Mini High Speed Dome Camera User Manual
Contents
1. Mini High Speed Dome Camera User Manual Contents 1 Introduction ESAS ias rad an 2 SPeCCihlCAtlONSiacdeacia eaten nenna a augue dbaaded E EEE 4 2 Installation Installation and Connetti soss cece cece ee eee cnn cnn teeta N 5 DIP SWItCMS Gt Pini tstati nas azeineecrat ans nas necnashattande ao enii danke 6 3 Operation Check points when power UP 0 eee eee ceiien oa ninii eri neia 8 A no ge Foes a E taeneteesacesties Fouts 10 Camera and Lens COntOll cc vice cicsscie cae dedine ala stan cab douse ade 10 4 How to use OSD Menu Basic operation of Main MENU scs seii bigein oea a reni 11 Main Meny IntiOductt OM cerci cora teriga araneae geeks EE AER case 11 System nfonmMatiOn ssns ase aE EE E A A EEES 12 ADDR SSN riren E a A AEN 13 MOON ir AAA AA 13 Pates ias 16 CAMA tna oa 17 Cruse StH Gta ndecsSer ceeceatoncd wisthtiemeeny acest dns ia 28 Display SetU colima cinco inicios dial 29 Restore Factory Detalltiuiininaiina a aa 29 REDOOL SY STC Mi andan 30 EX toos ase decades 30 5 Trouble Shooting Trouble SKOON anotarse oda eee eee 30 6 Safety Information Safety IO Mal daras 31 1 Introduction 1 1 Features X Camera Specifications e CCD Sensor 1 4 Interline Transfer CCD e Zoom Magnification 10X Optical zoom 10X Digital zoom e Day amp Nightfunction The camera is configured to switch to the black and white mode automatically under low light conditions and at night with mechanical IR Cut filter2. and normal when shutdown Sharpness adjust the sharpness of the edges Range 0 31 Sharpness Sharpness 8 Exit Hue adjust the image hue range 0 100 Re boot restart the camera Exit exit camera menu 4 2 6 Cruise Setting 28 CRUISE DWELL TIME lt SECS gt 6 PRESET LIST 1 10N 0 OFF 1234567890 PRESET 1101111111 1 10 BACK EXIT Auto cruise set up preset scan route lt Dwell Time Sec gt preset cruise dwell time range 1 250 Sec lt Preset List gt 3 pages 30 presets lt 1234567890 gt preset position in the preset list lt 110111 1111 gt 1 means the preset position corresponding to above preset list is elected to cruise list 0 means overleap lt Back gt save the setup and back to main menu lt Exit gt ExitOSD menu 4 2 7 Display Setup Display setup On Off set up the orientation display or not Horizontal Vertical Zoom 1 t 236 163 x1 4 2 8 Restore Factory Default Move cursor to lt RESTORE FACTORY DEFAULT gt and press Iris Open to restore factory default 29 4 2 9 Reboot System gt Move cursor to lt Reboot System gt and press Iris Open to reboot the system Easy to change the Soft Hard address by remote and no need to power off 4 2 10 Exit Move cursor to lt Exit gt and press Iris Open to exitthe OSD menu 5 Trouble Shooting Troubles Reason Solution No action no Conne
3. e Since the operation method can be different for each controller available refer to the manual for your controller if camera can not be controller properly 3 2 Operation Note The manual will refer to our CCTV tester to explain how to operate and control the camera 3 2 1 Preset function pre check e Check how to operate preset Scan Auto Pan and Pattern function with controller or DVR in advance to operate camera function using them refer to your System keyboard Manual e f controller or DVR has no pattern button or function use shortcut keys with preset numbers For more information refer to Reserved Preset in this manual e Use UP DOWN LEFT RIGHT direction key to move to a desired position then press Zoom Lens Iris to adjust the pictures e Press preset setup to input number then confirm by a press on setup key Call Preset e Press Call Preset key and input No of preset the confirm by a press on Setup key the camera will move to the desired preset meanwhile the zoom lens and iris will automatically change to preset states 3 2 2 Reserved Preset Some Preset numbers are reserved for direct access to specific functions in OSD menu These direct commands via preset provide quick execution of various functions using keyboard controller as well as simplify the interface with DVR and IP equipments Reserved Pres
