Home

User's Manual

1. 7 8 1 PORT A PORT B button The PORT A or PORT B button is used to select the NS unit port which connects to the multi controller or sensor controller 2 Comm Speed 9600 19200 38400 57600 and 115200 buttons Set the communication speed by selecting from the Comm Speed buttons according to the RS 232C setting baud rate of the connected multi controller or sensor controller 3 Data Bit 7 and 8 buttons Set the data bit by selecting from the Data Bit buttons according to the RS 232C setting data length of the connected multi controller or sensor controller o 2 et 4 Stop Bit 1 and 2 buttons Set the stop bit by selecting from the Stop Bit buttons according to the RS 232C setting stop bit of the connected multi controller or sensor controller 5 Parity None Even Odd buttons Set the parity by selecting from the Parity buttons according to the RS 232C setting parity bit of the connected multi controller or sensor controller 6 Write button Pressing the Write button sets the changed contents of port setting communication speed data bit stop bit and parity and restarts the NS unit 7 PT Settings button Pressing the PT Settings button displays a screen to set the contrast adjustment backlight brightness buzzer sound and others 8 Special Screen button Pressing the button displays a screen to change the NS unit to
2. yf Sensing Function m x ten x Setting Settine ve CH TASK LD ON ZERO SNABLE Tey racy 1 Input HIGH Pass Low BANK 1 BRNK1 M Meas Value zc SEMEN H Threshold L Threshold Set Set mm mm The following message is displayed when the communication could not be normally established Time out occurred during the data reception Are you sure you wish to continue You can check the communication setting when selecting No The System Menu Communication Setting screen is displayed when No is o S selected a 5 Communication Setting Screen Seten eru 5 PORT A PORTB m Comm Speed 9600 19200 38400 9800 19200 Data Bit mM 8 Stop Bit l1 NE Parity Mone Even Odd PT Special Settings creen Write button Change the communication setting then reset the NS unit When the System Menu Communication Setting screen is displayed check the communication settings such as the connection port for the sensor controller or multi controller baud rate and data length Communication Setting Screen Operation Method System Menu p 3 23 When the communication returns to normal while the connection stand by screen is displayed the screen will automatically switch to the Main Screen 5 M Never remove the memory card from the NS unit while the NS SmartMonitor is running S Removing the memory
3. Back 639 3eu 480 Undo Execute 447 Operating the Teaching button is available A only when the 2 area measurement setting is SA Sensing V Function Jerem Setting setting SensingSetting enabled Messuremento standard e wi CHECK SensorHead Undo Setting _ Diffuse Regular Mea Object Standard Update Back Sensing Y Function Grah Setting Teaching Line bright 128 192 255 10 Area teaching 0 64 128 192 255 z B E 168 320 490 Back 639 a NS SmartMonitor User s Manual 3 9 Section 3 Setting Sensing Items Sensing Setting Screen 1 CH display and CH switch pull down menu This menu is used to select the channel number of the target controller to display the measured value and status The selection of target CH is available only when connecting to the multi controller 2 Area display and area switch pull down menu This menu is used to select the display area when performing a 2 area measurement The line bright waveform in the specified area is displayed in the line bright display section Operation is available only when the 2 area measurement setting is enabled 3 BANK switch pull down menu This menu is used to select a bank number of the controller to display the measured value and status Switching BANK may take some time 4 Sensing State Disp
4. Note 1 Plug type connector Item ZS XPT2 Applicable controllers ZS Series Ambient temperature Operating 0 to 50 C Storage 15 to 60 C with no icing or condensation Ambient humidity Operating and storage 35 to 8596 with no condensation Dialectic strength 1 000 VAC 50 60 Hz for 1 min Insulation resistance 100 MO by 500 VDC megger Vibration resistance 10 to 150 Hz 0 7 mm double amplitude 80 min each in X Y and Z directions Shock resistance 300 m s 3 times each in six directions up down left right fonward backward Materials Cable sheath PVC Weight Approx 50 g NS SmartMonitor User s Manual 4 3 Section 4 Specifications External Dimensions MEMO gt 0 v m 2 x NS SmartMonitor 4 4 User s Manual B D F G H L BANK name setting 3 22 Communication setting screen 3 2 3 23 3 25 Digit number settings 3 22 Display setting 3 22 Function Setting Screen 3 2 3 15 Graph screen 3 2 3 6 How to switch to the user creation Screen 2 13 Initialize settings 3 19 Label name setting 3 22 Language selection 2 5 2 10 Main Screen 2 6 2 11 3 2 3 3 Measurement settings 3 17 Memory Card 1 7 2 5 2 9 Monitor 1 9 NS SmartMonitor Automatic start up procedure 2 4 Connection Connection and wiring How to start up 2 2 Operating Environment Operation procedure Restrictions Selection start up procedure 2 8 Startup and En
5. Special Function Special Function Device Monitor 5 Switching LI Device Honi tor Com Test Com Test Select 0 START SRT The NS unit is once reset and the NS SmartMonitor is started up Check the configuration in the memory card and retry to operate from step 4 described above when NS SmartMonitor is not displayed in the Special Function menu The following start up screen is displayed when the NS SmartMonitor is started up Select the language to be displayed on the NS SmartMonitor screens After selecting the language when the ZS series controller has been started up press the OK button according to the instructions displayed on the screen After the ZS series controller has been started up press the 0K utton XThe controller startup has been completed when a measurement value is displaved at the main digital section OK 1 Languge When the NS SmartMonitor starts up characters are displayed on the screen in the previously selected language When the NS SmartMonitor starts up for the first time the start up screen is displayed in English Selecting the Japanese button switches the screen display to Japanese NS SmartMonitor User s Manual Section 2 How to start up the NS SmartMonitor 9 The NS SmartMonitor program is executed and the Main Screen below is displayed
6. c y Sensing Function Mein X Creph Setting Setting Mee lt lt Measure BANK BANK1 Er ll TASKI gt gt Setting for TASK2 M Setting for TASK3 10 gt gt Undo Update NS SmartMonitor 3 1 8 User s Manual Section 3 Setting Controller Conditions Function Setting Screen Bi Initialize settings The Initialize settings screen is used to initialize entire settings for the controller of the Target CH Pressing the Initialize all button displays a dialog for the confirmation of setting initialization processing as below wem BANK BANK 1 Initialize settings System settings Measure gt gt Initializes all settings on controller Save Settings Initialize all CH BANK Selection Display Settings gt gt NS SmartMonitor User s Manual 3 19 75 o 2 et gt o Section 3 Setting Controller Conditions Function Setting Screen Save Settings Pressing the Save Settings button saves the entire settings of the Target CH in the controller The contents upon saving are retained even when turning OFF the power of the target controller after saving the settings Pressing the Read file or Save file button enables the reading of the setting values from the file saved in the memory card or the saving of the setting value data to the memory card The setting data is saved in the file
7. 4447 With respect to the sensor controller the settings below perform the 2 area measurement A Setting when Glass material FILM OTHERS 2 Setting when Glass thickness measurement mode Move CHECK TASK result varies as below depending on the 2 area measurement and others When 2 area measurement is When measurement other than 2 performed area measurement is performed TASK1 Surface distance Measurement result 71 TASK2 Rear surface distance Unused 2 TASK3 Thickness distance Unused 2 1 The result is a thickness distance value when the thickness measurement is set Other than the above the result is a surface distance value 2 An error always occurs NS SmartMonitor User s Manual 3 3 Section 3 Monitoring Measured Value Main Screen 3 BANK switch pull down menu This menu is used to select a bank number of the controller to display the measured value and status Switching BANK may take some time 4 Indicators Indicators display the current statuses of LD ON ZERO ENABLE HIGH PASS and LOW 5 Measured value display Displays the current measured value The display functions the same as the main digital function of the controller UE Error is displayed when an error occurs in the measurement ABEL Any characters 5 in 2 byte character and 10 in 1 byte character can be displayed on the display Characters to be displayed are set on the
8. Function Setting Label setting Screen UA Display setting p 3 22 6 Threshold value display Displays the present L Threshold and H Threshold values Pressing the Setting button switches to the following screen to enable the threshold value setting o 2 et gt o Enter the value The range is between 999 999999 to 999 999999 H Threshold 225 34 Pressing a column displays the Verr 175 BARRA input pad for the value setting Setting is available in the range of Threshold Hysteresis gt L Threshold 7 Sub display Displays Incident Level Current Voltage Resolution LD power and Present Value with the switch function To switch the display press the gt gt button Displayed items differ according to the target CH controller Incident Level Displayed only when the target CH is a sensor controller Current Displayed only when the target CH controller is set to Current Voltage Displayed only when the target CH controller is set to Voltage Resolution Always displayed LD power Displayed only when the target CH is a sensor controller NS SmartMonitor 3 4 User s Manual 8 Section 3 Monitoring Measured Value Main Screen Present Value Always displayed Label is also displayed when the Resolution and Present Value are displayed ww ERROR is displayed when an error occurs in the measurement for the respective
9. INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM PERFORMANCE DATA Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty It may represent the result of OMRON s test conditions and the users must correlate it to actual application requirements Actual performance is subject to the OMRON Warranty and Limitations of Liability CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons It is our practice to change model numbers when published ratings or features are changed or when significant construction changes are made However some specifications of the product may be changed without any notice When in doubt special model numbers may be assigned to fix or establish key specifications for your application on your request Please consult with your OMRON representative at any time to confirm actual specifications of purchased products NS SmartMonitor User s Manual 5 EJ 5 E Introduction DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes even when tolerances are shown ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate however no responsibility is assu
10. Screen When the Target CH is a sensor controller Displays the status of respective item of function settings Changing the setting values and pressing the Update button enables the transmission of the contents of the change to the target controller The processing items which were changed from the setting contents in the controller of the Target CH are displayed in the red color Pressing the button returns to the Function Setting System Settings screen TA Sensing Function aes fs y Sensing Function Main y Graph Setting Setting Ver Main Graph JI Setting Setting Ver BANK BANK lt lt Measure BANK 1 1 lt lt TASKI BANK1 1 Scaling gt 554 ScslingMode OFF Scaling setting Average 10 gt gt Smooth Differential Mode OFF Hold Average AverageCount 128 Y Zero reset judgment Undo Update Undo Update Select the processing item to be displayed 52 Sensing 7 Function Main Graph X Setting Setting Y ver Ver Ry BANK BANK 1 5 Non Measurement Non Messuring Nons Kaw eios Measurement Ck Level LinearOutput cid 55 Judgement Settine 2 ParallellN Hysteresis B paa TimerMode OFF Select 1 0 Undo Update Select the processing item to be displayed E 4 Settings TASK2 TASK3 are available when 2 area measurement is set for the sensing setting
11. System Menu 3 23 Section 4 APPENDIX 4 1 Error Messages and Countermeasures 4 2 Specifications and External Dimensions 4 3 RS 232C Cable for Connecting to a programmable controller or programmable terminal 4 3 Index 4 5 NS SmartMonitor User s Manual Oo 5 a 5 4 Oo 3 5 2 10 Revision History NS SmartMonitor User s Manual 4 6 Section 1 FEATURES o 2 5 E 44 Features of NS SmartMonitor 1 2 System Configuration 1 3 Restrictions of NS SmartMonitor 1 6 Operating Environment for NS SmartMonitor 1 7 Operation procedure 1 8 NS SmartMonitor User s Manual 1 1 saqunivad 1 2 Section 1 Features of NS SmartMonitor Features of NS SmartMonit The NS Smart Monitor is the software which is designed to display measured values from the ZS series Smart Sensor to display these values in graphs and to read save the setting data on the programmable terminal NS Direct connection between the programmable terminal NS and multi controller ZS MDC or sensor controller ZS LDC via the RS 232C enables setting the Smart Sensor displaying the measured values displaying graphs and other features Displaying measured value Mais ft 7 Sensing Function el DEN Settinr Setting J RU OH TASK LD ON ZERO NABLE umm HIGH PASS LOW Qv TASKT Sten BANK 1 Meas Value xo
12. be started up from the user creation screen NS SmartMonitor User s Manual 3 25 o 2 et gt o 3 26 System Settings Screen Settings Menu Exit PT Settings Menu Exit qe 3 Page T oe Page Kev Press Sound change MS change 2 1 SENE mes 4 Buzzer Sound Calender Check ON OFF ERR ON 2 Wed April 13 2025 5 Backlight 2 High Middle Low 3 4 49 42 PM E S E 6 1 Key Press Sound Select ON OFF buttons Setting to turn ON or OFF the key press sound upon pressing the touch switch which accepts the input to the NS unit is available ON Sounds the input sound upon pressing the touch switch which accepts the input to the unit OFF Does not sound the input sound upon pressing the touch switch which accepts the input to the unit Default setting is ON 2 Sound ON OFF and ERR ON buttons Setting whether or not to sound the buzzer such when an error occurs in the communication with the controller is available ON Sounds buzzer upon instruction from the host or when an error occurs OFF Does not sound buzzer ERR ON Sounds buzzer only when an error occurs Default setting is ERR ON 3 Backlight brightness High Middle and Low buttons Sets the backlight brightness of NS unit Brightness can be set with three levels Default setting is High 4
13. the Log folder on the memory card The name of the saved file is shown below GRAPH csv is automatically replaced with serial numbers whose range is between 000 to 999 NS SmartMonitor User s Manual Section 3 Setting Sensing Items Sensing Setting Screen Setting Sensing Items Sensing The figure below shows the sensing setting screen For details on its functions refer to the User s Manual of your controller Only data from the connected sensor controller can be applicable 5 YY Sensing Function 2 Main Graph y Setting Setting J Ver CH Des 1 Line bright 64 128 192 255 lr 0 64 128 192 EAD 9 v Present vae 160 5 188 141 Sensing Function 4 INCLEV LD PWK tuin X Bran X Setting X Setting SUR 1007 22 1 Specify displayrange Line brisht 64 128 192 255 6 se stp 480 bows 920 TET PF SensingSetting 639 7 FT ET 168 Ed 8 3 4x 8x V f re em Back 839 Line bright 64 128 192 Specify display range 64 128 192 255 m Spfy Mea Re Main J Graph Ji EEUU X SensingSettine panampi Line bricht G4 ies 192 255 2 64 128 192 255 Teaching Start position 2 5 End position 639 169 8 10
14. the monitoring of the sensing state and line bright data 7 Specify display range screen Sets the display range of the line bright display Specify display range Cena 9041 Pressing a column displays the input location pad for the value setting H cl 0 10 NH 4x 8x Center location setting Sets the vertical axis display center location of the line bright display section 1 button Increments the vertical axis display center location of the line bright display section by one 75 o 2 et This button is valid when display magnification is two four or eight 10 button Increments the vertical axis display center location of the line bright display section by ten This button is valid when display magnification is two four or eight 1 button Decrements the vertical axis display center location of the line bright display section by one This button is valid when display magnification is two four or eight 10 button Decrements the vertical axis display center location of the line bright display section by ten This button is valid when display magnification is two four or eight Same Size button Displays the vertical axis of the line bright display section in the same magnification in the range between 0 to 639 NS SmartMonitor User s Manual 3 1 1 75 o t 2 et 3 12 Setting Sens
15. while the NS SmartMonitor is running will cause malfunctions of EE the NS SmartMonitor If the memory card is removed from the NS unit during the NS SmartMonitor is running insert the memory card then reset the NS unit If the message described below is displayed upon start up and the system does not start up normally the version number of the NS unit system may be older than 6 02 In the NS SmartMonitor CD ROM the NS unit system with the version number 6 20 is contained In addition update the NS unit system version to 6 20 according to the NS SmartMonitor User s Manual 2 1 1 o et c o 3 m 3 2 12 Section 2 How to start the NS SmartMonitor procedure for updating the NS unit system to V6 20 pdf which is contained in the CD ROM Failed to read host registration Correct host registration with NS Designer Then press OK and download project data Or Could not read project Data log Press OK button and download project data NS SmartMonitor User s Manual Section 2 How to switch from the NS SmartMonitor to the user creation screen How to switch from the NS SmartMonitor to the user creation screen The procedure for switching to the user creation screen from the NS SmartMonitor upon the NS SmartMonitor selection start up is described below 1 Press two corners simultaneously out of four on the touch panel screen of the NS unit to display the System Menu scre
16. 3 8568 OMRON ASIA PACIFIC PTE LTD 83 Clemenceau Avenue 3111 01 UE Square 239920 Singapore Tel 65 6835 3011 65 6835 2711 OMRON CHINA CO LTD BEIJING OFFICE Room 1028 Office Building Beijing Capital Times Square No 88 West Chang an Road Beijing 100031 China Tel 86 10 8391 3005 Fax 86 10 8391 3688 Authorized Distributor Cat No Z227 E1 01 C OMRON Corporation 2005 Rights Reserved Note Specifications subject to change without notice Printed in Japan 0605 0 2M M
17. 999999 gt H Threshold 225 Pressing a column displays the 3 L Threshold 175 BARRA input pad for the value setting OK Cancel Setting is available in the range of H Threshold Hysteresis gt L Threshold 9 Scale button Switches to the following screen to set the vertical axis numeric value axis and horizontal axis time axis Pull down menu is used to display the selection Vertical Scale Amn div Y list Center Point 200 Pressing a column displays the input pad for the value setting The input range 1000 101606 Minimum span 50 Horizontal Scale Is div Pull down menu is used to display the selection list Back NS SmartMonitor User s Manual 3 7 75 o t 2 et 3 8 Section 3 Displaying Measured value on the Graph Form Graph screen Vertical Scale Sets the scale on the vertical axis in the graph plot section Center Point Sets the center value on the vertical axis in the graph plot section Values within the input range can be set Setting values are rounded at the value of minimum input range Horizontal Scale Sets the scale on the horizontal axis in the graph plot section 10 Auto button Sets the vertical axis on the scale in the graph plot section where H Threshold and L Threshold can be displayed 11 Waveform button Saves the displayed waveform on the graph as a csv file Data is saved in
