Home

NLS-HR15 Series User Guide

Contents

1. Enable Disable PDF417 PDF417 is enabled by default 99201 Enable PDF417 99920101 Disable PDF417 Note Ifthe scanner fails to identify PDF417 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable PDF417 barcode Maximum length supported 2710 bytes 99900032 Exit Setup 142 9900031 99 Enter Setup 143 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for PDF417 To set the Code ID scan the Set Code ID for PDF417 barcode the numeric barcodes corresponding to the hexadecimal 011 99920115 Set Code ID for PDF417 value of a desired ID and the Save barcode Example Set the Code ID of PDF417 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for PDF417 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Set Length Range for PDF417 The scanner can be configured to only decode PDF417 barcodes with lengths that fall between inclusive the minimum and maxi
2. 152 Parameter Default Remark Maximum Length 255 Minmum Length 1 AIM128 AIM 128 Disabled Maximum Length 255 Minmum Length 1 EAN 8 EAN 8 Enabled Check Digit Transmit 2 Digit Add On Code Disabled 5 Digit Add On Code Disabled Decode EAN 8 2 digit Add On Code Only Disabled Decode EAN 8 5 digit Add On Code Only Disabled Extend to EAN 13 Disabled Convert to EAN 13 Disabled EAN 13 EAN 13 Enabled Check Digit Transmit 2 Digit Add On Code Disabled 5 Digit Add On Code Disabled Decode EAN 13 2 digit Add On Code Only Disabled Decode EAN 13 5 digit Add On Code Only Disabled ISSN ISSN Disabled 153 Parameter Default Remark ISBN ISBN Disabled ISBN Format ISBN 13 UPC E Enable On Send the Check Character On Read 2 Digits Extracode Off Read 5 Digits Extracode Off Extracode is Required 2 digits Off Extracode is Required 5 digits Off Extend to UPC A Off Type is UPC A when Extend Off System Character 0 Do not transmit UPC A UPC A Enabled Check Digit Transmit 2 Digit Add On Code Disabled 5 Digit Add On Code Disabled Decode UPC A 2 digit Add On Code Only Disabled Decode UPC A 5 digit Add On Code Only Disabled Preamble Character 0 Do not transmit Interleaved 2 of 5 Interleaved 2 of 5 Enabled Parity Check En
3. Disable Custom Prefix Enable Custom Prefix Set Custom Prefix To set a custom prefix scan the Set Custom Prefix barcode the numeric barcodes corresponding to the hexadecimal value of a desired prefix and the Save barcode Note A custom prefix cannot exceed 11 characters 99904022 Set Custom Prefix Example set the custom prefix to CODE its hexadecimal value is 0x43 0x4F 0x44 0x45 1 Scan the Enter Setup barcode Scan the Set Custom Prefix barcode Scan the numeric barcodes 4 3 4 F 4 4 4 and 5 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 Scan the Enable Custom Prefix barcode Dapo LD Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 AIM ID Prefix AIM Automatic Identification Manufacturers ID defines symbology identifier For the details see the AIM ID Table section in Chapter 7 If AIM ID prefix is enabled the scanner will add the symbology identifier before the scanned data after decoding By default AIM ID prefix is disabled 99 90403 0 Disable AIM ID Prefix 999040 Enable AIM ID Prefix 31 Code ID Prefix Code ID can also be used to identify barcode type Unlike AIM ID Code ID is user programmable To learn how to program it see the Set Code ID secti
4. 99 9 1000 Set Code ID for Code 128 Example Set the Code ID of Code 128 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Code 128 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 Set Length Range for Code 128 The scanner can be configured to only decode Code 128 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 1 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Code 128 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Code 128 barcodes with that length are to be decoded The default minimum and maximum lengths are 1 character and 255 characters respectively 99910004 Set the Minimum Length Set the Maximum Length Example Set the scanner to decode Code128 barcodes containing between 8 and 12 characters 1 Scan the Enter Setup barcode 2 Scan the Set the Minimum Length barcode 3 Scan the numeric barcode 8 See the Digit Barcodes section in Chapter 7 4 Scan the S
5. Enable Disable ISBN ISBN is disabled by default 99910702 Il Enable ISBN 99910701 Disable ISBN Note If the scanner fails to identify ISBN barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable ISBN barcode 0032 9990 Exit Setup 74 9900031 99 Enter Setup Set ISBN Format The default format is ISBN 13 91 99910703 ISBN 13 91 ISBN 10 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for ISBN To set the Code ID scan the Set Code ID for ISBN barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99910705 9 Set Code ID for ISBN Example Set the Code ID of ISBN to p its hexadecimal value is 0x70 1 2 75 Scan the Enter Setup barcode Scan the Set Code ID for ISBN barcode Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 UPC E Restore Default Settings Scan the barcode below to restore all parameters in UPC E configuration to the factory default settings To find the related default settings see t
6. 2 Newland gt NLS HR15 Series NLS HR1550 30 Corded 1D Barcode Scanner User Guide Disclaimer 2013 Fujian Newland Auto ID Tech Co Ltd All rights reserved Please read through the manual carefully before using the product and operate it according to the manual It is advised that you should keep this manual for future reference Do not disassemble the device or remove the seal label from the device Otherwise FuJian Newland Auto ID Tech Co Ltd does not assume responsibility for the warranty or replacement All pictures in this manual are for reference only and actual product may differ Regarding to the product modification and update FuJian Newland Auto ID Tech Co Ltd reserves the right to make changes to any software or product to improve reliability function or design at any time without notice Besides the information contained herein is subject to change without prior notice The products depicted in this manual may include software copyrighted by FuJian Newland Auto ID Tech Co Ltd or a third party The user corporation or individual shall not duplicate in whole or in part distribute modify decompile disassemble decode reverse engineer rent transfer or sublicense such software without prior written consent from the copyright holders This manual is copyrighted No part of this publication may be reproduced or used in any form without written permission from Newland FuJian Newland Auto I
7. 7 DATA2 1 0 PC keyboard signal 8 GND P Ground 9 D 1 0 USB signal 10 D 1 0 Connect HR15 to a Host HR15 corded scanner must be connected to a host device in actual application such as PC POS or any intelligent terminal with USB or RS 232 or PS 2 port using a communication cable USB or RS 232 or PS 2 cable USB USB port on the host RS 232 AD port on the host PS 2 PS 2 port on the host Note Please check the port on the host and purchase the right cable Use USB Cable Fig 1 3 Connect HR15 corded scanner to a Host through a USB cable with RJ45 and USB connectors 1 Plug the RJ45 connector into the data port see Fig 1 1 on the scanner 2 Plug the USB connector into the USB port on the Host Use RS 232 Cable Connect HR15 corded scanner to a Host through an RS 232 cable with RJ45 RS 232 connectors and a power jack 1 Plug the RJ45 connector into the data port see Fig 1 1 on the scanner 2 Plug the RS 232 connector into the RS 232 port on the Host 3 Plug the power adapter into the power jack Use PS 2 Cable Fig 1 5 Connect HR15 corded scanner to a Host through a PS 2 cable equipped with PS 2 and RJ45 connectors PS 2 female socket and power jack Only applicable to HR1550 33 Plug the RJ45 connector into the data port see Fig 1 1 on the scanner Plug the PS 2 connector into the PS 2 port on the Host If necessary plug the power adapter into the power jac
8. 99904403 Read 3 Barcodes Per Scan 99904404 Read 4 Barcodes Per Scan 99904410 Set Output Interval to Oms 99904411 Set Output Interval to 50ms 37 99904400 Read One Barcode Nearest to the Center Per Scan 99 C 904401 Read One Barcode At The Center Per Scan 99904412 Set Output Interval to 100ms 99904413 Set Output Interval to 150ms 99900032 Exit Setup 99900031 Enter Setup Other Settings Temporary Mute 99900040 Enable Temporary Mute 99900041 Disable Temporary Mute Note Temporary Mute is only applicable to decode beep and will be disabled after you reboot the scanner 0032 9990 Exit Setup 38 003 9990 1 Enter Setup Chapter 3 Inquiry Command Introduction You can scan one of the barcodes below to inquire the scanner information The results will be sent to the Host 99900303 Inquire all Information Inquire the Manufacture Date 99900304 Inquire the Firmware Version Inquire the Model Number 99900302 Inquire the Serial Number 0032 9990 39 Exit Setup 99900031 Enter Setup Chapter 4 Communication Settings RS 232 Interface Baud Rate When the scanner is connected to the Host via serial port you need to set communication parameters including baud rate parity check data bit and stop bit to match the host device Baud rate is
9. 2 Stop Bits 99902164 8 Data Bits Even Parity 2 Stop Bits 99902165 8 Data Bits Odd Parity 2 Stop Bits 99902167 7 Data Bits Even Parity 2 Stop Bits 99902170 7 Data Bits Odd Parity 2 Stop Bits 99902171 7 Data Bits Odd Parity 2 Stop Bits 44 900031 99 Enter Setup USB Interface By default the USB HID KBW option is enabled USB HID KBW 0 9990 902 30 USB HID KBW USB COM Port Emulation 01 USB COM Port Emulation 999023 90 99900032 45 Exit Setup 99900031 Enter Setup Keyboard Parameters Keyboard Layout By default the 1 US English option is enabled 1 US English 99902207 7 Italy IA I UNA 2 Japanese 99902210 8 Norway 3 Denmark 99902211 9 Spain 4 Finland 99902212 10 Turkey Q 99902213 5 France 111 UK 99902206 6 Turkey F 0032 9990 Exit Setup 46 47 Inter Character Delay 99900031 Enter Setup Inter character Delay 00 15 16 levels corresponding to Oms default 5ms 10ms 75ms in 5ms increments Inter Character Delay Convert Case By default the No Case Conversion option is enabled 99902230 No Case Conversion 99902231 o Convert All to Uppercase 99902232 JIULLIL Convert All to Lowe
10. 31 0 345870033 FAX 31 0 3458700 39 Email salesOnewland id com WEB www newland id com Tech Support tech support newland id com Newland North America Inc JE Abts REA Address 46559 Fremont Blvd gt Fremont CA 94538 gt USA TEL 510 490 3888 Fax 510 490 3887 Email info newlandna com WEB www newlandna com Newland Taiwan Inc Gwar KPA ARR AIRE A 7F 6 gt No 268 Liancheng Rd gt Jhonghe Dist 235 gt New Taipei City gt Taiwan HC 235 HA ES 268 3 7 26 eR ACE J ER TEL 886 2 7731 5388 FAX 886 2 7731 5389 Email sales tw newland id com WEB www newland id com tw
11. 99900032 Exit Setup 99900031 Enter Setup 0 Transmit System Character 0 The first character of UPC E barcode is the system character 0 By default the scanner does not transmit system character 0 99911014 Do Not Transmit System Character 0 Transmit System Character 0 UPC E Extension lt Disable UPC E Extend Transmit UPC E barcodes as is Enable UPC E Extend Extend UPC E barcodes to make them compatible in length to UPC A lt Convert UPC E to UPC A Extend UPC E barcodes to make them compatible in format to UPC A 99911016 91101 Enable UPC E Extend Disable UPC E Extend 99911017 Convert UPC E to UPC A 0032 9990 Exit Setup 80 9900031 99 Enter Setup UPC A Restore Default Settings Scan the barcode below to restore all parameters in UPC A configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99911100 Restore the Default Settings of UPC A Enable Disable UPC A UPC A is enabled by default 99911102 Enable UPC A 99911101 Disable UPC A Note If the scanner fails to identify UPC A barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable UPC A barcode 99900032 81 Exit Setup 99900031 Enter Setup 0
12. Fig 1 14 99900031 Enter Setup Chapter 2 General Settings Introduction There are two ways to configure the HR15 corded scanner barcode programming and command programming Barcode Programming The HR15 corded scanner scans a series of barcodes to program features In the following sections we will explain the available options and features and provide the barcodes to program them This programming method is most straightforward However it requires manually scanning barcodes As a result errors are more likely to occur Command Programming You can send the command strings through the Host to your scanner to perform configuration In the following sections the commands will be provided along with programming barcodes This configuration can also be performed through our software For more information see the EzSet123 Scanner Configuration Utility User Guide Note All settings except temporary ones are stored in non volatile memory of the scanner and will not be lost by removing power from the scanner or turning off rebooting the device 99900032 Exit Setup 16 99900031 Enter Setup Programming Barcode Programming Command Function 4 gt FlfEnter Setup 3 The figure above is an example that shows you the programming barcode and command for the Enter Setup function 1 The Enter Setup barcode 2 The Enter Setup command 3 The f
13. Scan the Exit Setup barcode 0032 9990 Exit Setup 64 65 9900031 99 Enter Setup 2 Digit Add On Code An EAN 8 barcode can be augmented with a two digit add on code to form a new one 99910406 Disable 2 Digit Add On Code 99910407 Decode EAN 8 2 Digit Add On Code Only Enable 2 Digit Add On Code Note Disable 2 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard EAN 8 barcodes lt Enable 2 Digit Add On Code The scanner decodes a mix of EAN 8 barcodes with and without 2 digit add on codes Decode EAN 8 2 Digit Add On Code Only The scanner only decodes new barcodes combining 2 digit add on codes 99900032 Exit Setup 99900031 Enter Setup 0 5 Digit Add On Code An EAN 8 barcode can be augmented with a five digit add on code to form a new one 99910411 Disable 5 Digit Add On Code 99910412 Decode EAN 8 5 Digit Add On Code Only Enable 5 Digit Add On Code Note Disable 5 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard EAN 8 barcodes lt Enable 5 Digit Add On Code The scanner decodes a mix of EAN 8 barcodes with and without 5 digit add on codes Decode EAN 8 5 Digit Add On Code Only The scanner only decodes EAN 8 barcodes with 5 digit add on codes 00032 9990
14. Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for UPC A To set the Code ID scan the Set Code ID for UPC A barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99911115 9 Set Code ID for UPC A Example Set the Code ID of UPC A to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for UPC A barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 0032 9990 Exit Setup 82 99900031 Enter Setup Transmit Check Digit UPC A is 13 digits in length with the last one as its check digit used to verify the accuracy of the data By default the scanner transmits UPC A check digit 9991110 Transmit UPC A Check Digit 3 Do Not Transmit UPC A Check Digit Transmit Preamble Character 0 The first character of UPC A barcode is the preamble character 0 By default the scanner does not transmit preamble character 0 99911114 Do not Transmit Preamble Character 0 Transmit Preamble Character 0 99900032 83 Exit Setup 99900031 Enter Setup 0 2 Digit Ad
15. default 7 5s in 0 5s increments 99900151 Blink Mode Timeout between Decodes Example Set the Timeout between Decodes to 5s level 10 1 Scan the Enter Setup barcode 2 Scan the Timeout between Decodes barcode 3 Scan the numeric barcodes 1 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Exit Setup barcode 99900032 Exit Setup 26 9900031 99 Enter Setup Sense Mode Sense Mode The scanner activates a decode session every time when it detects a change in ambient illumination excluding the situation when change is detected before the timeout between decodes occurs Decode session continues until the barcode is decoded or the decode session timeout occurs Pressing the trigger can also activate a decode session Holding down the trigger can suspend decode session Same barcode cannot be reread before the timeout between decodes same barcode occurs 99900113 Sense Mode Decode Session Timeout This parameter sets the maximum time decode session continues during a scan attempt The default timeout is 15s To program this parameter scan the Decode Session Timeout barcode and the numeric barcodes Timeout between Decodes This parameter sets the time period between the end of one decode session and the start of next session It is programmable in 0 5s increments from Os to 7 5s The default timeout is 1s To program this parameter scan the Timeo
16. section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check A check digit is optional for Matrix 2 of 5 and can be added as the last digit lt is a calculated value used to verify the accuracy of the data By default the scanner does not run parity check lt No Parity Check The scanner transmits Matrix 2 of 5 barcodes as is lt Do Not Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Matrix 2 of 5 barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Matrix 2 of 5 barcode as check digit Barcodes passing the check will be transmitted whereas those failing it will not be transmitted 999120 No Parity Check 9991200 5 Do Not Transmit Check Digit After Parity Check 04 Transmit Check Digit After Parity Check Note If the Do Not Transmit Check Digit After Parity Check option is enabled Matrix 2 of 5 barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check
17. you forget previous configuration and want to avoid its impact 3 functions that are rarely used have been enabled for the time being 99900030 Reset Scanner 99900032 01 Exit Setup 99900031 Enter Setup 0 Operating Mode Options 99900100 Hil Power Off 99900103 Test Mode 99900104 Deep Sleep Mode Reboot Scanner 99900102 Light Sleep Mode Note 1 The scanner that has been turned off in this way cannot be awakened To turn it back on disconnect it from the host device and reconnect it 2 To awaken the scanner press the trigger 3 To awaken the scanner press the trigger or communicate with the scanner 4 Pressing the trigger can exit the Test mode The Test mode Deep Sleep mode and Light Sleep mode are available for temporary use only They will become invalid after the scanner is restarted rebooted 9900032 99 Exit Setup 22 99900031 Enter Setup Scan Mode Manual Mode Manual Mode default A trigger pull activates a decode session The decode session continues until the barcode is decoded or you release the trigger or the decode session timeout occurs default 15 seconds programmable 99900110 Manual Mode 1 Decode Session Timeout This parameter sets the maximum time decode session continues during a scan attempt The default timeout is 15s To program this parameter scan the
18. 50 C 14F to 122 F 20 C to 60 C 4 F to 140 F 5 95 non condensing 8 KV contact discharge 15 KV air discharge Withstand multiple 1 5m drops to concrete IP54 Test conditions Code 39 3 Bytes Narrow Space 10mil Width Narrow 2 5 1 PCS 0 8 Barcode Height 40mm Scan Distance 210mm Ambient Temperature 23 C Illumination 200 LUX Dimensions Side View Front View Fig 1 9 Top View Unit mm Scanning Instructions When the HR15 corded scanner is in the Manual mode default you can follow the steps below to scan a barcode 1 Hold down the trigger Then the scanner will project a red aiming beam 2 Aim the red beam across the center of barcode as shown in Fig 1 11 3 Release the trigger when the scanner beeps and the red beam goes off If the barcode is decoded successfully the data will be sent to the Host Note For the same batch of barcodes the scanner will keep a very high success ratio in certain distance which can be regarded as the optimal scanning distance Scan Angle The scanner is designed to function within a certain range of scan angles Any unreasonable deviation may cause decoding failure Scan angles of the scanner Pitch 55 0 Roll and 0 Skew Fig 1 12 lt lt Roll 30 0 Pitch and 0 Skew Fig 1 13 Skew 75 0 Roll and 0 Pitch Fig 1 14 MF Pitch pen Fig 1 12 Fig 1 13 nae Skew
19. Default Settings of ISSN Enable Disable ISSN ISSN is disabled by default 99910601 Enable ISSN Disable ISSN Note If the scanner fails to identify ISSN barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable ISSN barcode 0032 9990 Exit Setup 72 9900031 99 Enter Setup 73 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for ISSN To set the Code ID scan the Set Code ID for ISSN barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 9991 0 603 Set Code ID for ISSN Example Set the Code ID of ISSN to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for ISSN barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 ISBN Restore Default Settings Scan the barcode below to restore all parameters in ISBN configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99910700 Restore the Default Settings of ISBN
20. Enable GS1 Databar 1 Disable GS1 Databar 0 Note If the scanner fails to identify GS1 Databar barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable GS1 Databar barcode 99900032 Exit Setup 140 9900031 99 Enter Setup 141 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for GS1 Databar To set the Code ID scan the Set Code ID for GS1 Databar barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 9913203 99 Set Code ID for GS1 Databar Example Set the Code ID of GS1 Databar to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for GS1 Databar barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 PDF417 Restore Default Settings Scan the barcode below to restore all parameters in PDF417 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99920100 Restore the Default Settings of PDF417
21. Note Disable 2 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard EAN 13 barcodes lt Enable 2 Digit Add On Code The scanner decodes a mix of EAN 13 barcodes with and without 2 digit add on codes Decode EAN 13 2 Digit Add On Code Only The scanner only decodes new barcodes combining 2 digit add on codes 9900032 99 Exit Setup 70 71 9900031 99 Enter Setup 5 Digit Add On Code An EAN 13 barcode can be augmented with a five digit add on code to form a new one 99910510 Disable 5 Digit Add On Code 99910512 Decode EAN 13 5 Digit Add On Code Only 1 99910511 Enable 5 Digit Add On Code 1 Note Disable 5 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard EAN 13 barcodes lt Enable 5 Digit Add On Code The scanner decodes a mix of EAN 13 barcodes with and without 5 digit add on codes Decode EAN 13 5 Digit Add On Code Only The scanner only decodes new barcodes combining 5 digit add on codes 99900032 Exit Setup 99900031 Enter Setup 0 ISSN Restore Default Settings Scan the barcode below to restore all parameters in ISSN configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 MDI Restore the
22. See the Code ID Table section in Chapter 7 to find the default Code ID for COOP 25 To set the Code ID scan the Set Code ID for COOP 25 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99 91 1710 Set Code ID for COOP 25 Example Set the Code ID of COOP 25 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for COOP 25 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 Parity Check A check digit is optional for COOP 25 and can be added as the last digit It is a calculated value used to verify the accuracy of the data By default the scanner does not run parity check No Parity Check The scanner transmits COOP 25 barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of COOP 25 barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of COOP 25 barcode as check digit Barcodes passing the check will be tra
23. Setup 9900032 99 99900031 Enter Setup 0 Matrix 2 of 5 European Matrix 2 of 5 Restore Default Settings Scan the barcode below to restore all parameters in Matrix 2 of 5 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912000 Restore the Default Settings of Matrix 2 of 5 Enable Disable Matrix 2 of 5 Matrix 2 of 5 is enabled by default 99 001 Enable Matrix 2 of 5 912 Disable Matrix 2 of 5 Note If the scanner fails to identify Matrix 2 of 5 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Matrix 2 of 5 barcode 99900032 Exit Setup 102 9900031 99 Enter Setup 103 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Matrix 2 of 5 To set the Code ID scan the Set Code ID for Matrix 2 of 5 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99120 99 l 0 Set Code ID for Matrix 2 of 5 Example Set the Code ID of Matrix 2 of 5 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Matrix 2 of 5 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes
24. Setup barcode 99900032 77 Exit Setup 99900031 Enter Setup 0 2 Digit Add On Code A UPC E barcode can be augmented with a two digit add on code to form a new one Disable 2 Digit Add On Code 99911006 Enable 2 Digit Add On Code 999110 911007 Decode UPC E 2 Digit Add On Code Only 1 Note Disable 2 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard UPC E barcodes lt Enable 2 Digit Add On Code The scanner decodes a mix of UPC E barcodes with and without 2 digit add on codes Decode UPC E 2 Digit Add On Code Only The scanner only decodes new barcodes combining 2 digit add on codes 00032 9990 Exit Setup 78 79 9900031 99 Enter Setup 5 Digit Add On Code A UPC E barcode can be augmented with a five digit add on code to form a new one Disable 5 Digit Add On Code 99911011 Enable 5 Digit Add On Code 99911012 9 Decode UPC E 5 Digit Add On Code Only 1 Note Disable 5 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard UPC E barcodes lt Enable 5 Digit Add On Code The scanner decodes a mix of UPC E barcodes with and without 5 digit add on codes Decode UPC E 5 Digit Add On Code Only The scanner only decodes new barcodes combining 5 digit add on codes
25. barcode 0032 9990 Exit Setup 68 9900031 99 Enter Setup 69 Transmit Check Digit EAN 13 is 13 digits in length with the last one as its check digit used to verify the accuracy of the data By default the scamner transmits EAN 13 check digit 99 91 91 05 Do Not Transmit EAN 13 Check Digit 3 Transmit EAN 13 Check Digit 0 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for EAN 13 To set the Code ID scan the Set Code ID for EAN 13 barcode the numeric barcodes corresponding to the hexadecimal 99910513 91 value of a desired ID and the Save barcode Set Code ID for EAN 13 Example Set the Code ID of EAN 13 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for EAN 13 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 2 Digit Add On Code An EAN 13 barcode can be augmented with a two digit add on code to form a new one 99910505 Disable 2 Digit Add On Code 99910507 Decode EAN 13 2 Digit Supplement Only 99910506 Enable 2 Digit Add On Code
26. barcode 2 Scan the Set Code ID for Code 93 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check Check digits are optional for Code 93 and can be added as the last two digits which are calculated values used to verify the accuracy of the data By default the scanner does not transmit check digits after parity check lt No Parity Check The scanner transmits Code 93 barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run parity checks using the last two digit of Code 93 barcode as check digits Barcodes passing the checks will be transmitted except the last two digits whereas those failing them will not be transmitted Transmit Check Digit After Parity Check The scanner will run parity checks using the last two digits of Code 93 barcode as check digits Barcodes passing the checks will be transmitted whereas those failing them will not be transmitted 99912 No Parity Check 9912605 Transmit Check Digit After Parity Check 99912604 Do Not Transmit Check Digit After Parity Check Note If the Do Not Transmit Check Digit After Parity Check option is enabled Code 93 barcodes with a length that is less than th
27. can be added as the last digit It is a calculated value used to verify the accuracy of the data By default the scanner does not run parity check lt No Parity Check The scanner transmits Code 39 barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Code 39 barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Code 39 barcode as check digit Barcodes passing the check will be transmitted whereas those failing it will not be 99124 99 No Parity Check 99 Transmit Check Digit After Parity Check 99912404 Do Not Transmit Check Digit After Parity Check transmitted 05 Note If the Do Not Transmit Check Digit After Parity Check option is enabled Code 39 barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check option is enabled and the minimum length is set to 4 Code 39 barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 116 9900031 99 Enter Setup Transmit Start Stop Character Code 39 uses an asterisk for both the start
