FEBC-5950 User's Manual
Contents
1.2. Copyright The documentation and the software included with this product are copy righted 2006 by ShenZhen JHC Technology Co Ltd All rights are reser
3. 226 3 eld Ld VHO Hardware Installation 2 1 Introduction The following sections show the internal jumper settings and the external connectors and pin assignments for applications 2 2 Jumpers and connectors FEBC 5950 Embedded Box Computer consists of SBC Single Board Computer board that is housed in an aluminum plate chassis Your HDD and SDRAM are all readily accessible by removing the aluminum bottom cover Any maintenance or hardware upgrades can be easily completed after removing the bottom cover Warning Do not remove any mechanical parts until you have verified that no power is flowing within the Embedded Box Computer Power must be switched off and the power cord must be unplugged 2 2 1 Setting Jumpers You can configure your FEBC 5950 to match the needs of your application by setting the jumpers A jumper 15 the simplest kind of electrical switch It consists of two metal pins and a small metal clip often protected by a plastic cover that slides over the pins to connect them To close a jumper you connect the pins with the clip To jumper you remove the clip Sometimes a jumper will have three pins labeled 1 2 and 3 In this case you would connect either pins 1 and 2 or pins 2 and 3 open closed closed 2 3 The jumper settings are E EN in a manual as follows
4. a 25 3 2 1 ACPI Power Management Configuration 25 23 2 2 asetus 26 202 9 CPI o eie eie ke ea TSn Kasa 27 3 24 SATA Conf eura oe ed CR 28 dii oe ptr 30 USB OITIS ITA 31 Super ULATION asus dh dte 32 9 250 PC Flealthi St atus Lebanese denis 33 2 2 9 Second super IO C Ong EALTOT 35 icis eti 37 MLO Se aitaa 38 3 3 1 System Agent SA 39 59 2 POCTPISIO CODD ENT ITON espe pistor E 39 SX Moro eT 40 SO S MIS EE 4 Solved FTT 42 S ONT dir jM 42 Driver TnstallatiOWiscc iier i 44 4 1 Follow the sequence below to install the drivers 45 TREO Mic 45 oo d Pium 46 eld Ld VHO General Information
5. DS 6 2 95 JUnper LO CANO ted etate 6 2 01 JPA Clear CMOS Dale 9 253 EZ USB POW rS 9 2 35 ALO POW Cl OM Se 6 Eoi esu eripi 10 2 3 4 T COM 2 RS232 422 485 Select en cleaner 11 2 35 59 CONLICOM2 RS232 POWEL 13 2 50 Mimi PC Ie Sinal sama s digestum dogm ERE Ens 14 2 9 aa 14 2 3 8 Digital VO Connectors kasa ase nes e 15 2 5 2 Front PanckConmncctoF dto aca 16 2 3 105 APA POWer Connectors osaamassa tasaa 17 2 4 DO nete AO Duma nana Se 17 2 4 1 Ethernet Connector LAN sssusa ss n tete ie t vt lavat Un en mik 18 2 4 2 Power Input Connector Fete alakaa ak 19 24 UNE LT 19 247 COMI COntlectOf eken 20 2 4 5 COM3 COM4 COM5 COM06 21 24 0 DIO 21 BIOS S CUP 22 E T 24 amm
6. closed closed 2 3 of needle nose pliers may be helpful when working with jumpers If you have any doubts about the best hardware configuration for your application contact your local distributor or sales representative before you make any changes 2 3 Jumper Location The FEBC 5950 Embedded Box Computer has a number of jumpers inside the chassis that allows you to configure your system to suit your application The table below lists the functions of the various jumpers The table below shows the function of each of the board s jumpers USB Power Jumper 1 2 5V n sea 2 3 SVDU Bil Power Selection for JP 16 ahi Je i i 12 3v3 AEN n E mi 03 uw HH mlt OHT aeg 10 0 5 oo al tee JE a 23 3VDU mug Jami x _ s EI S 25 52 B m uy n m oe B jf 1 2 5V default WP 5655 I lt W E 2 EE 2 3 5VDU n TQUE a ee 4 T H JP8 11 Selection for COM 1 1 E E 2 JAg PE ERE mn E 5232 E TEKE H RS422 RS48 3 8 4 6 JE EERS 9 ee ee wrap M aan FG ce s E X Clear CMOS data JP14 Power Selection for COM 1 ieee ETS
7. Tex 9 1 2 Normal default RS232 Ostau 1324 E 9 2 3 Clear CMOS data WIth 4 JP13 Selection for COM 1 WW W N Ag Auto Power on JP7 1 RS232 Default WM t E ESKON 1 2 Power Button On Default RS422 Duplex RS485 2 3 AC In Power On 1 2 PCIEX1 BUS m DN 2 3 SATA BUS gn E w d JP12 15 Selection for COM 2 v jd aS RS232_Oefauit E gt a N RS422 RS485 Lm P Y Ee ris gt JP17 Selection for 2 N i W i il W Ins SEEN aide 3 RS232 33 28 8 44 2 at an ER EE o RS422 Duplex 34 ebug PORT DIO 11 m Jumpers Description 3 Pin Block 3 Pin Block 3 Pin Block Auto Power on Select 3 Pin Block 1 RS232 422 485 select 6 pin Block COM RS232 422 485 select 6 pin Block 2 pin Block Mini PCIe Power Select Headers _____ Name 7 Description Front Panel 000 Panel Front Panel header 11 pin block EATE Power 0 5 SATA Serial ATA Power Connectors 5 block Power 1 5 5 2 Keyboard Mouse Connector 9 pin block COM2 COM3 Serial port headers 9 pin block COM4 COM5 COM6 Digital I O Digital I O Connector 8 Pin block 2 3 1 JP4 Clear CMOS Date 3 W i 2 3 1 jg e W 1 2 On Normal default 3 2 1 2 3 On Clear CMOS Data If you encounter the following a
