User Guide - Conference Room AV Solutions
Contents
1. 11 User Guide SERIAL COMMANDS RS 232 Commands Command Query Response lt cr gt 0x0D Hex 13 Decimal 20 Fixed Address for DXW DXW will not pass through serial to other port when it sees it is a specific command intended for the DXW Command will work without address however the response will appear on both ports Please note if you are working with firmware below revision 1 21 the fixed address will not work and must be sent without the 20 Command String Format Information y port number 1 or 2 1 is HDBaseT 2 is Rear Port a baud rate 2400 4800 9600 19200 38400 57600 115200 Baud Rate Setup b bits parity stop 8N1 8E1 801 Command I20BRy a b lt cr gt Factory Default is 9600 8N1 y 1 3 1 is VGA 2 is HDMI 3 is DisplayPort z1 Released LED State R G B N R Red G Green B Blue N None z1 Pushed LED State R G B N R Red G Green B Blue N None Button LED Setup I2ZOBLy z1 z2 lt cr gt Factory Default is off for release and blue for push x 1 3 1 is VGA 2 is HDMI 3 is DisplayPort power up Button Push 120BPx lt cr gt default is HDMI I20ASx lt cr gt X 1 on or 0 off Factory Default is enabled AWV Mode I20AWx lt cr gt X 1 on orO off Factory Default is disabled X 1 3 1 lt 197 60m 2 180 60m to 220 67m 3 220 67m to 262 80m Distances longer than 220 require cable grade 6A or USB Length 2OU2. 1x DXW 3 or DXW 3E or DXW 3EU 3EUH accordingly Package Contents 1x Paintable White Wall Plate 1x User Manual PS0053 1 24v DC 15 5 Watt power Supply PS0062 1 24v DC 24 Watt power Supply CA0054 1 8 VGA to 4 RCA Adaptor cable YPbPr and Composite Video Specifications subject to change without notice 21 User Guide APPENDIX 5 Cabling Aurora extender producis have been tested utilizing shielded cabling Although our producis will work fine without shielded cable it is highly recommended for environmental reasons as the signals are high frequency and can radiate as well as be susceptible to external frequencies and possibly cause noise or disruption in the image Unshielded cabling will work fine in a conduits as it will provide the shielding We have found not all cable is created equal even though they appear similar This can affect distance and overall performance Below is a list of cables that have been officially tested with our products by the manufacturer of the cable West Penn Wire CAT 6 Shielded HDBaseT Certified Only in Black 4246F CMR 254246F CMP Plenum CAT 6a Shielded HDBaseT Certified Only in Black 4246AF CMR 254246AF CMP Plenum Both CAT 6 and CAT 6a Shielded Cables utilized a Modular Plug Kit 90170 Bl Includes 100 Connectors 100 Boots Crimp Tool External round Crimp Tool Strip Tool CAT 6 Unshielded Colors 4246 CMR 254246 CMP Plenum Connector 32 6EZP CAT
3. ESTI Arora DXW 3 Series 3 Gang Decora HDBaseT Wall Plate fm inn D D E e KE Wo DXW 3EU DXW 3EUH Manual Number 140703 Firmware v1 21 amp above User Guide SAFETY INSTRUCTIONS Please review the following safety precautions If this is the first time using this model then read this manual before installing or using the product If the product is not functioning properly please contact your local dealer or Aurora for further instructions A The lightning symbol in the triangle is used to alert you to the presence of dangerous voltage inside the product that may be sufficient to constitute a risk of electric shock to anyone opening the case It is also used to indicate improper installation or handling of the product that could damage the electrical system in the product or in other equipment attached to the product bg The exclamation point in the triangle is used to alert you to important operating and maintenance instructions Failure to follow these instructions could result in injury to you or damage to the product AN Be careful with electricity e Power outlet To prevent electric shock be sure the electrical plug used on the product power cord matches the electrical outlet used to supply power to the Aurora product Use only the power adapter and power connection cables designed for this unit e Power cord Be sure the power cord is routed so that it will not be stepped on or
