Home

POC-200 Series User's Manual Rev A1.1

1. 5 Carefully push back the case and fix the chassis assembly using four M4 F head screws De o Copyright 2014 Neousys Technology Inc All Right Reserved Page 42 of 78 POC 200 Series User s Manual 3 3 2 Install a 2 5 HDD SSD on POC 212 222 1 Loose the hand screw and pull out the HDD bracket 2 Remove the protect firm from the thermal pad on the HDD bracket 3 Get four M3 F head screws from the accessory box Attach the HDD SSD to the bracket using four M3 F head screws Another two screws are on the opposite side 4 Gently slide the HDD assembly into the SATA connector till they re firmly connected roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 43 of 78 POC 200 Series User s Manual 5 Fasten the hand screw of POC 212 POC 222 3 4 Install a Mini PCle Module POG 200 series provides one mini PCle connector with SIM socket to accommodate versatile mini PCle modules e g 3G 4G WIFI GPS for further function expansion In this section we ll demonstrate how to install a mini PCle WIFI module and attach an antenna to your POC 200 series Please note that the mini PCle WIFI module cable and antenna are not part of POC 200 series and may be different according to your system configuration 3 4 1 Install a Mini PCle Module on POC 200 POC 210 1 Follow the steps in section 3 1 1 to dissemble your POC 200 210 You can see the mini PCle connector exposed
2. SATA HDD 1x internal SATA port for 2 5 HDD SSD Power Supply DC Input Built in 8 35 VDC DC input Input Connector 2 pin pluggable terminal block for DC input Power Consumption Typical 7 27W 0 30AQ24V Full loading 9 60W 0 40A 24V Mechanical Dimension 149mm W x 105 mm H x 54 mm D Weight 1 1 kg with one 2 5 SATA HDD Mounting Wall mount Standard DIN rail mount Optional Environmental Operating 30 C 70 C with SSD 100 CPU loading Temperature 10 C 60 C with HDD 100 CPU loading Storage 40 C 85 C Temperature Humidity 10 90 non condensing es Copyright 2014 Neousys Technology Inc All Right Reserved Page 12 of 78 POC 200 Series User s Manual Vibration Operating 5 Grms 5 500 Hz 3 Axes w SSD wo add on card according to en Operating 50 Grms Half sine 11 ms Duration w SSD w o add on card according to IEC60068 2 27 EMC CE FCC Class A according to EN 55022 amp EN 55024 Full loading power consumption is measured with 2GB DDR3 memory and one 2 5 SATA HDD installed under the following conditions 100 loading for Atom E3845 CPU 10026 loading for 3D graphics 10026 loading for GbE port The 100 CPU loading is applied using Passmark BurninTest v7 0 For detail testing criteria please contact Neousys Technology For sub zero operating temperature wide temperature DDR
3. 2 Tilt the mini PCle WIFI module and insert it to the mini PCle port And fix the WIFI module with two M2 5 P head screws 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 44 of 78 POC 200 Series User s Manual 3 Attach the IPEX to SMA cable to the WIFI module and fix the SMA connector on the IPEX to SMA cable to back panel 4 Carefully push back the case and fix the chassis HDD assembly using four M4 F head screws 5 Attach the WIFI antenna to the SMA connector I roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 45 of 78 POC 200 Series User s Manual 3 4 2 Install a Mini PCle Module on POC 212 222 1 Follow the steps in section 3 1 2 to dissemble your POC 212 222 You can see the mini PCle connector exposed 2 Tilt the mini PCle WIFI module and insert it to the mini PCle port And fix the WIFI module with two M2 5 P head screws 3 Attach the IPEX connector of the IPEX to SMA cable to the WIFI module 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 46 of 78 POC 200 Series User s Manual 4 Carefully push back the case and fix the chassis with heat sink using four hex bolts 5 Fix the SMA connector of the IPEX to SMA cable to back panel 6 Attach the WIFI antenna to the SMA connector 2 roe Copyright 2014 Neousys Technology Inc
4. 44W 0 56A 24V Mechanical Dimension 149mm W x 105 mm H x 58 mm D Weight 1 1 kg with one 2 5 SATA HDD Mounting Wall mount Standard DIN rail mount Optional Environmental Operating 30 C 70 C with SSD 100 CPU loading Temperature 10 C 60 C with HDD 100 CPU loading Storage Temperature RR oer Humidity 10 90 non condensing Vibration Operating 5 Grms 5 500 Hz 3 Axes w SSD wo add on card according to sia Operating 50 Grms Half sine 11 ms Duration w SSD w o add on card according to IEC60068 2 27 EMC CE FCC Class A according to EN 55022 amp EN 55024 Full loading power consumption is measured with 2GB DDR3 memory and one 2 5 SATA HDD installed under the following conditions 10026 loading for Atom E3845 CPU 100 loading for 3D graphics 10026 loading for GbE port The 100 CPU loading is applied using Passmark BurninTest v7 0 For detail testing criteria please contact Neousys Technology For sub zero operating temperature wide temperature DDR3 L and wide temperature HDD SSD are required 1 2 3 Specification of POC 212 System Core Processor Intel Atom E3845 1 91 GHz quad core processor Graphics Integrated Intel HD Graphics Memory 1x SODIMM socket for DDR3L 1333 up to 8GB Panel I O Interface Ethernet 2x Gigabit Ethernet ports by Intel 1210 GbE controller PoE N A
5. 9 DI 2 Digital input channel 2 10 DO GND Digital output GND 11 DI 3 Digital input channel 3 12 DO 2 O Digital output channel 2 13 DI GND Digital input GND 14 DO 3 O Digital output channel 3 15 DI GND Digital input signal 16 DO GND Digital output GND 2 runs Copyright O 2014 Neousys Technology Inc All Right Reserved Page 75 of 78 POC 200 Series User s Manual Pin Definition for 5V TTL GPIO POC 210 212 222 2 16 1 15 Pin Definition Pin Definition I O Description 1 N C No connection 2 N C No connection 3 DI 0 Digital input channel 0 4 N C No connection 5 DI 1 Digital input channel 1 6 DO 0 O Digital output channel 0 7 N C No connection 8 DO 1 O Digital output channel 1 9 DI 2 Digital input channel 2 10 D GND GND Digital GND 11 DI 3 Digital input channel 3 12 DO 2 O Digital output channel 2 13 N C No connection 14 DO_3 O Digital output channel 3 15 N C No connection 16 D_GND GND Digital GND DIO Function Reference InitDIO Description Initialize the DIO function You should always invoke InitDIO before write read any DIO port channel Parameter 2 runs Copyright 2014 Neousys Technology Inc All Right Reserved Page 76 of 78 POC 200 Series User s Manual None Return Value Returns TRUE if initialization successes FALSE if initialization failed Usage BOOL bRet InitWDT DiReadLine De
6. All Right Reserved Page 47 of 78 POC 200 Series User s Manual 3 5 Mount your POC 200 Series POG 200 series provides versatile ways of mounting The chassis itself is designed to be used as a mounting bracket which can mounted inside out or outside in Neousys also offers the option of DIN rail mounting clip so you can mount POC 200 on a DIN rail To mount your POC 200 please refer to the information listed below 3 5 1 Suspend your POC 200 on the Wall You can take advantage of two keyhole shaped holes on the bottom side of the chassis to suspend your POC 200 on the wall With two pre installed screws 88 mm pitch on the wall you can easily suspend or displace the POC 200 This way of mounting is only suitable for a steady environment without shock and vibration 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 48 of 78 POC 200 Series User s Manual 3 5 2 Mount your POC 200 Outside in on a Surface There are two nuts with M4x0 7 thread on the bottom side of POC 200 so you can fix it outside in using two M4 screws This is convenient if you want to deploy POC 200 ina restricted space where inside out mounting is not applicable M4 Screws 2X 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 49 of 78 POC 200
7. Inc All Right Reserved Page 31 of 78 POC 200 Series User s Manual 2 5 POC 200 210 Mechanical Dimension 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 32 of 78 2 5 1 Top View 122 60 POC 200 Series User s Manual 2 5 2 Front View 104 70 2 5 3 Side View VA NEOUS S tar U 148 70 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 33 of 78 POC 200 Series User s Manual 2 5 4 Bottom View M4 Thread RUI roves Copyright 2014 Neousys Technology Inc All Right Reserved Page 34 of 78 POC 200 Series User s Manual 2 6 POC 212 222 Mechanical Dimension 2 6 1 Top View roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 35 of 78 122 00 SO POC 200 Series User s Manual 2 6 2 Front View il 2 6 3 Side View NMEOUSTS 148 70 2 roe Copyright 2014 Neousys Technology I