8. 1 1 Introduction FEBC 5950 is intelligent fanless embedded system powered by Intel 4th Generation Intel amp CoreTM processors with multiple I O interface and 2 5 HDD driver bay FEBC 5950 offers Ix VGA interface 2xGiga Lan ports 2xUSB3 0 ports 2xUSB2 0 ports 6xCOM ports 1xMini PCIe socket 4xPCI PCIE socket The FEBC 5950 supports two 2 5 SATA HDD driver bay 1IxmS ATA for storage options 1 2 Features Key features Aluminum case Fanless disign 4th Generation Intel amp CoreTM processors 2xDDR3 1333 1600 SODIMM max 1608 IxmSATA 2x2 5inch SATA HDD Ixminipcie mS ATA DC 9V 36V Wide voltage input VGA display 6COM 8DIO 2xIntel Gigabit Ethernet 4xPCI or 1xPCI E x16 3xPCI 1 3 Specifications 1 3 1 General CPU Intel CoreTM 13 4330T 4M Cache 3 0 GHz 35W Intel Pentium Processor G3220T 3M Cache 2 60 GHz 35W Intel Core 15 4670T Processor 6M Cache up to 3 30 GHz 45W BIOS AMI BIOS System Memory Up to 16G DDR3 1333 1600GHz SODIMM Watchdog Timer 255 level interval timer setup by software Serial Ports 4x RS 232 2 x RS 232 422 485 DIO 8 bit DIO 058 2 x USB 2 0 compliant Ports 2xUSB3 0 compliant port Expansion Interface Support up to 1 x full size Mini PCle 4xPCI or 1xPCI E x16 3xPCI Storage Supports 1 5 SATA Support 2x 2 5 SATAII HDD 1 3 2 Display Chipset Intel HD Graphics Display Memory Shared system memery
9. or which have been subject to misuse abuse accident or improper installation JHC assumes no liability under the terms of this warranty as a conseguence of such events Because of JHC s high quality control standards and rigorous testing most of our customers never need to use our repair service If an product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed JHC products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain an RMA return merchandise authorization number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date 15 not eligible for warranty service 5 Write the RMA
10. 485 JP18 24 6 13 S292 default 246 135 3 5 5V 4 6 12V On 68 RS232 with power ts COM 1 RS232 422 485 i33 3 135 1 3 RI 2 4 DCD On 3 5 5V 4 6 12V 8D 2 4 pco 5V 4 6 12 On RS2 efau RS232 with power JP14 for COM 1 and JP18 for COM 2 are used to configure the Serial COM ports to pure RS232 or RS232 with power 13 2 3 6 Mini PCle Signal Select 3 1 1 4 7 10 2 5 8 11 On PCIe default 12 10 3 1 2 5 8 11 3 6 9 12 On mSATA JP9 is used to select the Mini PCIe signal PCIe or mSATA 2 3 7 Mini PCIe Power Select 3 2 1 2 3 3 3V standby default JP6 is used to select the power supplied with the Mini PCle 14 2 3 8 Digital I O Connectors Digital I O Connector Mai E Digital I O The 8 bit Digital I O connector provides powering on function to external devices that are connected to the connector Digital I O Connector 15 2 3 9 Front Panel Connector Front PWR LED Panel HDD LED PWR BTN HDD LED HDD LED This LED will light when the hard drive is being accessed RESET SW Reset Switch This switch allows you to reboot without having to power off the system PWR BTN Power Switch This switch is used to power on or off the system PWR LED Power Standby LED When the system s power is on this LED will light When the system is in the 51 POS Power On Suspend stat
11. 6789 Figure 2 8 COM3 COMA Connector ES 2 6 COM3 6 Serial Port Pin Assignments a Name RxD TxD DTR GND DSR RTS CTS RI 4 CO I DI A 2 4 6 DIO Connector Digital I O Connector 5 DIO GND 21 eld Ld VHO BIOS Setup Overview The BIOS is a program that takes care of the basic level of communication between the CPU and peripherals It contains codes for various advanced features found in this system board The BIOS allows you to configure the system and save the configuration in a battery backed CMOS so that the data retains even when the power is off In general the information stored in the CMOS RAM of the EEPROM will stay unchanged unless a configuration change has been made such as a hard drive replaced or a device added It is possible that the CMOS battery will fail causing CMOS data loss If this happens you need to install a new CMOS battery and reconfigure the BIOS settings Note The BIOS is constantly updated to improve the performance of the system board therefore the BIOS screens in this chapter may not appear the same as the actual one These screens are for reference purpose only Default Configuration Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any action
