LED-192 RGB User Manual
Contents
1. Fine S Fixture Hours Display Normal d5P Display Inversion i dor uP Software Version III DMX 512 Address Setting Press the MENU button up to when the T is shown on the display Pressing ENTER 4D button and the display will blink Use DOWN and UP button to change the DMX 512 address Once the address has been selected press ENTER button to setup or automatically return to the main functions without any change after 10 seconds Back to the previous functions without any change press MENU button m g Mode Press the MENU button up to when the 90 is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select id i mode 1 or id g mode 2 press ENTER button to setup or automatically return to the main functions without any change after 10 seconds Back to the previous functions without any change press MENU button i You can set 4 Lights show nid You can set 16 Lights show Master Slave Mode Press the MENU button up to when the button Use DOWN and UP button to select the ASE Sl c Gl 2L iD Master mode Slave Mode 1 2 3 or 16 Press ENTER button to setup or automatically return to the main functions without any change after 10 seconds Back to the is shown on the display Pressing ENTER previous functions without any change press MENU button Show Mode Press the MENU button up to when the UP button to select the 54 i or G2. EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements Innovation Quality Performance 11D LED STROBE RGB LINKABLE STAND ALONE LED 192 RGB User Manual Please read the instructions carefully before use TABLE OF CONTENTS Safety Instructions Technical Specifications Main Function How to control the fixture DMX 512 Configuration DMX 512 Connections Troubleshooting Fixture Cleaning 1D 1 Check the connection of power and main fuse 2 Measure the mains voltage on the main connector B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to
3. Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the fixture Before operating ensure that the voltage and frequency of power supply match the power requirements of the fixture Its important to ground the yellow green conductor to earth in order to avoid electric shock Disconnect main power before servicing and maintenance Use safety chain when fixes this fixture Don t handle the fixture by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this In the event of serious operating problem stop using the fixture immediately Never try to repair the fixture by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Do not connect the device to any dimmer pack Do not touch any wire during operation and there might be a hazard of electric shock To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture The housing must be replaced if they are visibly damaged Do not look directly at the LED light beam while the fixture is on There are no user serviceable parts inside the fixture Do not
4. e display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again Display Inverse It is good for you to install the unit on the floor or under ceiling Press the MENU button up to SF is blinking on the display Use the ENTER button to change to the mode SF display normal It will ely store after 8 seconds Or press the ENTER button again return to the mode display inversion To go back to the functions press the MENU button i Or 4 Display normal mode for the fixture putting on the floor i Display i inversion mode for the fixture fixing under ceiling 1O OCI Software version Press the MENU button up to when the is blinking on the display Pressing ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU button again 6D
5. h SI press ENTER button to setup or automatically return to the main functions without any change after 10 seconds Back to the previous s shown on the display Use DOWN and functions without any change press MENU button Mi Manual Setting Press the MENU button up to when the lii button and the display will blink Use DOWN and UP button to select or Ge Pe or or An or Sted press ENTER button into submenu and use DOWN and UP button to change the lighteness or strobe frequency once the value selected press ENTER is shown on the display Pressing ENTER button to setup or automatically return to the main functions without any change after 10 seconds Back to the previous functions without any change press MENU button 5D _tr Blackout Mode Press the MENU button up to when the bid is shown on the display Use DOWN and UP button to select the Yes or No Blackout Back to the previous functions without any change press MENU button LED Press the MENU button up to when the is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the ON or OFF mode Once the mode has been selected press ENTER button to setup or automatically return to the main functions without any change after 10 seconds Back to the functions without any change press MENU button again Pott AV Fixture Hours Press the MENU button up to when the is blinking on th
6. high voltage cables that may cause damage or interference to DMX interface circuit C Some fixtures don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the fixture Set the proper address D No response to the sound 1 Make sure the fixture does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 8 Fixture Cleaning The cleaning of internal must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 10D 6 DMX512 Connections The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels o o 0 0 a o000 0o00 b e000 e eres o emen e emm o era 3 a o 2 2 COMMON DMX INPUT Termination reduces signal errorsand to avoid signal transmission
7. open the housing or attempt any repairs by yourself In the unlikely event your fixture may require service please contact your nearest dealer For power supply do not connect in series much more than 33 units use another mains supply for next 33 units 2D 2 Technical Specifications It can be operated by DMX512 control or can be used as an individual unit without controller It can be linked together as many as required in master slave mode and perform the great built in programmed lighting shows triggered by music Please use a 3 pin XLR cable plug when connecting them together lt features different pre programmed chase patterns Power supply Input Voltage 100V 240V 50 60Hz Power consumption 18W LED Total 192pcs Red 64pcs Green 64pcs Blue 64pcs Channels Ch 1 Red Ch 2 Green Ch 3 Blue Ch 4 Dimmer strobe Dimension 315mm x 181mm x 114mm Weight 2 1 kg 9 3 181 z amp a E OO O 8B BESO BHEOSBS ES Oo 8 G 8888 OG 8 6 o6G Og Bese e eae ea eocoseeeeehtes6a 6 oo 6 660 6868860 666 6 eeee00e800080 80000000000 eeoeoeeneooe8 eeoeeoaeoooaes eaeeoeoe0eaooog08 eaeeoo0eceoooes aeoeoeo0egoo0008 aeoeoeneooes oeeeoooeo00o a o 886 o To select any functions press MENU button until the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to 3D C Ea
8. problems and interference Itis always advisable to connect a DXM terminal Resistance 120 ohm 1 4W between pin2 DXM and pin3 DXM of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 5 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 7 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light 9D 1 Safety Introductions A WARNING Please read the instructions carefully which includes important information about the installation operation and maintenance
9. s normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only B DMX controller If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can LACEE DMX signal Press the MENU button up to when the AAT ig shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units cannas LA LU S LU S LU S 7D change the mode Once the required mode has been selected press ENTER button to setup or it will automatically return to the main functions without any change after idling 10 seconds Back to the functions without any change press MENU button The main functions are shown below DMX512 Address Setting Sid id i Mode 1 Md d Mode 2 GL fid Master Slave mode Red setting Green setting Ai lue setting gini MH en Dimmer setting age Strobe setting S Blackout Mode Yes Blackout 5 Blackout Mode No Blackout Lon LED on oF F LED off
10. sy Controller by CA 8 The easy remote control is used only in master slave mode There is a terminator for connect the easy controller inside the fixture By connecting the cable into DMX IN waterproof cable entry gland to the CA 8 terminator of the first fixture you will find that the remote control on the first fixture will control all the other fixtures for Stand by Function and Mode functions Blackout Blackout the unit Function 1 Strobe White Color Show 2 Strobe Multicolor 1 9 1 5 Sound LED Mode LED OFF LED ON Slow blinking 5 DMX512 Configuration DMX 512 Configuration CH4 Dimmer strobe 255 Open 247 nira s 200 Sound 170 8D 4 How to control the fixture Three ways of operation A Master Slave operation B DMX controller C Easy controller CA 8 A Master Slave operation By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated LA ae show This function is good when you Its DMX input jack will have ee plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode and select normal or DLI e 2 light show or SKI 3 3 light show or St lb 16 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show In slave mode means the unit work
Download Pdf Manuals
Related Search