28. ceed T 11 SpecificatiONS iii nied Sele EIR RU ee 12 DIMENSIONS v5 ducati lada ia 13 SIJE MEW o adn td E cost crol 13 EOI A ii 13 TOP Mi Wei ii AA AA ee 14 SCANNING INSTUCHONS ata adi raid bc 14 Chapter 2 General Settings conosca eta 16 INTOQUCION lt A odd hee he ee es 16 Barcode Programming imei aras r n 16 Command PrOGFAMMING urna rea 16 Programming Barcode Programming COMMAand FunNcCHON coocccncccnoncconccononcnonn conan ccoo nc non crac cnn 17 Use of Programming Barcodes cuota a 17 LIS Of COMMANA oa 18 Programming MOJE cresma aaa ad in PA ED a Rea OA ii aa 18 Format of COMMANA aaa a a a Taa a aa aaa aaar aaa adi rallies 18 Configuration Process FIOW iii O AO E EE GR ee 20 Default SetlingS ici it rd 21 Restore Factory Default Settings ooooconocinnccinnccnnnccconanonnncnnnn conan corno ronca rca rre 21 Operating Mode Options AA ini 22 Sa Mota e ia td int 23 Mantal ModE saen a a a aa aa a a 23 Auto Mode iii A N N A N E 24 Blink Modea a aaa eN ed Ma Bante bel 26 Sense Mode cat a dc lia a a haces 27 Gontinugus Mode 20 a A ie 30 Delayed Sense Modeiiiiorii munerne nrn A dd ee ee dee 32 Command Trigger Mode dia 33 Security OSI sust dt ns ia dt Maco a othe ae 34 Decode Beep irrita lila 35 Decode Area and Output Interval nina A ica 37 Other SOttiNGS ir aaa lana aia 38 Temporary Mitin a ia 38 Chapter 3 Inquiry Command commmmnncccnnnonnnnnnannnnnn nr 39 INTO dUCHO Meca a A A A Se ee RE A ida 39 Cha
29. decodes Plessey barcodes with either the minimum or maximum length If minimum length is same as maximum length only Plessey barcodes with that length are to be decoded The default minimum and maximum lengths are 4 characters and 255 characters respectively Set the Minimum Length 99913007 Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 MSI Plessey Restore Default Settings Scan the barcode below to restore all parameters in MSI Plessey configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99913100 Restore the Default Settings ot MSI Plessey Enable Disable MSI Plessey MSI Plessey is disabled by default 99913102 913102 99 913 101 Disable MSI Plessey Enable MSI Plessey Note If the scanner fails to identify MSI Plessey barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable MSI Plessey barcode 99900032 Exit Setup 136 9900031 99 Enter Setup 137 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for MSI Plessey To set the Code ID scan the Set Code ID for MSI Plessey barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcod
30. eee E 87 Party GHOCK evs aims ridad to ata did 88 Set Length Range for Interleaved 2 of 5 oo eeeccececeeeeeeeeeeeeeeeeeceaeeeeaeeseaeeeeaeeceaeeenaeeseaeeseaeeseaeeseaeeseaeeenaeeseaeeseaeeteeeeseeteas 89 TF Hl E E E A a A AA AAA AA iba 92 pet Code O OE 93 Deutscn diri a dd 94 Restore Default Settings icono iodo ita tia lied ee dci 94 Enable Disable Deutsched 4 cis isle ii ee E A A N E 94 pet Code A E 95 Deutsche dic cates ee ee ele a ee cies a Race vier ee ede ee 96 Restore Detfault Settings ira A a evi ee ae ea ee ed betes 96 Enable Disable Deutsche 12 0 eeesceeceseseeeeseeneeeeseeeeeeeeecenesaneeeesceeeecaaeeeeesaaeeesescacessageeeeeseaeeeseseeseeenseeeetesnseseseseesesces 96 Set COS OE 97 COOP 25 Japanese Matrix 2 0f litiasis 98 Restore Default Settings 2c nds oats Me ee i oe a eee eee 98 Enable Disable COOP iii AAA ee ee 98 Set COdG EN 99 A ON 100 Setilength Range for COOP Piscina ricota 101 Matrix 2 of 5 European Matrix 2 Of D cooooncccnnoncccnnoncccnnonnncconorncn ronca rra 102 Restore Default SENOS A Anat 102 Enable Disable Matrix 2 0f 5 piir irnn nieee ts tl da eine aed cereal 102 Set Code ID itu csc Moti nce Ree ee a ET 103 Parity COOK teat cities le eee Aa Sei eee ee 104 set Length Range for Matrix AD mitico alar 105 Ind stial2 522 05 mi a e rl gee a o ds a a a a eects 106 Restore Default Settings s curia a 106 Enable Disable IndustrialilO ui A de el eee 106 Set O 107 Ratity CheCK ierosin atanena aa
31. for Deutsche12 To set the Code ID scan the Set Code ID for Deutsche 12 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99116 99 4 0 Set Code ID for Deutsche12 Example Set the Code ID of Deutsche12 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Deutsche12 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 COOP 25 Japanese Matrix 2 of 5 Restore Default Settings Scan the barcode below to restore all parameters in COOP 25 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99911700 Restore the Default Settings of COOP25 Enable Disable COOP 25 COOP 25 is disabled by default 99911702 Enable COOP 25 99911701 Disable COOP 25 Note If the scanner fails to identify COOP 25 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable COOP 25 barcode 9900032 99 Exit Setup 98 9900031 99 Enter Setup 99 Set Code ID Code ID can only consist of one or two English letters
32. from 4 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Industrial 25 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Industrial 25 barcodes with that length are to be decoded The default minimum and maximum lengths are 6 characters and 255 characters respectively 99912007 Set the Minimum Length Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 Standard 25 Restore Default Settings Scan the barcode below to restore all parameters in Standard 25 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912200 Restore the Default Settings of Standard 25 Enable Disable Standard 25 Standard 25 is enabled by default 99912201 Enable Standard 25 Disable Standard 25 Note If the scanner fails to identify Standard 25 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Standard 25 barcode 99900032 Exit Setup 110 9900031 99 Enter Setup 111 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Standard 25 To set the Code ID scan the Set Code ID for Standard 25 barcode the numeric barcodes corre
33. is same as maximum length only Codabar barcodes with that length are to be decoded The default minimum and maximum lengths are 4 characters and 255 characters respectively 9991251 Set the Minimum Length 5 Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 Code 93 Restore Default Settings Scan the barcode below to restore all parameters in Code 93 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912600 Restore the Default Settings of Code 93 Enable Disable Code 93 Code 93 is enabled by default 99912601 Enable Code 93 Disable Code 93 Note If the scanner fails to identify Code 93 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Code 93 barcode 99900032 Exit Setup 124 9900031 99 Enter Setup 125 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Code 93 To set the Code ID scan the Set Code ID for Code 93 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99 991261 0 Set Code ID for Code 93 Example Set the Code ID of Code 93 to p its hexadecimal value is 0x70 1 Scan the Enter Setup
34. option is enabled and the minimum length is set to 4 Matrix 2 of 5 barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 104 9900031 99 Enter Setup 105 Set Length Range for Matrix 2 of 5 The scanner can be configured to only decode Matrix 2 of 5 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 3 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Matrix 2 of 5 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Matrix 2 of 5 barcodes with that length are to be decoded The default minimum and maximum lengths are 6 characters and 255 characters respectively 99912007 Set the Minimum Length Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 Industrial 25 Restore Default Settings Scan the barcode below to restore all parameters in Industrial 25 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912100 2 Restore the Default Settings of Industrial 25 Enable Disable Industrial 25 Industrial 25 is enabled by default 99912101 Enable Industrial 25 D
35. provide customers with best services HR15 corded scanner boasts the ergonomical design that ensures easy and comfortable operation An illustrated introduction to the HR15 corded scanner is included in this chapter If you have an HR15 device at hand make good use of it to develop a better understanding of this manual This chapter is written for normal users maintenance staff and software developers Unpacking Open the package and take out HR15 corded scanner and its accessories Check to make sure everything on the packing list is present and intact If any contents are damaged or missing please keep the original package and contact your dealer immediately for after sale service Scanner Decode Power LED Decode Power LED Definitions Red The device is powered on Green Barcode is decoded successfully Fig 1 1 Data Port Data Port Fig 1 2 Data port pinout 1 factory default PIN Definition Type Description 1 NC Not connected 2 NC Not connected 3 VCC P Power 5V 4 TXD O RS 232 Output 5 RXD RS 232 Input 6 CTS Flow control signal 7 RTS O 8 GND P Ground 9 D 1 0 USB signal 10 D 1 0 Data port pinout 2 PIN Definition Type Description 1 CLK1 1 0 Keyboard clock signal 2 DATA1 1 0 Keyboard data signal 3 VCC P Power 5V 4 TXD O RS 232 Output 5 RXD RS 232 Input 6 CLK2 1 0 PC clock signal
36. section in Chapter 7 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 Parity Check A check digit is optional for Interleaved 2 of 5 and can be added as the last digit It is a calculated value used to verify the accuracy of the data By default the scanner does not transmit Interleaved 2 of 5 check digit after parity check lt No Parity Check The scanner transmits Interleaved 2 of 5 barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Interleaved 2 of 5 barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Interleaved 2 of 5 barcode as check digit Barcodes passing the check will be transmitted whereas those failing it will not be transmitted 99911203 No Parity Check 999112 05 Transmit Check Digit After Parity Check 99911204 Do Not Transmit Check Digit After Parity Check Note If the Do Not Transmit Check Digit After Parity Check option is enabled Interleaved 2 of 5 barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check optio
37. window lt Use the soft cloth to clean the window such as eyeglass cleaning cloth Do not spray any liquid on the scan window lt Clean other parts of the device with water only Note The warranty DOES NOT cover damages caused by inappropriate care and maintenance 10 Depth of Field 26 3mm Code 39 10 mil 31 5mm 26 3mm Code 39 13 mil 456mm 31 5mm Code 128 10 mil 370 5mm 31 5mm Code 128 13 mil 456mm 31 5mm_ EAN 13 10mi ________ 342mm 0 31 mm EAN 13 13mi 5 5mm Specifications Performance Light Source Image Sensor Symbologies Resolution Pitch Scan Angle Roll Skew Minimum Symbol Contrast Scan Rate Interface Physical Dimensions L x W x H Weight Indication Power Adaptor Max Current Current Working Current Standby Current Environmental Operating Temperature Storage Temperature Humidity ESD Drop IP Seal Certifications FCC Part15 Class B CE EMC Class B 620nm visible red LED CCD linear image sensor Code128 EAN 13 EAN 8 Code39 UPC A UPC E Codabar Interleaved 2 of 5 ISBN Code 93 UCC EAN 128 GS1 Databar PDF417 MicroPDF417 etc 2 4 mil 55 0 Roll and 0 Skew 30 0 Pitch and 0 Skew 75 0 Roll and 0 Pitch 30 300 scans per second RS 232 USB PS 2 113 5x 73 x 159 mm 1529 Beep and LED Output DC5V 1 5A Input AC 100 240V 50 60Hz 185mA 135mA 75mA 10 C to
38. 31 Enter Setup 0 Terminating Character Suffix Enable Disable Terminating Character Suffix A terminating character such as carriage return CR or carriage return line feed pair CRLF can only be used to mark the end of data which means nothing can be added after it By default terminating character suffix is enabled 99904111 Disable Terminating Character Suffix Enable Terminating Character Suffix 0032 9990 Exit Setup 52 99900031 Enter Setup Set Terminating Character Suffix To set a terminating character suffix scan the Set Terminating Character Suffix barcode the numeric barcodes corresponding to the hexadecimal value of a desired terminating character and the Save barcode By default terminating character 0x0D 0x0A is enabled 99904113 99904112 99904114 Terminating Character Ox0D Ox0A Example Set the terminating character to Ox0A le 2 3 4 5 Scan the Enter Setup barcode Scan the Set Terminating Character Suffix barcode Scan the numeric barcodes 0 and A See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 Scan the Exit Setup barcode If terminating character suffix is enabled after finishing the above configuration an LF character will be added after scanned data Note Under the Windows operating system you can quickly set terminating
39. 5 corded scanner through serial communication the device must enter the programming mode in such mode the device will only accept and process commands and respond accordingly You can enable the device to enter or exit the programming mode by sending the specified commands to it In the event that the device receives no data for 5 seconds it will exit the programming mode automatically Format of Command 1 Exit Setup 18 Enter the programming mode send from the Host to the scanner the scanner returns a reply of to indicate success Exit the programming mode send from the Host to the scanner the scanner returns a reply of AAAA to indicate success Receiving AAAA from the scanner when the Host did not send to it indicates the scanner has automatically exit the setup mode A command string consists of programming command and such as 99900030 If a command string is properly processed the scanner will return a reply consisting of P programming command and such as 99900030 If the scanner receives an invalid command string or fails to process a command string it will return a reply consisting of programming command and such as 99900030 If a query command is properly processed the scanner will return a reply containing P programming command and 7 as well as amp query result and For exam
40. 6 912 Set Code ID for Codabar Example Set the Code ID of Codabar to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Codabar barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 120 9900031 99 Enter Setup Parity Check A check digit is optional for Codabar and can be added as the last digit It is a calculated value used to verify the accuracy of the data By default the scanner does not run parity check lt No Parity Check The scanner transmits Codabar barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Codabar barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Codabar barcode as check digit Barcodes passing the check will be transmitted whereas those failing it will not be transmitted 999125 No Parity Check 9991250 5 Do Not Transmit Check Digit After Parity Check 04 Transmit Check Digit After Parity Check Note If the Do Not Transmit Check Digit Aft