4. from 1800K 10500K Indoor 3000 10 500K Outdoor 1 800 10 500K to ensure the most nature image effect Auto Trace WB Auto Trace WB mode Outdoor Exit 2 2 Manual Close auto WB adjust Red and Blue level manually Manual WB Red Ulla Blue LL ee besieged Exit Red adjust range 0 100 Blue adjust range 0 100 2 3 Auto BW This mode is the most accurate and reliable for most places 3 Backlight Compensation setup Backlight High Middle Low Off 4 Motion Detection setup Match the Alarm sensor input to one of preset positions If an external sensor is activated camera will move to corresponding preset position when this item is predefined Motion Detection Alarm On Off Select Region 1 Region Mode On Top 20 wrt EE Bottom EL scise eee Left 20 cell E Right Aucas lex Exit Alarm On Off Region 1 4 Region Mode On Off 5 Focus Setup Focus Mode Auto Zoom trace mode On Zoom trace speed Fast Digital Zoom On Show Zoom Off Initial Zoom Position Off Lens Initialization Exit 1 Mode Auto Manual One off Auto focus Press Iris Open to enter sub menu One off auto focus Once the image zoom changes the camera will automatically focus and fix the status till the image change again Notice do not use Auto Focus under the below conditions gt The target is too dark such as black clothes or curtains gt The target is very smooth
5. like car surface gt The brightness contrast of the target is not very clear gt Too strong high light or back light gt Too high contrast gt Some shade in front of the target 1 Auto mode setup Setup Zoom Zoom in Zoom out Back press SET key Using the direction keys to enlarge or downsize press Iris Open key to back 2 One off Auto focus and Manual focus Adjustment Setup Zoom 1 Zoom in 1 Zoom out lt Near Far Back press SET key 2 Zoomtrace mode Manual Focus Off Auto and One off Auto Focus On Off 3 Zoom trace speed Fast Slow 4 Digital zoom On Off range X2 X10 Digital Zoom Digital Zoom X2 Exit 5 Show zoom On Off 6 Initial zoom position Using direction keys to move the cursor to On then press Iris Open to set up Initial Zoom Position Initial Zoom Position X1 Exit Zoom range X1 X10 7 Lens Initialization press Iris open Set key to initialize the lens 8 Exposure setup Exposure Brightness 25 awe Iris Auto Shutter AGC Off SSNR Off SENS UP Off Exit Brightness range 0 100 Iris Auto Manual Press Iris Open to enter into manual setup Manual Iris Iris Exit If the number of iris is set to higher the image will be brighter 23 Shutter mode Flicker Manual Auto The shutter speed of
6. Anti flash is 1 100 NTSC 1 120 PAL Manual mode setting PAL 2X 4X 6X 8X 10X 12X 14X 16X 24X 32X 64X 128X 1 120000 1 60000 1 30000 1 10000 1 7000 1 5000 1 2500 1 1600 1 1000 1 700 1 500 1 250 1 100 1 50 Manual shutter Shutter 1 50 Exit Notice Auto shutter setting only for manual iris mode AGC High Middle Low Off Enhances image brightness automatically in case that luminance level of image signal is too low Range 5 41 AGC Level 5 Exit SSNR High Middle Low Off Enhances images by reducing noises when gain level of images too high Sens up Manual Off Adjust CCD exposure time Auto mode setting 2X 4X 6X 8X 10X 12X 14X 16X 24X 32X 64X 128X 24 9 Additional menu Additional menu User setup Off Privacy zone mask Off Day 8 Night Auto 1 Sync system Internal Image adjustment EXIT 1 JUser preset setup On Off User Preset User preset number No 1 User preset mode Off Save Clear Exit preset not setup 8 user preset number 1 8 User Preset mode use direction keys to On and press Iris Open to setup 25 User preset mode Focus Exposure Other Exit Focus Using direction keys to Focus and press Iris Open key to set up Focus Mode Auto Zoom trace mode On Zoom trace speed Fast Digital zoom On Show zoom Off Exit Other refer to