4. with function keys and reconnected the DXW 3 will switch back to the laptop If an RS 232 command is received to switch to the opposite input the unit will do so as well Whenever a source is changed the LED on the button will follow and the RS 232 ports will send a response string to let a remote device know that a change has occurred 10 User Guide EDID Handling The HDMI port will retrieve the EDID from the destination device ex Projector LCD Matrix etc via the HDBaseT connection to the receiver unit The VGA port will use an internal EDID specific to the capabilities of the DXW 3 VGA port with 1080p being the recommended default AWV Audio without Video The DXW 3 Series has the ability to send audio with a video signal being present on the VGA audio connector This is done by sending a 640 x 480 VGA signal when no signal is available so audio can still be heard through the HDMI input on the display or amplifier Keep in mind if this feature is enabled see RS 232 commands installations relying on loss of signal to turn display on and off will not work The DXW 3 factory default is disabled but can be enabled and saved in non volatile memory via RS 232 command Factory Reset Holding both buttons for 5 seconds will restore factory defaults This will be confirmed by both buttons turning cyan Keep in mind all stored settings into the non volatile memory will revert back to the factory defaults of each function accordingly
5. For DVI use a DVI to HDMI cable or DVI to DisplayPort cable If the source is DVI the HDMI or DisplayPort input will try to auto detect If detected the analog audio below the HDMI or DisplayPort connector will become active Holding the HDMI or DisplayPort button for two seconds will force analog audio and will be confirmed with the button LED illuminating cyan To revert back press either button accordingly and the LED will light to its defined prior color YPbPr Input For YPbPr use a VGA to YPbPr cable CA0054 1 When VGA side is selected the DXW 3 will automatically see there is no VGA sync signals and try to lock to YPbPr If present it will then lock and display image Note when using YPbPr auto sense will not work even if enabled Auto sense will only work with VGA and HDMI signals Auto Sense The DXW 3 Series has Auto Sense capability Auto Sense will automatically switch to the last DisplayPort HDMI or VGA input connected provided a hot plug is provided from the source device The DXW 3 factory default is enabled but can be disabled and saved in non volatile memory via RS 232 command In addition the front button selection or RS 232 control will allow the DXW 3 to switch away until another new input is detected For example if a user has a laptop plugged into the VGA port and then connects a Blu ray player to the HDMI the DXW 3 will automatically switch to the HDMI input If after that the laptop is disconnected or signal is removed
6. b lt cr gt Query Cable Disconnect Timer String 20CSp lt cr gt RS 232 commands can be sent to the local RS 232 port or the remote RS 232 port at the receiver User Guide RS 232 Command Usage Example Example String Example Response Set Port 1 Baud Rate to 96008N1 Baud Rate Setup Command 120BR1 9600 8N1 lt cr gt 20BR1 9600 8N1 lt cr gt Set button 1 to Release to green amp Push to blue Button LED Setup 120BL1 G B lt CR gt 20BL1 G B lt CR gt Trigger button 2 HDMI Button Push I20BP2 lt cr gt 20BP2 lt cr gt Turn on Auto Sense Auto Sense Mode 120AS1 lt cr gt 20AS1 lt cr gt Turn off AWV Mode AWV Mode I20OAWO lt cr gt 20AWO lt cr gt Query the firmware revision Query Firmware Revision 20FM lt cr gt 20FM 2 1 lt cr gt Button 2 HDMI is selected in Check button state this example Query Button State 20BP lt cr gt 20BP2 lt cr gt ennen IS Luss O Query Button LED 20BL1 lt cr gt 20BL1 G R lt CR gt Query Auto Sense 20AS lt cr gt 20ASO lt cr gt eee Check AWV Mode State Query AWV Mode 20AW lt cr gt 20AWO lt cr gt 14 CONNECTOR PIN DEFINITION VGA DB15HD Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 HDMI Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Red Pr Green Y S Video C Blue Pb Composite S Video Y Ground Ground Ground TMDS Data2 TMDS Data2 Shield TMDS Data2 TMDS Data1 TMDS Data Shield TMDS Data1 TMDS Data0