8. Jumper Setting AT ODO ATX OOO Push the non latched switch will turn on the system the PWR LED indicator on the front panel is on at the same time Push the non latched switch when system is on will turn off the system If your operating system supports ATX power mode i e Microsoft Windows or Linux push the power button causes a pre defined system behavior such as shutdown or hibernation 3 7 4 To Power on POC 200 Using Wake on LAN Function Wake on LAN WOL is a mechanism to wake up a computer system from a S8 standby S4 Hibernate or S5 system off with standby power state via issuing Subnet Directed Broadcasts SDB or a magic packet POC 200 series implements the Wake on LAN function for its first GbE port DIO GPIO To enable WOL function and power on you POC 200 please follow the steps listed below When POC 200 boots up press F2 to enter BIOS setup utility Enter the Power menu And configure the Wake On LAN option as Enabled This setting enables the Wake on LAN function for POC 200 series Please refer to section 4 1 5 for the instruction of configuring this BIOS option In Windows 7 system identify the Local Area Connection of corresponding Intel 1210 Gigabit Controller and click the Configure button 2 rme pra Copyright 2014 Neousys Technology Inc All Right Reserved Page 56 of 78 4 f g Local Area Connection 5 Properties Connec using Da Intel R 1210 Gigabit
9. Series User s Manual 3 5 3 Mount your POC 212 222 Inside out on a Surface For POC 212 222 you can take advantage of four mounting holes on the bottom side to fix your POC 212 222 inside out on a surface To do this you need to remove its chassis from the PCBA heat sink assembly first Please follow the steps listed in section 3 1 2 and then you can use the chassis as the mounting bracket Once you fix the chassis inside out on a surface you can slide the assembly of PCBA heat sink assembly back into the chassis Fix it with hex bolts and the POC 212 222 is firmly mounted on a surface 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 50 of 78 POC 200 Series User s Manual 3 5 4 Mount your POC 200 on the DIN Rail Neousys also provides the option of the DIN rail mounting clip With the mounting clip you can fix POC 200 on a DIN rail This option can be useful if you want to deploy POC 200 inside an equipment cabinet where DIN rail is available M4 Screws 2X roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 51 of 78 POC 200 Series User s Manual 3 6 Connect DC power to you POC 200 POC 200 series uses a 2 pin pluggable terminal block to accept 8 35V DC power input It provides the way for directly wiring the DC power To connect DC power via the 2 pin pluggable terminal block please follow the step
10. logic units inside the CPU to save the energy consumed The trade off however is a longer latency for CPU to wake up and be 100 operational Depending on your application you can configure these options to have higher performance disable C States or lower power consumption enable C States and set Max C States to C6 C7 To set C States and Enhanced C States 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Power gt Advanced CPU Control 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 61 of 78 POC 200 Series User s Manual 3 Enable disable the C States option according to your application 4 Configure the Max C States option according to your application C States lt Enab led gt Enabled 4 1 5 Wake on LAN Option Wake on LAN WOL is a mechanism which allows you to turn on your POC 200 via Ethernet connection To utilize Wake on LAN function you have to enable this option first in BIOS settings Please refer to section 3 7 4 for instructions of using WOL function To enable disable Wake on LAN option 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Power 3 Enable disable the Wake on LAN option according to your application Wake on LAN lt Disabled gt Disabled on Copyright 2014 Neousys Technology Inc All Right Reserved Page 62 of 78 POC 200 Series User s Manual 4 1 6 Power On after Powe
11. rd E1600118 Ea 53 POC 200 series provides an on board Mini PCI Express socket with SIM card support There are plenty of off the shelf mini PCle modules with versatile capabilities By installing a mini PCle module your system can have expanded features such as WIFI 3G GPS RAID and etc In addition the SIM card support makes it possible to connect your system to Internet in wide territory through telecom operator s GPRS 3G network 2 4 3 DDR3L SODIMM Socket si P0C22000 5 AM E 16500118 8 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 30 of 78 POC 200 Series User s Manual POC 200 series provides one 204 pin SODIMM socket for memory installation It supports a maximal 8GB capacity by installing one low voltage 1 35V DDR3L 1333 SODIMM modules For information of installing DDR3L memory modules please refer to section 3 2 for detail Note Please make sure youre installing a 1 35V DDR3L SODIMM module to POC 200 Installing a 1 5V DDR3 SODIMM will cause system failed to boot 2 4 4 SATA Connector POC 200 series provides one SATA port to accommodate a 2 5 SATA hard drive inside it The SATA port is located on the daughter board via a 22 pin SATA connector With the HDD bracket shipped with POC 200 series you can directly mount a 2 5 HDD or SSD to this port For information of installing a HDD SSD to SATA port please refer to section 3 3 for detail o Copyright 2014 Neousys Technology
12. you can either issue a shutdown command in OS or just simply press the power button In case of system halts you can press and hold the power button for 5 seconds to compulsorily shut down the system Please note that a 5 seconds interval is kept by the system between two on off operations i e once turning off the system you shall wait for 5 seconds to initiate another power on operation roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 15 of 78 POC 200 Series User s Manual 2 2 2 Reset Button DIO GPIO The reset button is used to manually reset the system in case of any abnormal condition To avoid unexpected operation the reset button is hidden behind the front panel You need to use a pin like object to push the reset button 2 2 3 LED Indicators DIO GPIO There are three LED indicators on the front panel PWR WDT and HDD The descriptions of these three LED are listed in the following table Indicator Color Description PWR Green Power indictor lighted up when system is on off when system is off WDT Yellow Watchdog timer indicator flashing when watchdog timer is started HDD Red Hard drive indicator flashing when SATA hard drive is active Page 16 of 78 Copyright O 2014 Neousys Technology Inc All Right Reserved SSS POC 200 Series User s Manual 2 2 4 USB 3 0 Connectors DIO GPIO There are totally three USB 3 0 ports and one USB 2 0 po
13. 1x DVI I connector for both analog RGB and DVI HDMI outputs supporting up to Video Port 2560 x 1600 resolution 1x software programmable RS 232 422 485 COM1 Serial Port 1x RS 232 COM2 eos Copyright 2014 Neousys Technology Inc All Right Reserved Page 10 of 78 POC 200 Series User s Manual 1x USB 3 0 port via native USB3 controller USB 2x USB 3 0 ports via Renasas uPD720202 USB3 host controller 1x USB 2 0 port Audio 1x Speaker out DIO 4 CH 5V TTL DI 4 CH 5V TTL DO Internal I O Interface Mini PCle 1x mini PCI Express slot with USIM socket Storage Interface SATA HDD 1x internal SATA port for 2 5 HDD SSD Power Supply DC Input Built in 8 35 VDC DC input Input Connector 2 pin pluggable terminal block for DC input Typical 7 68W 0 32A 24V Power Consumption Full loading 13 44W 0 56A 24V Mechanical Dimension 149mm W x 105 mm H x 54 mm D Weight 1 1 kg with one 2 5 SATA HDD Mounting Wall mount Standard DIN rail mount Optional Environmental Operating 30 C 70 C with SSD 100 CPU loading Temperature 10 C gt 60 C with HDD 100 CPU loading Storage Temperature E Humidity 10 90 non condensing Vibration Operating 5 Grms 5 500 Hz 3 Axes w SSD wo add on card according to Bite Operating 50 Grms Half sine 11 ms Duration w SSD w o add on card according to IEC60068 2 27 EM