41. 9900006 6 99900007 7 99900010 8 99900011 9 92 9990001 A 99900014 C 99900016 E 0 99900013 B 0 9990001 D 5 0 99900017 F 0 162 Save Cancel Barcodes After reading numeric barcode s you need to scan the Save barcode to save the data If you scan the wrong digit s you can either scan the Cancel the Current Settings barcode and then start the configuration all over again or scan the Delete the Last Digit barcode and then the correct digit or scan the Delete All digits barcode and then the digits you want For instance after reading the Maximum Length barcode and numeric barcodes 1 2 and 3 you scan lt gt Delete the Last Digit The last digit 3 will be removed lt gt Delete All Digits All digits 123 will be removed Cancel The maximum length configuration will be canceled And the scanner still remains ready to read programming barcode 99900023 Save Cancel 99900021 Delete the Last Digit 99 90 00 Delete All Digits 2 9 163 2 Newland Headquarters 2 ETA A RAE AR RA HL ARRENDAR 1 Soe A RH al 16 350015 rig 86 0 591 83979222 GH 86 0 591 83979208 E mail marketing nlscan com j WEB www nlscan com Newland Europe BV NATA MARAT Rolweg 25 gt 4104 AV Culemborg gt The Netherlands TEL
42. D Tech Co Ltd reserves the right to make final interpretation of the statement above FuJian Newland Auto ID Tech Co Ltd 3F Building A No 1 Rujiang Xi Rd Mawei Fuzhou Fujian P R China 350015 http www niscan com Revision History Version Description Date v1 0 Initial release December 25 2011 V1 1 Moved the Enter Exit Setup barcodes to page header and footer August 10 2012 Updates 1 Added the Timeout between Decodes Same Barcode programming V1 2 feature for the Sense and Continuous modes MARCH 19 2013 2 Added PDF417 and MicroPDF417 sample barcodes in Chapter 6 Table of Contents Revision HIStOTY A NEAR iAASSEnaa 3 Preface A O 1 IMMOOUCTION iii ie ees A eee cee eee one 1 Chapter Descriptio M e toser llar tania ratio 1 DocuUmentSet ic ela 2 Chapter Getting Started ac a c ccccccccccececsacteseccescecessecesseccssccsadneatecaesacaestece ANAA NARDARANDA A mia 3 INTOAUCION isc ba 3 UNPACKINO dora A Ai E 3 A aerae naa E S a a Ea E E E EECA CETE 4 Datta Pod E E lia 4 Gonnect IRA 5 to a Hostia A A eet eesti 6 Use USB GA Css O O 7 A O O R a E tee 7 Use PS2 Cables iii it A e E E aa be apne ae pe cede teeta 8 Remove Communication Cable AA A A cece ie hat nen dee 9 Power on Power off Sleep Reboot cccsesscceeeeeeeeeeneeeeeseaeeeeeneeeeeceaeeesceaeeeseeaeeesusaeeseccaeeescnaeesescaseeeeseaeeesseneeeessueeeesee 9 MAING AN CO toscas ada da 10 Depth ot A G cede eeaed
43. Decode Session Timeout barcode and the numeric barcodes To find the numeric Decode Session Timeout barcodes see the Digit Barcodes section in Chapter 7 9990015 O Note Decode Session Timeout 01 15 corresponding to 1s 2s 15s default in 1s increments 00 infinite 99900032 23 Exit Setup 99900031 Enter Setup Auto Mode Auto Mode Pressing the trigger activates a decode session The decode session continues until the barcode is decoded or the decode session timeout occurs default 15 seconds programmable The scanner automatically starts one session after another until you press the trigger a second time 99900111 Auto Mode 900032 99 Exit Setup 24 9900031 99 Enter Setup Decode Session Timeout This parameter sets the maximum time decode session continues during a scan attempt The default timeout is 15s To program this parameter scan the Decode Session Timeout barcode and the numeric barcodes To find the numeric barcodes see the Digit Barcodes section in Chapter 7 Note Decode Session Timeout 01 15 corresponding to 1s 2s 15s default in 1s increments 00 infinite You can also configure whether to allow rereading same barcode By default rereading same barcode is not allowed 99900155 Decode Session Timeout Disallow Rereading Same Barcode 99900157 Allow Rereading Same Barcode 5 Recalcu
44. Digit MOD10 and Do Not Transmit Check Digit options are enabled and the minimum length is set to 4 MSI Plessey barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 138 9900031 99 Enter Setup 139 Set Length Range for MSI Plessey The scanner can be configured to only decode MSI Plessey barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 3 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes MSI Plessey barcodes with either the minimum or maximum length If minimum length is same as maximum length only MSI Plessey barcodes with that length are to be decoded The default minimum and maximum lengths are 4 characters and 255 characters respectively 9913112 Set the Minimum Length 99 Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 GS1 Databar Restore Default Settings Scan the barcode below to restore all parameters in GS1 Databar configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99913200 Restore the Default Settings of GS1 Databar Enable Disable GS1 Databar GS1 Databar is enabled by default 999132
45. Enable Disable Code 11 Code 11 is disabled by default 99912701 Enable Code 11 Disable Code 11 Note If the scanner fails to identify Code 11 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Code 11 barcode 99900032 Exit Setup 128 9900031 99 Enter Setup 129 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Code 11 To set the Code ID scan the Set Code ID for Code 11 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 15 99 912 7 Set Code ID for Code 11 Example Set the Code ID of Code 11 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Code 11 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check Check digits are optional for Code 11 and can be added as the last one or two digits which are calculated values used to verify the accuracy of the data By default the scanner does not transmit check digit after parity check One Check Digit MOD11 If th
46. Exit Setup 66 99900031 Enter Setup EAN 8 Extension Disable EAN 8 Zero Extend Transmit EAN 8 barcodes as is Enable EAN 8 Zero Extend Add five leading zeros to decoded EAN 8 barcodes to extend to13 digits Convert EAN 8 to EAN 13 Add five leading zeros to decoded EAN 8 barcodes to make them compatible in format to EAN 13 barcodes 99910414 99910413 Disable EAN 8 Zero Extend Enable EAN 8 Zero Extend 99910415 91 E Convert EAN 8 to EAN 13 9 Transmit Check Digit EAN 8 is 8 digits in length with the last one as its check digit used to verify the accuracy of the data By default the scanner transmits EAN 8 check digit 999104 Transmit EAN 8 Check Digit 03 Do Not Transmit EAN 8 Check Digit 99900032 67 Exit Setup 99900031 Enter Setup 0 EAN 13 Restore Default Settings Scan the barcode below to restore all parameters in EAN 13 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99910500 Restore the Default Settings of EAN 13 Enable Disable EAN 13 EAN 13 is enabled by default 99910502 Enable EAN 13 99910501 Disable EAN 13 Note If the scanner fails to identify EAN 13 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable EAN 13
47. Manual Mode Decode Session Timeout 15 seconds a A 1 15sec Timeout between Decodes 1 second 00 15 0 7 5sec Sensitivity High Sensibility Applicable to the Sense mode Security Level 1 Decode Beep Medium Pitched Loud Beep 150ms Beep notification after good decode O Sanoties per Sed Read One Barcode Nearest to the Center Per Scan Output Interval Oms Auto Mode Disabled Reread Same Barcode Continuous Mode Enabled Sense Mode Enabled Timeout between Decodes Same Barcode 1 6 seconds 0 120 0 12 0s 127 Infinite For the Continuous and Sense modes only Recalculate Timeout After Good Read Enabled Applicable to the Auto mode Communication Settings Baud Rate 9600bps 151 Parameter Default Remark Parity Check None Stop Bit 1 bit Flow Control None Data Bits 8 bits USB HID KBW Enabled Keyboard Layout 1 US English Inter Character Delay Oms 00 15 0 75ms Convert Case No Case Conversion Num Lock Off Data Formatting Prefix Sequence Code ID Custom AIM ID AIM ID Prefix Disabled Code ID Prefix Disabled 1 or 2 English letters Custom Prefix Disabled Max length 11 characters Custom Suffix Disabled Max length 11 characters Terminating Character Suffix Enabled Terminating Character 0x0D 0x0A Symbologies Code128 Code 128 Enabled Maximum Length 255 Minmum Length 1 UCC EAN 128 UCC EAN 128 Enabled
48. N 13 with Addon E3 ISSN X0 ISBN X0 UPC E EO UPC E with Addon E3 UPC A EO UPC A with Addon E3 Interleaved 2 of 5 lm 0 1 3 ITF 6 lm 1 3 ITF 14 lm 1 3 Deutsche 14 X0 Deutsche 12 X0 COOP 25 Japanese Matrix 2 of 5 xo Matrix 2 of 5 European Matrix 2 of 5 xo Industrial 25 S0 Standard 25 RO Code 39 JAm 0 1 3 4 5 7 Codabar Fm 0 2 4 Code 93 GO Code 11 Hm 0 1 3 Plessey PO MSI Plessey Mm 0 1 GS1 Databar e0 PDF417 Lm 0 1 2 MicroPDF417 Lm 3 4 5 Note m represents the AIM modifier character Refer to ISO IEC 15424 2008 Information technology Automatic identification and data capture techniques Data Carrier Identifiers including Symbology Identifiers for AIM modifier character details 159 Code ID Table Barcode Code 128 Code ID UCC EAN 128 AIM 128 ISBT 128 EAN 8 g EAN 13 ISSN ISBN UPC E UPC A Interleaved 2 of 5 ITF 6 ITF 14 Deutsche 14 Deutsche 12 COOP 25 Japanese Matrix 2 of 5 Matrix 2 of 5 European Matrix 2 of 5 Industrial 25 Standard 25 Code 39 Codabar Code 93 Code 11 Plessey MSI Plessey GS1 Databar PDF417 MicroPDF417 160 Digit Barcodes After scanning numeric barcode s you need to scan the Save barcode on the next page to save the data 0 9 161 99900000 0 99900001 1 99900002 2 99900003 3 99900004 4 99900005 5 9
49. a Aaaa aaa eae Rea 124 set Code ID ista a ii ii a a a a aAa Ne 125 Parity CheOcka cir ia aa alada 126 Set Length Range for Code 9B scceessccesseesscecesceneneeeesceneeeeeeeneneeeeaenenaeeceesenaeeceeeeneeesaeneeeeseaeseneeeseaeeenesecsaaeenenees 127 A O O AO 128 Restore Default Setting renens nisni da a ees ev a ea 128 Enable Disable Code Mii ii ai ai de 128 O A NAO 129 A AE A E AA A 130 Set Length Range for Code 11 wise ina anaa e Sanity ee aa a a nee Mg doer 131 PIOSSOY iaa a a T 132 Restore Default SettigS 0 0 ia 132 is A A O 132 Set Code Div tacita tds a ae tia 133 Parity A DLE e ive coil E ida deidad debida A e 134 SetiLength Range for Pless Yi ac 135 SS A O ET 136 Restore Default Settings taras ld pisar ata 136 Enable Disable MSI Pl SS6Y c iia ata 136 SetCod Dicta A A ti 137 O O E 138 S t Length Range for MSI Plossey cc a ra lanas shee 139 GStiDatabara iia Ea a eh CE EOL dd aaa pds 140 Restore Default Settings oia a hele elle 140 Enable Disable GS 1 Databat iii di 140 Set Code Dicta a A AA A AAA tie 141 PORFA I ESE EE A A O feet ea Nate ttt E E o oe ee 142 Restore Default Settings comodas id daa 142 Enable Disable PDF4 7 ici di ai ae 142 S t Code Diva A A A A ADA AAA 143 setiLength Range for PDEA U7 carlo ii da a 144 Sample Barcodes cau a ee eka dee a il diez 145 Micro PDF Tic e Beads eat Ts ee ee cs eae ie eee eee gee ae et 146 Restore Default Settings voii a stl ede te eae 146 Enable Disabl
50. abled 154 Parameter Default Remark Check Digit Do not transmit Maximum Length 255 Minimum Length 6 Min length supported 5 ITF 6 ITF 6 Disabled Check Digit Do not transmit ITF 14 ITF 14 Disabled Check Digit Do not transmit Deutshe 14 Deutshe 14 Disabled Check Digit Do not transmit Deutshe 12 Deutshe 12 Disabled Check Digit Do not transmit COOP25 JapaneseMatrix 2 of 5 COOP 25 Disabled Parity Check Disabled Check Digit Do not transmit Maximum Length 255 Minimum Length 6 Min length supported 3 Matrix 2 of 5 European Matrix 2 of 5 Matrix 2 of 5 Enabled Parity Check Disabled 155 Parameter Default Remark Check Digit Do not transmit Maximum Length 255 Minimum Length 6 Min length supported 3 Industrial 25 Industrial 25 Enabled Parity Check Disabled Check Digit Do not transmit Maximum Length 255 Minimum Length 6 Min length supported 4 Standard 25 Standard 25 Enabled Parity Check Disabled Check Digit Do not transmit Maximum Length 255 Minimum Length 6 Min length supported 4 Code 39 Code 39 Enabled Parity Check Disabled Check Digit Do not transmit Start Stop Character Transmit Code 39 Full ASCII Enabled Maximum Length 255 Min length supported 4 including Minimum Length 4 start s
51. al value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for UCC EAN 128 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 58 9900031 99 Enter Setup Set Length Range for UCC EAN 128 The scanner can be configured to only decode UCC EAN 128 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 1 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes UCC EAN 128 barcodes with either the minimum or maximum length If minimum length is same as maximum length only UCC EAN 128 barcodes with that length are to be decoded The default minimum and maximum lengths are 1 character and 255 characters respectively 9910104 Set the Minimum Length 99 Set the Maximum Length Example Set the scanner to decode UCC EAN 128 barcodes containing between 8 and 12 characters 1 Scan the Enter Setup barcode 2 Scan the Set the Minimum Length barcode 3 Scan the numeric barcode 8 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Set
52. an attempt The higher the security level the lower the error rate and decoding efficiency By default security is set to be level 1 99900122 Set Security Level to 1 Set Security Level to 3 99900123 Set Security Level to 2 Set Security Level to 4 0032 9990 Exit Setup 34 9900031 99 Enter Setup Decode Beep By default the scanner emits a medium pitched loud beep that lasts 150ms after good decode 99900130 Do Not Beep After Good Decode 99900131 High Pitched Loud Beep 99900132 High Pitched Medium Loud Beep 99900133 High Pitched Low Beep 99900134 Medium Pitched Loud Beep 35 99900135 90 Medium Pitched Medium Loud Beep 99900136 Medium Pitched Low Beep 99900137 Low Pitched Loud Beep 140 99900 Low Pitched Medium Loud Beep 99900141 Low Pitched Low Beep 99900032 Exit Setup 99900031 Enter Setup 99900142 99900144 Set Beep Length to 50ms 99900143 Set Beep Length to 100ms 0032 9990 Exit Setup 36 9900031 99 Enter Setup Decode Area and Output Interval You can set the number of barcodes allowed to be read per scan By default the Read One Barcode Nearest to the Center Per Scan option is enabled You can also set the decoded data output interval By default output interval is Oms 99904402 Read 2 Barcodes Per Scan