7. mud rings have curved or beveled corners that may prevent the DXW 3 from properly fitting Make certain to use a brand that fits the full dimensions listed in the specification section User Guide APPLICATIONS Example 1 Typical DXW 3 Transmitter to RX Receiver St Connect HDMI cable from DXE CAT RX HDMI OUT to Projector or Display HDMI IN HDMI gt DXE CAT RX2 Connect 24v Power P supply or LAN1 PoE HHRHH PH port to PoE switch Wi Switch 24VDC a Power Supply Connect CAT5e or CAT6a CAT5e 330ft 100m CAT6a Step Shielded cable and Shielded 600ft 182m 2 connectors to HDBaseT P RJ45 port on both DXE CAT RX and DXW 3E MacBook Pro oz For Ethernet and or PoE option connect LAN1 or LAN2 of DXE CAT RX to Ethernet PoE Swith or router Then connect PC or other IP device to DXW 3E LAN port DVD player Connect HDMI cable from Source DVD or other to HDMI or VGA input on DXW 3E DXW 3E User Guide Example 2 DXB 8 Button Wall Control to DXW 3 DXB 8 wall controller connected to the DXW 3 series The DXB 8 serial port will connect and draw power from the DXW 3 via the 4 pin RS 232 connection Any serial command can be programmed into the DXB 8 at any baud rate and sent through the DXW 3 to the DXE CAT RX receivers This allows not only the switching of the DXW 3 to be controlled but the remote display device as well Make certain the baud rates are set the same on the DXW 3
8. socket is reversed 1 All transmission distances are measured using Belden 1583A CAT5e 125MHz Solid UTP cable The transmission distance is defined as the distance between the video source and the display 2 To reduce the interference among the unshielded twisted pairs of wires in UTP cable you can use shielded STP cables to improve EMI problems which is worsen in long transmission 1 O User Guide APPENDIX 1 Troubleshooting oe mm a Check that the power plug is properly inserted into a functioning power outlet Keep in mind the DXW 3 can be powered locally or remotely via 1 No Video Signal HDBaseT POE Make certain source is on Verify pin out of connector at each end a Check 24v power supply is plugged in locally or at the far end receiver unit Check to see if Wall supply is plugged into wall outlet Make certain wall outlet has power Make certain RS 232 command for LED state is not set to none for both buttons Verify receiver unit is capable of LAN 3 LAN Not Working H using with DXM G2 Series card cage LAN will not work as it does not have that capability Verify using proper emitter at receiver unit Note the DXW 3 IR receiver l is 38KHz Use Aurora branded accessories for best results Total power between the 2 ports is 5 watts If exceeded the fuse protection will kick in until within specification Try connecting one 5 USB not charging device at a time to make certain it work
9. 1 must be used DXW 3 models will be limited to the capabilities of the receiver accordingly e DXE CAT RX1 Recommended for DXW 3 Model Only e DXE CAT RX2 Recommended for DXW 3 3E or 3EU e DXE CAT RX3 RX8C RX3 A RX3C A Recommended for DXW 3 3E or SEU e DXCI 4 HDBT1 Recommend for DXW 3 Model Only e DXCI 4 HDBT2E Recommended for DXW 3 3E amp 3EU Note Go to www auroramm com for latest manual and firmware User Guide INTRODUCTION About Aurora is pleased to be the world s first HDBaseT wall plate with Display Port HDMI amp VGA YPbPr The DXW 3 Series available in white or black are 3 gang multi input Decora style wall plates Its ability to convert VGA YPbPr S Video Video with audio to HDMI locally and transmit the signal up to 600ft sets this unit apart ffom the competition The sources are remotely selectable via RS 232 commands sent through the matching receiver device DXE CAT RX DXM Matrixes etc In addition there is a LAN port DXW 3E DXW 3EU DXW 3EUH for connection to the network without requiring a separate wall plate The DXW 3EU has two USB ports for powering USB devices and transmitting 480Mbps up to 220ft independently to a different location The DXE 3EUH has 2 USB Ports top for host use PC and lower for charging only and can extend up to 150ft The DXW 3 Series can be remotely powered by the receiver device and also has the ability to transmit IR signals via the sensor window on the front o