14. 3 L and wide temperature HDD SSD are required reou Copyright 2014 Neousys Technology Inc All Right Reserved Page 13 of 78 POC 200 Series User s Manual Chapter 2 Getting Started 2 1 Unpacking your POC 200 When you receive the package of POC 200 series please check immediately if the package contains all the items listed in the following table If any item is missing or damaged please contact your local dealer or Neousys Technology Inc for further assistance Item Description Qty 1 POC 200 210 212 222 ultra compact fanless controller 1 According to the configuration you order your POC 200 may contain DDR3L module or SATA HDD Please verify these items if necessary Specialized DVI to VGA adapter for POC 200 2 pin pluggable terminal block Neousys Drivers amp Utilities DVD o1 amp W Po i k mk Screw package De roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 14 of 78 POC 200 Series User s Manual 2 2 Front Panel I O Functions On POC 200 series we design general purpose I O functions on the front panel so you can easily access them In this section we ll illustrate each I O function on the front panel 2 2 1 Power Button DIO GPIO The power button is a non latched switch for ATX mode on off operation To turn on the POC 200 press the power button and the PWR LED on the center top side is lighted up To turn off the POC 200
15. 4 DTR 422 RXD DTR 5 GND GND GND GND 6 DSR DSR 7 RTS RTS 8 CTS 422 TXD 485 TXD RXD CTS 9 RI RI 2 3 4 COM Ports on POC 200 210 POC 200 and POC 210 provide four COM ports via four 9 pin D Sub male connectors on the back panel for communicating with external devices They are implemented using industrial grade ITE8783 Super IO chip 40 to 85 C and provide up to 115200 bps baud rate COM1 COM3 are software selectable RS 232 422 485 ports and COM2 COM4 support RS 232 only The operation mode of COM1 COM8 can be set in BIOS setup utility refer to section 4 1 1 4 1 2 for detail The following table describes the pin definition of COM ports 2 SSS Copyright 2014 Neousys Technology Inc All Right Reserved Page 26 of 78 0000 SIRIO POC 200 Series User s Manual COM1 COM3 COM2 COM4 Pint RS 232Mode RS 422 Mode 19495 Mode RS 232 Mode Two wire 485 1 DCD DCD 2 RX 422 TXD 485 TXD RXD RX 3 TX 422 RXD TX 4 DTR 422 RXD DTR 5 GND GND GND GND 6 DSR DSR 7 RTS RTS 8 CTS 422 TXD 485 TXD RXD CTS 9 RI RI 2 3 5 2 Pin Terminal Block for DC Input POC 200 series features a pluggable terminal block for direct DC wiring The 2 pin pluggable terminal block on the back panel is fit for field usage where DC power is usually provided It accepts a wide range of DC power input from 8 to 35V And the screw clamping connection of terminal block gives
16. 6 DIO Function Reference Lasses 76 IDO 76 I 13 110 Bj elle es 77 DIRT HL vrede oe ee eee 77 DOWrieLino Rea 77 DOWER ON zizi re ene ene iaia allieta 78 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 5 of 78 POC 200 Series User s Manual Declaimer This manual is intended to be used as a practical and informative guide only and is subject to change without prior notice It does not represent commitment from Neousys Technology Inc Neousys shall not be liable for direct indirect special incidental or consequential damages arising out of the use of the product or documentation nor for any infringements upon the rights of third parties which may result from such use Declaration of Conformity FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE The product s described in this manual complie
17. B OC 78 DO 04 0A 0B 0C 78 DO 04 OA OB OC 78 DO 04 0A 0B 0C 78 DO 04 OA OB OC 78 DO 04 0A 0B 0C 78 DO 04 0A OB OC 78 DO 04 0A 0B 0C 78 DO 04 OA OB OC 78 DO 04 0A 0B 0C MISC CRC There are some free tools available on Internet that can be used to send a magic packet Please refer to the following link to understand more about Magic Packet http en wikipedia org wiki Wake on LAN Wake on Magic Packet from power off state When checking this option POC 200 can wake from S5 system off with standby power state when receiving a magic packet Copyright 2014 Neousys Technology Inc All Right Reserved Page 58 of 78 POC 200 Series User s Manual Chapter 4 BIOS and Driver 4 1 BIOS Settings POG 200 series is shipped with factory default BIOS settings cautiously programmed for best performance and compatibility In this section we ll illustrate some of BIOS settings you may need to modify Please always make sure you understand the effect of change before you proceed with any modification To Enter BIOS setup When POC 200 is booting up press F2 to enter BIOS setup utility Use following keys to edit change BIOS options Keys Function F1 Help He Select Item F5 F6 Change Values F9 Load Setup Defaults Esc Exit Enter Select gt SubMenu F10 Save and Exit 4 1 1 COM1 Operation Mode COM1 of POC 200 series supports RS 232 full duplex RS 422 full duplex and RS 485 half duplex mode
18. C CE FCC Class A according to EN 55022 amp EN 55024 Full loading power consumption is measured with 2GB DDR3 memory and one 2 5 SATA HDD installed under the following conditions 100 loading for Atom E3845 CPU 100 loading for 3D graphics 100 loading for GbE port The 100 CPU loading is applied using Passmark BurninTest v7 0 For detail testing criteria please contact Neousys Technology For sub zero operating temperature wide temperature DDR3 L and wide temperature HDD SSD are required roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 11 of 78 POC 200 Series User s Manual 1 2 4 Specification of POC 222 System Core Processor Intel Atom E3825 1 33 GHz dual core processor Graphics Integrated Intel HD Graphics Memory 1x SODIMM socket for DDR3L 1067 up to 4GB Panel I O Interface Ethernet 2x Gigabit Ethernet ports by Intel 1210 GbE controller PoE N A 1x DVI I connector for both analog RGB and DVI HDMI outputs supporting up to Video Port 2560 x 1600 resolution 1x software programmable RS 232 422 485 COM1 Serial Port 1x RS 232 COM2 1x USB 3 0 port via native USB3 controller USB 2x USB 3 0 ports via Renasas uPD720202 USB3 host controller 1x USB 2 0 port Audio 1x Speaker out DIO 4 CH 5V TTL DI 4 CH 5V TTL DO Internal I O Interface Mini PCle 1x mini PCI Express slot with USIM socket Storage Interface
19. Network Connection 45 Giant for Microsoft Netwodcs A JE Fie and Printer Sharing for Microsoft Networks kd intemet Protocol Version 6 TCP Pv be htenet Protocol Version TCP APv A 4 Link Layer Topology Discovery Mapper 1 0 Driver 4 4 Link Layer Topology Discovery Responder install Uninstall Properties Allows your computerto access resources on a Microsoft network intel Power Saver and Wake on LAN Options 7 Wake on Magic Packet Id LAKE en Eanan Mate v Wake on Magie Packet from power off state Enables a management siation 19 bring the computer out o standby or hibernation wien a Magic Packet is seni directly lu the adapler Wake on Magic Packet POC 200 Series User s Manual POC 200 can wake from S3 or S4 state when receiving a magic packet The magic packet is a broadcast frame containing anywhere within its payload 6 bytes of all 255 FF FF FF FF FF FF in hexadecimal followed by sixteen repetitions of the target computer s 48 bit MAC address 2 meaa Copyright 2014 Neousys Technology Inc All Right Reserved Page 57 of 78 2 SSS POC 200 Series User s Manual For example NIC s 48 bit MAC Address is 78h DOh 04h OAh OBh OCh DESTINATION SOURCE MISC FF FF FF FF FF FF 78 DO 04 OA OB OC 78 DO 04 0A 0B 0C 78 DO 04 OA OB OC 78 DO 04 0A 0B 0C 78 DO 04 OA OB OC 78 DO 04 0A 0B 0C 78 DO 04 OA O
20. POC 200 Series User s Manual Neousys Technology Inc POC 200 Series Ultra compact Atom TM Bay Trail I Fanless Embedded Controller with PoE and USB 3 0 User s Manual Rev A1 1 Published Sep 24 2014 Jr runs Copyright O 2014 Neousys Technology Inc All Right Reserved Page 1 of 78 POC 200 Series User s Manual Date Description Version 2014 09 24 Modify 5V TTL GPIO Pin Define Page 21 75 A1 1 2 reoLer Copyright 2014 Neousys Technology Inc All Right Reserved Page 2 of 78 POC 200 Series User s Manual Contents DEecamMe ricci 6 Declaration of Conformity 2 ivei 6 Poli 6 Lecca 6 COpyrighrand Trademarks arsen 6 Chapter 1 Introduction iii ere et een ere orale aiar 7 EEE sana E koeta kaa koe aaa ae a e aa be a a ae aane a a AE a ne a AE wg be a aa KAE E 7 12 Product SPE eee 8 1 2 1 Specification OF POC 200 lella 8 1 2 2 Specification of POG 210 1ummssmimsmmmansinemmdesinejvinjvsi ne 9 1 2 3 Specification of POG 212 usmmseemiemsssesmenmiannasssisvnmisis dsdevvv 10 1 2 4 Specification of POC 222 aaa eaaa anana eaaa anana eaaa anana aee e anna 12 Chapter 2 GENG Sbeitla 14 2 1 Unpacking your POC 200 aaa aaaaaaae eaaa aaa aana anana renerne 14 2 2 Front Panel I O FUNCHIONS neeaaea eenen eenen nenene ennen rennene nnnnnennnn nennen 15 22 OW GN Bultaco 15 222 Reset BUON aaa 16 2 2 3 LED IndicatorS said 16 224 USB 30000600 iii iii iii AEREA A 17 2 2 5 Spe