53. and the stop characters You can choose whether or not to transmit the start stop characters by scanning the appropriate barcode below By default the scanner transmits the start stop characters 99912406 Transmit Start Stop Character Do not Transmit Start Stop Character Enable Disable Code 39 Full ASCII You can configure your scanner to identify all ASCII characters by scanning the appropriate barcode below By default the scanner is able to read all ASCII characters Enable Code 39 Full ASCII 99912411 Disable Code 39 Full ASCII 9900032 99 117 Exit Setup 99900031 Enter Setup 0 Set Length Range for Code 39 The scanner can be configured to only decode Code 39 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 4 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Code 39 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Code 39 barcodes with that length are to be decoded The default minimum and maximum lengths are 4 characters and 255 characters respectively 99912413 Set the Minimum Length Set the Maximum Length Example Set the scanner to decode Code 39 barcodes containing between 8 and 12 characters 1 Scan the Enter Setup
54. ave barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Set the Maximum Length barcode 6 Scan the numeric barcodes 1 and 2 7 Scan the Save barcode 8 Scan the Exit Setup barcode 9900032 99 Exit Setup 56 9900031 99 Enter Setup UCC EAN 128 Restore Default Settings Scan the barcode below to restore all parameters in UCC EAN 128 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99910100 Restore the Default Settings of UCC EAN 128 Enable Disable UCC EAN 128 UCC EAN 128 is enabled by default 99910102 Enable UCC EAN 128 01 999101 Disable UCC EAN 128 Note If the scanner fails to identify UCC EAN 128 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable UCC EAN 128 barcode 99900032 57 Exit Setup 99900031 Enter Setup 0 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for UCC EAN 128 To set the Code ID scan the Set Code ID for UCC EAN 128 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99910105 9 Set Code ID for UCC EAN 128 Example Set the Code ID of UCC EAN 128 to p its hexadecim
55. barcode 2 Scan the Set the Minimum Length barcode 3 Scan the numeric barcode 8 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Set the Maximum Length barcode 6 Scan the numeric barcode 1 7 Scan the numeric barcode 2 8 Scan the Save barcode 9 Scan the Exit Setup barcode 99900032 Exit Setup 118 9900031 99 Enter Setup Codabar Restore Default Settings Scan the barcode below to restore all parameters in Codabar configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912500 Restore the Default Settings of Codabar Enable Disable Codabar Codabar is enabled by default 99912501 Enable Codabar Disable Codabar Note If the scanner fails to identify Codabar barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Codabar barcode 9900032 99 119 Exit Setup 99900031 Enter Setup 0 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Codabar To set the Code ID scan the Set Code ID for Codabar barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 9991251
56. character suffix to OxOD or 0x0D 0x0A by scanning the appropriate barcode above 53 99900032 Exit Setup 99900031 Enter Setup Chapter 6 Symbologies Introduction Every symbology barcode type has its own unique attributes This chapter provides programming barcodes for configuring the scanner so that it can identify various barcode symbologies It is recommended to disable those that are rarely used to increase the efficiency of the scanner Code 128 Restore Default Settings Scan the barcode below to restore all parameters in Code 128 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99910000 Restore the Default Settings of Code 128 Enable Disable Code 128 Code 128 is enabled by default 99910001 Enable Code 128 Disable Code 128 Note If the scanner fails to identify Code 128 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Code 128 barcode 99900032 Exit Setup 54 9900031 99 Enter Setup 55 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Code 128 To set the Code ID scan the Set Code ID for Code 128 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 5
57. d On Code A UPC A barcode can be augmented with a two digit add on code to form a new one 99911106 Disable 2 Digit Add On Code 999111 91 Decode UPC A 2 Digit Add On Code Only Enable 2 Digit Add On Code 07 Note Disable 2 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard UPC A barcodes lt Enable 2 Digit Add On Code The scanner decodes a mix of UPC A barcodes with and without 2 digit add on codes Decode UPC A 2 Digit Add On Code Only The scanner only decodes new barcodes combining 2 digit add on codes 00032 9990 Exit Setup 84 85 9900031 99 Enter Setup 5 Digit Add On Code A UPC A barcode can be augmented with a five digit add on code to form a new one 99911110 Disable 5 Digit Add On Code 99911112 91 1 99911111 Enable 5 Digit Add On Code Decode UPC A 5 Digit Add On Code Only Note Disable 5 Digit Add On Code The scanner only decodes the main part when scanning a new barcode It can also decode standard UPC A barcodes lt Enable 5 Digit Add On Code The scanner decodes a mix of UPC A barcodes with and without 5 digit add on codes Decode UPC A 5 Digit Add On Code Only The scanner only decodes new barcodes combining 5 digit add on codes 99900032 Exit Setup 99900031 Enter Setup 0 Interleaved 2 of 5 Re
58. e 99131 99 3 Set Code ID for MSI Plessey 1 Example Set the Code ID of MSI Plessey to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for MSI Plessey barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check Check digits are optional for MSI Plessey and can be added as the last one or two digits which are calculated values used to verify the accuracy of the data By default the scanner does not transmit check digit after parity check One Check Digit MOD10 If the No Parity Check option is enabled the scanner transmits MSI Plessey barcodes as is 99913103 No Parity Check 999131 05 Two Check Digits MOD10 MOD10 99913107 Do Not Transmit Check Digit 99913104 One Check Digit MOD10 999131 06 Two Check Digits MOD10 MOD11 99913110 Transmit Check Digit Note If the scanner enables one type of parity check and the Do Not Transmit Check Digit option MSI Plessey barcodes with a length that is less than the configured minimum length after having the check digit s excluded will not be decoded For example when the One Check
59. e MicroPDF4 17 icc csecccccscscedessaceesessascagdaaessapessansagdasaseaaciacgeagdesassiaesangsuaceanssaneasascagdeaeseiseusaseapaseiediessase 146 Set Code Dicc trat ns E is wade 147 Set Length Range for MicroPDF417 eeceesceeesceceseeeeneeeeeeeteaeeeseeensaeeeaaeesaaeeesaeessaeeesaeesaeeesaeesaeeeaaeeseaeeesaeeseaeeeatens 148 Satnple Barcodes i tdcte are he Aleta A ee AA E 149 Chapter 7 Append ixin2 as 151 Default Parameters Tabl8 oooocoinionnnonnononocnoncononnoncononnoncononnnnno non nnn corner encon enn nn non nn T nn nn nan nn corners cores rnnnrenrinnnnnos 151 AIMID Table 400 3 e o 159 Code D Table iii A A A ae de ie dae 160 DIG It BarCOdes A NN 161 Save Cancel Barcode Sisi ees cecsce tied ies erae ora eT eara td ld bs ees 163 Introduction This manual provides detailed instructions for setting up and using the NLS HR15 series corded 1D barcode scanner NLS HR1550 30 hereinafter referred to as HR15 corded scanner or the scanner Chapter Description Chapter 1 Getting Started This chapter gives a general description of HR15 corded scanner including its technical parameters Chapter 2 General Settings This chapter introduces two methods to configure the HR15 corded scanner barcode programming and command programming lt Chapter 3 Inquiry Command This chapter describes how to obtain the information of HR15 corded scanner by scanning programming barcodes Chapter 4 Communication Se
60. e ID of Deutsche14 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Deutsche14 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 Deutsche 12 Restore Default Settings Scan the barcode below to restore all parameters in Deutsche12 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99911600 Restore the Default Settings of Deutsche12 Enable Disable Deutsche 12 Deutsche12 is disabled by default 99911602 91 Enable Deutsche12 But Do Not Transmit Check Digit 99911603 Enable Deutsche12 and Transmit Check Digit 99911601 91 Disable Deutsche12 Note lt is advised not to enable Deutsche 12 unless necessary because Deutsche 12 ITF 12 and Interleaved 2 of 5 use the same encoding method and enabling them at the same time can easily cause confusion with each other when decoding 9900032 99 Exit Setup 96 9900031 99 Enter Setup 97 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID
61. e No Parity Check option is enabled the scanner transmits Code 11 barcodes as is 99912703 No Parity Check 9912705 99912 Two Check Digits MOD11 MOD11 999127 9912707 One Check Digit MOD11 Len lt 10 Two Check Digits MOD11 MOD11 Len gt 10 99912711 Do Not Transmit Check Digit 99912704 91270 One Check Digit MOD11 9127 99912706 Two Check Digits MOD11 MOD9 999127 912710 One Check Digit MOD11 Len lt 10 1 Two Check Digits MOD11 MOD9 Len gt 10 99912712 Transmit Check Digit Note If the scanner enables one type of parity check and the Do Not Transmit Check Digit option Code 11 barcodes with a length that is less than the configured minimum length after having the check digit s excluded will not be decoded For example when the One Check Digit MOD11 and Do Not Transmit Check Digit options are enabled and the minimum length is set to 4 Code 11 barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 130 99900031 Enter Setup Set Length Range for Code 11 The scanner can be configured to only decode Code 11 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 3 to 255 characters If minimum length is
62. e configured minimum length after having the two check digits excluded will not be decoded For example when the Do Not Transmit Check Digits After Parity Check option is enabled and the minimum length is set to 4 Code 93 barcodes with a total length of 4 characters including the two check digits cannot be read 99900032 Exit Setup 126 9900031 99 Enter Setup 127 Set Length Range for Code 93 The scanner can be configured to only decode Code 93 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 1 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Code 93 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Code 93 barcodes with that length are to be decoded The default minimum and maximum lengths are 2 characters and 255 characters respectively 99912607 Set the Minimum Length Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 Code 11 Restore Default Settings Scan the barcode below to restore all parameters in Code 11 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912700 Restore the Default Settings of Code 11
63. efault Settings of MicroPDF417 Enable Disable MicroPDF417 MicroPDF417 is disabled by default 99921101 Enable MicroPDF417 Disable MicroPDF417 Note Ifthe scanner fails to identify MicroPDF417 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable MicroPDF417 barcode Maximum length supported 366 bytes 99900032 Exit Setup 146 9900031 99 Enter Setup 147 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for MicroPDF417 To set the Code ID scan the Set Code ID for MicroPDF417 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99921115 Set Code ID for MicroPDF417 Example Set the Code ID of MicroPDF417 to p its hexadecimal value is 0x70 1 2 Scan the Enter Setup barcode Scan the Set Code ID for MicroPDF417 barcode Scan the programming barcodes for 7 and 0 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 Scan the Exit Setup barcode 9900032 99 3 Exit Setup 99900031 Enter Setup 0 Set Length Range for MicroPDF417 The scanner can be configured to only decode MicroPDF417 barcodes with lengths that fall between inclusive the minimum and
64. er 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 Deutsche 14 Restore Default Settings Scan the barcode below to restore all parameters in Deutsche14 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99911500 Restore the Default Settings of Deutsche14 Enable Disable Deutsche14 Deutsche14 is disabled by default 99911501 91 Enable Deutsche14 But Do Not Transmit Check Digit 99911503 Enable Deutsche14 and Transmit Check Digit Disable Deutsche14 Note lt is advised not to enable Deutsche 14 unless necessary because Deutsche 14 ITF 14 and Interleaved 2 of 5 use the same encoding method and enabling them at the same time can easily cause confusion with each other when decoding 9900032 99 Exit Setup 94 9900031 99 Enter Setup 95 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Deutsche14 To set the Code ID scan the Set Code ID for Deutsche14 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99115 99 4 0 Set Code ID for Deutsche14 Example Set the Cod
65. er Parity Check option is enabled Codabar barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check option is enabled and the minimum length is set to 4 Codabar barcodes with a total length of 4 characters including the check digit cannot be read 121 Exit Setup 99000 99 9 3 99900031 Enter Setup 0 Start Stop Character By default the scanner transmits start stop characters which are in the form of ABCD ABCP 99912506 Do not Transmit Start Stop Character 99912510 ABCD ABCD As the Start Stop Character 9991251 9 abcd abcd As the Start Stop Character 99900032 Exit Setup 99912507 Transmit Start Stop Character 99912511 ABCD TN E As the Start Stop Character 99912513 abcd tn e As the Start Stop Character 122 9900031 99 Enter Setup 123 Set Length Range for Codabar The scanner can be configured to only decode Codabar barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 2 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Codabar barcodes with either the minimum or maximum length If minimum length
66. ession Timeout 01 15 corresponding to 2s 4s 30s in 2s increments 00 infinite Timeout between Decodes Same Barcode 00 15 corresponding to Os 0 2s 3s in 0 2s increments 99900151 Decode Session Timeout Timeout between Decodes Same Barcode 9900032 99 Exit Setup 32 99900031 Enter Setup Command Trigger Mode Command Trigger Mode The scanner activates a decode session when receiving the command string of 99900035 or scanning the Start Trigger Simulation barcode The decode session continues until the barcode is decoded or the scanner receives the command string of 99900036 or scans the Stop Trigger Simulation barcode If the scanner receives the command string of 99900036 or scans the Stop Trigger Simulation barcode during a decode session it will stop the decode session and send a 2 character message e g OA or OX to the host device to indicate decoding failure Command Trigger Mode 99900116 90 99900036 Start Trigger Simulation Stop Trigger Simulation You can define a no read message to be sent to the host device when the scanner in the Command Trigger mode fails to 99 00 9042 decode a barcode Define a No Read Message 99900032 33 Exit Setup 99900031 Enter Setup 0 Security Setup This parameter specifies the number of times to decode a barcode during a sc
