User Manual IDK-1121WR-30FHA1E
Contents
1. gt VTH High VID Backlight Driving Conditions Following characteristics are measured under stable condition at 25 C Table 2 3 Backlight driving conditions Item Symbol Value Unit Condition Min Typ Max Input Voltage Vee 10 8 12 13 2 Volt Input Current lvcc 1 6 A 100 Dimming Power Consumption Piep 19 2 21 Watt 100 Dimming PWM Dimming 200 20K Hz Frequency Swing Voltage 48 5 5 5 Volt 100 Dimming Dimming Duty Cycle 10 100 Analog Dimming Vanalog 1 5 5 Volt Adjustable Dim Voltage ming Range LED Forward IF 80 mA Ta 25 C Note1 Current Operating Life 50000 Hrs Ta 25 C Note 2 3 Note1 Ta means ambient temperature Note2 If modules is driven by high current or at high ambient temperature amp humidity condition The operating life will be reduced Note3 Operating life means brightness goes down to 50 of initial brightness Typi cal operating life time is estimated data 11 IDK 1121W User Manual IDK 1121W User Manual 12 Chapter 3 Signal Characteristics 3 1 Pixel Format Image Following figure shows the relationship between input signal and LCD pixel format 1st Line 1080th Line 2 1919 1920 3 2 Pin Description The module using a pair of LVDS receiver SN75LVDS82 Texas Instruments or compatible LVDS is a differential signal technology for LCD interface and high speed data transfer device Transmitter sh2. Active THD 960 960 960 T clock Section Blanking THB 74 100 1087 Note DE mode 3 4 2 Input Timing Diagram Th 06 KEN e nye PWhs DE Toph RGB Data 5 el al 2 xm X Invalid Data X PS PS A EGB Data Even X Invalid Data 17 IDK 1121W User Manual 3 5 Power ON OFF Sequence VDD power and lamp on off sequence is as follows Interface signals are also shown in the chart Signals from any system shall be Hi Z state or low level when VDD is off VDD vcc Back light dimming or Analog dimming Back light on off Power Sequence Timing Value Parameter Min Typ Max Unit T1 0 5 10 ms T2 30 40 50 ms T3 200 ms T4 0 5 10 ms T5 10 ms T6 10 ms T7 0 ms T8 10 ms T9 10 ms T10 110 ms T11 0 16 50 ms T12 10 ms T13 1000 ms IDK 1121W User Manual 18 Connector amp Pin Assignment 4 1 TFT LCD Module The physical connector interface is described below These connectors are capable of accommodating the following signals and components 4 1 1 Connector Table 4 1 Connector Connector Name Description Interface Connector Interface card Manufacture JAE or compatible Type Part Number JAE FI XB30SRL HF 11 or equivalent Mating
3. Item Specification 1 Frame size 496 50 0 30 X 292 20 0 30 mm 2 View Area 481 50 0 20 X 272 60 0 20 mm 3 Active Area 477 50 0 20 X 268 60 0 20 mm 4 Total Thickness 3 20 0 20 mm 5 Tail length 205 00 6 00 mm Touch controller Advantech 504 Touch Control Board is the ultimate combo board This touch panel controller provides optimum performance of your analog resistive touch panels for 5 wire models It communicates with the PC system directly through USB and RS 232 connectors The design is superior in sensitivity accuracy and friendly operation The touch panel driver emulates mouse left and right button functions Touch Controller Characteristics Specifications Electrical Features 5 Vdc 100 mA typical 50mV peak to peak maximum ripple and noise Bi directional RS 232 serial communication and USB 1 1 full speed Report rate of RS 232 is 180 points sec max And USB is 200 points sec max m Unaffected by environmental EMI W Panelresistance of 5 wire resistive model is from 50 to 200 ohm Pin to pin on same layer 25 IDK 1121W User Manual 5 2 1 2 5 2 2 5 2 2 1 B Touch resistance under ohm Serial Interface 232E Serial RS 232 No parity 8 data bits 1 stop bit 9600 baud 8 1 9600 Supports Windows 2000 Vista XP 7 Windows CE 5 0 6 0 7 0 Windows NT4 Linux DOS QNX USB Interface m Conforms to USB Revision 1 1 full speed If the USB is c
4. Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem OCCUIS 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandise authorization number from your dealer Th