21. SB3 driver for Bay Trail SoC Please refer to section 4 3 for information of driver installation 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 24 of 78 POC 200 Series User s Manual 2 3 2 USB2 0 Connectors In addition to three USB 3 0 ports POC 200 series provides another USB 2 0 port on its back panel By BIOS default these USB 2 0 ports are operated in EHCI Enhanced Host Control Interface mode and are compatible with USB 2 0 USB 1 1 and USB 1 0 devices Legacy USB support is provided so you can use USB keyboard mouse in DOS environment 2 3 3 COM Ports on POC 212 222 4446060644 USB2 0 fr POC 212 and POC 222 provide two COM ports via two 9 pin D Sub male connectors on the back panel for communicating with external devices They are implemented using industrial grade ITE8783 Super IO chip 40 to 85 C and provide up to 115200 bps baud rate COM1 is a software selectable RS 232 422 485 port and COM2 supports RS 232 only The operation mode of COM1 can be set in BIOS setup utility refer to section 4 1 1 for detail The following table describes the pin definition of COM ports 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 25 of 78 0000 SIRIO POC 200 Series User s Manual COM1 COM2 Pint RS 232Mode RS 422 Mode 19495 Mode RS 232 Mode Two wire 485 1 DCD DCD 2 RX 422 TXD 485 TXD RXD RX 3 TX 422 RXD TX
22. You can set the COM1 operating mode via BIOS settings Another option in BIOS called Slew Rate defines how sharp the rising falling edge is for the output signal of COM1 For long distance RS 422 485 transmission you may set the Slew Rate option as High to improve signal quality For RS 422 485 communication the RS 422 485 Termination option determines whether to enable disable internal termination of RS 422 485 transceiver according to your wiring configuration e g with or without external termination To set COM1 operating mode 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Advanced gt Peripheral Configuration 3 Set the Set COMI as option to a proper mode for COM1 of your POC 200 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 59 of 78 POC 200 Series User s Manual Set COMI as lt RS 232 gt 4 1 2 COM3 Operation Mode POC 200 210 Only POC 200 210 features four COM ports COM3 also supports RS 232 full duplex RS 422 full duplex and RS 485 half duplex mode You can set the COM3 operating mode via BIOS settings Another option in BIOS called Slew Rate defines how sharp the rising falling edge is for the output signal of COM3 For long distance RS 422 485 transmission you may set the Slew Rate option as High to improve signal quality For RS 422 485 communication the RS 422 485 Termination option determines whether to en
23. _ALC262 Win7_8 ALL Setup exe 4 LAN driver x Driver_Pool GbE_1210 Win7_8_32 APPS PROSETDX Win32 DxSetup exe USB 3 0 driver x USB3_VIv Win7_ALL Setup exe 6 Renasas USB3 driver x Driver_Pool USB3_Renasas Win_ALL Setup exe LI Windows 7 64 bit The recommended driver installation sequence is 1 Chipset driver x Driver_Pool Chipset_VIv Win7_8_ALL SetupChipset exe 2 Graphics driver x Driver_Pool Graphics_Vlv_EMGD Win7_64 Setup exe 3 Audio driver x Driver_Pool Audio ALC262 Win7_8_ALL Setup exe 4 LAN driver x Driver_Pool GbE_1210 Win7_8 64 APPS PROSETDX Winx64 DxSetup exe USB 3 0 driver x Driver_Pool USB3_VIv Win7_ALL Setup exe 6 Renasas USB3 driver x Driver_Pool USB3_Renasas Win_ALL Setup exe on Windows 8 8 1 32 bit The recommended driver installation sequence is 1 Chipset driver x Driver_Pool Chipset_Vlv Win7_8 ALL SetupChipset exe 2 Graphics driver x Driver_Pool Graphics_3rd_i7_Vlv Win7_8_ 32 Setup exe 3 Audio driver x Driver_Pool Audio ALC262 Win7_8_ALL Setup exe 4 LAN driver x Driver_Pool GbE_1210 Win7_8_32 APPS PROSETDX Win32 DxSetup exe 5 TXE driver x Driver_Pool TXE_Vlv Win8_ALL SetupTXE exe Windows 8 8 1 64 bit The recommended driver installation sequence is 1 Chipset driver x Driver_Pool Chipset_Vlv Win7_8 ALL SetupChipset exe 2 Graphics driver x Driver_Pool Graphics_3rd_i7_Vlv Win7_8 64 Setup exe 3 Audio driver x Driver_Pool Audio ALC262 Win7_8_ALL Setup e
24. a very reliable way for wiring the DC power The following table describes the pin definition of the pluggable terminal block For detail information of connecting DC power please refer to section 3 6 2 SSS Copyright 2014 Neousys Technology Inc All Right Reserved Page 27 of 78 POC 200 Series User s Manual Pin Description V Positive polarity of DC power input 8 35V V Negative polarity of DC power input usually power ground Caution Please make sure the voltage and polarity of DC power is correct before you connect it to POC 200 Supplying a voltage over 35V will damage the system reou Copyright 2014 Neousys Technology Inc All Right Reserved Page 28 of 78 POC 200 Series User s Manual 2 4 Internal I O Functions 2 4 1 Remote On Off Control The remote on off control function allows users to turn on or turn off the system remotely by connecting an external switch This function is provided via a 1x3 pins 2 0mm pitch pin header Both AT mode and ATX mode on off control are supported For detail information of using remote on off control function please refer to section 3 7 2 3 7 3 Switch Connection for AT ATX Mode Remote On Off Control Mode Jumper Setting AT ATX roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 29 of 78 POC 200 Series User s Manual 2 4 2 Mini PCI Express Connector and SIM Socket 7 P0c22000
25. able disable internal termination of RS 422 485 transceiver according to your wiring configuration e g with or without external termination To set COM3 operating mode 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Advanced gt Peripheral Configuration 3 Set the Set COM3 as option to a proper mode for COM3 of your POC 200 Set COM3 as lt R 232 gt roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 60 of 78 POC 200 Series User s Manual 4 1 3 Chipset SATA Mode The SATA controller of POC 200 series supports two modes of operations IDE and AHCI mode IDE mode configures SATA controller to access SATA interface in legacy IDE mode and is compatible with most storage devices AHCI mode which exposes SATA s advanced capabilities such as hot swapping and native command queuing can deliver better performance for disk read write As POC 200 series no longer supports Windows XP we highly recommend you to set Chipset SATA Mode to AHCI for better system performance To set Chipset SATA mode 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Advanced gt SATA Configuration 3 Set the Chipset SATA Mode option to a proper mode for your POC 200 Chipset SATA Mode lt AHC I gt 4 1 4 C States and Max C States C States is a power saving technique implemented in modern Intel processors It shuts down the clock signals and power for idle
26. aker out JACK alri 17 2 26 Gigabit EfhemetPFols ssaa 18 2 2 7 IEEE 802 3at PoE PSE POC 200 Only nerne n rr nnnee 19 228 DVELCONNECIO aria 19 2 29 DIO Cane 20 2 2 9 1 Isolated DIO on POL 200 seen 20 2 2 9 2 5V TTL GPIO on POC 210 POC 212 POC 222 rrnnnnnnnnnnrvrrvnnnnnnrnr 22 2 3 Back Panel VO Functions iii 24 2 3 1 USB3 0 Connectors EE 24 2 3 2 USB2 0 Connectors akawakawa ka warara ka wakakakak araga wa kawa kawa kaa kawa kaa dawa kaa kawa kaa 25 2 3 3 COM Ports on POC 212 222 nee eeen e eene eennnnnnnnnennnnnnen en 25 2 3 4 COM Ports on POC 200 210 i 26 2 3 5 2 Pin Terminal Block for DC INput ce eeeeeeeeee tree anana nana aana nane 27 24 Internal 1 0 FUNCIONS 555 ira eenean e eniai 29 2 4 1 Remote On Off Control eaaa eaaa aane nane nan ae eaaa nenen anane eaaa eaaa nenen 29 2 4 2 Mini PCI Express Connector and SIM Socket 30 2 4 3 DDR3L SODIMM Socket ananen anaa aana anana aana a anana aana nane 30 2 4 4 SATA MEN 31 2 5 POC 200 210 Mechanical DIMENSION 32 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 3 of 78 POC 200 Series User s Manual 2 5 1 Top Ne 32 2 52 FOM VEN licia 33 2 SBS ENN eee 33 2 5 4 Bottom VI lia 34 2 6 POC 212 222 Mechanical DIMENSION sasewene raa aaanan anana anana anana anana ena 35 2 61 TOP VIEW ek 35 202 Front VIEW eo 36 2 6 3 Side View saana