18. C 2 Double click the NS5SmartMonEXT exe file which was copied to the PC The following directories and files are created NS5SmartMonEXT ExtBootsmart BIN o ETCSYS E FGW 2 FONT P OTHER 5 SYS RUN m sys datalog cfg DefBaseL DC ini DefBaseL DCR ini DefBaseMDC ini DefBaseMDCR ini omron hst print cfg SmartMon IPP STARTUP BAT BankName txt Label txt mm txt time txt unit txt unitcom txt unitcom1 txt PNLPGOOO IPW PNLPGO001 IPW PNLPGO002 IPW PNLPGO003 IPW PNLPGO004 IPW PNLPGO005 IPW PNLPGOO6 IPW PNLPGO007 IPW PNLPGOOA IPW PNLPGOOB IPW PNLPGOOF IPW PNLPGO010 IPW PNLPGFFE IPW PNLPGFFF IPW NS SmartMonitor 2 8 User s Manual Section 2 How to start up the NS SmartMonitor 3 Copy the folders and files in the NS5SmartMonEXT directory to the root directory of the memory card NS5SmartMonEXT ETC E ETC ExtBootsmart ExtBootsmart PNLPG003 IPW PNLPG003 IPW PNLPG004 IPW PNLPG004 IPW PNLPG005 IPW PNLPG005 IPW When drive E is assigned as a memory card 4 Turn OFF the power of the NS unit and insert the memory card described TA Check the system security before performing the operations such as turning ON OFF the power and pressing the reset switch Do not turn OFF the power of the NS unit or remove the memory card while accessing the memory card above to the memory card connector on the side of the NS unit a 5 Before
19. Contrast lt lt lt gt gt gt buttons Adjusts the contrast of the screen Contrast can be adjusted with 100 levels lt lt Lowers the contrast by 10 levels lt Lowers the contrast by 1 level gt Raises the contrast by 1 level gt gt Raises the contrast by 10 levels NS SmartMonitor User s Manual Section 3 System Menu 5 Date setting Sets and displays date of the system clock in the NS unit Date and time are not correctly set at shipment Time stamp and others are not correctly written to the saved file when date and time are not correctly set How to set is described below Calender Check Wed April 13 2005 The current date is displayed on the button Press the button when setting date 4 49 42 PM The current time is displayed on the button Press the button when setting time Pressing the date setting button and time setting button displays the input dialog Date setting yyyy mm dd Fa Rr e ajsje un sje an jejej 1jzjsjows ENER ENER Follow the input format below to set date yyyy mm dd yyyy Western year mm month dd day Enter a western year by four digits Example To enter January 1st 2001 Enter 2001 1 1 It is not necessary to fill a space by zero 75 o 2 et Follow the input format below to set time hh mm ss hh
20. EHE H Threshold L Threshold Sensing setting in Y Sensing y Function anmh setine H e Ares BANK 1 BANK1 vi Sensing state Present Value mm 188 141 INDLEV LD PWS 1007 22 1 EE SensineSettine NS SmartMonitor User s Manual Line bright 64 128 192 255 64 128 192 255 160 3204 480 639 Displaying measured value in graphs TT ee Set Seve Start s Thresh Scale Auto Wave 240 228 iq 200 O EA NEZEHNSURD EER HEE 160 lt lt lt gt gt gt Timing 2s 12s 22s 32s 42s Function setting Main Ji Graph X EE X ver BANK BANK T 1 posee ef ss System settings Measure gt gt Key lock Lock Decimal place 346 Y Save Settings EcoMode Normal Sensor cms MEZ Selectic bikie Language Japanese English Display Settings gt gt Undo Update Section 1 System Configuration tem Configuration The figure below shows the system configuration 4 NS SmartMonitor and the SmartMonitor 25 for the cannot be used simultaneously Q Do not connect the SmartMonitor ZS for the PC to the USB of a multi controller or sensor controller EE while using the NS SmartMonitor Simultaneous connections of NS SmartMonitor and SmartMonitor ZS for the PC will cause a communication
21. ER Sensing Function os ecu Cree Mec LD ON ZERO SNABLE U External wm O input BANK 1 Meas Value j LABEL mm H Threshold get LThreshold ETT mm mm The following message is displayed when the communication could not be HIGH PASS LOW normally established Time out occurred during the data reception Are you sure you wish to continue You can check the communication setting when selecting No The System Menu Communication Setting screen is displayed when No is selected Communication Setting Screen sss EE NN PORT A Comm Speed 9000 19200 38400 90M 19200 Data Bit 7 5 Stop Bit L1 IE Parity Mone Even Odd PT Special Settings Screen Write Write button o et t m c E 5 m 5 Change the communication setting then reset When the System Menu Communication Setting screen is displayed check the communication settings such as the connection port for the sensor controller or multi controller baud rate and data length UA Communication Setting Screen Operation Method System Menu p 3 23 When the communication returns to normal while the connection stand by screen is displayed the screen will automatically switch to the Main Screen 5 Never remove the memory card from the NS unit while the NS SmartMonitor is running A Removing the memory card
22. Monitor 2 2 User s Manual Section 2 How to start up the NS SmartMonitor How to start up the NS SmartMonitor Files below are saved on the CD ROM for NS SmartMonitor Select the necessary file s according to the type of the NS unit to be used NS5SmartMonAUTO exe For the NS5 series NS SmartMonitor Automatic Start up NS5SmartMonEXT exe For the NS5 series NS SmartMonitor Selection Start up NS8SmartMonAUTO exe For the NS8 NS10 series NS SmartMonitor Automatic Start up NS8SmartMonEXT exe For the NS8 NS10 series NS SmartMonitor Selection Start up aul The NS8SmartMonAUTO exe and NS8SmartMonEXT exe files are used when using the NS12 series CHECK However the display size of the NS SmartMonitor is displayed in the VGA size z Sensing Funct ion Main Graph Setting Setting J ver cH TASK a wm HIGH PASS LOW BANK gt 11 BANK1 tes Vale 4 N312 Screen display LABEL mm size H Threshold T L Threshold o et t m c E 5 m 5 set mm ave Note that the system program to be stored in the memory card is different for the NS SmartMonitor x Automatic Start up Procedure or NS SmartMonitor Selection Start up Procedure CHECK NS SmartMonitor User s Manual 2 3 Section 2 How to start up the NS SmartMonitor NS SmartMonitor Automatic Start up Procedure This section describes the NS SmartMon
23. S SmartMonitor Whether or not an error occurs in the NS unit port which connects to the multi controller or sensor controller Whether or not the communication settings are consistent with the controller which connects to the NS unit Whether or not the cabling is wrong Simultaneously press two corners out of four How to display the System Menu Screen is shown below B ain M Graph yf Sensing Function Mese Setting J Setting 9 CH TASK LD ON ZERO NABLE v TASKI v pus HIGH Pass Low BANK z 1 BANK1 hd Mess Value Simultaneously press two gt 9 LABEL mm corners out of four a H Threshold L Threshold Set 175 000000 O Note that the corner on the touch panel screen where nothing is displayed should be Set pressed first Pressing a corner where any button is displayed executes the function of the button Then any corner other than the first corner can be pressed The System Menu screen can be displayed even if a button is displayed on the corner NS SmartMonitor 3 24 User s Manual Section 3 System Menu System Menu Screen System Menu PORT A o Comm Speed 9600 19200 38400 2 96m 19200 Data Bit ENDE 3 Stop Bit 1 2 Parity None Even Odd 5 PT Special Settings Wite 6
24. TION EXPRESS OR IMPLIED REGARDING NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE OMRON DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS WHETHER SUCH CLAIM IS BASED ON CONTRACT WARRANTY NEGLIGENCE OR STRICT LIABILITY In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY REPAIR OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED STORED INSTALLED AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION ABUSE MISUSE OR INAPPROPRIATE MODIFICATION OR REPAIR NS SmartMonitor User s Manual Introduction SUITABILITY FOR USE THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES Please refer to separate catalogs for OMRON s safety rated products OMRON shall not be responsible for conformity with any standards codes or reg
25. TO exe For the NS8 NS10 series NS SmartMonitor Automatic Start up NS8SmartMonEXT exe For the NS8 NS10 series NS SmartMonitor Selection Start up ST The NS8SmartMonAUTO exe and NS8SmartMonEXT exe files are used when using the 512 series check However the display size of the NS SmartMonitor is displayed the VGA size z uonoes S 4 4 C 512 Screen display m size mE 4 pue dnbelS Note that the system program to be stored the memory card is different for the NS SmartMonitor Automatic Start up Procedure or NS SmartMonitor Selection Start up Procedure NS SmartMonitor Automatic Start up Procedure lt This section describes the NS SmartMonitor automatic start up procedure using the lt example of the NS5 series 1 Copy the NS5SmartMonAUTO exe file on the NS SmartMonitor CD ROM to the hard disk in the PC NS SmartMonitor User s Manual 2 3 Helpful information regarding operation and reference pages are introduced here using symbols ita 9 CHECK Title of each section Index label Indicates the section number and title Cross header Overview of the cross header This page has been made purely for explanatory purposes and does not exist NS SmartMonitor User s Manual Introduction Editors Note iIMeaning of Symbols Windows dialog boxes and other GUI elements displayed on the NS SmartMonitor are in