7. VERSION gt Shows current software version of camera Notice the system information can not be changed P 4 2 2 Address Setting ADDR SETTING ADDR TYPE HARD ADDR SOFT 3 ADDR HARD 1 BACK EXIT ADDR TYPE Choose the address type Hard Soft Add when you choose soft type the user can setup the add ADDR SOFT setup soft address Press UP DOWN keys of your controller and setup the camera ID from 0 254 ADDR HARD Setup hard address Only can be changed by DIP Switch Notice Please reboot the dome camera after reset the camera ID 4 2 3 Motion ress by remote access MOTION SET FRAME SCAN POWER UP PATTERN 4 PARK TIME 15S PARK ACTION PATTERN 4 FRAME SCAN SPEED 16 RNADOM SCAN SPEED 16 BACK EXIT Motion setup is to setup preset and packing action function SETFRAME SCAN setup the LEFT RIGHT extreme position between two presets POWER UP This function enables to resume the last action executed before power down NONE No action CRUISE Cruise action between presets position AUTO SCAN 360 continious scan RANDOM SCAN 360 intermittemt scan action FRAME SCAN PARK TIME Parking action during idle time Time setting 15 60 Seconds 2 60M Minutes 2 12H Hours PARKACTION This function enables to locate the camera to specific position automatically if operator doesn t operate the controller for a while The Park Time can be defined as an i
8. below details Other Camera Type Off BW Auto trace BW BLC Off Motion Detection Off Privacy mask Off Day amp Night Outer Horizontal flip Off Vertical flip Off Exit 26 2 Privacy mask Privacy mask Group selection 1 Area selection 1 Zone mode Off Color A A Top OO isd eda saeeine Bottom 104 2004 A Left A SAE Right OS An A Exit Group selection 1 8 Area selection 1 4 zone group Zone mode On Off Color color range of privacy zone is 0 100 Top ordinate position on the top of zone Bottom ordinate position on the bottom Left horizontal abscissa position on the left side Right horizontal abscissa position on the left side 3 Day Night Day and Night function Auto 1 Auto 2 Outer Color B amp W mode B amp W mode suit for night work Color mode suit for daytime Auto mode change day and night mode automatically according to the environment illumination Auto 1 is faster than Auto 2 27 4 Synchronous mode internal unchangeable 5 Image adjustment Image adjustment Freeze Off Horizontal flip Off Vertical flip Off Sharpness On Hue SO lissa Exit Freeze Camera starts freezing the image of start point as soon as camera stops at preset end point camera starts display live images Horizontal flip image will flip 180 when you start up Normal when shutdown Vertical flip image will slip 180 when you start up
9. ct wrong cable Correct the connection after power up Protocol and Baud rate image after Power supply damaged Change power on Bad connection Eliminate the bad connection Out of control Maybe ser setup wrong IF Reset IP Protocol and Baud rate RS 485 cable reverse connection or disconnection Check RS 485 connection cable Screen not stable Video cable is bad connection Eliminate the bad connection Power is not enough Change Discontinuity while work RS 485 cable is bad connection or disconnection Check RS 485 connection cable RS 485 cable broken Check RS 485 connection cable 30 6 Safety Information Transportation Do not force shake and marinate during transportation storage and installation Installation Please handle with care do not press the camera and its parts when you install do not connect before you install the cover Power cable Video cable and control cable Use shield wire and do not mix with other cables Electrical safety Keep the camera or signal transmission wire away from high voltage equipment or cable at least 50 meters take lightning protection and surge protection Clean When cleaning use dry and soft cloth or neutral cleanser to clean the camera cover 6 Must be sealed closely do not spray water or liquid onto parts of camera doing so may cause damage Do not use the ca