5. IDK 1121WR 30FHA1E TFT LCD 21 5 FHD LED Backlight AD ANTECH Enabling an Intelligent Planet Copyright The documentation and the software included with this product are copyrighted 2013 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements AMI is a trademark of American Megatrends Inc IBM and PC are trademarks of International Business Machines Corporation Intel Core 2 Quad Pentium Dual Core and Celeron are trademarks of Intel Corpo ration WinBond is a trademark of Winbond Corporation All other product names or trademarks are properties of their respective owners Part No 2006112100 Edition 1 Printed in China Nov 2013 IDK 1121W User Manual ii A Message to the Customer Advantech Customer Services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of indus trial environment
6. 0 639 0 689 Red y 0 283 0 333 0 383 Color Chromaticity Green x 0 284 0 334 0 384 Coordinates CIE Green y 0 573 0 623 0 673 4 Blue x 0 105 0 155 0 205 Blue y 0 000 0 048 0 098 Color Coordinates CIE White x 0 263 0 313 0 363 White White y 0 279 0 329 0 379 Central Luminance cd m 240 300 5 Luminance Uniformity 96 75 80 6 Crosstalk in 60Hz 1 5 7 Flicker dB 20 8 Optical Equipment BM 7 DT 101 or equivalent Note 1 Definition of viewing angle Viewing angle is the measurement of contrast ratio at the screen center over a 180 horizontal and 180 vertical range off normal viewing angles The 180 viewing angle range is broken down as below 90 8 horizontal left and right and 90 vertical high up and low down The measurement direction is typically perpendicu lar to the display surface with the screen rotated to its center to develop the desired measurement viewing angle Normal Line 0 0 20 12 O clock direction 0 907 x 90 lt lt 6 O clock OSS d direction 90 Or 90 3 IDK 1121W User Manual Note 2 Contrast Ratio is measured by TOPCON SR 3 Note 3 Definition of Response time measured by Westar TRD 100A The output signals of photo detector are measured when the input signals are changed from Full Black to Full White rising time TrR and from Full White to Full Black fall ing time TfF respectively The respo
7. 30FHATE ee 7 Electrical Characteristics 9 TFT LCD Power Consumption 10 Table 2 1 Power 10 2 1 1 Signal Electrical 11 Table 2 2 Signal electrical characteristics 11 Backlight Driving 2 11 Table 2 3 Backlight driving conditions 11 Signal Characteristics 13 Pixel Format Image ritate tad ont eR e na 14 Pin Description 14 Table 3 1 Pin Description 14 The Input Data 3 16 Interface Timing 17 3 4 1 Timing Characteristics 17 3 4 2 Input Timing 17 Power ON OFF Sequence 18 Connector amp Pin Assignment 19 TET ECD Module dis 20 4 1 1 Connector iiio secet 20 Table 4 1 20 4 1 2 Assignment iere E 20 Table 4 2 Pin 5 20 Backlight Union E Pe Ht o a eb ds 20 4 2 1 Signal for LED light bar 20 rM 21 Touch Screen amp Touch Controller 23 TOU
8. Housing Part Number FI X30HL JAE or compatible 4 1 2 Pin Assignment Table 4 2 Pin Assignment Pin No Signal Name Pin No Signal Name 1 RxOINO 2 RxOINO 3 RxOIN1 4 RxOIN1 5 RxOIN2 6 RxOIN2 7 GND 8 RxOCLKIN 9 RxOCLKIN 10 RxOIN3 11 RxOIN3 12 RxEINO 13 RxEINO 14 GND 15 RxEIN1 16 RxEIN1 17 GND 18 RxEIN2 19 RxEIN2 20 RxECLKIN 21 RxECLKIN 22 RxEIN3 23 RxEIN3 24 GND 25 NC 26 NC 27 NC 28 VDD 29 VDD 30 VDD 4 2 Backlight Unit The physical connector interface is described below These connectors are capable of accommodating the following signals and components 4 2 1 Signal for LED light bar connector Pin No Signal Name Description 1 GND Ground 2 GND Ground 3 GND Ground 4 BL_DIM_P Back light dimming 3 3 V 5 BL_EN Back light enable 5 V 6 NC IDK 1121W User Manual 20 7 V12 Input voltage 12 V 8 V12 Input voltage 12 V 9 V12 Input voltage 12 V 4 2 1 1 LED input connector pin define PIN1 Connector Name Designation LED Connector Manufacturer Sin Sheng or compatible Connector Model Number MS24049HJ Mating Model Number P24049 or compatible LED POWER IN CONNECTOR Figure 4 1 21 IDK 1121W User Manual IDK 1121W User Manual 22 Touch Screen amp Touch Controller 5 1 5 1 1 5 1 2 5 1 3 5 1 4 5 1 5 Touch Screen Touch Characte