10. 15 18 91 o6 911 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 19 17 15 13 16 14 o7 02 03 04 o5 o8 09 010 012 013 014 015 Ground OV SYNC Ground NC SDA Horizontal Sync Horizontal Sync 11 12 10 Type A Receptacle HDMI Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 TMDS Data0 Shield Pin 15 TMDS Data0 Pin 16 TMDS Clock Pin 17 TMDS Clock Shield Pin 18 TMDS Clock Pin 19 CEC Reserved N C on device User Guide Pin15 SCL SCL SDA DDC CEC Ground 5 V Power Hot Plug Detect DisplayPort Pin 1 Lane 0 Pin8 Ground Pin 2 Ground Pin9 Lane 2 Pin 3 Lane 0 PintO Lane 3 Pin 4 Lane 1 Pini1 Ground Pin 5 Ground Pin12 Lane 3 Pin 6 Lane 1 Pin 13 Connected to GND Pin 7 Lane 2 Pin14 Connected to GND CAT5e 6 6A T56BA and T568B Wiring Pin T5684 Pair T568B Pair Wire T568A Color T568B Color ale ti j white green stripe white orange stripe a la o SE D do green solid orange solid ae tip j white orange stripe white green stripe ui M9 blue solid blue solid D 1 tip J white blue stripe white blue stripe e la 3 ane do do orange solid green solid T 4 4 tip J white brown stripe white brown stripe a la 4 ae 4 JE brown solid brown solid Pin 15 Pin 16 Pin 17 Pin 18 Pin 19 Pin 20 User Guide Aux Channel Ground Aux Channel Hot Plug Detect Return for Power 3 3V Pins on plug face
11. 5e Shielded Blue or Gray 4245F CMR 254245F CMP Plenum Connector 32 EZSTP CAT 5e Unshielded 12 Colors 4245 CMR 254245 CMP Plenum Connectors 32 EZP 22 User Guide APPENDIX 6 Warranty Limited 3 Year Warranty Aurora Multimedia Corp Manufacturer warrants that this product is free of defects in both materials and workmanship for a period of 3 years as defined herein for paris and labor from date of purchase This Limited Warranty covers products purchased in the year of 2009 and after Motorized mechanical paris Hard Drives DVD etc mechanical paris buttons doors etc remotes and cables are covered for a period of 1 year Touch screen displays are covered for 1 year touch screen overlay components are covered for 90 days Supplied batteries are not covered by this warranty During the warranty period and upon proof of purchase the product will be repaired or replaced with same or similar model at our option without charge for paris or labor for the specified product lifetime warranty period This warranty shall not apply if any of the following A The product has been damaged by negligence accident lightning water act of God or mishandling or B The product has not been operated in accordance with procedures specified in operating instructions or C The product has been repaired and or altered by other than manufacturer or authorized service center or D The product s original serial number h
12. IR remotes at 38kHz and transmit to other end Receives signals up to 40ft away User Guide Front Right Side e Button The backlit button red green or blue will select the right side source e DisplayPort Connector Use with DisplayPort HDMI or DVI sources like Blu ray players laptops etc e 3 5mm TRS Connector Audio for DVI source to embed audio with the DisplayPort Signal User Guide Rear Panel DXW 3 DXW 3E DXW 3EU DXW 3EUH Rear Connections e 24V DC Power connector for 24V DC power supply If remote device can supply power over HDBaseT then the local power is not required Currently all receiver types from Aurora supply power over the HDBaseT e HDBaseT CAT 5e 6 6A cables can be used For longest distance over 600ft use CAT 6A shielded This connector is right angle for low depth applications e RS 232 Connect RS 232 device up to 115k baud Note there is a 5v line as it is designed to power the DXB 8 8 button wall plate Note The DXW 3EUH model will use 2 position green power connector location as DEV_DET input and ground so only remote power from receiver will work e USB Extender The black 4 pin 3 5mm Euro style connector is a separate extender to work with the DXE USB H1 for SEU model or DXE USB D1P for 3EUH model It will work up to 220 feet for the 3EU and 150ft for the 3EUH with CAT 6 cable allowing the PC to be located elsewhere from the video Note Some 3 gang electrical boxes or