26. ata Bit S adjustment on the NS unit screen Stop Bit 1 HH backlight brightness buzzer sound Parity None Even Odd and others PT Special Settings reen Write UA p 3 23 NS SmartMonitor 3 2 User s Manual Section 3 Monitoring Measured Value Main Screen Monitoring Measured Value Main Screen The current statuses of controllers such as measured value and various types of input and output can be displayed 2 X Graph X E oer ver Ver LD ON ZERO sues Ex 4 PO TASK v nme 9 HIGH Pass Low BANK 1 BANK1 po 3 Meas Value oiu MAI H Threshold Set 1s L Threshold Set 6 1 7 C 1 CH display and CH switch pull down menu This menu is used to select the channel number of the target controller to display the measured value and status The selection of target CH is available only when connecting to the multi controller 2 TASK display and TASK switch pull down menu This menu is used to select the task number of the controller to display the measured value and status The target CH numbers differ between the multi controller and sensor controller 75 o 2 et When the target CH is a multi controller The task can be selected from the range between TASK1 to TASK4 When the target CH is a sensor controller The task can be selected from the range between TASK1 to TASK3
27. ayed on the second page Detailed setting items for the 2 area measurement setting are displayed on the third and fourth pages Operations on the third and fourth pages are available only when the 2 area measurement is valid Pressing the Undo button returns the respective sensing setting item to the previous state before the change Pressing the Update button transmits the contents of the change for sensing setting and updates the setting values x 4 Note that the contents of the change are deleted when turning OFF the sensor controller Q even if the Update button is pressed and the sensor controller parameters are changed CHECK UA Save Settings p 3 20 10 Area teaching button The Area teaching button is used by pressing when automatically specifying or readjusting Area 2 for performing 2 area measurement Controller finds an optimum area within the adjacent range of the currently specified range o 2 et gt o Perform the manual area setting when specifying any area NS SmartMonitor 3 1 4 User s Manual Section 3 Setting Controller Conditions Function Setting Screen Setting Controller Conditions Function Setting Screen The Function Setting screen is used to display a list of setting values which are registered in the controller of the target CH In addition updating the setting values and transmitting them to the target controller are available For details on s
28. ber of the controller to display the measured value in a graph form Switching BANK may take some time Start Stop button This button is used to start stop the graph display Displaying Measured Value in a Graph Form Displays Measured Values by plotting them on the graph Measured Value H Threshold and L Threshold are plotted in the black line red NS SmartMonitor User s Manual Section 3 Displaying Measured value on the Graph Form Graph screen dotted line and blue dotted line respectively to be displayed The graph retains the measured values equivalent for 3 minutes and 20 seconds 6 Timing signal Displays ON OFF status of timing signal in Timing Chart 7 Graph Display Scroll buttons lt lt lt gt and gt gt These buttons are used to scroll the time axis on the graph display lt lt FBack for one page of the graph display lt FBack for one scale of the graph display Back for two scales when the horizontal axis scale is set to 500ms div gt FForward for one scale of the graph display Forward for two scales when the horizontal axis scale is set to 500ms div gt gt FForward for one page of the graph display Operation is disabled when obtaining the measurement data 8 Threshold button o Switches to the following screen and enables the threshold value setting 5 Enter the value The range is between 999 999999 to 999
29. card while the NS SmartMonitor is running will cause malfunctions of CHECK the NS SmartMonitor If the memory card is removed from the NS unit during the NS SmartMonitor is running insert the memory card then reset the NS unit If the message described below is displayed upon start up and the system does not start up normally the version number of the NS unit system may be older than 6 02 In the NS SmartMonitor CD ROM the NS unit system with the version number 6 20 is contained In addition update the NS unit system version to 6 20 according to the NS SmartMonitor 2 6 User s Manual Section 2 How to start up the NS SmartMonitor procedure for updating the NS unit system to V6 20 pdf which is contained the CD ROM Failed to read host registration Correct host registration with NS Designer Then press OK and download project data Or Could not read project Data log Press OK button and download project data o et c o 3 m 3 NS SmartMonitor User s Manual 2 7 Section 2 How to start up the NS SmartMonitor NS SmartMonitor Selection Start up Procedure This section describes the procedures for the start up by switching from the user creation screen to the NS SmartMonitor in the NS unit when the user creation screen is displayed by using the example of the NS5 series 1 Copy the NS5SmartMonEXT exe file on the NS SmartMonitor CD ROM to the hard disk in the P
30. ck Had Decimal place 3dig Save Settings EcoMode Normal Sensor Save Infomation n Selecti Language Japanese English Display Settings gt gt Undo Update Measurement settings The Measurement Settings screen is used to display a list of setting values related to the controller of the Target CH 75 o 2 et 3 17 When the Target CH is a multi controller The Measurement Settings screen displays the input CH assignment calculation settings from TASK1 through TASKA and assignment status Changing the setting values and pressing the Update button enables the transmission of the contents of the change to the target controller The processing items which were changed from the setting contents in the controller of the Target CH are displayed in the red color Pressing the button returns to the Function Setting System Settings screen Sensing Function Mein X X Setting X Setting ver Ver lt lt Measure gans BANK 1 i lt gt 1 2_______ Switches the respective processing item of Select input CH lo the selected processing category and the TASKI ipata display page when parameters are z displayed over more than one page TASK2 InputB None TASK3 InputG None TASK4 Select 1 0 TG Update NS SmartMonitor User s Manual Section 3 Setting Controller Conditions Function Setting
31. d When the End button pressed the mode is changed to the area monitoring mode and the area bar automatically moves according to the value obtained from the controller The button display changes to Set Start Position button Pressing the button selects the start position and press NS SmartMonitor User s Manual the 1 10 1 or 10 button to increment decrement the setting value of the start position by 1 10 1 or 10 The operation above is available only in the area setting mode Section 3 Setting Sensing Items Sensing Setting Screen Start End position setting The area start end position can be set directly The operation above is available only in the area setting mode End Position button Pressing the button selects the end position and press 1 button 10 button 1 button 10 button the 1 10 1 or 10 button to increment decrement the setting value of the end position by 1 10 1 or 10 The operation above is available only in the area setting mode Increments the value of the selected position of the Start position or End position by one The operation above is available only in the area setting mode Increments the value of the selected position of the Start position or End position by ten The operation above is available only in the area setting mode Decrements the value of the selected position of the Sta
32. d 2 2 N W R S T V Operating controller 1 10 PT Settings screen 3 23 3 26 RS 232C Cable 4 3 Save Settings 3 20 Screen Layout 3 2 Select bank 3 21 Select CH 3 21 Sensing Setting Screen 3 2 3 9 Special Screen 2 10 2 13 3 23 3 28 System Menu screen Communication setting Screen 3 2 3 23 3 25 Display method 2 9 3 24 PT Settings screen 3 23 3 26 Special Screen 2 13 3 23 3 28 System Settings 3 17 Types of start up files 2 3 Version Information Display Screen 3 2 NS SmartMonitor User s Manual 4 5 Section 4 Revision History Revision History A manual revision code appears as a suffix to the catalog number at the bottom of the front and back covers of this manual Cat No Z227 E1 01 Revision code Revision code Date Revised contents 01 June 2005 Original production Ver 1 01 gt 0 v m 2 gt lt NS SmartMonitor 4 6 User s Manual OMRON Corporation Industrial Automation Company Application Sensors Division Sensing Devices and Components Division H Q Shiokoji Horikawa Shimogyo ku Kyoto 600 8530 Japan Tel 81 75 344 7068 Fax 81 75 344 7107 Regional Headquarters OMRON EUROPE B V Sensor Business Unit Carl Benz Str 4 D 71154 Nufringen Germany Tel 49 7032 81 1 0 Fax 49 7032 811 199 OMRON ELECTRONICS LLC 1 East Commerce Drive Schaumburg IL 60173 U S A Tel 1 847 843 7900 Fax 1 847 84
33. data from the respective controllers and performing the settings related to the measurements To display the settings or measured value of the sensor controller which is connected to the multi controller change the CH column on the display screen of the NS unit and select the channel CH number of the target controller Setting and displaying the following items can be implemented on the NS saqunivad SmartMonitor Displaying measured values Displaying measured values by plotting on the graph Performing the sensing setting Setting functions The contents of setting or displaying may differ depending on the types of controllers which monitor the measured values When the connection destination and monitor target is multi controller CH1 CH2 CH3 NS Unit Graph display available Sensing setting not available Line bright display not available To be monitored NS SmartMonitor User s Manual 1 9 Section 1 Operation procedure When the connection destination is a multi controller and monitor target is a sensor controller CH1 CH2 CH3 NS Unit Graph display not available Sensing setting available 8 Line bright display available f