27. e DVI HDMI and VGA outputs are directly driven by integrated Intel HD Graphics engine and support up to 2560 x 1600 resolution 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 19 of 78 POC 200 Series User s Manual For VGA monitor Neousys offers a specialized DVI to VGA adapter as an accessory shipped with POC 200 series This adapter supports VGA DDC signals and thus eliminates compatibility issues with VGA monitors Or you can use a DVI I to VGA DVI D Y cable to support two independent display outputs DVI to VGA Adapter DVI I to VGA DVI D Y Cable To have best graphics performance in Windows you need to install corresponding graphics driver Please refer to section 4 3 for information of driver installation 2 2 9 DIO Connector 2 2 9 1 Isolated DIO on POC 200 DIO GPIO POC 200 integrates 2500Vrms isolated DIO function for extending application range This feature provides 4 channels of isolated digital input and 4 channels of isolated digital output via a 16 pin box header connector The following table describes the pin definition of isolated DIO connector roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 20 of 78 POC 200 Series User s Manual 16 1 15 Pin Definition Pin Definition I O Description 1 ISO 5V O Isolate 5V power supply 2 VDD DO voltage source input f
28. e type The default order of boot device type is Hard Disk Drive e USB e CD DVD ROM Driver 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 64 of 78 POC 200 Series User s Manual Floppy Drive e Others You can use F5 F6 or to change the boot order of devices or device types Boot Henu lt By Device gt o Copyright 2014 Neousys Technology Inc All Right Reserved Page 65 of 78 POC 200 Series User s Manual 4 2 Operating System Support POC 200 series supports most operating system developed for Intel x86 architecture The following list contains the operating systems which have been tested in Neousys Technology Inc Microsoft Window 7 32 bit Microsoft Window 7 64 bit Microsoft Window 8 8 1 32 bit Microsoft Window 8 8 1 64 bit Ubuntu 14 04 or later version For Linux system user may need to manually compile and install the driver for Intel 1210 GbE controller if the driver is not embedded in kernel You can visit Intel website for further information Neousys will keep this list updated as we continuously test other operating systems with POC 200 series Please contact us for the latest OS support list roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 66 of 78 POC 200 Series User s Manual 4 3 Driver Installation Neousys Technology Inc provides a very convenient utility in Drivers amp Utilities DVD to allow the One Click driver installatio
29. for GbE port The 100 CPU loading is applied using Passmark BurninTest v7 0 For detail testing criteria please contact Neousys Technology For sub zero operating temperature wide temperature DDR3 L and wide temperature HDD SSD are required 1 2 2 Specification of POC 210 System Core Processor Intel Atom E3845 1 91 GHz quad core processor Graphics Integrated Intel HD Graphics Memory 1x SODIMM socket for DDR3L 1333 up to 8GB Panel I O Interface Ethernet 2x Gigabit Ethernet ports by Intel 1210 GbE controller PoE N A 1x DVI I connector for both analog RGB and DVI HDMI outputs supporting up to Video Port 2560 x 1600 resolution 2x software programmable RS 232 422 485 COM1 amp COM3 Serial Port 2x RS 232 COM2 amp COMA 1x USB 3 0 port via native USB3 controller USB 2x USB 3 0 ports via Renasas uPD720202 USB3 host controller 1x USB 2 0 port Audio 1x Speaker out DIO 4 CH 5V TTL DI 4 CH 5V TTL DO Internal I O Interface Mini PCle 1x mini PCI Express slot with USIM socket Storage Interface SATA HDD 1x internal SATA port for 2 5 HDD SSD Power Supply DC Input Built in 8 35 VDC DC input roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 9 of 78 POC 200 Series User s Manual Input Connector 2 pin pluggable terminal block for DC input Power Consumption Typical 7 68W 0 32A 24V Full loading 13
30. h to the pin 1 and pin 2 of the on board 1x3 pins 2 0mm pitch pin header polarity is negligible Page 54 of 78 Mode Jumper Setting AT 000 ATX DOP POC 200 Series User s Manual 3 When the latched switch is closed the DC power is break off and system is turn off When the latched switch is opened the DC power is feed in and with the correct setting of Power On after Power Failure BIOS option the system is turn on 3 7 3 To Power on POC 200 Using an Non latched Switch ATX mode For an application which places POC 200 inside a cabinet it s useful to control the on off of the system using an external switch POC 200 series provides an on board 3 pin wafer connector for detail please refer to section 2 4 1 for connecting a latched non latched switch and behaves either AT mode or AT X mode power on off control When using the ATX mode on off control you need a non latch switch The external non latched switch acts exactly the same as the power button on the front panel To power on POC 200 using an external non latched switch ATX mode please follow the steps listed below 1 Prepare a non latched switch with a 2 pin 2 0mm pitch connector 2 Connect the non latched switch to the pin 2 and pin 3 of the on board 1x3 pins 2 0mm pitch pin header polarity is negligible o Copyright 2014 Neousys Technology Inc All Right Reserved Page 55 of 78 POC 200 Series User s Manual Mode
31. ing the Power Button This is the simplest way to turn on your POC 200 The power button on the front panel is a non latched switch and behaves the ATX mode on off control As DC power is connected push the power button will turn on the system as well as the PWR LED indicator Push the button when system is on will turn off the system If your operating system supports ATX power mode i e Microsoft Windows or Linux push the power button causes a pre defined system behavior such as shutdown or hibernation o Copyright 2014 Neousys Technology Inc All Right Reserved Page 53 of 78 POC 200 Series User s Manual PWR WDT HDD RESET DIO GPIO 3 7 2 To Power on POC 200 Using an Latched Switch AT mode For an application which places POC 200 inside a cabinet it s useful to control the on off of the system using an external switch POC 200 series provides an on board connector for detail please refer to section 2 4 1 for connecting a latched non latched switch and behaves either AT mode or ATX mode power on off control When using the AT mode on off control you need a latched switch The external latched switch controls the feed in of DC power When the switch is closed the DC power is break off When it s opened the DC power is feed in To power on POC 200 using an external latched switch AT mode please follow the steps listed below 1 Prepare a latched switch with a 2 pin 2 0mm pitch connector 2 Connect the latched switc
32. ion 1 N C No connection 2 N C No connection 3 DI 0 Digital input channel 0 4 N C No connection 5 DI 1 Digital input channel 1 6 DO 0 O Digital output channel 0 7 N C No connection moles Copyright 2014 Neousys Technology Inc All Right Reserved Page 22 of 78 POC 200 Series User s Manual 8 DO 1 O Digital output channel 1 9 DI 2 Digital input channel 2 10 D GND GND Digital GND 11 DI 3 Digital input channel 3 12 DO 2 O Digital output channel 2 13 N C No connection 14 DO_3 O Digital output channel 3 15 N C No connection 16 D_GND GND Digital GND 2 reoLer Copyright 2014 Neousys Technology Inc All Right Reserved Page 23 of 78 POC 200 Series User s Manual 2 3 Back Panel I O Functions To fit more general application requirements POC 200 series offers more I O functions on its back panel In this section we ll illustrate each I O function on the back panel 2 3 1 USB3 0 Connectors There are totally three USB 3 0 ports and one USB 2 0 port on POC 200 series One of three USB 3 0 ports is located on the back panel This USB 3 0 port is implemented via native xHCI controller inside Bay Trail SoC By BIOS default this USB port is operated in xHCI eXtensible Host Control Interface mode and is compatible to USB 3 0 USB 2 0 USB 1 1 and USB 1 0 devices To utilize USB 3 0 function in Windows you need to install corresponding U
33. it BYTE value 0 or 1 to indicate unit of timeout ticks 0 unit is minute 1 unit is second Return Value If value of unit is correct 0 or 1 this function returns TRUE otherwise FALSE Usage WORD tick 255 BYTE unit 1 unit is second BOOL bRet SetWDT tick unit timeout value is 255 seconds StartWDT Description Start countdown of WDT When WDT is started the WDT LED indicator starts to blink in a frequency of 1Hz If no ResetWDT or StopWDT is invoked before WDT is counted to 0 the WDT expires and system resets Parameter None Return Value If the timeout value is given in correct format this function returns TRUE otherwise FALSE Usage BOOL bRet StartWDT ResetWDT Description Reset the timeout value to the value given by SetWDT If no ResetWDT or StopWDT is invoked before WDT is counted to 0 the WDT expires and system resets Parameter None Return Value Always returns TRUE Usage BOOL bRet ResetWDT 2 runs Copyright 2014 Neousys Technology Inc All Right Reserved Page 73 of 78 POC 200 Series User s Manual StopWDT Description Stop the countdown of WDT When WDT is stopped the WDT LED indicator stops blinking Parameter None Return Value Always returns TRUE Usage BOOL bRet StopWDT Using DIO Function Wiring for Isolated DIO POC 200 Only POC 200 supports 4x isolated DI channels and 4x isolated DO channels The isolated DI channels are implemented using photo cou