10. et Function Go Set Preset lt 95 gt Enters into OSD menu Go Preset lt 80 gt Reserved Go Preset lt 82 gt Runs cruise function Go Preset lt 83 gt Clean all presets Go Preset lt 84 87 gt Runs Pattern 1 4 Go Preset lt 88 gt Reserved Runs wide dynamic function Go Preset lt 89 gt Reserved Stop wide dynamic function Go Preset lt 96 gt Runs 360 scan pause 3 seconds per 90 Go Preset lt 97 gt Runs linear scan Go Preset lt 98 gt Runs cruise function Go Preset lt 99 gt Runs Auto pan function 3 3 Camera Lens control 3 3 1 Zoom Adjust the lens distance to enlarge or downsize the image for best effect or wide angle effect e Using ZOOM IN TELE key to enlarge the images e Using ZOOM OUT WIDE key to downsize the images 3 3 2 Focus Adjust definition of the object of scene e Press Focus Far key to shorten the distance of far scene e Press Focus Near key to shorten the distance of near scene 3 3 3 Iris Press Iris Open key to adjust the brightness 4 How To Use OSD Menu After power up or restart the present Protocol Baud rate and Address will be displayed on the screen as below PTOL PELCO P COMM 2400 N 8 1 ADDR 1 4 1 Basic operation of Main menu e Go lt Preset 95 gt to enter into main menu e Using Iris open and Iris close to confirm or exit main menu eUsing UP DOWN keys or joystick to move cu
11. for clear images e Various focus mode Auto Focus Manual Focus Semi Auto Focus X Powerful Pan Tilt Functions e Max 360 sec high speed Pan Tilt motion e Automatic turn over e Support bearing indication e Programmable cruise and presets e Soft address enables to set up the address and number of the camera e Adopt Vector Drive Technology Pan Tilt motions are accomplished in a shortest path As a result time to target view is reduced seriously and the video on the monitor is very nature to watch e For jog operation using a controller since ultra slow speed 0 05 sec can be reached Itis very easy to locate camera to desired target view e Support zoom proportional Pan Tilt speed Camera can be moved to a desired position in accurate manner even through high zoom ratio X Preset Linear Preset position cruise Pattern Auto Scan e Max 256 presets are assignable and characteristics of each preset can be set up independently e Linear scan enables to move camera repetitive between two preset positions with assigned speed e Preset position cruise the group can have max 30 entities of preset This enables for camera to move a combinations of this functions repetitively 2 4 Patterns with 100 commands can be recorded and executed This enables the camera to track a surveillance trajectory as closely as possible e 360 continuous scan e 360 intermittent scan The camera will have seconds st
12. mera in extreme temperature or humidity environment Do not install the camera close to air outlet of air condition Camera lens will be misty because of water condensation under below conditions Extreme temperature change The room full of smoking or dust Do not locate the camera towards extremely bright objects such as sun and spotlight as this may damage the CCD image sensor es 31