34. dicated by brackets 5 a E Bi Visual Aids ale a Indicates points that are important to ensure full product performance such as operational precau tions and application procedures CHECK VA Indicates pages where related information can be found e Indicates information helpful in operation NS SmartMonitor User s Manual Introduction Editors Note MEMO NS SmartMonitor Users Manual Precautions for Safe Use 5 Precautions for Correct Use 5 Editor s Note 6 Page Format 6 Contents 9 Section 1 FEATURES 1 1 EI E AASLALASA S ALAAHA ALHLA1A29LLZLLALLLALRL ILZLS Features of NS SmartMonitor 1 2 System Configuration 1 3 Restrictions of NS SmartMonitor 1 6 Operating Environment for NS SmartMonitor 1 7 Operation procedure 1 8 Section 2 Startup and End 2 1 Starting up and Ending NS SmartMonitor 2 2 How to start up the NS SmartMonitor 2 3 NS SmartMonitor Automatic Start up Procedure 2 4 NS SmartMonitor Selection Start up Procedure 2 8 How to switch from the NS SmartMonitor to the user creation screen 2 13 Section 3 Operating Method 3 1 umm o l 8 Screen Layout 3 2 Monitoring Measured Value Main Screen 3 3 Displaying Measured value on the Graph Form Graph screen 3 6 Setting Sensing Items Sensing Setting Screen 3 9 Setting Controller Conditions Function Setting Screen 3 15
35. e 5 m To be monitored m S m When the connection destination is a sensor controller CH1 CH2 CHO NS Unit NS Unit To be monitored To be monitored Graph display available Sensing setting available Line bright display available Only connected Sensor Controller can be operated 5 Operating multi controller and sensor controller Displays the current measured value Various types of input related to the setting or measurement of the threshold value to the measured value can be implemented by operating keys on the respective controllers M Do not perform the key operations for the multi controller or sensor controller when using the NS SmartMonitor Do not perform bank switching by using the external input line The operations above may cause communication errors may cause malfunction of the NS SmartMonitor NS SmartMonitor 1 1 0 Users Manual Section 2 Startup and End Starting up and Ending NS SmartMonitor 2 2 How to start up the NS SmartMonitor 2 3 NS SmartMonitor Automatic Start up Procedure 2 4 9 NS SmartMonitor Selection Start up Procedure 2 8 How to switch from the NS SmartMonitor to the user creation 9 screen 2 13 m 2 NS SmartMonitor User s Manual 2 1 Section 2 Starting up and Endin
36. e NS unit and its system version where the NS SmartMonitor can be started up are described below Check your NS unit model and system version Model System version NS10 TVOL1 V1 6 02 or later 8 NS8 TV V1 6 02 or later S NS5 SQ0L V1 6 02 or later NS5 SQOL V2 6 20 or later m NS5 TQOL 2 6 20 or later 5 NS5 MQOLT V2 6 20 or later a 7 memory card CF is required to operate the NS SmartMonitor The memory card shall be separately prepared E Recommended memory card Model Memory size Memory types HMC EF172 15M Flash memory HMC EF372 30M HMC EF672 64M The memory capacity used by the system is approximately 12 M bytes About 600 K bytes are required to save the file of graph data CHECK It is necessary to prepare a memory card by taking into account the number of times graph data is saved NS SmartMonitor User s Manual 1 7 Section 1 Operation procedure Operation procedure This section describes an overall operation procedure 2 Copy the system program to a memory 4 Operating the NS card and insert the memory card to the omartMonitor___ NS unit NS Unit saqunivad 5 Operating Sensor Controller 3 Turning ON the power 1 Connection and wiring Connect the sensor head sensor controller multi controller and NS unit Refer to System C
37. een 3 3 Displaying Measured value on the Graph Form Graph screen 3 6 44 Setting Sensing Items Sensing Setting Screen 3 9 Setting Controller Conditions Function Setting Screen 3 15 System Menu 3 23 2 g 5 eR gt o NS SmartMonitor User s Manual 3 1 Section 3 Screen Layout Screen Layout The NS SmartMonitor displays the screens below to display the waveform by converting the displacement data from the ZS series controllers and performs the settings related to the measurements To switch to the respective screen press the Main Graph Sensing Setting Function Setting or Ver button on the upper part of the screen Main Screen Graph Screen ER rein v IT Bened The measured value status can Task Sat LD ON ZERO NABLE n E MESS Seve be displayed in a graph form Input zu Thrash ute eai ENS row Only data from the connected E controller be applicable Mess Value M 4 o o Kf c NEU H Threshold se Threshold set L138 3 6 158 UA E mur 2s 125 225 325 425 The current statuses of controllers Sensing Setting Screen such as measured value and of ipul and Gan fuer j The figure on the le
38. en Qa y Sensne Function y ngo Setting 5 _ Ji LD ON zERO CU External TASK1 input HIGH Pass Low BANK BANK 1 M Meas Value LABEL EHE c I Simultaneously press two corners out of four H Threshold L Threshold Set mm mm o D 3 c 5 Svsten VUuNE Exit N 2 PRTR Comm Speed 900 19200 38400 9800 19200 Data Bit NM Stop Bit 1 IE Parity Mone Even Odd PT Special Settings creen Write 2 Press the Special Screen button to display the System Menu Special Screen Special Screen Y Menu I Exit Special Function vj EE 3 Select the NS SYSTEM and press the START button NS SmartMonitor User s Manual 2 1 3 o et t m c E 5 m 5 2 14 Section 2 How to switch from the NS SmartMonitor to the user creation screen 4 The NS unit is reset and started up with the user creation screen VL To restart the NS SmartMonitor from the user creation Screen perform step 6 and then later Q in the NS SmartMonitor Selection Start up Procedure of the How to start up the NS e SmartMonitor perform this with the NS SmartMonitor Selection Start up Memory Card inserted CHECK NS SmartMonitor User s Manual Section 3 Operating Method Screen Layout 3 2 Monitoring Measured Value Main Scr
39. etting items refer to the User s Manuals of the multi controller and sensor controller Setting available items may differ between multi controller and sensor controller which are selected as target CH eac System settings p 3 17 Measure gt gt Key lock Lock elt Decimal place 3 M Save Settings EcoMode Normal Y s vum mer om Selection Language Japanese English Display Settings gt gt Undo Update 5 Functi Measure gt gt button Mein setne When the target CH mmm BANK BANK1 SA 9 ess SS n is a multi controller Select Input Grah 25 pom Ver D A p 3 17 TASKI me es lt lt Measure BANK BANK MEL 5 teh Y TASK2 Inputs None Y TASKI gt gt TASK3 10 gt gt Input None X TASK4 Measure gt gt button Select 1 0 Update When the target CH is a sensor controller Undo Update Men Graph cd oem J ver BANK BANK1 OH all button System settings 7 m NA Initialize settings Main Grah Sensing Function Ver Y Setting s Setting 3 19 Measure gt gt Initializes all settings BANK BONK 1 on controller System settings peris The contents ofa setting are saved id for a controller Save Settings Initialize all Initialize all Save Settings DHBANK Selection Displ Read
40. ft shows the Line breht 192 Sensing setting screen n be aspan gt g For details its functions refer ere connecung 10 Me multis to the User s Manual of your 2 22 the CH ied wm 383 controller Only data from the 5 can display the sensor controller qu p connected sensor controller can status be applicable z Stop 480 3 3 SensingSetting 3 9 Function Setting Screen z mum Jw The figure on the left shows the nenne BANK BANK 1 1 function setting screen gt sensum 512777 For details on its functions refer 2 Meme key WEIL uw the User s Manual of your In the case of Decimal place 346 Y controller communication error re ghean Ke oc Kae soten ue p 3 15 Press the EXE UA Write Version Information Display Screen wm men fuer UL This screen displays the NS SmartMonitor version information button NS SmartMonitor Verl O1 Copyright C OMRON Corporation 2004 2005 All Rights Reserved System Menu Communication Setting Screen System Nenu Exit This screen is used to set the communication settings such as the PORT A iie in Conn Speed 19200 38400 Smart Sensor connection destination ds 19000 port baud rate data length contrast D
41. g NS SmartMonitor Starting up and Ending NS SmartMonitor There are two methods to start up NS SmartMonitor E Using the NS unit exclusively for the NS SmartMonitor Starting up the NS unit with the NS SmartMonitor Automatic Start up Memory Card will start up the NS SmartMonitor Starting up the NS unit without the NS SmartMonitor Automatic Start up Memory Card starts up the user creation screen UA NS SmartMonitor Automatic Start up Procedure p 2 4 E Use by switching between the NS SmartMonitor and the user creation screen Operating the System Menu of the NS unit with the NS SmartMonitor Selection Start up Memory Card can switch between NS SmartMonitor and user creation screen Resetting the NS unit or turning OFF and then ON the power when NS SmartMonitor is running starts up the NS SmartMonitor o et t m c E 5 m 5 Resetting the NS unit once is necessary when switching between the NS SmartMonitor and user creation screen thus it is not possible to display the user creation screen and the NS SmartMonitor simultaneously Communication with a multi controller or sensor controller is available only when switching to the I m SmartMonitor Communication with a programmable controller is available only when switching to the user creation screen NS SmartMonitor Selection Start up Procedure p 2 8 How to switch from the NS SmartMonitor to the user creation screen p 2 13 NS Smart