13. Lx lt cr gt higher HDMI IN HDCP Disable v1 21 amp above 120DHx lt cr gt X 0 Normal or 1 HDCP Input disable Button Press Disable v1 21 amp above I20NPx lt cr gt X 0 Normal or 1 Disable Physical Button Press 12 User Guide p serial port 1 or 2 b button number 1 or 3 z URL encoded serial string eg 120PS1 2 Hello World lt cr gt will send Hello World out l the extender serial port on an HDMI button press Button Press Serial Both ports default to 20BP1 0d for button 1 and String 20BP2 0d for button 2 Setting empty string will v1 21 amp above 120PSp b z lt cr gt disable the communication where p serial port 1or2 d is the no cable msg trigger delay in seconds gt O z URL encoded serial string for no cable detected eg 120CS2 10 No cable 0d 0a lt cr gt will send No cable followed by a CR and LF out the local serial port 10 seconds after the cables are removed Cable Disconnect Timer String Both ports default to no message setting empty string v1 21 amp above 120CSp d z lt cr gt will disable the communication Query Firmware Revision 20FM lt cr gt Query Button LED 20BLy lt cr gt y 1 3 1 is VGA 2 is HDMI 3 is DisplayPort Query Auto Sense Mode 20AS lt cr gt Query AWV Mode 20AW lt cr gt Query USB Length 20UL lt cr gt Query HDMI IN HDCP Disable 20DH lt cr gt Query Button Press Disable 20NP lt cr gt Query Button Press Serial String 20PSp
14. and the DXB 8 More information on the DXB 8 can be found on the Aurora website v User Guide Example 3 DXW 3EU Connected to DXE USB H1 The DXE USB H1 Host Unit will be located by the computer using the Mini USB Type B to USB Type A Male cable that is supplied with the DXE USB H1 The 24v DC is not required to be connected when used with the DXW 3EU Power will be drawn from the computer The DXW 3EU will supply 5v to the USB connectors for local charging even if the DXE USB H1 is not connected as it derives its power from the HDBaseT connection Please note many tablet devices have proprietary charging circuits and may not fast charge The RJ 45 of the DXE USB H1 will connect to the DXW 3EU USB 2 0 3 5mm black connector and the RS 232 3 81mm green connector power amp ground only The pin out for the RJ 45 is noted below More information on the DXE USB H1 can be found at www auroramm com DM RJ 45 Male DP Fluy 24V DC Do not connect 57654321 12345678 12345678 Host Detect Do not connect es Device Detect Connect to 5V GND QM RJ 45 Female Dix reme Zurora DXE USB H1 24v DC CAT6 User Guide Example 4 DXW 3EUH Connected to DXE USB D1P The DXE USB D1P Device Unit with 24v DC supply will be located by the product using the USB Type A connectors ex Keyboard mouse etc The DXW 3EUH is the opposite of the SEU model and will not supply 5v to the USB connectors for local charging as it is a Host T
15. armful interference 2 This device must accept any interference received including interference that may cause undesired operation CE A Trademarks All trademarks in this document are the properties of their respective owners User Guide TABLE OF CONTENTS PACKAGE e ei RN KE 1 INTRODUC HON BEEN 2 ele LEE 2 SMIT 2 Front DXW 3 DXW 3E DXW 3EU DXW 3EUH e rerrerrrerrrrrenee 3 Rear Panel DXW 3 DXW 3E DXW 3EU DXW 3EUH l cc ceeeeeeseesessssssesssessssssssesessseeeeeeeeeeeees 5 EEN el ue LE 6 Example 1 Typical DXW 3 Transmitter to RX Heceiver ii eeeserraaaaearerranaanam 6 Example 2 DXB 8 Button Wall Control to DA 7 Example 3 DXW 3EU Connected to DXE USB H1 cceccececeeeeeeeaeeeeeeeeeeeeeeeeaeeeeeeeeeessaaeeeseeeess 8 Example 4 DXW 3EUH Connected to DXE USB DIP errar 9 OPERATION EEN 10 OUI CS SCCO E 10 AUO INGO EE 10 EDID a cinto e WEE 11 AWV A dio without Video E 11 FS EE 11 SERIAL COMMANDS EE 12 RO 22 IAIN eege EENEG 12 RS 232 Command USAGE isisiscsisnniniiiniaiiinicnniniiiniadnind niania ainiin aaia iiia daiidiiaiais ianiai 14 CONNECTOR PIN EFANIHEN es resgeegeegeegeuegeegeeege geseis 15 VOA DBI OHD WEE 15 DA ener eee ee ee Roca ia dan eae ee Goa DA EO di eee 15 ISO OM EE 16 Eed 16 APPENDIX 1 TroubDlIeSNOoting ccccesceeseeeeeeneeeeseeeeseeeneeeesesenseeeseeoeseeeasenenesonseneneeones 17 APPENDIX 2 Firmware Update cccccccsscescceeeeeseneeesenseensonseeeson