9. CH 24 5 1 1 Touch Characteristics aaneen 0 24 5 1 2 Optical Characteristics 24 IDK 1121W User Manual 5 2 Appendix A A 1 IDK 1121W User Manual 5 1 3 Environment 0 0 0422 24 5 1 4 Mechanical 24 5 1 5 Electronic Characteristics 22200000251 24 5 1 6 General 25 Touch controller itio Lo cr era a ta idad 25 5 2 1 Touch Controller Characteristics 25 5 2 2 Pin Assignment and Description 26 Figure 5 1 Board mounted 27 5 2 3 Physical 28 Handling Precautions 29 Optical Characteristics 30 Chapter 1 Overview 1 1 General Description IDK 1121W series is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel a driver circuit and backlight system The screen format is intended to support the FHD 1920 H x 1080 V screen and 16 7M colors RGB 8 bits data All input signals are dual LVDS interface Driver board for the backlight is included 1 2 Display Characteristics Th
10. D Power Consumption Input power specifications are as follows Table 2 1 Power specification Symbol Parameter Min Typ Max Unit Condition VDD Logic LCD Drive 4 5 5 0 5 5 Volt 10 Voltage 0 7 0 8 A VDD 5 0V All white ttern At 60H IDD Input Current Z 0 81 0 89 A VDD 5 0 All white pattern At 75Hz 3 5 4 4 Watt VDD 5 0V All white pattern At 60Hz PDD VDD Power 405 4 9 Watt VDD 5 0V All white pattern At 75Hz Inrush Current 3 A Note 1 VDDrp Allowable Logic 500 mV VDD 5 0V All white LCD Drive Ripple Pattern At 75Hz Voltage Note1 Measurement condition The duration of rising time of power input is 470us VDD LCD Module Input High to Low Control Signal 5 0V 1 0 047 ms VDD rising time 64 Gray pattern IDK 1121W User Manual 10 2 1 1 Signal Electrical Characteristics 2 2 Input signals shall be low or Hi Z state when VDD is off Table 2 2 Signal electrical characteristics Symbol Parameter Min Typ Max Unit Condition VTH Differential Input High Threshold 100 mV VCM 1 2V Note 1 Vn Differential Input Low Threshold 100 mV VCM 1 2V Note 1 Vip Input Differential Voltage 100 600 mV Note 1 Vom Differential Input Common Mode 21 0 12 1 5 VTH VTL Voltage 200MV max Note 1 Note LVDS Signal Waveform Differential Signal
11. all be SN75LVDS83 negative edge sampling or compatible The first LVDS port RxOxxx transmits odd pixels while the second LVDS port RxExxx transmits even pixels Table 3 1 Pin Description Pin No Symbol Description 1 RxOO Negative LVDS differential data input Odd data 2 RxO0 Positive LVDS differential data input Odd data 3 RxO1 Negative LVDS differential data input Odd data 4 RxO1 Positive LVDS differential data input Odd data 5 RxO2 Negative LVDS differential data input Odd data H Sync V Sync DSPTMG 6 RxO2 Positive LVDS differential data input Odd data H Sync V Sync DSPTMG 7 VSS Power Ground 8 RxOC Negative LVDS differential clock input Odd clock 9 RxOC Positive LVDS differential clock input Odd clock 10 RxO3 Negative LVDS differential data input Odd data 11 RxO3 Positive LVDS differential data input Odd data 12 RxE0 Negative LVDS differential data input Even data 13 RxE0 Positive LVDS differential data input Even data 14 VSS Power Ground IDK 1121W User Manual 14 Table 3 1 Pin Description 15 RxE1 Negative LVDS differential data input Even data 16 RxE1 Positive LVDS differential data input Even data 17 VSS Power Ground 18 RxE2 Negative LVDS differential data input Even data 19 RxE2 Positive LVDS differential data input Even data 20 RxEC Negative LVDS differential clock inpu