42. ing Items Sensing Setting Screen 2x button Displays the vertical axis of the line bright display section in the range between Center location 160 to Center location 160 4x button Displays the vertical axis of the line bright display section in the range between Center location 80 to Center location 80 8x button Displays the vertical axis of the line bright display section in the range between Center location 40 to Center location 40 8 Specify measuring range screen This screen is used to set the start position and end position of the measurement area Measurement is performed only for the area when an area is specified This is effective when removing the impact from the phase which is irrelevant with the measurement Specifymeasuringrange Aree Ti en Start position _ Pressing a column displays the input pad for the End position value setting f a The operation above is available only in the 10 area setting mode wI Undo Execute Area Selects the display area for performing 2 measurement Operation is available only when the 2 area measurement setting is enabled Set and End buttons Switches between area setting mode and area monitoring mode When the Set button is pressed the mode is changed to the area setting mode and the setting area function becomes available The button display changes to En
43. inserting removing the memory card make sure that the NS unit power is turned m 5 e OFF a m 2 o 5 Connect the NS unit to the multi controller or sensor controller then turn ON the power of the NS unit 6 Press two corners simultaneously out of four on the touch panel screen to display the System Menu screen when the NS unit is in the operation mode or Connecting is displayed on the bottom right side on the screen e a itia us Comm Select Language PT Data BASS Simultaneously Settings Check Japanese _ press two corners J Project Special out of four Screen Hardware Password Check NS SmartMonitor User s Manual 2 9 o et t m c E 5 m 5 2 10 Section 2 How to start the NS SmartMonitor T Select Special Screen to display the Special Function on the second page 2 2 of the Special Screen by using gt lt buttons Special Screen Menu Exit Special Screen Y Menu I Exit 72 2 0 Alarm History Special Function Sort by Occurr Sort by Freq Operation Log Sort by Occurr Sort by Freq Device Honi tor Error Log Sort by Occurr Sort by Freq Com Test System Version 8 Select NS SmartMonitor in the Special Function and press the START button Special Screen Y Menu I Exit Special Screen Y Menu I Exit 2 2 qu
44. item display S Label be displayed by setting any characters 5 in 2 byte character and 10 in 1 byte CHECK character on the Function Setting Label setting screen UA Display setting p 3 22 External Input button This button is used to disable the external input line of the target CH controller and to enable the input buttons Care shall be taken when performing measurement using the external input line Pressing the External Input button switches the display as below Back LD OFF TIMING RESET ZERO Start Input Execut Execut LD OFF Start End button Pressing the Start button stops the laser emittance and switches to the End button Pressing the End button restarts the laser emittance and switches to the Start button TIMING Input button Controller enters into the timing input ON state while pressing the Input button RESET Execut button Controller enters into the hold reset ON state while pressing the Execut button ZERO Execut Cancel button Pressing the Execut button executes the zero reset process and switches to the Cancel button Pressing the Cancel button cancels the zero reset process and switches to the Execut button Back button Pressing this button enables the external input line and goes back to the CH TASK and BANK display ave Enabling the external input is necessary when switching to the Graph Sensing Setting or x Function Setting scree
45. itor automatic start up procedure using the example of the NS5 series 1 Copy the NS5SmartMonAUTO exe file on the NS SmartMonitor CD ROM to the hard disk in the PC 2 Double click the NS5SmartMonAUTO exe file which was copied to the PC The following directories and files are created NS5SmartMonAUTO BIN ETCSYS FGW FONT OTHER RUN SYS BankName txt datalog cfg DefBaseLDC ini DefBaseLDCR ini DefBaseMDC ini DefBaseMDCR ini EXTPROG1 LST Label txt mm txt omron hst print cfg SmartMon IPP time txt unit txt unitcom txt unitcom1 txt PNLPGOOO IPW PNLPGO001 IPW PNLPGO002 IPW PNLPGO003 IPW PNLPGO004 IPW PNLPGO005 IPW PNLPGO06 IPW PNLPGO007 IPW PNLPGOOA IPW PNLPGOOB IPW PNLPGOOF IPW PNLPGO10 IPW PNLPGFFE IPW PNLPGFFF IPW o et c o 3 m 3 NS SmartMonitor 2 4 User s Manual Section 2 How to start up the NS SmartMonitor 3 Copy the following folders and files in the NS5SmartMonAUTO directory to the root directory of the memory card NSSSmartMonAUTO BIN E BIN ETCSYS ETCSYS PNLPG003 IPW PNLPG003 IPW PNLPG004 IPW PNLPG004 IPW PNLPG005 IPW PNLPG005 IPW When drive E is assigned as a memory card 4 Turn OFF the power of the NS unit and insert the memory card described above to the memory card connector on the side of the NS unit E Before inserting removing the memory card make sure that the NS unit po
46. ivad Programmable Controller aur 2 Resetting the NS unit once is necessary when switching between the NS SmartMonitor and user Q creation screen thus it is not possible to display the user creation screen and the NS checa SmartMonitor simultaneously Communication with a multi controller or sensor controller is available only when switching to the SmartMonitor Communication with a programmable controller is available only when switching to the user creation screen NS SmartMonitor User s Manual 1 5 Section 1 Restrictions of NS SmartMonitor Restrictions of NS SmartMonitor The NS SmartMonitor and the SmartMonitor ZS for the PC cannot be used simultaneously Do not connect the SmartMonitor ZS for the PC to the USB of a multi controller or sensor controller while using the NS SmartMonitor Simultaneous connections of NS SmartMonitor and SmartMonitor ZS for the PC will cause a communications error and malfunctions of the NS SmartMonitor and SmartMonitor ZS for the PC Do not perform the key operations for the multi controller or sensor controller when using the NS SmartMonitor Do not perform bank switching by using the external input line The operations above may cause communication errors or may cause a malfunction of the NS SmartMonitor saqunivad NS SmartMonitor 1 6 User s Manual Section 1 Operating Environment for NS SmartMonitor Operating Environment for NS SmartMonitor Th
47. lay Displays the Present Value Incident Level and LD Power Present Value Displays the distance of sensing result for the measurement target area INC LEV Incident Level Displays the received light amount of the sensing result for the measurement target area LD PW LD power Displays the emitted light intensity of the present sensor head o 2 et gt o 5 Line Bright Display Displays line bright data by plotting it on a graph Line bright 64 128 192 255 O 64 128 192 255 168 Switching the graph display range in the horizontal direction by using the 64 128 192 and 255 buttons 64 button Displays the graph in the range between 0 and 64 of the Incident Level 128 button Displays the graph in the range between 0 and 128 of the Incident Level 192 button Displays the graph in the range between 0 and 192 of the NS SmartMonitor 3 1 0 User s Manual Section 3 Setting Sensing Items Sensing Setting Screen Incident Level 255 button Displays the graph in the range between 0 and 255 of the Incident Level The S bar indicates the start position of an area The E bar indicates the end position of an area A cross mark indicates the peak value in the line bright display 6 Start and Stop buttons Pressing the Start button starts to monitor the sensing state and the line bright data Pressing the Stop button stops
48. lue Character string input column Upper Gustum AAAAAAAAAAAAAAAA Pressing a column displays the virtual keyboard for the character input Undo button The Undo button is used to cancel the change of the setting contents Pressing the Undo button returns to the state upon opening the Function Setting screen or the final update state Update button The Update button is used to transmit the changed setting values to the controller of a target CH and update the setting values vue 2 Note that the contents of the change deleted when turning OFF the power of a controller even if Q the Update button is pressed and the target CH controller setting values are changed CHECK UA Save Settings p 3 20 NS SmartMonitor User s Manual Section 3 Setting Controller Conditions Function Setting Screen System Settings The System Settings screen is used to display a list of system setting values in the controller of the Target CH Changing the setting values and pressing the Update button enables the transmission of the contents of the change to the target controller The processing items which were changed from the setting contents in the controller of the Target CH are displayed in the red color Sensing Function Main X Greph X Setting X Setting Yer 71 lt gt 1 3 Switches the display items of system Measure gt gt settings Key lock Lo
49. lues of the specified BANK number in the specified file to the currently selected BANK Select from which BANK number when reading the setting value if the setting values of more than one BANK numbers are written in file Displays a list of files saved on the Memory Card Selecting a file in the list and pressing the Select button can select a file to be overwritten NS SmartMonitor 3 20 User s Manual Section 3 Setting Controller Conditions Function Setting Screen E CH BANK Selection Selects the target CH and BANK for performing the function setting Switching between CH and BANK cancels the currently changed contents of CH and BANK X imer 9 BAKEANKI 04 1 System settings Measure gt gt Select CH 1 v Initialize all Selectbank 1 BANK Save Settings Display Settings gt gt 75 o 2 et NS SmartMonitor User s Manual 3 21 o 2 et gt o 3 22 Section 3 Setting Controller Conditions Function Setting Screen E Display setting Sets the label name and BANK name which are displayed on the NS SmartMonitor screen and number of digits of the measured values and threshold value for display These setting contents are not transmitted to the controller Pressing the button returns to the Function Setting System Settings screen AENA 77 77 Funetien Y Sets
