on your system the wording of this option may vary slightly Select Sound video and game controllers and click Next to continue Select Have Disk and browse to the location of the driver on your system The default location is the lt Quartus II system directory drivers win2000 directory Select win2000 inf and click Open to continue Click OK to install the selected driver Click Continue Anyway when the Software Installation warning appears Select Altera ByteBlaster and click Next to continue Click Next to install the driver ByteBlaster 11 Download Cable User Guide 1 4 Chapter 1 Setting Up the ByteBlaster Il Download Cable Software Setup 14 Click Continue Anyway when the Hardware Installation warning appears 15 Click Finish in the Completing the Add Hardware Wizard window Reboot your system Installing the Driver for Windows NT To install the driver for Windows NT perform the following steps 1 For Windows NT choose Settings Control Panel Windows Start menu 2 Double click the Multimedia icon in the Control P
14. d by the Quartus II software excluding FLEX 6000 and EPCS serial configuration devices In Socket Programming Not supported by the ByteBlaster II cable Passive Serial Programming Configures all Altera devices supported by the Quartus Il software excluding MAX 3000 MAX 7000 MAX II and EPCS serial configuration devices Active Serial Programming Programs a single EPCS1 EPCS4 EPCS16 EPCS64 or EPCS128 serial configuration device ByteBlaster II Download Cable User Guide For details about the Quartus II Programmer refer to the Quartus II Programmer chapter in volume 1 of the Quartus II Handbook For details about programming devices and creating secondary programming files refer to the Programming amp Configuration chapter of the Introduction to the Quartus II Software manual For more information refer to the Programming module of the Quartus II software online tutorial and the following topics in the Quartus II Help m Changing the Hardware Setup m Programmer Introduction m Overview Working with Chain Description Files July 2008 Altera Corporation Chapter 1 Setting Up the ByteBlaster Il Download Cable 1 7 Software Setup m Overview Converting Programming Files July 2008 Altera Corporation ByteBlaster II Download Cable User Guide ByteBlaster Download Cable User Guide Chapter 1 Setting Up the ByteBlaster Il Download Cable Software Setup July 2008 Altera Corporatio
15. ensions and software utility names are shown in bold type Examples fmax qdesigns directory d drive chiptrip gdf file Italic Type with Initial Capital Letters Italic type Internal timing parameters and variables are shown in italic type Document titles are shown in italic type with initial capital letters Example AN 75 High Speed Board Design Examples N 1 Variable names are enclosed in angle brackets and shown in italic type Example file name project name gt pof file Initial Capital Letters Keyboard keys and menu names are shown with initial capital letters Examples Delete key the Options menu Subheading Title References to sections within a document and titles of on line help topics are shown in quotation marks Example Typographic Conventions Courier type Signal and port names are shown in lowercase Courier type Examples aata1 tdi input Active low signals are denoted by suffix n for example resetn Anything that must be typed exactly as it displays is shown in Courier type For example c qdesigns tutorial chiptrip gaf Also sections of an actual file such as Report File references to parts of files for example the AHDL keyword suBDESTIGN as well as logic function names 0 TRI are shown in Courier 1 2 3 and Numbered steps are used in a list of items when the sequence of the items is important a b C etc such as t
16. eration 3 0 3 6 V Target supply voltage 2 5 V operation m 2 375 2 625 V Target supply voltage 1 8 V operation 1 71 1 89 V Target supply voltage 1 5 V operation 1 43 1 57 V Note to Table 2 5 1 The operating conditions are identical for both leaded and lead free ByteBlaster Il download cables Table 2 6 ByteBlaster Cable DC Operating Conditions Note 7 Symbol Parameter Conditions Min Max Unit Vin High level input voltage VCC TRGT 0 2 V Vit Low level input voltage 0 15 V Von 5 0 V high level output voltage VCC TRGT 4 5 V IOH 8 mA 4 4 V 3 3 V high level output voltage VCC TRGT 3 0 V IOH 4 mA 2 9 V 2 5 V high level output voltage VCC TRGT 2 375 V 2 mA 2 275 V 1 8 V high level output voltage VCC TRGT 1 71 V 2 mA 1 61 V 1 5 V high level output voltage VCC TRGT 1 43 V IOH 2 mA 1 33 V Vo 5 0 V low level output voltage VCC TRGT 5 5 V IOL 8 mA 0 125 V 3 3 V low level output voltage VCC TRGT 3 6 V IOL 4 mA 0 125 V 2 5 V low level output voltage VCC TRGT 2 625 V IOL 2 mA 0 125 V 1 8 V low level output voltage VCC TRGT 1 89 V IOL 2 mA 0 125 V 1 5 V low level output voltage VCC TRGT 1 57 V IOL 2 mA 0 125 V lcc ren Operating current No Load Typical ICC 80 mA 150 mA Note to Table 2 6 1 The DC operating conditions are identical for both leaded and lead free ByteBla