12. Super IO Watchdog Timer Sets the timeout value of the super IO watchdog timer 0 means disabled Serial Port Configuration and Serial Port 1 Configuration 32 Sets parameters of serial port 0 A and serial port 1 B Aptio Setup Utility Copyright 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Serial Port Enables or disables the serial port COM Change Settings Selects the IO IRQ settings for the super I O device 5485 Auto Flow Sets the RS485 auto flow for the serial port 3 2 8 PC Health Status This section displays the hardware health monitor 33 Aptio Setup Utility Copyright 2012 American Megatrends Inc Smart Fan Function Version 2 15 1236 Copyright 2012 American Megatrends Inc Smart Fan Function Aptio Setup Utility Copyright 2012 American Megatrends Inc CPU Smart Fan 1 Control Enabled Version 2 15 1236 Copyright 2012 American Megatrends Inc CPU Smart Fan Control When this feature is set to Automatic the CPU s fan speed will rotate according to the temperature The higher the temperature the faster the speed of rotation System Smart Fan Control When this feature is set to Automatic the System
13. USB UHCI Rev 2 0 compliance The USB inter face can be disabled in the system BIOS setup The USB interface connector is used for connecting any device that con forms to the USB interface Many recent digital devices conform to this standard The USB interface supports Plug and Play which enables you to connect or disconnect a device whenever you want without turning off the computer 19 Figure 2 6 USB connector Table 2 4 USB Connector Signal name VCC USB USB P0 GND 2 4 4 COMI COMJ2J2 Connector The FEBC 5950 provides two D sub 9 pin connector which offers two RS 232 422 485 serial communication interface port of COMI and 2 The default setting of COMI 2 is RS 232 Please refer to Table 2 5 for their pin assign ments and jumper settings for setting up RS 422 and RS 485 1 234 5 OOOOO OOOO Table 2 5 COM1 2 Serial Port Pin Assignments RS 232 67 8 9 Figure 2 7 COM 1 COM2 Connector RS 422 RS 485 Signal Name Signal Name Signal Name DCD Rx DATA RxD DATA TxD NC DTR NC GND DSR NC RTS NC CTS NC 1 2 3 4 5 6 7 9 9 Note NC represents No Connection 20 NC 2 4 5 COM3 COM4 COM5 COM6 Connector The FEBC 5950 provides Four RS 232 ports by two D sub 9 pin con nectors Please refer to Table 2 6 for their pin assignments 123 4 5 OOOOO OOOO
14. VGA Resolution up to 1920x1200 pixels with 24 bit color 60Hz 1 3 3 Ethernet Chipset 1 WGI210 Gigabit Ethernet 1x Intel 1217 Gigabit Ethernet Phy Speed 10 100 1000 Mbps Interface Up to 2 x RJ45 1 3 4 Power Consumption Input Voltage DC 9 36V Power Adapter AC to DC 19 V 6 32 A 120 W 1 3 5 Power Requirement System power Minimum power input DC 12V 5A 1 4 Environmental Specifications Operating temperature 10 55 C With extended temperature mSATA devices amp 0 509 C With standard temperature mSATA amp HDD devices Relative humidity 95 40 C non condensing Storage temperature 20 70 40 185 F Vibration loading during operation With SSD mSATA 3 Grms IEC 60068 2 64 random 5 500 Hz 1 hr axis 1 5 Mechanical Specifications EMC CE FCC Class A FEBC 5950 Dimensions 205 2 244 4 USB USB Gn o s Jo o 225240 DC 9V 36V TSG FEBC 5950