13. nterval FRAME SCAN SPEED Set the speed between two presets from1 32 RANDOM SCAN SPEED set the speed of 360 continuous and intermittent scan 14 Set Frame Scan FRAME SCAN SET SCAN POSITION CLEAR FRAME SCAN BACK EXIT SET SCAN POSITION Set up scan range between two positions Left Right extreme position CLEAR FRAME SCAN Deletes frame scan 1 Set Scan Position 1 Move the cursor to lt Set Scan Position gt and enter below interface SET FFRAME SCAN LEFT LIMIT POSITION IRIS OPEN TO CONTINUE 2 Move the cursor to choose the extreme position of preset by using Left Right keys or joystick of your controller then press Iris Open to enter below interface 15 SETFFRAME SCAN RIGHT LIMIT POSITION IRIS OPEN TO CONTINUE 2 Clear Frame Scan CLEAR FFRAME SCAN IRIS OPEN TO CONTINUE Move the cursor to Clear Frame Scan to enter the press Iris Open to delete the extreme positions 4 2 4 Patterns PATTERNS PATTERN NUMBER PROGRAM PATTERN CLEAR CURRENT PATTERN CLEAR ALL PATTERN EXIT BACK 4 Patterns are supported please refer to below details lt PATTERN NUMBER gt Set Pattern number 1 4 lt PROGRAM PATTERN gt Pattern scan program lt CLEAR CURRENT PATTERN gt Deletes data in current pattern 1 Pattern Number 1 Move the cursor to PATTERN NUMBER by using direction keys and select
14. op during each 90 turning e Auto scan this enables to move the camera to execute the certain scan when no operation for along time e Reserved Presets for special purpose besides regular 256 presets direct calling of reserved presets enable to set up many of camera functions with without using OSD menu PTZ Pan Tilt Zoom Control e RS485 Communication e Pelco D Pelco P special protocols available OSD On screen Display Menu e OSD menu is provided to display the status of camera and to configure the functions interactively e 2 Language are supported e Each display item can be turned ON or OFF independently 1 2 Specifications Video Signal System NTSC PAL CCD 1 4 Interline Transfer CCD Max Pixels 811 H x 508 V 795 H x 596 V Horizontal Resolution 500TV Line Color 570 TV Line B W S N Ratio 50dB AGC off Zoom X10 Optical Zoom X10 Digital Zoom Focal Length F1 8 f 3 8 38mm anne Min illumination 0 7Lux Color 0 02Lux B W F1 8 50 IRE Day amp Night Auto Day Night function ICR Focus Auto Manual SemiAuto Iris Auto Manual Shutter Speed 1 50 1 120000 sec AGC General High Off White Balance ATW Indoor Outdoor AWC Manual Red Blue gain adjustable BLC Low Middle High Off DNR Low Middle High Off Ranga Pan 0 360 Endless Tilt O 180 Preset 360 sec Paniti Pan Tilt Speed Man
15. pattern number then press Iris OPEN to confirm 2 Program Pattern 1 Move the cursorto Program Pattern by using direction keys or joystick of your controller and press IRIS OPEN to enter below interface PROGRAM PATTERN USE THE JOYSTICK OR KEYBOARD TO MOVE THE CAMERA TO THE STARTING POSITION IRIS OPEN TO CONTINUE 2 Using keyboard or joystick of your controller to locate the start position then press Iris Oper to enter PATTERNS STORAGE USED 3 Using keyboard or joystick of controller to edit pattern route and action Max 100 actions then press Iris Open to save 4 2 5 Camera setup We are using Samsung SDM 100P camera to explain below operation 1 Main Menu Camera label Off White Balance Auto BLC Off Auto Detection Off Focus Exposure Additional Menu Back Exit Notice Up Down keys for option Left Right keys for details Iris Open for sub menu 1 Camera Label setup press Iris Open to enter sub menu and edit camera lable Camera Label ABCDEFGHIJKLMNO PQRSTUVWXYZabcd efghljkIlmnopqrs tu v wx y 201234567 89 lt gt lt gt Clean Position Exit Using cursor to select the letter then press Iris Open key to save the setup 2 White Balance setup WB Mode Auto Trace Manual Auto 2 1 Auto Trace Indoor Outdoor The camera can automatically adjust ambient light