16. as been modified or removed or E External equipment other than supplied by manufacturer in determination of manufacturer shall have affected the performance safety or reliability of the product F Part s are no longer available for product In the event that the product needs repair or replacement during the specified warranty period product should be shipped back to Manufacturer at Purchaser s expense Repaired or replaced product shall be returned to Purchaser by standard shipping methods at Manufacturer s discretion Express shipping will be at the expense of the Purchaser If Purchaser resides outside the contiguous US return shipping shall be at Purchaser s expense No other warranty express or implied other than Manufacturer s shall apply Manufacturer does not assume any responsibility for consequential damages expenses or loss of revenue or property inconvenience or interruption in operation experienced by the customer due to a malfunction of the purchased equipment No warranty service performed on any product shall extend the applicable warranty period This warranty does not cover damage to the equipment during shipping and Manufacturer assumes no responsibility for such damage 23 WWW auroramm com Aurora Multimedia Corp 205 Commercial Court Morganville NJ 07751 Phone 732 591 5800 Fax 732 591 6801
17. f the unit for remote control of IR controllable devices Overall the DXW 3 saves money and simplifies an installation by combining the functionality of a switcher converter and extender into one neat package Features 1 DisplayPort Input with Audio 4 1 HDMI Input with Audio for DVI 1 VGA with Audio Converted to HDMI Programmable Buttons for Control of Displays VGA can Accept YPbPr S Video amp Video 1 LAN Connector DXW 3E DXW 3EU DXW 3EUH HDBaseT 600ft 183m Extension 2 USB 2 0 Ports DXW 3EU DXW 3EUH USB Extends Independently 3EU 220ft 3EUH 150ft 1 IR Receiver 40ft Range Auto Sense Buttons RS 232 for Source Select Buttons Backlight Red Green Blue HDCP Compliant Remote or Local Power DXW 3EUH remote only gt 0 0 0 40 HOH OH 4 4 F Fits in Standard 3 Gang Outlet Box 4 Low Depth for Floor amp Table Boxes Warning Do not plug RJ 45 HDBaseT output to non HDBaseT compliant devices or damage may occur to either product User Guide Front DXW 3 DXW 3E DXW 3EU DXW 3EUH DXW 3E DXW 3EU DXW 3EUH Front Left Side e Button The backlit button red green or blue will select the left side source e DB15 VGA Connector VGA up to 1080p can be input Through the use of a breakout cable YPbPr Video and S Video can also be input The DXW 3 will check for VGA signal if no signal YPbPr then Composite Video and finally S Video When switching back and fort
18. h the DXW 3 will remember the last source selected for faster switching All analog sources will be converted to HDMI and sent HDBaseT to the receiver unit Note See appendix for pin out information e 3 5mm TRS Connector Audio for the VGA connector sources to be embedded in HDMI e RJ 45 LAN Connector DXW 3E DXW 3EU amp DXW 3EUH 10 100 LAN via HDBaseT receiver unit Must use DXE CAT RX2 or RX3 for LAN function Note only yellow LED is active and will light solid when link and blink with activity Front Middle e Button The backlit button red green or blue will select the middle source e HDMI Connector Use with HDMI or DVI sources like Blu ray players laptops etc e 3 5mm TRS Connector Audio for DVI source to embed and turn into HDMI e Dual USB Connector DXW 3EU 3EUH USB 2 0 480Mbps and supplies up to 1A of power between both ports Note the power comes from the HDBaseT extender or local supply not the USB extender Great for charging port of USB devices like phones and certain tablets If used for extender it must be used with DXE USB H1 SEU 220ft or DXE USB D1P 3EUH 150ft and is wired separate of the HDBaseT CAT cable Please note iPhone amp iPad devices require use of DXE USB H1 SEU model only connected to PC in order to charge or maintain power iPad DXW 3EUH top port is for PC Host Type A to Type A cable is supplied and lower port is charging only e IR Remote Window Can receive