15. incorrect field values may cause the system to malfunction Aptio Setup Utility Copyright C 2012 American Megatrends Inc gt ACPI Power Management Configuration Version 2 15 1236 Copyright 2012 American Megatrends Inc 3 2 1 ACPI Power Management Configuration This section is used to configure the ACPI power management 25 Aptio Setup Utility Copyright C 2012 American Megatrends Inc Resume by PME Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Resume by PME Enables this field to use the PME signal to wake up the system Resume by Ring Enables this field to use the Ring signal to wake up the system Resume by RTC Alarm When Enabled the system uses the RTC to generate a wakeup event 3 2 2 Trusted Computing This section configures settings relevant to Trusted Computing innovations 26 Aptio Setup Utility Copyright 2012 American Megatrends Inc Security Device Support Disable Version 2 15 1236 Copyright C 2012 American Megatrends Inc Security Device Support This field is used to enable or disable BIOS supporting for the security device O S will not show the security device TCG EFI protocol and INTIA interface will not be available 3 2 3 CPU Configuration This section is used to configure the CPU It will also display the detected CPU information 27 Aptio Setup Utility Copyright C 2012 American Megatrends Inc Hyper threa
16. number visibly on the outside of the package and ship it prepaid to your dealer II Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Please contact your local supplier for ordering information Test conditions for passing included the eguipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recommend the use of CE compliant industrial enclosure products FCC Class A Note This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area 15 likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Technical Support and Assistance Step 1 Visit the JHC web site at www jhctech com cn where you can find the latest in
17. standard RJ 45 jack connector with LED indicators on the front side to show its Active Link status Green LED and Speed status white LED Table 2 2 for pin assignments Figure 2 4 Ethernet Connector Table 2 2 RJ 45 Connector pin assignments 10 100 1000BaseT Signal Name TX 10 100 BI DA GHz TX 10 100 BI DA GHz RX 10 100 BI DB GHz 18 BI DC GHz BI DC GHz RX 10 100 BI DB GHz BI DD GHz BI DD GHz Note NC represents No Connection 2 4 2 Power Input Connector DC IN The FEBC 5950 comes with a DC in power jack 3 pole Phoenix terminal block that 9 56V external power input Please refer to Table 2 3 for their pin assignments N f N A if NN r EUAN KIAN f 7 NV AN V d wx A f y VV JLY SS PA A 2 Figure 2 3 Power Conector Table 2 3 Power Connector Pin Assignments Pin Signal Name 2 V TAK 3 V YR 1E 2 4 3 USB 2 0 Connector The FEBC 5950 can support up to five USB interface connectors By default it provides two USB interface connectors located on the front metal faceplate and an additional three USB interface connectors can be supported through adding the Dual USB Cable Bracket These USB interface connectors give complete Plug amp Play and hot swap capability for up to 127 external devices The USB interface complies with
18. system back on after a power failure occurs the system may not power on if the power lost is resumed within 5 seconds power flicker 10 2 3 4 1 COM 2 RS232 422 485 Select JP15 12 17 2 RS232 422 485 2 1 9 O O N het 1 RS232 422 485 5 11 These jumpers allow you to configure the Serial ports to RS232 RS422 Full Duplex or RS485 JP8 JP11 and JP13 are used to configure the Serial COM port 1 JP 12 JP15 and JP17 are used to configure the Serial COM port 2 The pin functions of Serial ports 1 and 2 will vary according to these jumpers setting Note 45 When 1 RS232 422 485 is selected 2 11 and JP13 must be set in accordance to And when COM 2 RS232 422 485 is selected JP15 and JP17 must be set in accordante to JP12 11 ON on ON ON s y n ON ON ON va o EZ pum i n amp m tO E SB Poa a P P E S BS P E P da a s 8 B y P SG E E E E E E E E D E D N ET P 9 E 38 55 N 5 2 5 D an coxa B yc e EN Ao 6 2 24 k S S19 Sl4 T 45 QNS 5 2 8 qx amp N s WT 52 12 2 3 5 1 COM 2 RS232 Power Select COM 2 RS232 422
19. CMOS data becomes corrupted b You forgot the supervisor or user password you can reconfigure the system with the default values stored in the ROM BIOS load the default values stored in the ROM BIOS please follow the steps below 1 Power off the system and unplug the power cord 2 Set JP4 pins 2 and 3 to On Wait for a few seconds and set JP4 back to its default setting pins 1 and 2 On 3 Now plug the power cord and power on the system 2 3 2 JP1 2 USB Power Select 3 2 1 1 2 On 5V USB 1 2 default JP1 2 E 1 e 2 3 5V standby USB 8 9 JP2 321 321 1 2 On 45V 2 3 On default 5V standby JP2 are used to select the power of the USB ports Selecting 5V standby will allow you to use a USB device to wake up the system Important If you are using the Wake On USB Keyboard Mouse function for 2 USB ports the 5V standby power source of your power supply must support gt 1 5A For 3 or moreUSB ports the 5V standby power source of your power supply must support 22 2 3 3 Auto Power on Select 1 2 On Power on via power button default 3 2 1 2 3 On Power on via AC power JP7 is used to select the method of powering on the system If you want the system to power on whenever AC power comes in set JP7 pins 2 and 3 to On If you want to use the powerbutton set pins 1 and 2 to On When using the JP7 Power On feature to power the