67. f the scanner fails to identify Plessey barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Plessey barcode 99900032 Exit Setup 132 9900031 99 Enter Setup 133 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Plessey To set the Code ID scan the Set Code ID for Plessey barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode Set Code ID for Plessey 99 913010 Example Set the Code ID of Plessey to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Plessey barcode 3 Scan the programming barcodes for 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check Check digits are optional for Plessey and can be added as the last two digits which are calculated values used to verify the accuracy of the data By default the scanner does not transmit check digits after parity check lt No Parity Check The scanner transmits Plessey barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run parity checks using t
68. git Add On COS caviar dd 70 5 Digit Add On GOGe cit cio cia in a did idad 71 Ni A A A 72 Restore Defaut S eNOS id fate O D Aa AA A ER 72 Enable Disable ISSN aic c tn ech hee ee ee id eat ee ahr ace 72 Set Code Divina sk MAR A dices hai Beene nal digi ted on eee a et Ra ee 73 ISBN cuina A ts ee ee 74 Restore Default Settings 2 Ao didas 74 Enable Disable ISBN uo he dh alee eles io nate eee 74 Set lSBN Formatve t 4 2hc itt ed ees ed i pt A Lo ee tole paa 75 Set Code Divina veh ee eee a a 75 UPA BE tao cess 76 Restore De tault Settings suicidas lr diets ands Ian iio leido laa 76 Enable Disable UPCTE 30d 76 Transmit Check Didllticosiin aiii di A le ee eee 77 set Code O ARE 77 2 Digit Add On COA E cistitis dde dea Aree 78 5 Digit Add On Code iio Misc nd een i edie ia 79 Transmit System Character Ud abi decos 80 UPCG E EXteNSION ta E AEE ATATA T AAA 80 UPA a O cole on A ale sath o N dd 81 Restore Default Settings circa dansa paa 81 Enable Disable UP CA cti da eee 81 SOt COAG ID EEE eh sales sea valeceadoes E sat adias Shaactbansetedaevaiecag dosessdeessansaddcantsduaascsaasdeavsedsusidact AA 82 Transmit Check Digilessen resida tt tete 83 Transmit Preamble Character Onai a e cba ga 83 2 Digit Add On COd6 iii ee es ee es eet dd ee eee tic 84 5 DigitC ADG On Goddess 85 Interleaved 2 Oricon ad apio eet a tonnes 86 Restore Default Settings ici 86 Enable Disable Interleaved 2 Of 5 oooocccoconcccnonnocicnonancnnno cnn narra 86 SOL COS ID EA
69. he Default Parameters Table section in Chapter 7 99911000 Restore the Default Settings of UPC E Enable Disable UPC E UPC E is enabled by default 999110 Enable UPC E 01 Disable UPC E Note If the scanner fails to identify UPC E barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable UPC E barcode 0032 9990 Exit Setup 76 9900031 99 Enter Setup Transmit Check Digit UPC E is 8 digits in length with the last one as its check digit used to verify the accuracy of the data By default the scanner transmits UPC E check digit 99911004 Transmit UPC E Check Digit 91 99911003 Do Not Transmit UPC E Check Digit Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for UPC E To set the Code ID scan the Set Code ID for UPC E barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99911020 Set Code ID for UPC E Example Set the Code ID of UPC E to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for UPC E barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit
70. he Exit Setup barcode 9900032 99 Exit Setup 62 9900031 99 Enter Setup EAN 8 Restore Default Settings Scan the barcode below to restore all parameters in EAN 8 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99910400 Restore the Default Settings of EAN 8 Enable Disable EAN 8 EAN 8 is enabled by default 999104 Enable EAN 8 01 Disable EAN 8 Note If the scanner fails to identify EAN 8 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable EAN 8 barcode 99900032 63 Exit Setup 99900031 Enter Setup 0 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for EAN 8 To set the Code ID scan the Set Code ID for EAN 8 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 9991 0 416 Set Code ID for EAN 8 Example Set the Code ID of EAN 8 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for EAN 8 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5
71. he last two digits of Plessey barcode as check digits Barcodes passing the checks will be transmitted except the last two digits whereas those failing them will not be transmitted Transmit Check Digit After Parity Check The scanner will run parity checks using the last two digits of Plessey barcode as check digits Barcodes passing the checks will be transmitted whereas those failing them will not be transmitted 999130 No Parity Check 04 Transmit Check Digit After Parity Check 999130 Do Not Transmit Check Digit After Parity Check 05 Note If the Do Not Transmit Check Digit After Parity Check option is enabled Plessey barcodes with a length that is less than the configured minimum length after having the check digits excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check option is enabled and the minimum length is set to 4 Plessey barcodes with a total length of 4 characters including the check digits cannot be read 99900032 Exit Setup 134 9900031 99 Enter Setup 135 Set Length Range for Plessey The scanner can be configured to only decode Plessey barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 4 to 255 characters If minimum length is set to be greater than maximum length the scanner only
72. ings of ITF 6 Enable ITF 6 But Do Not Transmit Check Digit 99911302 Disable ITF 6 1303 Enable ITF 6 and Transmit Check Digit Note An example of the ITF 6 priority principle when ITF 6 is enabled and Interleaved 2 of 5 is disabled the scanner only decodes Interleaved 2 of 5 barcodes with a length of 6 characters and the last character as the check character 99900032 Exit Setup 90 99900031 Enter Setup 91 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for ITF 6 To set the Code ID scan the Set Code ID for ITF 6 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99911304 Set Code ID for ITF 6 1 Example Set the Code ID of ITF 6 to p its hexadecimal value is 0x70 1 2 Scan the Enter Setup barcode Scan the Set Code ID for ITF 6 barcode Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 ITF 14 ITF 14 is a special kind of Interleaved 2 of 5 with a length of 14 characters and the last character as the check character By default ITF 14
73. is disabled ITF 14 priority principle For the Interleaved 2 of 5 barcodes with a length of 14 characters and the last character as the check character the ITF 14 configurations shall take precedence over the Interleaved 2 of 5 settings 911402 Restore the Default Settings of ITF 14 99 Enable ITF 14 But Do Not Transmit Check Digit 99911403 Disable ITF 14 14 Enable ITF 14 and Transmit Check Digit Note An example of the ITF 14 priority principle when ITF 14 is enabled and Interleaved 2 of 5 is disabled the scanner only decodes Interleaved 2 of 5 barcodes with a length of 14 characters and the last character as the check character In the events that the ITF 14 configuration clashes with the Deutsche14 settings the former shall prevail 99900032 Exit Setup 92 9900031 99 Enter Setup 93 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for ITF 14 To set the Code ID scan the Set Code ID for ITF 14 barcode the numeric barcodes for the hexadecimal value of a desired ID and the Save barcode 99911404 Set Code ID for ITF 14 Example Set the Code ID of ITF 14 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for ITF 14 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapt
74. isable Industrial 25 Note If the scanner fails to identify Industrial 25 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Industrial 25 barcode 99900032 Exit Setup 106 9900031 99 Enter Setup 107 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Industrial 25 To set the Code ID scan the Set Code ID for Industrial 25 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 9912110 99 Set Code ID for Industrial 25 Example Set the Code ID of Industrial 25 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Industrial 25 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check A check digit is optional for Industrial 25 and can be added as the last digit lt is a calculated value used to verify the accuracy of the data By default the scanner transmits check digit after parity check lt No Parity Check The scanner transmits Industrial 25 barcodes as is Do Not Transmit Check Digit Af
75. it it td 108 Set Length Range for Industrial 25 ooooocinccccnnccinnccnonccnoncnconononnncnonononnn ccoo a rra crono O a enema nn aa an ae 109 Standard ii A AA ee eee ie E 110 Restore Default Settings iii 110 Enable Disable Standard 2D cocino Ii alada creda ey een A de eee 110 Set Code Diis tert nti ita ie dee iaa ai ae 111 Parity Check cui A A A A Ad 112 Set Length Range for Standard 25 00 0 e a ea a a aa aa a ae aa Ea aa E Ea aE A AAO AAE ENEE TTR E O ATE EPEA Ae SAAE ERS 113 Eoo SD E NN 114 Restore Default Settings iii ii a ia 114 Enable Disable Gode 39 ta 114 Set Code D AEE E E id e deal 115 Parity Check cio o A AA AA tt 116 Transmit Start StopCharacte ts r a cesaclesalcasdiesskesaddciatcecsadetaddsiahdesichasiajdsaatsaaci dstajaedassantenincagdcearsacdssistaagetaseiataedas 117 Enable Disable G de 39 Full ASGII sicsceseesiisce seesaw deere tea emai di ib 117 SetLength Range for Gode 39 miii a ea eed aa aaa 118 A ia eee Ai et i ee ee 119 Restore Default Settings o ae E RE 119 Enable Disable Codabat senna ess ee ler a eked es 119 set Code Divinas a eed BA a teen ed ee ead ii eS Se a 120 Parity Checkis thas ssc Bibi A atte Re A A ee a a 121 sltant Stop Character A A T AE T 122 Set Length Range for Godapat sssri akeri eign teuen e eeta aa taa agree ih aed ain 123 A A AE AEREE L EAE dl a Se oe E T E E T A 124 Restore Default Settings enico hAedan n eit ae e A edi vee 124 Enable Disable Code IB tina lila a
76. ity Check Transmit Check Digit After Parity Check Note If the Do Not Transmit Check Digit After Parity Check option is enabled Standard 25 barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check option is enabled and the minimum length is set to 4 Standard 25 barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 112 9900031 99 Enter Setup 113 Set Length Range for Standard 25 The scanner can be configured to only decode Standard 25 barcodes with lengihs that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 4 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Standard 25 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Standard 25 barcodes with that length are to be decoded The default minimum and maximum lengths are 6 characters and 255 characters respectively 9912206 99 912207 Set the Minimum Length 99912207 Set the Maximum Length 9900032 99 Exit Setup 99900031 Enter Setup 0 Code 39 Restore Default Settings Scan the barcode below to resto
77. k on the PS 2 cable If necessary plug the keyboard into the PS 2 female socket on the cable PON gt Remove Communication Cable Fig 1 6 Get an appropriate needle or a straightened paper clip and then follow the steps below Po nN gt Disconnect the power adapter from mains and the scanner if there is one Insert the needle into the disassemble hole Fig 1 6 Pull out the cable slowly from the scanner while pressing the needle in Then remove the needle Disconnect the cable from the Host Power on Power off Sleep Reboot Power on the scanner Connect the scanner to a host device Then the scanner will be turned on and automatically go into sleep mode Power off the scanner There are four ways to turn off the scanner gt gt gt Remove the cable from the scanner Remove the cable from the host device Disconnect the power adapter from mains or the scanner Scan the Power Off barcode See the Operating Mode Options section in Chapter 2 Enter the sleep mode If no operation is performed on the scanner for some time the scanner will automatically enter the sleep state Reboot the scanner If the scanner stops responding to input or runs abnormally disconnect the scanner from the host device and then reconnect it Maintenance lt The scan window should be kept clean lt Do not scratch the scan window of the device lt Use soft brush to remove the stain from the scan
78. late Timeout After Good Read Allow Rereading Same Barcode This allows the scanner to reread the same barcode that has been decoded in the previous session Disallow Rereading Same Barcode This protects against accidental rereads of the same barcode If the barcode being scanned is identical with the one previously scanned the decode session will suspend until a different barcode comes up lt Recalculate Timeout After Good Read The decode session timeout restarts after a good read 99900032 25 Exit Setup 99900031 Enter Setup 0 Blink Mode Blink Mode The scanner automatically activates a decode session The decode session continues until the barcode is decoded or the decode session timeout occurs 100ms non programmable When a decode session is completed the scanner waits until the timeout between decodes occurs default 1s programmable and then starts next session The scanner continues to work in this pattern Pressing the trigger can also activate a decode session holding down the trigger can suspend decode session Timeout between Decodes This parameter sets the time period between the end of one decode session and the start of next session lt is programmable in 0 5s increments from Os to 7 5s The default timeout is 1s To program this parameter scan the Timeout between Decodes barcode and the numeric barcodes Note Timeout between Decodes 00 15 corresponding to Os 0 5s 1s
79. maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 1 to 366 bytes If minimum length is set to be greater than maximum length the scanner only decodes MSI Plessey barcodes with either the minimum or maximum length If minimum length is same as maximum length only MSI Plessey barcodes with that length are to be decoded The default minimum and maximum lengths are 1 byte and 366 bytes respectively 99921104 Set the Minimum Length Set the Maximum Length 99900032 Exit Setup 148 99900031 Enter Setup Sample Barcodes When reading a MicroPDF417 barcode you need to scan it horizontally from the top bottom row of the barcode to the bottom top Apart from the influence of barcode density consecutive horizontal scans are essential for accomplishing a good read The greater the row height is the easier it is to decode a MicroPDF417 barcode Listed below are some sample barcodes 15 mil la DIA A VA 5 ACT BR ZS A 123456789012345678901 99000 99 149 Exit Setup 9 3 99900031 Enter Setup 0 A abcdefghijklmnopqrstuvwxyz 99900032 Exit Setup 150 Chapter 7 Appendix Default Parameters Table Parameter Default Remark General Settings Setup Mode Enabled Programming Barcode Data Do not send Scan Mode
80. mum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 1 to 2710 bytes If minimum length is set to be greater than maximum length the scanner only decodes MSI Plessey barcodes with either the minimum or maximum length If minimum length is same as maximum length only MSI Plessey barcodes with that length are to be decoded The default minimum and maximum lengths are 1 byte and 2710 bytes respectively 99920104 Set the Minimum Length Set the Maximum Length 99900032 Exit Setup 144 99900031 Enter Setup Sample Barcodes When reading a PDF417 barcode you need to scan it horizontally from the top bottom row of the barcode to the bottom top Apart from the influence of barcode density consecutive horizontal scans are essential for accomplishing a good read The greater the row height is the easier it is to decode a PDF417 barcode Listed below are some sample barcodes 15 mil ets DIA A sb BAA IR Fy 123456789012345678901 rental abcdefghijkImnopgrstuvwxyz 99000 99 9 3 145 Exit Setup 99900031 Enter Setup 0 MicroPDF417 Restore Default Settings Scan the barcode below to restore all parameters in PDF417 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99921100 Restore the D
81. n decodes for the same barcode It protects against accidental rereads of the same barcode It is programmable in 0 1s increments from Os to 12s If you want to stop the scanner from rereading the same barcode set this parameter to 127 The default timeout is 1 6s To program this parameter scan the Timeout between Decodes Same Barcode barcode the numeric barcode s and the 99900167 Timeout between Decodes Same Barcode Save barcode Note Timeout between Decodes Same Barcode 0 120 corresponding to Os 0 1s 1 6s default 12s in 0 1s increments 127 infinite Example Set the timeout between decodes same barcode to 5s 1 Scan the Enter Setup barcode 2 Scan the Timeout between Decodes Same Barcode barcode 3 Scan the numeric barcodes 5 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 29 Exit Setup 99900031 Enter Setup 0 Continuous Mode Continuous Mode The scanner automatically activates a decode session The decode session continues until the barcode is decoded When a decode session is completed the scanner waits until the timeout between decodes occurs and then starts next session The scanner continues to work in this pattern Same barcode cannot be reread before the timeout between decodes same barcode occurs Holdi
82. n is enabled and the minimum length is set to 6 Interleaved 2 of 5 barcodes with a total length of 6 characters including the check digit cannot be read 99900032 Exit Setup 88 9900031 99 Enter Setup 89 Set Length Range for Interleaved 2 of 5 The scanner can be configured to only decode Interleaved 2 of 5 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 5 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes Interleaved 2 of 5 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Interleaved 2 of 5 barcodes with that length are to be decoded The default minimum and maximum lengths are 6 characters and 255 characters respectively 99911207 Set the Minimum Length Set the Maximum Length 99900032 Exit Setup 99900031 Enter Setup ITF 6 ITF 6 is a special kind of Interleaved 2 of 5 with a length of 6 characters and the last character as the check character By default ITF 6 is disabled ITF 6 priority principle For the Interleaved 2 of 5 barcodes with a length of 6 characters and the last character as the check character the ITF 6 configurations shall take precedence over the Interleaved 2 of 5 settings IM Tl Restore the Default Sett
83. ncdeeeanteulaeeteeetvees 54 INTOdUCUION enhe ereere tadas ae ee te aie chee eet 54 Code Bit ei eed og a OE iia ties dad 54 Restore Default Settings 2a ated eich ae eddie ee de i a ee 54 Enable Disable Code 1285 22 iiaa a a a E a E A A aE AEA EEE eatin 54 SetCodelDrasna ns iio a lor a a 55 Setilength Range tor Code 128 iia 56 UCC EAN PB iii A A A A A ee eee TE 57 Restore Default Settings Li RRA 57 Enable Disable UCC EAN 128 oia td di cee a ne eee 57 Set Code DD iii a A A A A Sed ae 58 Set Length Range for UCC EAN 128 oooooconccccocccoocccnonccnoncnnonononnn ccoo nene cnn nene n rana r ranas 59 A sno as 3 tat 5 Te oo Matos tie Rea hath eS a We tT a 8 nto otc th ies aoa a AES sh Renee sN AC Dar neha 2 acter Dns acl ees eat Sink ao ante 60 Restore Default Settings 3s waaciud ete teen Bene etal eh ae ee ese oh eee 60 Enable Disabl AIM 4 28 c s i0h i aeiiia datehsiniak Melita dia Wit a 60 set Code Divinas tae ee et A A eet 61 set Length Range for AM 128 Ai e a aa aa a E AAE aa ano ETE ERARA 62 EAN ENEE E E E E E E tik aed ce boat aes 63 Restore Default Settings rniii noo decai A Aa hb elder ba da cod 63 Enable Disable EAN Bio AA TA 63 Seto Din lc alicia 64 2 Digit Add On GOde susi ra o Riis 65 5 Digit Add On Code iria 66 EANS8 Extenslonive tiiv cesta A eee ee 67 aeeie Eao l E A E AE 67 A E E E E EE DEE E A T E E 68 Enable Disable EAN TB A ii 68 Transmit Check Dillon ti A dd eed 69 pet E OOOO 69 2 Di
84. ng down the trigger can also activate the scanner to decode continuously but with no intervals i e timeout between decodes will be ignored 99900114 Continuous Mode 99900032 Exit Setup 30 99900031 Enter Setup Timeout between Decodes This parameter sets the time period between the end of one decode session and the start of next session lt is programmable in 0 5s increments from Os to 7 5s The default timeout is 1s To program this parameter scan the Timeout between Decodes barcode and the numeric barcodes Note Timeout between Decodes 00 15 corresponding to Os 0 5s 1s default 7 5s in 0 5s increments 99900151 Timeout between Decodes Timeout between Decodes Same Barcode This parameter sets the minimum time between decodes for the same barcode It protects against accidental rereads of the same barcode It is programmable in 0 1s increments from Os to 12s If you want to stop the scanner from rereading the same barcode set this parameter to 127 The default timeout is 1 6s To program this parameter scan the Timeout between Decodes Same Barcode barcode the numeric barcodes and the Save barcode Note Timeout between Decodes Same Barcode 0 120 corresponding to Os 0 1s 1 6s default 12s in 0 1s 99900167 Timeout between Decodes Same Barcode increments 127 infinite Example Set the timeout between decodes same barcode to 5s 1 Scan the En
85. nsmitted whereas those failing it will not be 9911704 99 No Parity Check 99 Transmit Check Digit After Parity Check 9991170 5 Do Not Transmit Check Digit After Parity Check transmitted 1 Note If the Do Not Transmit Check Digit After Parity Check option is enabled COOP 25 barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check option is enabled and the minimum length is set to 4 COOP 25 barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 100 99900031 Enter Setup Set Length Range for COOP 25 The scanner can be configured to only decode COOP 25 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 3 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes COOP 25 barcodes with either the minimum or maximum length If minimum length is same as maximum length only COOP 25 barcodes with that length are to be decoded The default minimum and maximum lengths are 6 characters and 255 characters respectively 9911706 Hil 99 Set the Minimum Length 11707 999 Set the Maximum Length 101 Exit
86. ons in Chapter 6 For the information of default Code ID see the Code ID Table section in Chapter 7 By default Code ID prefix is disabled 99904042 Disable Code ID Prefix 99904041 Enable Code ID Prefix Restore Default Code IDs 0032 9990 Exit Setup 50 9900031 99 Enter Setup Custom Suffix 51 Enable Disable Custom Suffix If custom suffix is enabled you are allowed to append to the data a user defined suffix that cannot exceed 11 characters By default custom suffix is disabled For example if barcode data is 123 and custom suffix is AB the Host will receive 123AB 99904101 Disable Custom Suffix Enable Custom Suffix Set Custom Suffix To set a custom suffix scan the Set Custom Suffix barcode the numeric barcodes corresponding to the hexadecimal value of a desired suffix and the Save barcode Note A custom suffix cannot exceed 11 characters 99904102 Set Custom Suffix Example Set the custom suffix to AGE its hexadecimal value is 0x41 0x47 0x45 1 Scan the Enter Setup barcode Scan the Set Custom Suffix barcode Scan the numeric barcodes 4 1 4 7 4 and 5 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 Scan the Enable Custom Suffix barcode 2 a F oO PL Scan the Exit Setup barcode 99900032 Exit Setup 999000
87. ple send a query command of 99900301 to get the firmware version information the Host will receive a reply of 99900301 amp Firmware v1 7 5 Decoder v1 00 023 C6 FD25430B Description In the reply Firmware v1 7 5 Decoder v1 00 023 C6 is the query result is a separator and FD25430B is the CRC32 checksum value in hexadecimal format 99900032 8 99900031 Enter Setup If a command involves parameter s they shall be combined as per the rule For example The combined commands for appending terminating character suffix OxOD CR 0x0A LF to the scanned data and saving the settings 999041 12 99900000 99900015 99900000 9990001 2 99900020 99900032 Exit Setup 99900031 Enter Setup Configuration Process Flow Send Receive WOW E 5 seconds timeout Non Programming Model Recejye anna Programming Mode Send Receive rrna Host sends a command 20000006 Process Command Receive XXXXXXXX Succeed No Query Command Receive xxxxxxxx Yes Receive IXXXXXXXX amp XXX XXX 99900032 Exit Setup 20 900031 99 Enter Setup Default Settings Restore Factory Default Settings Scanning the Reset Scanner barcode can restore the scanner to the factory default settings You may need to reset your scanner when 1 scanner is not properly configured so that it fails to decode barcodes 2
88. pter 4 Communication SettinaS ii idad iiaiaiin 40 AS 232 Mera E a id 40 Baud Rate nin a O E cid ees eee 40 Parity Check AEA E ATA T E T TT 42 Stop Bibi a e a oe e o e o io 42 Flow Controladora ar Bi ee ea e 43 Data Bitar A A AAA E r a 44 USB Ace iia E 45 USB HID KBW cto cio lt ta dt tata eee hey 45 USB COM Port Emulation itutonte ltd rele bdo laca 45 Keyboard Para Mete iii AA ee 46 Keyboard Layout sih ae air ri eA iii 46 Inter Character Delay iran it ae ieee n ei N a en eA eae 47 Convera aaa ei 47 Chapter 5 Data Formatting ic econo a ide 48 A 48 Prefi Sequence mama dades tal dt to 48 Gusto Mi Pre a a a taa ie e end a Lio A LE 49 Enable Disable Custom Pretix 20522222 Stk etek ak eae Aa Beer ats Ree ee ee a eed 49 Set Custom Prefixes nus gentan erea lbh Sc eed te lt ee 49 AIMIDPrefie 0 Ns ahs A oa PN te es ea dE Asc ees oss tN eri 2a etn ao 50 GOED Preu td a dl 50 CUSTOM SUMA A e O a 51 Enable Disable Custom SUR iaa 51 Det Custom OTE 51 Terminating haracter Suitix ch cen caida Se a ia eae 52 Enable Disable Terminating Character Suffix eccceeecceseeeeeeeeeeeeeeeeeeeseeeeeeeeseaeeesaeetaeeesaeeseaeesaeeseaeeseeeseaeeenaeeseaeeseatens 52 Set Terminating Character Sutfix ccceesceesseeseeeseneeeeeeeseaeeeeaeeseaeeeeaeeseaeesaeeseaeeeaeeceaeessaeeseaeeeaeeseaeessaeeseaeeesatessaeeeaes 53 Chapter 6 SymbDologies aes aiae aaan raae aara eaaa areae aaea aaa enaa aaa paaa saaa aaae dyscececep vane Ce
89. rcase 99902233 Invert Upper and Lower Case Characters 99900032 Exit Setup 99900031 Enter Setup Chapter 5 Data Formatting Introduction After a successful barcode reading a string containing numbers letters or symbols will be returned In real applications barcode data may be found insufficient for your needs You may wish to include additional information such as barcode type data acquisition time or delimiter in data being scanned Adding extra information to printed barcodes does not seem like a sensible solution since that will increase the barcode size and make them inflexible Instead we come up with the idea of appending prefix and suffix to the data without making any change to barcodes We will show you how to conduct the configuration in the following sections Note Customized data lt Prefix gt lt Data gt lt Suffix gt lt Terminating Character gt Prefix Sequence By default the Code ID Custom AlM ID option is enabled 99904011 Code ID Custom AlM ID Custom Code ID AIM ID 99900032 Exit Setup 48 9900031 99 Enter Setup Custom Prefix 49 Enable Disable Custom Prefix If custom prefix is enabled you are allowed to append to the data a user defined prefix that cannot exceed 11 characters By default custom prefix is disabled For example if barcode data is 123 and custom prefix is AB the Host will receive AB123 99904021
90. re all parameters in Code 39 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99912400 Restore the Default Settings of Code 39 Enable Disable Code 39 Code 39 is enabled by default 99912401 Enable Code 39 Disable Code 39 Note If the scanner fails to identify Code 39 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Code 39 barcode 99900032 Exit Setup 114 9900031 99 Enter Setup 115 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Code 39 To set the Code ID scan the Set Code ID for Code 39 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99912414 912 Set Code ID for Code 39 Example Set the Code ID of Code 39 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Code 39 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check A check digit is optional for Code 39 and