19. he top USB port of the DXW 3EUH is the Host and the bottom connector is not used The top Host port will connect to the PC USB port via supplied USB Type Ato Type A cable The RJ 45 of the DXE USB D1P will connect to the DXW 3EUH USB 2 0 3 5mm black connector and the RS 232 3 81mm green connector 5v The pin out for the RJ 45 is noted below Note The DXW 3EUH must be paired with the DXE USB D1P for USB proper operation The main difference of the D1 vs D1P is the ability to power locally with 24v DC The D1 does not have this as it is specifically designed to pair with the H1 More information on the DXE USB D1P can be found at www auroramm com DM RJ 45 Male DE Plug GND Must be D1P Model only 67654321 12345678 12345676 Host Detect Connect to 5V E Lo Device Detect Connect to DT Ve RJ 45 Female DXE USB D1 igi Power ES1 USB1 DX Ene Status ES2 USB2 Setup Rurora User Guide OPERATION Source Selection The DXW 3 Series has the ability to change between the VGA port HDMI and DisplayPort via front buttons RS 232 and Auto Sense Once a source is selected the display will lock within a few seconds The time to lock depends on the display but typical time can be from 3 5 seconds Keep in mind the DXW 3 series does not scale so what comes in is what will go back out for both the VGA and the HDMI Most modern displays have scalers and the DXW 3 Series can handle resolutions up to 1080p DVI Input
20. not a proper test The DXW 3 is connected through the HDMI input not VGA of the display The display will handle the signal different as the display will know not to over scan a VGA signal HDMI by definition is treated as a video source first and as a PC source secondary when dealing with video resolutions Warning Do not plug RJ 45 HDBaseT output to non HDBaseT compliant devices or damage may occur to either product 17 APPENDIX 2 User Guide Firmware Update DXW 3 Update Utility DXW 3 Update Software requires a serial cable connected in a null RX to TX TX to RX GND to GND configuration to a PC The firmware can be updated directly at the DXW 3 rear serial port or it can be updated via HDBaseT receiver RS 232 port To force update mode press and hold both front buttons while applying power Then use utility to transfer file which can be found at www auroramm com Pin 3 Transmit Pin 2 Hee TD Receive Data Pin 4 Pin 1 RD Data Terminal Data Carrier Ready DTR Detect DCD not used not used Pin 5 Ground Pin E Data Set dao N Ping a Ringing Indicator RI Pin 7 not used Pin amp Request to Clear to Send Send RATS end RTS tea PC DB 9 RS 232 Serial Port 18 User Guide APPENDIX3 Supported Timing VGA Port Supported Timing 1080p 24 t02ax768 43 1080p 25 1024x768 60 E e e e 19 User Guide APPENDIX 4 Technical Specifications Model Name Vide
21. o Distance HDBaseT DXW 3 DXW 3 Series 328ft 100m 1080p 60Hz 24 amp 36bit CAT 5e 6 6a 7 328ft 100m 1080p 60Hz 48bit CAT 6a 7 328ft 100m 4k2k 30Hz CAT 6a 7 230ft 70m 1080p 60Hz 48bit CAT 5e 6 6a 7 230ft 70m 4k2k 30Hz CAT 5e 6 6a 7 500ft 152m 1080p 60Hz 24bit Long Reach Mode CAT 6 600ft 183m 1080p 60Hz 24bit Long Reach Mode CAT 6A CAT 5e 6 will achieve 328ft 100m for pixel clock lt 225MHz CAT 5e 6 will achieve 230ft 70m for pixel clock gt 225MHz CAT 6a 7 will achieve 328ft 100m for pixel clock gt 225MHz USB 2 0 Distance DXW 3EU 220ft DXW 3EUH 150ft using CAT 6 1080p 60Hz Max Resolution 1920 x 1200 60Hz 4k x 2k 30Hz Mechanical DXWS3Series O O o Plastic front with aluminum rear enclosure Dimensions L x W x D 9 04 x 2 83 4 331 with tabs x 1 404 Note Wall box portion depth 1 04 Weight 0 5lbs Wall mounting Decora 3 Gang Power supply 24V DC DXW 3 amp DXW 3E 6 Watts max DXW 3EU 3EUH 11Watts 5 Watts for USB Ports Important If DXW 3EU is drawing power from the receiver it will require 20 watt or Power consumption better power supply Always check the ratings for transmitter and receiver and add together The result determines required wattage and Aurora power supply needed Operation temperature 0 40 C 32 104 F Storage temperature 20 60 C 4 140 F Relative humidity 20 90 RH no condensation E 20 User Guide