20. FEBC 5950 User s Manual FEBC 5950 Aluminum case Fanless disign Ath Generation Intel Core processors Intel H81 Express Chipset 2xDDR3 1333 1600 SODIMM max 16GB 1xmSATA minipcie 2 2 5inch SATA HDD DC 9V 36V Wide voltage input VGA display 6COM 8DI0 2XIntel Gigabit Ethernet I210 amp I217 AxPCI 1xPCI E x16 3xPCI 4 4 4 4 4 4 4 1 2 3 4 6 6 1 8 9 SSS SY
21. TA Mode Selection Version 2 15 1236 Copyright C 2012 American Megatrends Inc When AHCI mode is selected in the SATA Mode Selection it will display the following information 29 Aptio Setup Utility Copyright 2012 American Megatrends Inc SATA Mode Selection Version 2 15 1236 Copyright C 2012 American Megatrends Inc SATA Controller Speed Indicates the maximum speed that the Serial ATA controller can support Port 0 Port 1 mSATA Port CFAST Port Enables or disables these Serial ATA ports Hot Plug Designates the serial ATA port as hot pluggable 3 2 5 PCH FW Configuration This section is used to configure the parameters of Management Engine Technology Aptio Setup Utility Copyright 2012 American Inc gt Firmware Update Configuration Version 2 15 1236 Copyright C 2012 American Megatrends Inc 30 Firmware Update Configuration Enables or disables the Me FW Image Re Flash function Aptio Setup Utility Copyright 2012 American Megatrends Inc Me FW Image Re Flash Disabled Version 2 15 1236 Copyright 2012 American Megatrends Inc 3 2 6 USB Configuration This section is used to configure USB Aptio Setup Utility Copyright C 2012 American Megatrends Inc Legacy USB Support Enabled Version 2 15 1236 Copyright 2012 American Inc Legacy USB Support Enabled Enables legacy USB Auto Disables support for legac
22. ding Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Hyper threading Enables this field for Windows XP and Linux which are optimized for Hyper Threading technology Select disabled for other OSes not optimized for Hyper Threading technology When disabled only one thread per enabled core is enabled Active Processor Cores Number of cores to enable in each processor package Intel Virtualization Technology When this field is set to Enabled the VMM can utilize the additional hardware capabilities provided by Vanderpool Technology EIST This field is used to enable or disable the Intel Enhanced SpeedStep Technology 3 2 4 SATA Configuration This section is used to configure the settings of Serial ATA devices 28 Aptio Setup Utility Copyright 2012 American Inc SATA Controller s Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc SATA Controller s This field is used to enable or disable the Serial ATA devices SATA Mode Selection The mode selection determines how the SATA controller s operates IDE Mode This option configures the Serial ATA drives as Parallel ATA storage devices AHCI Mode This option allows the Serial ATA devices to use AHCI Advanced Host Controller Interface When IDE mode is selected in the SATA Mode Selection it will display the following information Aptio Setup Utility Copyright 2012 American Megatrends Inc SA
23. e it will blink every second When the system 15 in the 53 STR Suspend To state it will blink every 4 seconds Pin Pin Assignment Pin Pin Assignment 3 HDD Power 2 LED Power Signal PWR LED 4 LED Power 7 Ground 6 Signall RESET SW 9 RST Signal 8 Ground 10 Signal 16 2 3 10 SATA Power Connectors These SATA power connectors supply power to the SATA drive Connect one end of the provided power cable to the SATA power connector and the other end to your storage device 2 4 indication Rear view 17 Nee eee S amp A 5 oye Oy LEKI 9 To Embedded Technolo 21 5 RTI 5 a eee yes FEBC 5950 SS o 8 g FAX FW o o BY I HS oe pL 21 5 20 gt e B 2 4 1 Ethernet Connector LAN The FEBC 5950 is equipped with two Intel WGI210IT for 10 100 1000Mbps Ethernet controllers The Ethernet port provides a