12. e following are characteristics summary under 25 C condition Table 1 1 Display Characteristics Item Unit Description Screen Diagonal mm 546 86 21 53 Active Area mm 476 64 H x 268 11 V Pixels H x V 1920 x3 x 1080 Pixel Pitch um 248 25 per one triad x 248 25 Pixel Arrangement R G B Vertical Stripe Display Mode VA Mode Normally Black White Luminance Center cd m 300 Typ Contrast Ratio 5000 Typ Optical Response Time msec 16 ms Typ on off Nominal Input Voltage VDD Volt 5 0 V Backlight Input Voltage Volt 12 0 V epe Ms pattern Weight Grams 3100 Typ Physical Size mm 496 5 W x 292 2 H x 20 75 D Electrical Interface Dual channel LVDS Support Color 16 7M colors RGB 8 bits Surface Treatment Anti Glare 3H Temperature Range N series R series Operating C 0 to 60 Storage Shipping C 0 to 60 RoHS Compliance RoHS Compliance TCO Compliance TCO 5 1 Compliance IDK 1121W User Manual 2 1 3 Optical Characteristics Table 1 2 Display Characteristics Item Unit Conditions Min Typ Max Note Horizontal Right CR 150 178 Viewing Angle degree SA 1 Vertical Up CR 10 150 178 Down Contrast ratio Normal Direction 3000 5000 2 Raising Time TrR 10 12 Response Time msec Falling Time TrF 6 7 3 Raising Falling 16 19 Red x 0 589
13. from host to controller USB Interface G V D D G V Tx Rx RS232 Interface Figure 5 1 Board mounted header 5 2 2 3 Touch Screen Connector JP2 Pins and signal descriptions The Touch Screen connector JP2 is a single row by 2 54mm 5 pins 90 degree Male type connector The pins are numbered as shown in the table below JP2 Signal Name Signal Description Pin 1 H UR Drive signal attached to the touchscreen substrate upper right corner when viewed from a user s perspective 2 Y UL Drive signal attached to the substrate upper left corner 3 COM 4 X LR Drive signal attached to the substrate lower right corner 5 L LL Drive signal attached to the substrate lower left corner HAS L URUL LRLL 1 5 1 5 5 1 27 IDK 1121W User Manual 5 2 3 Physical dimension ETM RES04C EEH4EE Touch Control Board Unit mm 75 0x0 5mm 2 2 w AE es 3 8 3 5 un 3 b 5 0 0 1mm Ss Ld 10 3 0 2mm IDK 1121W User Manual 28 Appendix A Handling Precautions A 1 Optical Characteristics The optical characteristics are measured under stable conditions at 25 C Room Temperature 1 2 3 e 10 11 12 Since the front polarizer is easily damaged pay attention not to scratch it Be sure to turn off the power supply when inserting or disconnecting from the input connector Wipe off water drops immediately Long contac
14. is allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer IDK 1121W User Manual iv Contents Chapter Chapter Chapter Chapter Chapter 1 a 1 4 1 5 1 6 2 1 2 2 3 3 1 3 2 3 3 3 4 3 5 4 4 1 4 2 5 1 1 General Description 2 Display 2 222 1 10 2 Table 1 1 Display Characteristics 2 Optical Characteristics tetto etri daten eb ea 3 Table 1 2 Display Characteristics 3 Functional Block Diagram 5 Figure 1 1 Function block diagram 5 Absolute Maximum Ratings essem 6 1 54 TETLCD Module oret tne rri 6 1 5 2 Backlight ioter a 6 1 5 3 Absolute Ratings 2 00 22 6 Outline DIMENSION pe nee 7 1 6 1 IDK 1121WR
15. nse time is interval between the 10 and 90 1 frame at 60Hz or amplitudes TrR 16msec typ To Tir I 1 lt 96 1Frame Note 4 Color chromaticity and coordinates CIE is measured by TOPCON SR 3 Note 5 Central luminance is measured by TOPCON SR 3 Note 6 Luminance uniformity of 9 points is defined as below and measured by TOPCON SR 3 90 50 10 ee 2 9 ss Minimum Luminance in 9 points 1 9 Maximum Luminance in 9 points 1 9 uniformity Note 7 Crosstalk is defined as below and measured by TOPCON SR 3 CT YB YA YA 100 96 Where YA Luminance of measured location without gray level 0 pattern cd m2 YB Luminance of measured location with gray level 0 pattern cd m2 0 0 Yau D 2 W 8 0 0 Yau D 2 W 8 O cam Ya 0 8 W 2 Ya 70 8 2 Ya D 8 W 2 Ya 7D 8 W 2 Y D 2 7W 8 Y D 2 7W 8 IDK 1121W User Manual 4 Note 8 Test Pattern Sub checker Pattern measured by TOPCON SR 3 G Gray Level L127 a Gray Level LO Method Record dB value with TRD 100 Amplitude Time AC Level at 30 Hz Flicker dB 20log DC Level 1 4 Functional Block Diagram The following diagram shows the functional block of the 21 5 inches Color TFT LCD Module 5V LVDS AUO ASIC TFT LCD 1920 3 1080 Figure 1 1 Function block diagram 5 IDK 1121W User Man