91. set to be greater than maximum length the scanner only decodes Code 11 barcodes with either the minimum or maximum length If minimum length is same as maximum length only Code 11 barcodes with that length are to be decoded The default minimum and maximum lengths are 4 characters and 255 characters respectively 9912713 9 Set the Minimum Length 99912714 Set the Maximum Length Example Set the scanner to decode Code11 barcodes containing between 8 and 12 characters 1 Scan the Enter Setup barcode 2 Scan the Set the Minimum Length barcode 3 Scan the numeric barcode 8 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Set the Maximum Length barcode 6 Scan the numeric barcode 1 7 Scan the numeric barcode 2 8 Scan the Save barcode 9 Scan the Exit Setup barcode 9900032 99 3 131 Exit Setup 99900031 Enter Setup 0 Plessey Restore Default Settings Scan the barcode below to restore all parameters in Plessey configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99913000 Restore the Default Settings of Plessey Enable Disable Plessey Plessey is disabled by default 3002 Enable Plessey 9991 3001 Disable Plessey Note I
92. sponding to the hexadecimal value of a desired ID and the Save barcode 9912210 99 Set Code ID for Standard 25 Example Set the Code ID of Standard 25 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for Standard 25 barcode 3 Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 9900032 99 Exit Setup 99900031 Enter Setup 0 Parity Check A check digit is optional for Standard 25 and can be added as the last digit lt is a calculated value used to verify the accuracy of the data By default the scanner does not run parity check lt No Parity Check The scanner transmits Standard 25 barcodes as is Do Not Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Standard 25 barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted lt Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Standard 25 barcode as check digit Barcodes passing the check will be transmitted whereas those failing it will not be transmitted 99912204 No Parity Check EAN 5 Do Not Transmit Check Digit After Par
93. store Default Settings Scan the barcode below to restore all parameters in Interleaved 2 of 5 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99911200 Restore the Default Settings of Interleaved 2 of 5 Enable Disable Interleaved 2 of 5 Interleaved 2 of 5 is enabled by default 99911201 Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 Note If the scanner fails to identify Interleaved 2 of 5 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable Interleaved 2 of 5 barcode 9900032 99 Exit Setup 86 9900031 99 Enter Setup 87 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for Interleaved 2 of 5 To set the Code ID scan the Set Code ID for Interleaved 2 of 5 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 99911210 Set Code ID for Interleaved 2 of 5 Example Set the Code ID of Interleaved 2 of 5 to p its hexadecimal value is 0x70 ile 2 Scan the Enter Setup barcode Scan the Set Code ID for Interleaved 2 of 5 barcode Scan the numeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes
94. ter Parity Check The scanner will run a parity check using the last digit of Industrial 25 barcode as check digit Barcodes passing the check will be transmitted except the last digit whereas those failing it will not be transmitted lt Transmit Check Digit After Parity Check The scanner will run a parity check using the last digit of Industrial 25 barcode as check digit Barcodes passing the check will be transmitted whereas those failing it will not be transmitted 99912103 No Parity Check 9991210 Do Not Transmit Check Digit After Parity Check oO 99 4 91210 Transmit Check Digit After Parity Check Note If the Do Not Transmit Check Digit After Parity Check option is enabled Industrial 25 barcodes with a length that is less than the configured minimum length after having the check digit excluded will not be decoded For example when the Do Not Transmit Check Digit After Parity Check option is enabled and the minimum length is set to 4 Industrial 25 barcodes with a total length of 4 characters including the check digit cannot be read 99900032 Exit Setup 108 9900031 99 Enter Setup 109 Set Length Range for Industrial 25 The scanner can be configured to only decode Industrial 25 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range
95. ter Setup barcode Scan the Timeout between Decodes Same Barcode barcode Scan the numeric barcodes 5 and 0 See the Digit Barcodes section in Chapter 7 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 a e W N Scan the Exit Setup barcode 99900032 31 Exit Setup 99900031 Enter Setup 0 Delayed Sense Mode Delayed Sense Mode The scanner automatically activates a decode session when it detects a change in ambient illumination The decode session continues until the barcode is decoded or the decode session timeout occurs When a decode session is completed the scanner waits 200ms and then starts to monitor ambient environment until it detects a change to trigger next decode session Same barcode cannot be reread before the timeout between decodes same 9990011 2 barcode occurs Delayed Sense Mode Decode Session Timeout This parameter sets the maximum time decode session continues during a scan attempt To program this parameter scan the Decode Session Timeout barcode and the numeric barcodes Timeout between Decodes Same Barcode This parameter sets the minimum time between decodes for the same barcode It protects against accidental rereads of the same barcode It is programmable in 0 2s increments from Os to 3s To program this parameter scan the Timeout between Decodes Same Barcode barcode and the numeric barcodes Note Decode S
96. the Maximum Length barcode 6 Scan the numeric barcodes 1 and 2 7 Scan the Save barcode 8 Scan the Exit Setup barcode 99900032 59 Exit Setup 99900031 Enter Setup 0 AIM 128 Restore Default Settings Scan the barcode below to restore all parameters in AIM 128 configuration to the factory default settings To find the related default settings see the Default Parameters Table section in Chapter 7 99910200 Restore the Default Settings of AIM 128 Enable Disable AIM 128 AIM 128 is disabled by default 99910202 Il Enable AlM 128 0 9991 Disable AIM 128 01 02 Note If the scanner fails to identify AIM 128 barcodes you may first try this solution by scanning the Enter Setup barcode and then Enable AIM 128 barcode 0032 9990 Exit Setup 60 9900031 99 Enter Setup 61 Set Code ID Code ID can only consist of one or two English letters See the Code ID Table section in Chapter 7 to find the default Code ID for AIM 128 To set the Code ID scan the Set Code ID for AIM 128 barcode the numeric barcodes corresponding to the hexadecimal value of a desired ID and the Save barcode 9991020 Set Code ID for AIM 128 5 Example Set the Code ID of AIM 128 to p its hexadecimal value is 0x70 1 Scan the Enter Setup barcode 2 Scan the Set Code ID for AIM 128 barcode 3 Scan the n
97. the number of bits of data transmitted per second Set the scanner s baud rate to match the Host requirements Otherwise data may not reach the Host or may reach it in distorted form The default baud rate is 9600 99902101 9600 1200 99902103 2400 4800 99902106 14400 19200 99900032 Exit Setup 40 41 99902107 38400 99902111 115200 99900031 Enter Setup 99902110 57600 99900032 Exit Setup 99900031 Enter Setup Parity Check By default the None option is enabled None 99902122 Even 99902121 Odd Stop Bit By default the 1 Stop Bit option is enabled 1 Stop Bit 99902133 2 Stop Bits 0032 9990 Exit Setup 42 99900031 Enter Setup Flow Control By default the No Flow Control option is enabled No Flow Control 99902142 CTS Flow Control RTS Flow Control 99902143 RTS_CTS Flow Control 99900032 43 Exit Setup 99900031 Enter Setup 0 Data Bit By default the 8 Data Bits option is enabled 99 902150 8 Data Bits 99902160 8 Data Bits No Parity 1 Stop Bit 99902161 8 Data Bits Even Parity 1 Stop Bit 99902162 8 Data Bits Odd Parity 1 Stop Bit 99902151 5 7 Data Bits 99902166 7 Data Bits Even Parity 1 Stop Bit 0032 9990 Exit Setup 99902163 8 Data Bits No Parity
98. top characters and check digit 156 Parameter Default Remark Codabar Codebar Enabled Parity Check Disabled Check Digit Do not transmit ABCD ABCD format Start Stop Character Transmit Maximum Length 255 Minmum Length 4 Min length supported 2 Code 93 Code 93 Enabled Parity Check Enabled Check Digit Do not transmit Maximum Length 255 Minimum Length 2 Min length supported 1 Code 11 Code 11 Disabled Check Digit Do not transmit Parity Check Enabled 1 Check Digit MOD11 Maximum Length 255 Minimum Length 4 Min length supported 3 Plessey Plessey Disabled Parity Check Enabled Check Digit Do not transmit 157 Parameter Default Remark Maximum Length 255 Minimum Length 4 Min length supported 4 MSI Plessey MSI Plessey Disabled Check Digit Do not transmit Parity Check Enabled 1 Check Digit MOD10 Maximum Length 255 Minimum Length 4 Min length supported 3 GS1 Databar GS1 Databar Enabled PDF417 PDF 417 Enabled Maximum Length 2710 Minimum Length 1 MicroPDF417 MicroPDF417 Disabled Maximum Length 366 Minimum Length 158 AIM ID Table Barcode AIM ID Possible AIM ID Parameters Code 128 CO UCC EAN 128 C1 AIM 128 C2 ISBT 128 C4 EAN 8 E4 EAN 13 JEO EA
99. ttings This chapter describes how to configure serial port parameters and USB function Chapter 5 Data Formatting This chapter describes how to use prefix and suffix to customize scanned data Chapter 6 Symbologies This chapter lists all compatible symbologies and describes how to configure the relevant parameters Chapter 7 Appendix This chapter offers default parameters tables and a bunch of frequently used programming barcodes Document Set The documentation set for the HR15 corded scanner provides information for specific user needs and includes NLS HR1550 30 Quick Start Guide NLS HR1550 30 User Guide 1D Barcode Scanner Firmware Update Utility User Guide EzSet123 Scanner Configuration Utility User Guide Describes how to get the HR15 corded scanner up and running and introduces some basic operations Describes how to use and set the HR15 corded scanner Describes how to update the firmware in 1D barcode scanners with this tool developed by Newland Describes how to configure scanners with this tool developed by Newland Chapter 1 Getting Started Introduction HR15 corded scanner is a 1D barcode scanner with excellent performance Besides all common 1D symbologies it can also read 2D stacked symbologies such as PDF417 and MicroPDF417 Based on the UIMG technology independently developed by Newland HR15 corded scanner is able to deliver rapid image acquisition and accurate decoding it can
100. umeric barcodes 7 and 0 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Exit Setup barcode 99900032 Exit Setup 99900031 Enter Setup 0 Set Length Range for AIM 128 The scanner can be configured to only decode AIM 128 barcodes with lengths that fall between inclusive the minimum and maximum lengths To accomplish it you need to set the minimum and maximum lengths Both lengths can range from 1 to 255 characters If minimum length is set to be greater than maximum length the scanner only decodes AIM 128 barcodes with either the minimum or maximum length If minimum length is same as maximum length only AIM 128 barcodes with that length are to be decoded The default minimum and maximum lengths are 1 character and 255 characters respectively 9910203 9 Set the Maximum Length 99910204 Set the Minimum Length Example Set the scanner to decode AIM128 barcodes with lengths containing between 8 and 12 characters 1 Scan the Enter Setup barcode 2 Scan the Set the Minimum Length barcode 3 Scan the numeric barcode 8 See the Digit Barcodes section in Chapter 7 4 Scan the Save barcode See the Save Cancel Barcodes section in Chapter 7 5 Scan the Set the Maximum Length barcode 6 Scan the numeric barcodes 1 and 2 7 Scan the Save barcode 8 Scan t
101. unction that can be enabled by using the programming barcode or command listed above 4 incidates factory default settings Use of Programming Barcodes Scanning the Enter Setup barcode can enable the scanner to enter the setup mode Then you can scan a number of programming barcodes to configure your scanner The HR15 corded scanner is in the setup mode by default In real application programming barcodes hardly overlap with non programming barcodes so it is unnecessary to exit the setup mode each time you finish the configuration Some functions or options may involve parameter value settings that require scanning numeric barcodes To find the numeric barcodes see the Digit Barcodes section in Chapter 7 The scanner can be configured to send or not to send programming barcode data i e programming command to the host device by scanning the appropriate barcode below By default the Do Not Send the Programming Barcode Data option is enabled Note that restarting rebooting the scanner will reset this parameter to its default value 900033 03 Send the Programming Barcode Data 99 Do Not Send the Programming Barcode Data 99900032 17 Exit Setup 990 0 031 9 Enter Setup Use of Command Based on serial port communication programming commands can be composed of printable ASCII characters 0x20 space through 0x7D y Programming Mode Before configuring the HR1
102. ut between Decodes barcode and the numeric barcodes Note Decode Session Timeout 01 15 corresponding to infinite 1s 2s 15s default in 1s increments 00 infinite Timeout between Decodes 00 15 corresponding to Os 0 5s 1s default 7 5s in 0 5s increments 99900151 Decode Session Timeout Timeout between Decodes 99900032 Exit Setup 99900031 Enter Setup 0 Sensitivity specifies the degree of acuteness of the scanner s response to changes in ambient illumination The higher the sensitivity the lower requirement in illumination change to trigger the scanner You can select an appropriate degree of sensitivity that fits the ambient environment By default High Sensitivity is enabled 99900154 High Sensitivity Low Sensitivity 99900161 Medium Sensitivity Custom Sensitivity It is recommended not to set the custom sensitivity when one of the other three options can meet your needs Note Sensitivity 00 OF the smaller the number the higher the sensitivity Example Set the sensitivity to level 5 1 Scan the Enter Setup barcode 2 Scan the Custom Sensitivity barcode 3 Scan the numeric barcodes 0 and 5 See the Digit Barcodes section in Chapter 7 4 Scan the Exit Setup barcode 99900032 Exit Setup 28 99900031 Enter Setup Timeout between Decodes Same Barcode This parameter sets the minimum time betwee

Download Pdf Manuals

Related Search

Related Contents

アクオス かんたん接続ガイドダウンロード [PDF 2.96MB]  技術内容説明書    User Manual - Full Throttle Speed Tech Support  Benutzerhandbuch / User Manual    Nuance Dragon NaturallySpeaking 13 Professional  LX-2000 Fire Pump Controller - Hubbell Industrial Controls  Compucase 6C11  User Manual  

Copyright © All rights reserved. Failed to retrieve file