50. med for clerical typographical or proofreading errors or omissions PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user s programming of a programmable product or any consequence thereof COPYRIGHT AND COPY PERMISSION This document shall not be copied for sales or promotions without permission This document is protected by copyright and is intended solely for use in conjunction with the product Please notify us before copying or reproducing this document in any manner for any other purpose If copying or transmitting this document to another please copy or transmit it in its entirety NS SmartMonitor User s Manual Introduction Precautions for Safe Use 5 a o E Precautions for Safe Use Please use this product according to the manuals of Program Terminal NS Series ZS MDC and ZS L Precautions for Correct Use Please use this product according to the manuals of Program Terminal NS Series ZS MDC and ZS L NS SmartMonitor User s Manual 5 Introduction Editors Note Edi te Page Format How to start up the NS SmartMonitor How to start up the NS SmartMonitor Files below are saved on the CD ROM for NS SmartMonitor Select the necessary file s according to the type of the NS unit to be used NS5SmartMonAUTO exe For the NS5 series NS SmartMonitor Automatic Start up NS5SmartMonEXT exe For the NS5 series NS SmartMonitor Selection Start up NS8SmartMonAU
51. n CHECK NS SmartMonitor User s Manual 3 5 o 2 et o 2 et gt o 3 6 Section 3 Displaying Measured value the Graph Form Graph screen Displaying Measured value on the Graph Form Graph screen The measured value status can be displayed in a graph form Only data from the connected controller can be applicable 1 2 3 4 5 1 2 8 9 10 3 ANK v TT BANI Y Set Save 4 start Thresh Scale Auto Wave 11 240 228 n E l 5 8 9 zo en gt 7 H Thres Timing 6 2s 12s 22s 32s 425 CH display Displays the channel number of the target controller which is connected to display the measured value in a graph form TASK display and TASK switch pull down menu This menu is used to select the task number of the controller to display the measured value in a graph form The target CH numbers differ between the multi controller and sensor controller When the target CH is a multi controller The task can be selected from the ranges between TASK1 to TASK4 and between Input A to Input I When the target CH is a sensor controller The task can be selected from the range between TASK1 to TASK3 AA About TASK p 3 3 BANK switch pull down menu This menu is used to select the BANK num
52. omRon Smart Sensor ZS PSW11 User s Manual 222 E TASKI e een IBN v Cat No SIE Introduction This manual provides information regarding functions performance and operating methods that are required for using the NS SmartMonitor When using the NS SmartMonitor be sure to observe the following The NS SmartMonitor must be operated by personnel knowledgeable in electrical engineering To ensure correct use please read theis manual thoroughly to deepen your understanding of the product Please keep this manual in a safe place so that it can be referred to whenever necessary 00 Application Considerations Please read o 8 EJ 621 1112 Contents Sui FEATURES 27441511772 Startup and End 2724150 Operating Method uonoes 145121 APPENDIX User s Manual Smart Sensor NS SmartMonitor ZS PSW11 5 E Introduction READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document before using the products Please consult your OMRON representative if you have any questions or comments WARRANTY OMRON s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year or other period if specified from date of sale by OMRON OMRON MAKES NO WARRANTY OR REPRESENTA
53. onfiguration for details on connection between controller and NS unit ta System Configuration p 1 3 For details on wiring refer to the User s Manual for the respective controller 2 Copy the system program to a memory card and insert the memory card to the NS unit Copy the system program on the CD of NS SmartMonitor to a memory card and insert the memory card to the NS unit ta Copying the system program to a memory card p 2 1 Recommended memory card p 1 7 3 Turning ON the power Turning ON the power of the sensor controller multi controller and NS unit The main screen is displayed when the communication with the sensor controller multi controller is normally established The following message is displayed when the communication could not be normally established Time out occurred during the data reception Are you sure you wish to continue You can check the communication setting when selecting No The System Menu Communication Setting screen is displayed when No is selected NS SmartMonitor 1 8 User s Manual Section 1 Operation procedure Check the communication settings such as the connection port for the sensor controller or multi controller baud rate and data length when the Communication Setting Screen is displayed UA Communication Screen Operation Method System Menu p 3 23 4 Operating the NS SmartMonitor The NS SmartMonitor is used to display the waveform by converting the displacement
54. or Head p NS Unit NS10 8 5 Settings for Sensor Controller can be modified using the NS Unit screen and measured values can be monitored E Sensor Controller Programmable Controller Programmable Terminal RS 232C Connection Cable ZS XPT2 saqunivad Port A or Port B Two ways of using the NS unit are provided one is the way to use exclusively for the NS SmartMonitor and the other is the way to use the NS unit by switching between the user creation screen and the NS SmartMonitor when connected to the programmable controller When using exclusively for the SmartMonitor Multi controller or NS Unit Sensor Controller Port A or Port B When using by switching between the NS SmartMonitor and the user creation screen No connections of the controller and programmable controller are changed Multi controller or NS Unit Sensor Controller Port B Programmable Controller NS SmartMonitor 1 4 User s Manual Section 1 System Configuration When using by switching between the NS SmartMonitor and the user creation screen Connections of the controller and programmable controller are changed according to the usage NS Unit Multi controller or Sensor Controller Programmable Controller saqun
55. or sensor controller PORT A POTE and the NS unit RS 232Ccommunication settings Comm Speed 19200 i 38100 The Special Screen button is not displayed when the 9600 19200 system is started up from the NS SmartMonitor Data Bit T 8 Automatic Start up Procedure Stop Bit 1 INE Parity None Even gt p 3 25 PT Special Settings Screen Write Key Press Sound ON OF apa2 Buzzer Sound ERRON O Communication Setting button S PT Settings 1 i Exit This screen is used to set the PT Settings 1 22 a button 1 2 rightness buzzer sound an z others gt a Back light High Middle Low o Wite 0 0 Special Screen Menu Exit The NS unit screen is changed to Special Screen be started up from the user button Special Function creation screen CA p 3 28 f NS SmartMonitor User s Manual 3 23 Section 3 System Menu System Menu Screen Display Method The System Menu screen is displayed when the communication cannot be established between the NS unit and a multi controller or sensor controller upon start up of NS SmartMonitor or it is displayed by pressing two corners simultaneously out of four on the screen while the respective screen of the NS SmartMonitor is displayed When communication cannot be established Check the items below when the System Menu screen is displayed upon the start up of N
56. rect characters are used for the file name Or there is not enough space in the Memory Card Set the file name using correct characters Delete unnecessary files in the LOG folder and SETTING folder in the memory card Failed to read file File in the memory card is broken Or eight or more characters are used for the file name Check the target file in the Memory Card Change the file name in the Memory Card Exceeding maximum limit The input data value is outside the range Input correct value within the range Exceeding minimum limit The input data value is outside the range Input correct value within the range Please check mode of operation Operating mode of controller is in the state other than RUN Set the controller operating mode to the RUN mode NS SmartMonitor User s Manual Section 4 Specifications External Dimensions Specifications External Dimensions RS 232C Cable for Connecting to a programmable controller or programmable terminal ZS XPT2 2000 150 Unit mm 100 x 10 10 pins Square 9 pins Square connector PVC insulated round cable 3 89 mm dia core Conductor cross sectional area 0 013 mm Insulator diameter 0 38 Controller side PT PLC side Fitting area 12 3 4 5 1 A RD RXD RD RXD gt 0 v m z gt lt
57. rmeasures Error Messages and Countermeasures ERROR Appears the Measured Value The main digital display section displays ERROR For more information refer to the User s Manual of the controller Error message list Display Details Page file load error Cause Memory card is detached from the NS unit Or memory card is broken Countermeasure Check whether or not the memory card for the NS SmartMonitor is inserted to the NS unit Check whether or not the system file for the NS SmartMonitor is correctly saved on the memory card An error occurred during macro execution Communication with a controller cannot be established Time out error occurred Communication with a controller cannot be established Check the items below 5 the cable connected correctly 15 the controller power turned ON 15 the controller operating mode set to the RUN mode Is the controller state normal s the controller simultaneously used with the SmartMonitor ZS for the PC 15 any external device other than the NS SmartMonitor connected Read error Reading the setting data failed Check whether the controller is applicable to the NS SmartMonitor or version number of the controller Write error Writing the setting data failed Check whether the controller is applicable to the NS SmartMonitor or version number of the controller Failed to save to a file Incor