24. ettings Selects the IO IRQ settings for the super I O device RS485 Auto Flow Sets the RS485 auto flow for the serial port 3 2 10 Network Stack This section is used to enable or disable UEFI network stack 21 Aptio Setup Utility Copyright 2012 American Megatrends Inc Network Stack Disabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc When Network Stack is enabled it will display the following information Aptio Setup Utility Copyright C 2012 American Megatrends Inc Network Stack Enabled Version 2 15 1236 Copyright 2012 American Megatrends Inc 4 PXE Support When enabled Ipv4 PXE boot supports When disabled Ipv4 PXE boot option will not be created Ipv6 PXE Support When enabled Ipv6 PXE boot supports When disabled PXE boot option will not be created 3 3 Chipset This section configures relevant chipset functions 38 Aptio Setup Utility Copyright 2012 American Megatrends Inc System Agent SA Configuration Version 2 15 1236 Copyright 2012 American Inc 3 3 1 System Agent SA Configuration This section is used to configure the parameters of System Agent Aptio Setup Utility Copyright 2012 American Megatrends Inc Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 3 3 2 PCH IO Configuration This section illustrates the PCH parameters 39 Aptio Setup Utili
25. formation about the product Step 2 Contact your distributor sales representative or JHC s customer service center for technical support 1f you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages MI Contents General INTORMAN OM 1 LE MAROC COM sts 2 E TOI mrt Sua diu Mansin 2 IBS MEN Eo EUR 2 aan qm 2 9 2 saita 3 15 3 13 Power C ONSUIMPILOD e Kaken 3 FRE CUS Usate adu A utin 3 14 ny irOnmental SpecriCalOns doct hot ne dba Bo Etat bore 3 1 2 Mechanical e oar ce e a ebd Ue sace 4 Hardware Instat Eolo ei adi Eau idees huc ui 2 2 X InttOGCUC LOT ade 6 2 2 SMI CLS dnd CONDOS LODS kuumana 6 DI CUSTOM DOS mukanansa
26. le filesystem devices 43 44 eld Ld VHO Driver Installation The 5950 comes with a CD ROM that contains all drivers and utilities that meet your needs 4 1 Follow the seguence below to install the drivers Step 1 Install Chipset Driver Step 2 Install VGA Driver Step 3 Install LAN Driver Step 4 Install Audio Driver Please read instructions below for further detailed installations 4 2 Installation Insert the FEBC 5950 CD ROM into the CD ROM drive And install the drivers from Step 1 to Step 4 in order Step 1 Install Chipset Driver 1 Click on the Step 1 Intel Chipset Software Installation Utility folder and double click on the infinst autol exe 2 Follow the instructions that the window shows 3 The system will help you install the driver automatically Step 2 Install VGA Driver 1 Click on the Step 2 Intel Graphics Media Accelerator Driver Production Version folder and select the OS folder your system 15 2 Double click on the Setup exe file located 1n each OS folder 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically Step 3 Install LAN Driver 1 Click on the Step 3 Realtek folder and select the OS folder 2 Double click on the Setup exe file 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically Step 4 Install Audio Driver 1 Click on the Step 4 Rea
27. le fields not shown on the screen Use the up and down arrow keys to scroll through all the available fields Submenu When appears on the left of a particular field it indicates that a submenu which contains additional options are available for that field To display the submenu move the highlight to that field and press lt Enter gt AMI BIOS Setup Utility 3 1 Main The Main menu is the first screen that you will see when you enter the BIOS Setup Utility Aptio Setup Utility Copyright 2012 American Megatrends Inc System Language English 7 Version 2 15 1236 Copyright 2012 American Megatrends Inc System Time The time format is hour minute second The time is based on the 24 hour military time clock For example 1 p m is 13 00 00 Hour displays hours from 00 to 23 Minute displays minutes from 00 to 59 Second displays seconds from 00 to 59 System Date The date format is day month date year Day displays a day from Sun day to Saturday Month displays the month from January to December Date displays the date from 1 to 31 Year displays the year from 1980 to 2099 24 3 2 Advanced The Advanced menu allows you to configure your system for basic operation Some entries are defaults required by the system board while others if enabled will improve the performance of your system or let you set some features according to your preference Important Setting