16. rsor to sub menu press Iris open to enter into menu e Using UP DOWN keys or joystick to move cursor to the function and press Iris open to choose the function e Using UP DOWN keys or joystick to set up and press Iris open to save e Move the cursor to BACK and press Iris open to back to main menu Note There might display different information due to different camera 4 2 Main menu MAINMENU SYSTEM INFORMATION ADDR SETTING MOTION PATTERNS CAMERA CRUISE SETTING DISPLAY SETUP ON RESTORE FACTORY DEFAULT REBOOT SYSTEM EXIT lt SYSTEM INFORMATION gt Shows system information lt ADDR SETTING gt Select and setup Soft Hard address lt MOTION gt Setup for motion related settings lt PATTERNS gt Setup for Patterns lt CAMERA gt Configure Camera related functions and data lt CRUISE SETTING gt Setup presets scan lt DISPLAY SETUP gt Enable Disable of OSD display on main screen lt RESTORE FACTORY DEFAULT gt Restore factory settings lt REBOOT SYSTEM gt Rebootthe system 4 2 1 System Information SYSTEM INFORMATION COM 2400 N 8 1 ADDRESS 1 PROTOCOL PELCO P PRESETS 256 SOFTWARE VERSION V5 2 BACK EXIT lt COM gt Shows current Baud rate lt ADDRESS gt Shows current Camera ID for PTZ control 0 255 lt PROTOCOL gt Shows current protocol for PTZ control lt PRESETS gt Shows the preset numbers lt SOFTWARE
17. t of Camera ID is 1 e D number of camera is set using binary number The number from 1 8 present 1 2 4 8 16 32 64 128 For example switch 1 3 5 7 to ON position the corresponding ID should be 1 4 16 64 85 The example is shown below Code Switch Code Switch ID No ID No 12345678 12345678 0 00000000 10 01010000 1 10000000 20 00101000 2 01000000 30 01111000 3 11000000 50 01001100 4 00100000 100 00100110 5 10100000 101 10100110 6 01100000 150 01101001 7 11100000 200 00010011 8 00010000 255 11111111 2 2 2 Communication Protocol and Baud rate Setup e a e Selectthe appropriate protocol with DIP switch combination Switch State Protocol Pin No 1 2 3 4 OFF OFF PELCO P Proto i ON OFF PELCO D OFF ON Auto ON ON Reserved OFF OFF 9600 diia ON OFF 2400 OFF ON 4800 ON ON 9600 3 Operation 3 1 Check points before operation e Before power is connected please check the cables carefully e The camera ID of the controller must be identical to that of the camera to be controlled The camera ID can be checked in the System Information of OSD Menu e f you controller supports multi protocols the protocol must be changed to match to that of the camera elf you change camera protocol by changing DIP switch the change will be effective after you reboot the camera
18. ual Pan 300 sec Tilt 180 a to zoom Auto Pan 1 180 sec adjustable Preset 256 Preset Label Camera Image Setting Cruise Auto Pan Pattern Scan Other Functions Auto Flip Auto Parking Power up Action etc Communication RS 485 General Protocol Pelco D Pelco P Special protocols available Baud rate 2400 4800 9600 Language English 2 Installation 2 1 Installation and Connection 2 1 1 Wall Mount 1 Connect Camera Plug the terminals into the bottom of the main unit then fix the main unit with screws supplier power A BNC Video 2 Bracket Installation Use the screws provided to secure the wall mount to the wall 2 1 2 Ceiling Mount 1 Fix the main unit on the bracket After wiring cables to terminals plug the terminals into the bottom of main unit Then fix the main unit with screws provided o TN The cable cross through bottle position and be out of breach of bottle position 2 Install ceiling mount bracket on the ceiling using screws provided 2 1 3 Cabling Connector Interface DC 12V 485A Red 485B Black BNC Video 2 2 DIP Switch Setup Before you install the camera you should set the DIP switches to configure the camera ID Baud rate and communication protocol Default ID 1 Baud rate 2400 Protocol Pelco D 2 2 1 Camera ID Setup gt MU eThe range of ID is 0 255 Factory defaul
Download Pdf Manuals
Related Search