34. m failed to boot 1 Follow the steps in section 3 1 1 POC 200 210 or section 3 1 2 POC 212 222 to dissemble your POC 200 series You can see the DDR3L socket exposed o Copyright 2014 Neousys Technology Inc All Right Reserved Page 40 of 78 POC 200 Series User s Manual 2 Tile the DDR3L SODIMM module and insert it to the SODIMM socket As it s firmly contacted with socket connectors press it down until the clamps of the socket snap into the latching position of SODIMM module gg gen va99E on ne ma 3 3 Install a 2 5 HDD SSD The SATA port of POC 200 series is located on the daughter board via a 22 pin SATA connector POC 200 210 and POC 212 222 feature different design of HDD mounting bracket To install a 2 5 HDD SSD to your POC 200 series please follow the steps listed below 3 3 1 Install a 2 5 HDD SSD on POC 200 210 1 Follow the steps in section 3 1 1 to dissemble your POC 200 210 You can get the HDD bracket from the chassis assembly 2 Remove the protective firm from the thermal pad on the HDD bracket DD 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 41 of 78 POC 200 Series User s Manual 3 Get four M3 F head screws from the accessory box Attach the HDD SSD to the bracket using four M3 F head screws Another two screws are on the opposite side 4 Gently slide the HDD assembly into the SATA connector till they re firmly connected
35. n This utility automatically detects your Windows operating system and installs all necessary drivers to your POC 200 series with just one mouse Click 4 3 1 Install All Drivers Using One Click Driver Installation 1 Insert the Drivers amp Utilities DVD into a USB DVD drive attached to your POC 200 A setup utility launches and the following dialog appears Automatic Driver Installation Browse this DVD Open User s Manual neousvs Drivers amp Utilities DVD n Exit www neousys tech com 2 Click on the Automatic Driver Installation The setup utility will automatically detect your Windows operating system and install all necessary drivers According to different versions of Windows the installation process takes about 6 8 minutes Once driver installation is done the setup utility reboots your Windows and your system works normally afterward 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 67 of 78 POC 200 Series User s Manual 4 3 2 Install Drivers Manually You can also manually install each driver for POC 200 series Please refer to the following information about installing drivers for different operating system Windows 7 32 bit The recommended driver installation sequence is 1 Chipset driver x Driver_Pool Chipset_Vlv Win7_8 ALL SetupChipset exe 2 Graphics driver x Driver PoollGraphics VIiv EMGDWin7 32VSetup exe 3 Audio driver x Driver_Pool Audio
36. nc All Right Reserved Page 36 of 78 POC 200 Series User s Manual 2 6 4 Bottom View m Im me O M4 Thread 100 00 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 37 of 78 POC 200 Series User s Manual Chapter 3 Getting Start In this chapter welll illustrate how to disassemble your POC 200 and install peripheral devices Please note that the procedures might be varied for different POC 200 models Please follow the correct procedures to prevent any damage on your POC 200 series 3 1 Dissemble your POC 200 Series 3 1 1 Dissemble POC 200 210 1 Unscrew 4 hex bolts on the top of the heat sink 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 38 of 78 POC 200 Series User s Manual 3 Gently slide out the assembly of case and you can see the case and the HDD bracket 3 1 2 Dissemble POC 212 222 1 Unscrew the hand screw on the back panel 2 Pull the 2 5 HDD bracket out of POC 212 222 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 39 of 78 POC 200 Series User s Manual 3 Unscrew 4 hex bolts on the top of the heat sink 4 Gently slide out the assembly of case 3 2 Installa DDR3L SODIMM Module Note Please make sure you re installing a 1 35V DDR3L SODIMM module on POC 200 Installing a 1 5V DDR3 SODIMM will cause syste
37. ne aaa 36 2 6 4 Bottom View RE 37 Chapter 3 Getting Sidoli 38 3 1 Dissemble your POC 200 Series ola lla are 38 3 1 1 Dissemble POC 200 210 criar 38 3 1 2 Dissemble POC 212 222 suuusnsnsenemnmanenussqh enidnsiat 39 3 2 Install a DDR3L SODIMM Module aana nean nne e anane nana e ena ee nne 40 33 Installa 2 5 HDD SSD sasi aaa kaa kaajeng ee cece es aaa asa ija pang ia aa kaa aa ea ana iba ka aa aa ea aga dia an 41 3 3 1 Install a 2 5 HDD SSD on POC 200 210 i 41 3 3 2 Install a 2 5 HDD SSD on POC 212 222 iii 43 3 4 Install Mini PGle Module 22 44 3 4 1 Install a Mini PCle Module on POC 200 POC 210 44 3 4 2 Install a Mini PCle Module on POC 212 222 ii 46 3 5 Mount your POC 200 Series 48 3 5 1 Suspend your POC 200 on the Wall i 48 3 5 2 Mount your POC 200 Outside in on a Surface 49 3 5 3 Mount your POC 212 222 Inside out on a Surface 50 3 5 4 Mount your POC 200 on the DIN Rail renerne erne 51 3 6 Connect DC power to you POC 200 i 52 3 7 Power on your PO 200 eee 53 3 7 1 To Power on POC 200 Using the Power Button 53 3 7 2 To Power on POC 200 Using an Latched Switch AT mode 54 3 7 3 To Power on POC 200 Using an Non latched Switch ATX mode 55 3 7 4 To Po
38. nnect GigE USB3 cameras for vision applications Its IEEE 802 3at PoE option is capable to supply 25 5W each port to power you IP camera for surveillance applications POC 200 series also features up to four COM ports and digital I O for general purpose industrial applications Size is another attractive feature of POC 200 Its 6 x4 footprint makes installation of POC 200 extremely easy And its 30 C to 70 C operating temperature eliminates the restriction for deployment environment Neousys provides derivative models with different CPU and I O configuration so you can always find a fit POC 200 for your application 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 7 of 78 POC 200 Series User s Manual 1 2 Product Specification 1 2 1 Specification of POC 200 System Core Processor Intel Atom E3845 1 91 GHz quad core processor Graphics Integrated Intel HD Graphics Memory 1x SODIMM socket for DDR3L 1333 up to 8GB Panel I O Interface Ethernet 2x Gigabit Ethernet ports by Intel 1210 GbE controller PoE IEEE 802 3at PoE PSE 25 5W each GbE port 1x DVI I connector for both analog RGB and DVI HDMI outputs supporting up to Video Port 2560 x 1600 resolution 2x software programmable RS 232 422 485 COM1 amp COM3 Serial Port 2x RS 232 COM2 amp COM4 1x USB 3 0 port via native USB3 controller USB 2x USB 3 0 ports via Renasas uPD720202 USB3 host co
39. ntroller 1x USB 2 0 port Audio 1x Speaker out DIO 4 CH isolated DI 4 CH isolated DO Internal I O Interface Mini PCle 1x mini PCI Express slot with USIM socket Storage Interface SATA HDD 1x internal SATA port for 2 5 HDD SSD Power Supply DC Input Built in 8 35 VDC DC input Input Connector 2 pin pluggable terminal block for DC input Power Consumption Typical 7 68W 0 32A 24V Full loading 13 44W 0 56AQ24V Mechanical Dimension 149mm W x 105 mm H x 58 mm D Weight 1 1 kg with one 2 5 SATA HDD Mounting Wall mount Standard DIN rail mount Optional Environmental Operating Temperature 30 C gt 70 C with SSD 100 CPU loading 10 C 60 C with HDD 100 CPU loading SSS Copyright 2014 Neousys Technology Inc All Right Reserved Page 8 of 78 POC 200 Series User s Manual Storage 40 85 C Temperature Humidity 10 90 non condensing Vibration Operating 5 Grms 5 500 Hz 3 Axes w SSD wo add on card according to Shock Operating 50 Grms Half sine 11 ms Duration w SSD w o add on card according oc to IEC60068 2 27 EMC CE FCC Class A according to EN 55022 amp EN 55024 Full loading power consumption is measured with 2GB DDR3 memory and one 2 5 SATA HDD installed under the following conditions 100 loading for Atom E3845 CPU 100 loading for 3D graphics 10026 loading