28. ltek HD Audio Codec folder and select the OS folder your system is 2 Double click on Setup exe file located 1n each OS folder 3 Follow the instructions that the window shows 4 The system will help you install the driver automatically 45 46 XICINHdd V Watchdog Sample Code Software programming example MOV DX 4EH AL 87H OUT DX AL OUT DX AL MOV DX 4EH MOV AL 07H Ready to Program Logical Device OUT DX AL MOV DX 4FH MOV AL 08H Select Logical Device 8 OUT DX AL MOV DX 4EH MOV AL F1H Select watchdog timer register OUT DX AL MOV DX 4FH MOV AL 10H Set watchdog timer value OUT DX AL MOV DX 4EH MOV AL Select watchdog Control Register OUT DX AL MOV DX 4FH MOV AL 02H Set Watchdog Control Value OUT DX AL MOV DX 4EH MOV AL AAH OUT DX AL 47
29. ot to Launch PXE OpROM policy Controls the execution of UEFI and legacy PXE OpROM Launch Storage OpROM policy Controls the execution of UEFI and legacy storage ODROM Other PCI device ROM priority For PCI devices other than Network Mass Storage or Video defines which ODROM to launch 41 3 5 Security Aptio Setup Utility Copyright 2012 American Megatrends Inc Administrator Password Version 2 15 1236 Copyright C 2012 American Megatrends Inc Administrator Password Sets the administrator password User Password Sets the user password 3 6 Save amp Exit Aptio Setup Utility Copyright 2012 American Megatrends Inc Save Changes and Reset Version 2 15 1236 Copyright C 2012 American Megatrends Inc 42 Save Changes and Reset To save the changes select this field and then press lt Enter gt A dialog box will appear Select Yes to reset the system after saving all changes made Discard Changes and Reset To discard the changes select this field and then press lt Enter gt A dialog box will appear Select Yes to reset the system setup without saving any changes Restore Defaults To restore and load the optimized default values select this field and then press lt Enter gt A dialog box will appear Select Yes to restore the default values of all the setup options Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application Shellx64 efi from one of the availab
30. s There are few settings that you may need to change depending on your system configuration Entering the BIOS Setup Utility The BIOS Setup Utility can only be operated from the keyboard and all commands are key board commands The commands are available at the right side of each setup screen The BIOS Setup Utility does not reguire an operating system to run After you power up the system the BIOS message appears on the screen and the memory count begins After the memory test the message Press DEL to run setup will appear on the screen If the message disappears before you respond restart the system or press the Reset button You may also restart the system by pressing the Ctrl Alt and Del keys simultaneously Legends Keys Function Right and Left arrows Moves the highlight left or right to select a menu Up and Down arrows Moves the hightlight up or down between submenu or fields Esc Exit to the BIOS Setup Utility plus key Scrolls forward through the values or options of the highlighted field RESI Scrolls backward through the options of the highlighted Tab Select a field lt F1 gt Displays General Help lt F2 gt Pervious values lt F3 gt Optimized defaults lt F4 gt Saves and resets the setup program lt Enter gt Press lt Enter gt to enter the highlighted submenu 29 Scroll Bar When a scroll bar appears to the right of the setup screen it indicates that there are more availab