17. he steps listed in a procedure mee Bullets are used in a list of items when the sequence of the items is not important v The checkmark indicates a procedure that consists of one step only July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide Info 4 Table Info 3 Typographic Conventions Part 2 of 2 Typographic Conventions cs Visual Cue The hand points to information that requires special attention CAUTION A caution calls attention to a condition or possible situation that can damage or destroy the product or the user s work WARNING A warning calls attention to a condition or possible situation that can cause injury to the user FI The angled arrow indicates you should press the Enter key The feet direct you to more information about a particular topic ByteBlaster II Download Cable User Guide July 2008 Altera Corporation
18. lish multiple design iterations in quick succession Supported Devices You can use the ByteBlaster II download cable to download configuration data to the following Altera devices m Stratix series FPGAs Cyclone series FPGAs MAX series CPLDs Arria GX series FPGAs APEX series FPGAs ACEX 1K FPGAs Mercury FPGAs FLEX 10K series FPGAs Excalibur FPGAs You can perform in system programming of the following devices m Advanced configuration devices including EPC2 EPC4 EPC8 and EPC16 devices m Serial configuration devices including EPCS1 EPCS4 EPCS16 EPCS64 and EPCS128 devices In addition you can perform SignalTap II logic analysis The ByteBlaster II download cable supports target systems using 5 0 V TTL 3 3 V LVTTL LVCMOS and single ended I O standards from 1 5 V to 3 3 V Power Requirements The ByteBlaster II download cable requires between 1 5 V and 5 0 V from the target circuit board The ByteBlaster II cable can be used in 1 8 V 2 5 V 3 3 V and 5 0 V systems The ByteBlaster II pin must be connected to the appropriate voltage for the device that is being programmed The pull up resistors on the target circuit board for the configuration programming signals must be connected to the same power supply as the ByteBlaster II July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide 1 2 Chapter 1 Setting Up the ByteBlaster Il Download Cable
19. n ANU RYN 2 ByteBlaster Il Specifications Overview TM This chapter provides comprehensive information about the ByteBlaster II download cable including the following m ByteBlaster II connections m Voltage requirements m Cable to board connection m ByteBlaster II 25 pin header connection m ByteBlaster II 10 pin header connection m Circuit board header connection m Operating conditions ByteBlaster Il Connections The ByteBlaster II cable has a 25 pin male header parallel printer plug that connects to the PC and a 10 pin female plug that connects to the circuit board Data is downloaded from the parallel printer port on the PC through the ByteBlaster II cable to the circuit board Voltage Requirements The ByteBlaster II Vccrrcr pin must be connected to a specific voltage for the device that is being programmed Connect pull up resistors to the same power supply as the ByteBlaster II Refer to Table 2 1 for voltage requirements for specific device families Table 2 1 ByteBlaster II Vcc ragr Pin Voltage Requirements Device Family MAX II devices ByteBlaster Il VCC Voltage Required As specified by VCCIO of Bank 1 MAX 70008 devices 5V MAX 7000AE and MAX 3000A devices 3 3 V MAX 7000B device 25V Stratix IIl and Stratix IV devices As specified by Vecpem OF Cyclone III devices As specified by Veca Or Vecio Stra
20. ore information about configuration and in system programmability ISP refer to the following sources July 2008 Altera Corporation AN 39 IEEE 1149 1 JTAG Boundary Scan Testing in Altera Devices AN 95 In System Programmability in MAX Devices Configuring Arria GX Devices chapter in volume 2 of the Arria GX Device Handbook Configuring Cyclone FPGAs chapter in the Cyclone Device Handbook Configuring Cyclone II Devices chapter in the Cyclone II Device Handbook Configuring Cyclone III Devices chapter in volume 1 of the Cyclone III Device Handbook Configuring Stratix and Stratix GX Devices chapter in the Stratix Device Handbook Configuring Stratix II and Stratix II GX Devices chapter in volume 2 of the Stratix II Device Handbook Configuring Stratix Devices chapter in volume 1 of the Stratix III Device Handbook In System Programmability Guidelines for MAX II Devices chapter in the MAX II Device Handbook Configuration Design Security and Remote System Upgrades in Stratix IV Devices chapter in volume 1 of the Stratix IV Device Handbook Programming amp Configuration chapter in the Introduction to the Quartus II Software manual Quartus II Programmer chapter in volume 3 of the Quartus II Handbook Serial Configuration Devices EPCS1 EPCS4 EPCS16 EPCS64 and EPCS128 Data Sheet chapter in the Configuration Handbook Programming module of the Quartus II online tutorial Refer to the following glossary definitions in Quart