40. og appears 1 Setup Neousys Nuvo Nuvis POC Series WDT amp DIO Library 3 Welcome to the Neousys Nuvo Nuvis POC Series WDT amp DIO Library Setup Wizard This will install Neousys Nuvo Nuvis POC Series WDT amp DIO Library version Ver 2 00 on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 70 of 78 POC 200 Series User s Manual Click Next gt and specify the directory of installing related files The default directory is C Neousys WDT_DIO I Setup Neousys Nuvo Nuvis POC Series WDT amp DIO Library amp Select Destination Location Where should Neousys Nuvo Nuvis POC Series WDT amp DIO Library be installed a Setup will install Neousys Nuvo Nuvis POC Series WDT amp DIO Library into the following folder To continue click Next If you would like to select a different folder click Browse C INeousys WDT DIO Browse At least 1 3 MB of free disk space is required Once the installation is finished a dialog appears to prompt you to reboot the system The WDT amp DIO library will take effect after system rebooting 1 Setup Neousys Nuvo Nuvis POC Series WDT amp DIO Library E 33 Completing the Neousys Nuvo Nuvis POC Series WDT amp DIO Library Setup Wizard To complete the installa
41. or inductive load 3 DL 0 Digital input channel 0 4 VDD DO voltage source input for inductive load 5 DI 1 Digital input channel 1 6 DO 0 O Digital output channel 0 7 DI GND Digital input GND 8 DO 1 O Digital output channel 1 9 DL 2 Digital input channel 2 10 DO GND Digital output GND 11 DI 3 Digital input channel 3 12 DO 2 O Digital output channel 2 13 DI GND Digital input GND 14 DO 3 O Digital output channel 3 15 DI_GND i Digital input signal 16 DO GND Digital output GND Electrical Characteristics Parameeter Description Min Typ Max DO Channel 0 3 V DO DO output voltage 24 V DO DO current limit 100 250 mA DI Channel 0 3 V_DI High Input voltage High 5 24 V V_DI Low Input voltage Low 0 1 5 V DI Input current 20 mA Voltage ISO 5V V_ISO5V Voltage 4 75 5 5 25 V 2 renuens Copyright 2014 Neousys Technology Inc All Right Reserved Page 21 of 78 POC 200 Series User s Manual ISOSV Current 200 mA Input Parameter Resistor Input resistor 2 4 Kohm Isolated voltage 2500 V rms 2 2 9 2 5V TTL GPIO on POC 210 POC 212 POC 222 DIO GPIO POC 210 212 222 offers 8 CH 5V TTL GPIO for general purpose usage By default these channels are configured as 4 channels of digital input and 4 channels of digital output The following table describes the pin definition of isolated DIO connector 2 16 1 15 Pin Definition Pin Definition I O Descript
42. plers with internally series connected 2 4kO resistors You need to provide a voltage to specify the logic high low state The input voltage for logic high is 5 24V and the input voltage for logic low is 0 1 5V Digital Input 2 4K Ey 4 I basasseessessesosesse a J The isolated DO channels are implemented using Power MOSFET Analog Device iCoupler amp component The DO channels are configured as NO normally open configuration When you turn on system all DO channels have a deterministic state of logic 0 circuit disconnected from GND return When logic 1 is specified MOSFET is activated 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 74 of 78 POC 200 Series User s Manual and GND return path is established The isolated DO on POC 200 supports sinking current connection The following diagrams are the suggested wiring for DO N NN gel i NS nd om Sink Ce aia caw a ee ee ee ee ee a ed Pin Definition for Isolated DIO POC 200 Only 2 16 1 15 Pin Definition Pin Definition I O Description 1 ISO 5V O Isolate 5V power supply 2 VDD DO voltage source input for inductive load 3 DL 0 Digital input channel 0 4 VDD DO voltage source input for inductive load 5 DI 1 Digital input channel 1 6 DO 0 O Digital output channel 0 7 DI GND Digital input GND 8 DO 1 O Digital output channel 1
43. r Failure Option This option defines the behavior of POC 200 series when DC power is supplied Value Description 50 Power On System is powered on when DC power is supplied 55 Power Off System is kept in off state when DC power is supplied When you want to use the AT mode remote on off control function you have to set this option to SO Power On Please refer to section 3 7 2 for instructions of using AT mode remote on off control function To set Power On after Power Failure option 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Power 3 Set the Power On after Power Failure option to a proper value for your POC 200 Power On after Power Failure lt S5 Power Off gt 0 Power On 4 1 7 Watchdog Timer for Booting The BIOS of POC 200 series has a useful feature which allows users to use the watchdog timer to secure the booting process You can specify the timeout value for watchdog timer Once the watchdog timer expires the BIOS issues a reset command to initiate another booting process You can also set the behavior of how to stop the watchdog timer There are two options in BIOS menu Automatically after POST and Manually after Entering OS When Automatically after POST is selected the BIOS automatically stop the watchdog timer after POST Power On Self Test OK When Manually after Entering OS is selected it s user s responsibility
44. rt on POC 200 series Two of three USB 3 0 ports are located on the front panel They are implemented via a Renasas uPD720202 USB3 host controller By BIOS default these USB ports are operated in xHCI eXtensible Host Control Interface mode and are compatible to USB 3 0 USB 2 0 USB 1 1 and USB 1 0 devices Legacy USB support on these ports is provided only when xHCI Mode option in BIOS is configured as Smart Auto To utilize USB 3 0 function in Windows you need to install corresponding driver for Renasas uPD720202 USB3 0 controller Please refer to section 4 3 for information of driver installation 2 2 5 Speaker out Jack DIO GPIO POC 200 series provides speaker out function using Intel High Definition Audio built in in ICH8 M and Realtek ALC262 codec An audio jack is located on the front panel To utilize 2 o Copyright 2014 Neousys Technology Inc All Right Reserved Page 17 of 78 POG 200 Series User s Manual the speaker out function in Windows you need to install corresponding drivers for both Intele ICH8 M chipset and Realtek ALC262 codec Please refer to section 4 3 for information of driver installation 2 2 6 Gigabit Ethernet Ports DIO GPIO POG 200 series offers two Gigabit Ethernet ports using Intele 1210 GbE controller When plugging in the Ethernet cable you can tell the Ethernet status and speed from the LED indicators on the RJ45 connector as following Active Link LED LED Color Stat
45. s listed below 1 Make sure the external DC power supply is power off or disconnected before wiring 2 Get the 2 pin pluggable terminal block from the accessory box The terminal block fits the wires with a gauge of 12 24 AWG 3 Carefully identify the positive and negative contacts of your DC power supply and pluggable terminal block The polarities between DC power supply and terminal block must be positive to positive and negative to negative 4 Find the 2 pin power plug on the PCBA which accepts the terminal block It s located on the right side of back panel roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 52 of 78 POC 200 Series User s Manual 5 Push the terminal block to the power plug till it s firmly attached Now you can supply the DC power and operate your POC 200 Caution 1 POC 200 accepts 8 35 VDC when using terminal block for DC input Please make sure the voltage and polarity of DC power is correct before you connect it to POC 200 Supplying a voltage over 35V will damage the system 3 7 Power on your POC 200 For better flexibility of operation POC 200 series provides four alternatives to power on your POC 200 You can turn on your POC 200 by pressing the power button using an external latched or non latched on off switch or by sending a special LAN packet In this section we ll illustrate these four ways to power on your POC 200 3 7 1 To Power on POC 200 Us
46. s with all applicable European Union CE directives if it has a CE marking For computer systems to remain CE compliant only CE compliant parts may be used Maintaining CE compliance also requires proper cable and cabling techniques Copyright and Trademarks This document contains proprietary information protected by copyright All rights are reserved No part of this document may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer Company product names mentioned herein are used for identification purposes only and are trademarks and or registered trademarks of their respective companies 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 6 of 78 POC 200 Series User s Manual Chapter 1 Introduction 1 1 Overview POC 200 series is a breakthrough of Neousys ultra compact controller series Inheriting the concept of favorable POC 100 POC 200 series further incorporates greater computing power and more versatile functions in its 3 5 HDD footprint The new Intel Atom Bay Trail I platform brings a leaping for both arithmetic and graphics performance With Atom E3845 quad core processor POC 200 can deliver more than 200 performance over previous D525 D2550 platform It also feature comprehensive I O interfaces to make use of the advance of computing power Two Gigabit Ethernet and three USB 3 0 ports are integrated so you can co