31. s fan speed will rotate according to the System s temperature The higher the temperature the faster the speed of rotation Boundary 1 to Boundary 4 The range is 0 127 Speed Count 1 to Speed Count 5 The range is 1 100 Case Open Sets this field to Enabled to allow the system to alert you of a chassis intrusion event 3 2 9 Second Super IO Configuration This section is used to configure the parameters of the system second super I O chip Aptio Setup Utility Copyright 2012 American Megatrends Inc gt Serial Port 0 Configuration Version 2 15 1236 Copyright 2012 American Megatrends Inc Serial Port 0 Configuration to Serial Port 3 Configuration Sets parameters of serial port O COM A to serial port 3 COM D 35 Aptio Setup Utility Copyright 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright C 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc 36 Aptio Setup Utility Copyright 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Aptio Setup Utility Copyright 2012 American Megatrends Inc Serial Port Enabled Version 2 15 1236 Copyright 2012 American Megatrends Inc Serial Port Enables or disables the serial port COM Change S
32. ty Copyright 2012 American Megatrends Inc PCI Express Configuration Version 2 15 1236 Copyright C 2012 American Megatrends Inc Onboard 1217 LAN Controller Enables or disables the onboard 217 LAN controller Onboard 1210 LAN Controller Enables or disables the onboard I210 LAN controller High Precision Timer Enables or disables the High Precision Event Timer 3 4 Boot Aptio Setup Utility Copyright 2012 American Megatrends Inc Setup Prompt Timeout Version 2 15 1236 Copyright C 2012 American Megatrends Inc Setup Prompt Timeout Selects the number of seconds to wait for the setup activation key 65535 0xFFFF 40 denotes indefinite waiting Bootup NumLock State This allows you to determine the default state of the numeric keypad By default the system boots up with NumLock on wherein the function of the numeric keypad is the number keys When set to Off the function of the numeric keypad is the arrow keys Quiet Boot Enables or disables the quiet boot function Boot Option Sets the system boot order Hard Drive BBS Priorities Sets the order of the legacy devices in the group 3 4 1 CSM Parameters Aptio Setup Utility Copyright 2012 American Megatrends Inc Launch CSM Enabled Version 2 15 1236 Copyright C 2012 American Megatrends Inc Launch CSM This option controls if CSM will be launched Boot option filter This option controls what devices system can be bo
33. ved ShenZhen JHC Technology Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of ShenZhen JHC Technology Co Ltd Information provided in this manual is intended to be accurate and reliable However ShenZhen Technology Co Ltd assumes no responsibility for its use nor for any infringements of the rights of third parties which may result from its use Acknowledgements Award is a trademark of Award Software International Inc PC AT PS 2 and trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corp RTL is a trademark of Realtek Semi Conductor Ltd other product names or trademarks are properties of their respective owners For more information on this and other JHC products please visit our websites at http www jhctech com cn Product Warranty 2 years warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by JHC
34. y when no USB devices are connected Disabled Keeps USB devices available only for EFI applications 31 USB3 0 Support Enable or disable the support of the USB 3 0 XHCT controller XHCI Hand off This is a workaround for OSes without the support of XHCI hand off The change of XHCI ownership should be claimed by the XHCI driver EHCI Hand off This is a workaround for OSes without the support of EHCI hand off The change of EHCI ownership should be claimed by the EHCI driver 3 2 7 Super IO Configuration This section is used to configure the I O functions supported by the onboard Super I O chip Aptio Setup Utility Copyright 2012 American Megatrends Inc Restore Power Loss Power Off Version 2 15 1236 Copyright C 2012 American Megatrends Inc Restore AC Power Loss Power Off When power returns after an AC power failure the system s power is off You must press the Power button to power on the system Power On When power returns after an AC power failure the system will automatically power on Last State When power returns after an AC power failure the system will return to the state where you left off before power failure occurs If the system s power 15 off when AC power failure occurs it will remain off when power returns If the system s power is on when AC power failure occurs the system will power on when power returns Watchdog Timer Unit Selects the watchdog timer unit second or minute
Download Pdf Manuals
Related Search