16. onnected to the controller the controller will communicate over the USB and will not communicate over the serial port Support Windows 2000 Vista 7 Windows CE 5 0 6 0 7 0 Linux QNX Touch Resolution 2 048 x 2 048 resolution Response Time m Max 20 ms Environmental Feature Reliability B MTBF is 200 000 hours Temperature Ranges B Operating 25 C 85 C B Storage 25 C 85 C Relative Humidity 95 at 60 C RH Non condensing Acquired RoHS certificate Regulatory FCC B CE approvals Dimension 75 mm x 20 mm x 10 mm Pin Assignment and Description Connector and LED Location JP1 Connector USB amp RS 232 Combo Interface JP2 Connector 5 wire Touch screen Interface LED IDK 1121W User Manual 26 5 2 2 2 Combo Interface Connector JP1 Pins and signal descriptions The combo interface connector USB and RS 232 is a box 2 0mm 10 pins 90 degree Male type with lock connector intended to be used with single wired pins in 5 5 pins header The pins are numbered as shown in the table below USB Signal Signal Function RS 232 Signal Signal Function Pin Name Pin 2 Name 1 G Ground 1 G Ground 2 V USB Power 2 V Power 3 G Ground 3 G Ground 4 D USB D 4 TxD Serial Port 5 D USB D 5 RxD Serial Port Signal DB 9 pin RS 232 Sourced by Signal Description Name RxD 2 5 ctlr serial data from controller to host TxD 3 4 host serial data
17. ristics The touch panel is a resistance type used with flat LCD displays Touches via finger or stylus send coordinate points to the PC from voltage changes at the contact point Optical Characteristics Item Specification Remarks 1 TRANSPARENCY 80 3 BYK Gardner 2 HAZE 8 0 3 BYK Gardner Environment Characteristics Remarks Non condensing Item Specification 1 Operation temperature 20 C 70 C 2 Storage temperature 40 C 80 C 3 Operation Humidity 20 80 RH 4 Storage Humidity 20 90 RH Note All terms under 1 atmosphere E Mechanical Characteristics Item Specification Remarks 1 Hardness of surface Pencil hardness 3H JIS K 5600 5 4 750gf 45 degree 2 FPC peeling strength 1 5N 5N Min 1 Peeling upward by 90 2 19 6N 19 6N Min 2 Peeling downward by 90 3 Operation force Pen 0 05N 1 96N Dot Spacer Finger 5 200gf Within guaranteed active area but not on the age and Dot Spacer Electronic Characteristics Item Specification Remarks 1 Rated Voltage DC 7V max 2 Loop X axis 20Q 500Q Figure as bellow FPC connector Resistance Y axis 20Q 500Q Figure as bellow 3 Linearity X lt 1 5 Figure as bellow Reference 250gf Y 1 596 Figure as bellow 4 Chattering lt 15ms Max 5 Insulation gt 20MQ min DC 25V Resistance IDK 1121W User Manual 24 5 1 6 5 2 5 2 1 5 2 1 1 General specification
18. s Whether your new Advantech equipment is destined for the labo ratory or the factory floor you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known Your satisfaction is our primary concern Here is a guide to Advantech s customer services To ensure you get the full benefit of our services please follow the instruc tions below carefully Technical Support We want you to get the maximum performance from your products So if you run into technical difficulties we are here to help For the most frequently asked questions you can easily find answers in your product documentation These answers are nor mally a lot more detailed than the ones we can give over the phone So please consult this manual first If you still cannot find the answer gather all the information or questions that apply to your problem and with the product close at hand call your dealer Our dealers are well trained and ready to give you the support you need to get the most from your Advantech products In fact most problems reported are minor and are able to be easily solved over the phone In addition free technical support is available from Advantech engineers every busi ness day We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products iii IDK 1121W User Manual Product Warranty 2 years