47. scription Read a single channel of isolated digital input Parameter ch BYTE value specifies the DI channel to be read ch should be a value of 0 3 Return Value The status TRUE or FALSE of the specified DI channel Usage BYTE ch 3 DI channel 3 BOOL DIChValue DIReadLine ch read DI channel 3 DIReadPort Description Read the entire isolated digital input port 4 channels Parameter None Return Value A WORD value indicates the status of DI port 4 DI channels Usage WORD DiPortValue DIReadPort DOWriteLine Description Write a single channel of isolated digital output Parameter ch BYTE value specifies the DO channel to be written 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 77 of 78 POC 200 Series User s Manual ch should be a value of 0 3 value BOOL value TRUE or FALSE specifies the status of DO channel Return Value None Usage BYTE ch 3 DI channel 3 BOOL DOChValue TRUE DOWriteLine ch DOChValue write DO channel 3 as TRUE DOWritePort Description Write the entire isolated digital output port 4 channels Parameter value WORD value specifies the status of the DO port value should be a value of 0 15 Return Value None Usage WORD DOPortValue 0x0C 1100b DOWritePort DOPortValue write DO port as 1100b 2 reoLer Copyright 2014 Neousys Technology Inc All Right Reserved Page 78 of 78
48. tion of Neousys Nuvo Nuvis POC Series WDT amp DIO Library Setup must restart your computer Would you like to restart now No I will restart the computer later o Copyright 2014 Neousys Technology Inc All Right Reserved Page 71 of 78 POC 200 Series User s Manual 4 When you programming your WDT or DIO program the related files are located in Header File Include e Library File Lib Function Reference Manual Sample Code Sample WDT_Demo Watchdog Demo Sample DIO_Demo Sample COS_Demo Sample DTIO_Demo Sample DTFO_Demo Sample PoE_Demo Polling I O Demo Change of State Interrupt Demo DTIO Demo Trigger Fan out Demo PoE per port Control Demo PO o SS Using WDT Function WDT Function Reference InitWDT Description Initialize the WDT function You should always invoke InitWDT before set or start watchdog timer Parameter None Return Value Returns TRUE ff initialization successes FALSE if initialization failed Usage BOOL bRet InitWDT SetWDT Description Set timeout value and unit for watchdog timer When InitWDT is invoked a default timeout value of 255 seconds is assigned Parameter tick WORD value to indicate timeout ticks tick should be a value of 1 16 if unit is 0 minute tick should be a value of 6 1027 if unit is 1 second 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 72 of 78 POC 200 Series User s Manual un
49. to stop the watchdog timer when entering OS This 2 roe Copyright 2014 Neousys Technology Inc All Right Reserved Page 63 of 78 POC 200 Series User s Manual guarantees the system can always boot to OS otherwise another booting process will be initiated For information about programming watchdog timer please refer to Appendix A Using W Watchdog Timer and DIO To set the watchdog timer for boot in BIOS 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Boot menu 3 Disable or select timeout value for WDT for Booting option 4 Once you give a timeout value the WDT Stop Option option appears You can select either Automatically after POST or Manually after Entering OS WDT Stop Option lt Automatically after POST gt Automatically after POST 4 1 8 Select a Boot Device When you have multiple bootable devices connected to your POC 200 i e HDD USB flash disk USB DVD drive you may need to select one of them as the first boot device There are two ways to select the device You can either press F12 when system boots up to go to Boot Manager and then select one of the devices or select the boot device in BIOS settings To select a boot device in BIOS 1 When POC 200 boots up press F2 to enter BIOS setup utility 2 Goto Boot gt Boot Device 3 The Boot Menu option determines whether to list all bootable devices connected to your POC 200 according to device or devic
50. us Description Yellow Off Ethernet port is disconnected On Ethernet port is connected and no data transmission Flashing Ethernet port is connected and data is transmitting receiving Speed LED LED Color Status Description Green or Off 10 Mbps Orange Green 100 Mbps Orange 1000 Mbps To utilize the GbE port in Windows you need to install corresponding driver for Intele 1210 GbE controller Please refer to 4 3 for information of driver installation 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 18 of 78 POC 200 Series User s Manual 2 2 7 IEEE 802 3at PoE PSE POC 200 Only nio SECTEGOD 4 WO ceccrceo f EM GO EG GS PoE or Power over Ethernet is a technology to supply electrical power along with data on a standard CAT 5 CAT 6 Ethernet cable Two Gigabit Ethernet ports on POC 200 support IEEE 802 3at PoE PSE Power Sourcing Equipment function Each PoE port can deliver 25 5 W of power to a PoE PD Powered Device such as a PoE IP camera or a PoE WIFI AP PoE defines a mechanism to automatically detect the device connected and determine whether to dispatch power This makes PoE port 100 compatible with traditional Ethernet devices thus you can use these ports to connect PoE or non PoE devices 2 2 8 DVI I Connector DIO GPIO POC 200 series features a DVI I connector on its front panel to output both VGA and DVI HDMI signals Th
51. wer on POC 200 Using Wake on LAN Function 56 Chapter 4 BIOS and Driver uuuan asmeieneriemnsebentesm ju nana eaaa nana nane nenen 59 4 1 BIOS Settings lla ii 59 4 1 1 COM1 Operation Mode i 59 4 1 2 COM3 Operation Mode POC 200 210 Only i 60 4 1 3 Chipset SATA Mode 61 4 1 4 C States and Max C States ii 61 4 1 5 Wake on LAN Option 62 4 1 6 Power On after Power Failure Option ii 63 4 1 7 Watchdog Timer for Booting nr nana aana nane 63 2 runs Copyright O 2014 Neousys Technology Inc All Right Reserved Page 4 of 78 POC 200 Series User s Manual 4 1 8 Select a Boot Device 64 4 2 Operating System Support i 66 BS T V eg ele 67 4 3 1 Install All Drivers Using One Click Driver Installation 67 4 3 2 Install Drivers Manually aaa ea eaaa cre 68 Appendix A Using Watchdog Timer and DIO 70 Install WDT and DIO ben eee 70 Using WDT EEE 72 WDT Function Reference ucraini 72 WWD PER EE EE E 72 MGW VOT ER ecole ieee aa RA 72 SAN 73 RESCNIDT collera 73 Te 74 Using DIO FURcioi isla 74 Wiring for Isolated DIO POC 200 Only cece eeeeeeeceee nana aaa en anana aane nane 74 Pin Definition for Isolated DIO POC 200 Only ceeeeeeeeeeeeeeeeeetteeeeeeees 75 Pin Definition for 5V TTL GPIO POC 210 212 222 aana anana eee 7
52. xe 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 68 of 78 POC 200 Series User s Manual 4 LAN driver x Driver_Pool GbE_1210 Win7_8 64 APPS PROSETDX Winx64 DxSetup exe 5 TXE driver x Driver_Pool TXE_VIv Win8_ALL SetupTXE exe 2 roles Copyright 2014 Neousys Technology Inc All Right Reserved Page 69 of 78 POC 200 Series User s Manual Appendix A Using Watchdog Timer and DIO POC 200 series provides watchdog WDT timer function to ensure reliable system operation WDT is a hardware mechanism to reset the system if the watchdog timer is expired Users can start WDT and keep resetting the timer to make sure the system or program is running flawlessly Otherwise the system shall be reset POC 200 series also supports isolated DIO POC 200 or 5V TTL GPIO POC 210 21 2 222 for extended range of applications DIO on POC 200 series supports standard polling mode I O access Users can read or write DIO channel s in their applications In this chapter we ll illustrate how to use the WDT DIO function library provided by Neousys to program the WDT and DIO functions Install WDT and DIO Library The WDT DIO function library is delivered in the form of a setup package For POC 200 series please use WDT DIO Setup v2 0 4 exe or later revision In prior to program WDT and DIO on POC 200 series you should execute the setup program and install the library 1 Execute WDT DIO Setup exe The following dial

POC-200 Series User's Manual Rev A1.1

Contents

Download Pdf Manuals

Related Search

Related Contents