22. pinched by heavy items e Lightning For protection from lightning or when the product is left unattended for a long period disconnect it from the power source N Also follow these precautions e Ventilation Do not block the ventilation slots if applicable on the product or place any heavy object on top of it Blocking the air flow could cause damage Arrange components so that air can flow freely Ensure that there is adequate ventilation if the product is placed in a stand or cabinet Put the product in a properly ventilated area away from direct sunlight or any source of heat e Overheating Avoid stacking the Aurora product on top of a hot component such as a power amplifier e Risk of Fire Do not place unit on top of any easily combustible material such as carpet or fabric e Proper Connections Be sure all cables and equipment are connected to the unit as described in this manual e Object Entry To avoid electric shock never stick anything in the slots on the case or remove the cover e Water Exposure To reduce the risk of fire or electric shock do not expose to rain or moisture e Cleaning Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning e ESD Handle this unit with proper ESD care Failure to do so can result in failure FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause h
23. s before plugging in 2 devices iPad amp iPhone require DXE USB H1 connected to PC in order to charge iPad will maintain power but not charge Make certain DXE USB H1 is connected to PC Make certain DXE USB D1P is powered Make certain the cabling is correct and distance is not exceeded Make certain proper power supply wattage is being used to power both DXW 3 and the receiver Refer to technical specifications for more info on power consumption Check if remote receiver is supplying power Make certain proper power supply wattage is being used to power both DXW 3 and the receiver Refer to technical specifications for more info on power consumption 8 Display will not turn on off when a Turn off AWV feature using RS 232 command as it will put out a 640 no signal is present x 480 signal if no signal is present 9 Certain functions listed in manual a Make certain unit has latest firmware do not function a The DXW 3 does not scale Check the display s settings for over scan mode Displays cannot tell the difference between a video source and a PC source In turn they usually have a setting in the menus to deal with this Check under Aspect Ratio settings PC Video mode etc 10 720p or 1080p is too big for Note if you plug the VGA directly into display and compare to input of 2 LED is not lit on either button 6 USB not working 7 Unit not working screen Over scanned DXW 3 it is
24. seensonseensonseensoessonsoaes 18 DXW 3 Update Unit 18 APPENDIX 3 Supported Timing ccceccceeeeeeeeeneeenseeneeenseensecnseenseonseoassonssonssonssonesoaes 19 VGA Port Supported TIMING EE 19 APPENDIX A Technical Specifications cescecesseeeeseeeeeeeeseeenseeeneeeeeeseaseoesesenseneneeoees 20 APPENDIX 5 Cabling issiria ida a 22 APPENDIX 6 Warranty ccccssccseceseceseeescnseeesenseeesonseessonseessonseoesonseossonseensonsensonssonsoaes 23 User Guide PACKAGE CONTENTS Please make sure the following items are included within your package Contact your dealer if any items are missing or damaged e DXW 3 W White or DXW 3 B Black e 3 Gang Decora Paintable White or Black Wall Plate Accordingly e USB Type A male to Type A Male DXW 3EUH model only Optional Accessories e PS0053 1 24v DC 15 5 Watt power Supply e PS0062 1 24v DC 24 Watt power Supply e CA0054 1 8 VGA to 4 RCA Adaptor cable YPbPr and Composite Video e DXB 8 Button Backlit Wall Controller Panel available in black or white SMC OVO iD e DXE USB H1 USB Host side PC extender unit for DXW 3EU e DXE USB D1IP USB Device side extender unit with 24v DC power supply for DXW 3EUH Compatible HDBaseT Receivers The DXW 3 Series is an HDBaseT technology product and should work with other HDBaseT receivers Please note if product does not supply POE remotely local 24v DC power supply PS0053
Download Pdf Manuals
Related Search