19. t Even clock 21 RxEC Positive LVDS differential clock input Even clock 22 RxE3 Negative LVDS differential data input Even data 23 RxE3 Positive LVDS differential data input Even data 24 VSS Power Ground 25 NC No connection for AUO test only Do not connect 26 NC No connection for AUO test only Do not connect 27 NC No connection for AUO test only Do not connect 28 VDD Power 5V 29 VDD Power 5V 30 VDD Power 5V Note1 Input signals of odd and even clock shall be the same timing Note2 Please follow VESA 15 IDK 1121W User Manual 3 3 The Input Data Format RX O E C COLOR oco TAO RXinO1 lt XX 081 06596 0649 0639 062 0615 RXiO24 LA CD CD CD CD CD RXinO3 C0874 DK ORT DK ORS J wm lt gt lt ED RXinE1 LAM AW gt DK EGS 4 ZE EG X EG2 RXinE2 e AP CY vs C Hs 4 gt gt Cc c ODD 1 Pixel Previous Cycle Current Cycle Note1 Normally DE mode only VS and HS on EVEN channel are not used Note2 Please follow VESA Note3 8 bit in IDK 1121W User Manual 16 3 4 Interface Timing 3 4 4 Timing Characteristics Signal Name Item Symbol Min Typ Max Unit Clock Frequency 1 TClock 40 72 83 MHz Frame Rate Frequency 1 Tv 50 60 75 Hz Period TV 1088 1120 2047 vale Active TVD 1080 1080 1080 T line Section Blanking TVB 8 40 967 Period TH 1034 1060 2047
20. t with water may cause discolor ation or spots When the panel surface is soiled wipe it with absorbent cotton or other soft cloth Since the panel is made of glass it may break or crack if dropped or bumped on hard surface Since CMOS LSI is used in this module take care of static electricity and insure you are earthed when handling Do not open or modify the Module Assembly Do not press the reflector sheet at the back of the module from any direction In case if a Module has to be put back into the packing container slot after it was taken out please press the far end of the LED light bar reflector edge softly oth erwise the TFT Module may be damaged At the insertion or removal of the Signal Interface Connector be sure not to rotate nor tilt the Interface Connector of the TFT Module After installation of the TFT Module into an enclosure no bending twisting forces should be applied to the TFT Module Otherwise the TFT Module may be damaged Small amounts of materials having a no flammability grade are used in the LCD module The LCD module should be supplied by power complying with the requirements of Limited Power Source IEC60950 or UL1950 IDK 1121W User Manual 30 ADWNTECH Enabling an Intelligent Planet www advantech com Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication ma
21. ual 1 5 Absolute Maximum Ratings Absolute maximum ratings of the module is as following 1 5 4 TFT LCD Module Item Symbol Min Max Unit Conditions Logic LCD Drive Voltage VDD 0 5 5 Volt Note 1 2 1 5 2 Backlight Unit Item Symbol Min Max Unit Conditions LED light bar Input Voltage VLED 10 8 13 2 Volt Note 1 2 1 5 3 Absolute Ratings of Environment Item Symbol Min Max Unit Conditions Operating Temperature TOP 0 60 C Operation Humidity HOP 5 90 o RH Note 3 Storage Temperature TST 20 60 C Storage Humidity HST 5 90 RH Note 1 Within Ta 25 C Note 2 Permanent damage to the device may occur if exceeding maximum values Note 3 For quality performance please refer to AUO IIS Incoming Inspection Stan dard Note 4 Operating Temperature 60 C is defined as panel surface temperature IDK 1121W User Manual 6 1 6 Outline Dimension 1 6 1 IDK 1121WR 30FHA1E Front View 256 0 3 205 6 Daly S IJT OF OS sunno s U 0 05 96 ves Tor L 268 60 0 2 T S Active Area 292 20 t0 3 T S Outline 7 IDK 1121W User Manual Rear View 236 03 ujdeq JOS EN XOW IDK 1121W User Manual 292 20 0 5 LCM Outline Sp WO1 50309 S6y Electrical Characteristics 2 1 TFT LC
22. y be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies O Advantech Co Ltd 2013
Download Pdf Manuals
Related Search