21. s Part 1 of 2 AS Mode PS Mode JTAG Mode Pin Signal Name Description Signal Name Description Signal Name Description 1 DCLK Clock signal DCLK Clock signal TCK Clock signal 2 GND Signal ground GND Signal ground GND Signal ground 3 CONF DONE Configuration done CONF DONE Configuration done Data from device 4 vcc TRGT Target power supply vcC TRGT Target power supply VCC TRGT Target power supply 5 nCONFIG Configuration control ncONFIG Configuration control TMS JTAG state machine control 6 nCE Cyclone chip enable No connect No connect 7 DATAOUT Active serial data out nSTATUS Configuration status No connect 8 nCS Serial configuration No connect No connect device chip select July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide 2 4 Chapter 2 ByteBlaster Il Specifications Operating Conditions Table 2 3 ByteBlaster Female Plug Signal Names and Programming Modes Part 2 of 2 9 ASDI Active serial data in DATAO Data to device TDI Data to device 10 GND Signal ground GND Signal ground GND Signal ground La The circuit board must supply VCC TRGT and ground to the ByteBlaster II cable for the I O drivers Circuit Board Header Connection The circuit board s 10 pin male header has two rows of five pins connected to the device s programming or configuration pins
22. ster 11 download cables 5 The RoHS sticker on the ByteBlaster II download cable reflects the hardware upgrade to meet the RoHS lead free requirement Gy download cable Statement of China RoHS Compliance Table 2 7 lists hazardous substances included with the lead free ByteBlaster Table 2 7 Table of Hazardous Substances Name and Concentration Note 1 Hexavalent Polybrominated Chromium Polybrominated diphenyl Ethers Part Name Lead Pb Cadmium Cd Cr6 Mercury Hg biphenyls PBB PBDE Electronic 0 0 0 0 0 0 Components Populated 0 0 0 0 0 0 Circuit Board July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide 2 6 Table 2 7 Table of Hazardous Substances Name and Concentration Note 1 Chapter 2 ByteBlaster Il Specifications Statement of China RoHS Compliance Hexavalent Polybrominated Chromium Polybrominated diphenyl Ethers Part Name Lead Pb Cadmium Cd Cr6 Mercury Hg biphenyls PBB PBDE Manufacturing 0 0 0 0 0 0 Process Packing 0 0 0 0 0 0 Notes to Table 2 7 1 indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard ByteBlaster II Download Cable User Guide July 2008 Altera Corporation Info Additional Information ANU S RYA Referenced Doc uments For m
23. tix lI Stratix Stratix II GX Stratix GX and Arria GX devices As specified by VCCSEL Cyclone Il Cyclone APEX Il APEX 20K and Mercury devices As specified by VCCIO FLEX 10 FLEX 8000 and FLEX 6000 devices 5V FLEX 10KE devices 25V FLEX 10KA and FLEX 6000A devices 3 3V EPC2 5Vor3 3V July 2008 Altera Corporation ByteBlaster 11 Download Cable User Guide 2 2 Chapter 2 ByteBlaster Il Specifications ByteBlaster 1 Connections Table 2 1 ByteBlaster Il Pin Voltage Requirements Part 2 of 2 4 8 and EPC16 devices 3 3 V EPCS1 EPCS4 EPCS16 EPCS64 and EPCS128 devices 3 3 V Cable to Board Connection The ByteBlaster II cable has a standard parallel printer plug that connects to the PC Figure 2 1 shows a block diagram of the ByteBlaster II download cable Figure 2 1 ByteBlaster I Block Diagram Voc Voc 2222 4 18 25 gt Series Resistors for Signal Quality er and Parallel Port Protection GND Typically 100 Q GND ByteBlaster Il 25 Pin Header Connection The 25 pin male header connects to a parallel port with a standard parallel cable Table 2 2 identifies the plug pin names and the corresponding programming modes Table 2 2 ByteBlaster II 25 Pin Header Pin Outs Part 1 of 2 AS Mode PS Mode JTAG Mode Pin Signal Name Description Signal Name Description Signal
24. us II Help m ByteBlaster II Cable general description m Configuration scheme general description m Programming files general description Refer to the following procedures in Quartus II Help m Programming a Single Device or Multiple Devices in JTAG or Passive Serial Mode m Programming a Single Device in Active Serial Programming Mode m Selecting the Communications Cable for the SignalTap II Logic Analyzer ByteBlaster II Download Cable User Guide Info 2 Revision History m Refer to the following introduction and overview topics in Quartus II Help m Programmer Introduction m Overview Working with Chain Description Files m Overview Converting Programming Files Revision History The following table shows the revision history of this user guide Table Info 1 Revision History Date and Document Version Changes Made Summary of Changes July 2008 Updates included v1 4 m Added the Additional Information page m General update to the format and style of the user guide m Updated the Supported Devices section m Updated the Setting Up the ByteBlaster I Hardware the Quartus Il Software section m Updated Table 2 1 m Added a hand note to the Circuit Board Header Connection section m Updated Table 2 6 April 2008 Added Statement of China RoHS Compliance section v1 3 Added Table 2 7 January 2008 Updated Supported Devices section v1 2 Updated Table 1 1 Updated T
Download Pdf Manuals
Related Search