58. rt position or End position by one The operation above is available only in the area setting mode Decrements the value of the selected position of the Start position or End position by 10 The operation above is available only in the area setting mode Area following selection Selects the 2 area following method for Undo button Execute button aur performing 2 area measurement The operation above is available only when Area 2 is selected Changes back to the previous area setting values Transmits the contents of the change for area setting and updates the setting values Note that the contents of the change are deleted when turning OFF the sensor controller even if the Execute button is pressed and the sensor controller parameters are changed CHECK UA Saving contents of the change p 3 20 NS SmartMonitor User s Manual 3 13 o 2 et Section 3 Setting Sensing Items Sensing Setting Screen 9 Sensing Setting The setting values related to the sensing can be changed on the Sensing Setting Screen The changed processing items are displayed in a red color Pressing the lt gt button switches the setting item page Basic setting items are displayed on the first page and the detailed sensing setting items such as the noise rejection level setting on the CMOS elemental device and the emitted light intensity control are displ
59. s error and malfunctions of the NS SmartMonitor and SmartMonitor ZS for the PC to occur When connected to a multi controller ZS MDC Sensor Head saqunivad Sensor Controller Multi controller E i i ii ii Controller Link Unit Programmable Controller Programmable Terminal ZS XCN RS 232C Connection Cable ZS XPT2 NS Unit NS10 8 5 Settings for Multi controllers and Sensor Controllers can be modified using the NS unit screen In addition the Multi controller operation results and Sensor Controller measured values can be monitored Port A or Port B The sensor controller can be directly monitored by selecting the target controller to be monitored when the NS SmartMonitor is connected to the multi controller To select the target controller specify the channel CH number which is assigned to the target controller For more information about the assignment of channel CH numbers refer to the ZS MDC User s Manual NS SmartMonitor User s Manual 1 3 Section 1 System Configuration When connected to a sensor controller ZS LDC Only the connected sensor controller can be monitored when the NS SmartMonitor is connected to the sensor controller Sens
60. save setting file isplay Settings gt gt CHBANK Selection Read file Save file Save Settings button 7 Display Settings gt gt JL poo ve iur X mue BANK OH CH BANK Selection 1 System settings REFS Sensing y Function Main Graph Ji Setting X Setting button Measure gt gt Select CH 1v Tr EAN EAN E Ne settin 1 3 21 Selectbank 1 BANK E Label setting Lae sein Mess Value ABEL Save Settings SEES pii Resolution ABEL Secum Digt number Present value ABEL setting Displa Display Settings gt gt Settings o button Ca 222 NS SmartMonitor User s Manual 3 1 5 o 2 et gt o 3 16 Setting Controller Conditions Function Setting Screen E Common Operating Method Each function setting item is configured with any of the selections by the radio button or from the pull down menu or direct input setting column Radio button Key lock Lock The currently selected setting value is displayed in a yellow color Selection from Pull down Menu Pressing the W button Big displays the pull down menu 8 The pull down menu is used 3dig to select a setting value p Decimal place Y Numeric value input column Hysteresis Pressing a column displays the input pad for the numeric va
61. the measured value and resolution on the Main Main Graph Ji X Setting Me screen and a label to be displayed on the label display d se eo column of the current value I ABEL Pressing a column displays mum mee p Present Value BEL DUC i x ion Sets names of the respective EMEN M 800700 Bank name setting lt lt Display BRNKT button seting Bank name setting a E BANK 1 Pressing a column displays Ei Bank 2 BANK the virtual keyboard for the Bank 3 BANK3 character input Digit number setting Bank 4 BANK4 N 7 N il Selects the number of digits for x Sensing Function Digit number the measured value threshold BANK CH setting BANK1 value and present value on the button Number of decimals Mai Label setting Odig 147 ain screen Bank name ud 147 5 mm setting 24 147 48 ELM 140 484 4 147 4836 5 die 147 48365 mm Sde 147 485647 Select the number of digits by pressing a button NS SmartMonitor User s Manual Section 3 System Menu System Communication with controllers and settings related to NS unit hardware such as touch panel and LCD are performed on the System Menu screen Screen Transition on the System Menu Screen System Menu Exit The virtual keyboard is used to set the port which Exit connects to the multi controller
62. time mm minute ss second Enter a time by the 24 hour format Example To enter 6 o clock pm 1 minute and 1 second Enter 18 1 1 It is not necessary to fill a space by zero Pressing the ENTER button reflects the setting contents 6 Write button Pressing the Write button enables the setting changes of touch switch input sound buzzer sound and backlight brightness NS SmartMonitor User s Manual 3 27 o 2 et gt o 3 28 Section 3 System Menu Special Screen Special Screen Menu Exit Special Function T 4 vj 0 1 START button The START button is used to change the start up conditions of NS unit and reset it 447 The user creation screen can be started up under the state that the memory card where the NS SmartMonitor for the start up selection is saved is inserted to the NS unit when the start up Eie selection switched to the user creation start up To start up the NS SmartMonitor selecting NS SmartMonitor from the Special Function on the System Menu Special Screen screen of the user creation screen is necessary NS SmartMonitor User s Manual Section 4 APPENDIX Error Messages and Countermeasures Specifications and External Dimensions Index 4 2 4 3 4 5 NS SmartMonitor User s Manual 4 1 gt 0 v m z 4 2 Section 4 Error Messages and Counte
63. ulations that apply to the combination of products in the customer s application or use of the product At the customer s request OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product machine system or other application or use The following are some examples of applications for which particular attention must be given This is not intended to be an exhaustive list of all possible uses of the products nor is it intended to imply that the uses listed may be suitable for the products Outdoor use uses involving potential chemical contamination or electrical interference or conditions or uses not described in this document Nuclear energy control systems combustion systems railroad systems aviation systems medical equipment amusement machines vehicles safety equipment and installations subject to separate industry or government regulations Systems machines and equipment that could present a risk to life or property Please know and observe all prohibitions of use applicable to the products NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS AND THAT THE OMRON PRODUCT IS PROPERLY RATED AND
64. wer is turned e OFF Check the system security before performing the operations such as turning ON OFF the o et t m c E 5 m 5 CHECK power and pressing the reset switch Do not turn OFF the power of the NS unit or remove the memory card while accessing the memory card 5 Connect the NS unit to the multi controller or sensor controller then turn ON the power of the NS unit The following start up screen is displayed Select the language to be displayed on the NS SmartMonitor screens After selecting the language when the ZS series controller has been started up press the OK button according to the instructions displayed on the screen After the ZS series controller has been started up press the 0K button XThe controller startup has been completed when a measurement value is displaved at the main digital section OK r amp aBi HR Select Languge 28 _ S amp amp Englich MES When the NS SmartMonitor starts up characters are displayed on the screen in the previously selected language 5 When the NS SmartMonitor starts up for the first time the start up screen is displayed in CHECK English Selecting the Japanese button switches the screen display to Japanese NS SmartMonitor User s Manual 2 5 Section 2 How to start the NS SmartMonitor 6 The NS SmartMonitor program is executed and the Main Screen below is displayed
65. with the specified name in the Setting folder on a memory card Single byte alphanumeric characters underscore dollar mark and period can be used for the file name B Vi Sensing yo Function Man Gre Y etin ver BANK BANK1 CH 1 Saves data to prevent the setting contents from being nu The contents ofa setting re saved deleted even when turning OFF the power of the r controller controller Initialize all Save Settin Sets the file name without extension within eight Save Settes Read save setting file characters PURANA Read fle Save fie Characters ini are automatically added as an extension Display Pressing a column displays the virtual keyboard for the senez character input Y Back Back a No of fil z setting ini 13 04 2005 04 00 56 setting3 ini 18 04 2005 84 81 18 5 o BANKI BANK2 ae BANK3 BANK4 Execute Read Displays a list of files saved on Saves the setting values the Memory Card to the specified file Selecting a file in the list and pressing the Read button can select a file to be overwritten Selecting a BANK number is available when saving the setting values Back No of files settingl ini 19 04 2005 4 00 40 setting ini 13 04 2005 04 00 56 3 setting3 ini 13 04 2005 04 01 10 FILENAME cettingl ini LX BANK3 BANK4 710 Select Execute Cancel Reads the setting va

User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents