Fluxient Bicycle Light User Manual Model: 3XU2 Fluxient electric
Contents
1. Fluxient Bicycle Light User Manual Model 8XxU2 Fluxient electric appliance Co Ltd Add 124 East Street Qingshuijou Village Haochuan Block Zhenhal District Ningbo City Zhejiang Province China Zip code 375227 Contact Alwin Wu Tel 86 13656780095 Fax 86 5 4 86382908 E mail alwin tluxient cn Website www fuxrent cn GUU EENET Please read this user manual to completely familiarize you with this product Make sure you understand all functions before hitting the trails 1 Please Read Before Use Cycling in the dark is inherently dangerous Always make sure the light is firmly secured and the battery is fully charged before you go for a ride Like all other electronic devices the light can fail at any unexpected time It is advised to always keep a backup light and battery pack with you whenever you go on an extended ride Please note that your Fluxient light is very bright never aim it directly at any oncoming motorists cyclists Your Fluxient bicycle light is equipped with a high capacity Lithium ion battery pack Please completely charge the battery before first use of the light While the battery pack is double protected you should always observe the following e While charging the batteries never leave it unattended for a long time e Only use the Fluxient charger to charge the batteries Using other chargers to charge Fluxient batteries may cause battery failure and or other serious damage Your Fluxient2. levels Max 3000 lumens Medium 1500 lumens Low 700 lumens Runtime Max 2 7 hours Medium 6 hours Low 12 hours Battery capacity Voltage 7 4V 8x18650 quality Li ion battery cells water resistant design Charger 8 4V 2A output fast charger Charge time 4 5 hours Shell material Aircraft Grade Aluminum alloy Mount 25 2 to 31 8 mm Bar Waterproof Grade P65 Weight 196g without battery pack 596g with battery pack Package Includes head light battery pack charger extension cable handlebar mount allen wrench Velcro tape and storage bag 9 Manufacture Warranty 2 Years for the Light Charger Battery Pack Mount and extension wire Crashes and mis handling are not covered
3. bicycle light uses high power U2 LEDs which in high mode generate a significant amount of heat The aluminum body is designed to draw most of the excess heat away The light head may get extremely hot during this process if sufficient air flow is not provided Please use with caution NOTE The over heating protection circuit will automatically reduce the high bright level to low in the event of over heating When the temperature returns to the normal operating range full bright will automatically resume 2 Charging the battery pack The battery pack is shipped half charged You need to fully charge it before first use e Connect the battery to the charger the charger LED will turn Green e Plug the charger into the power outlet the charger LED will turn Red indicating that the battery is charging A full charge from empty will take approximately 4 5 hours e Once fully charged the LED will turn Green Unplug the charger and disconnect the battery 3 Handle Bar Mounting e Remove the screw from the handlebar mount and install the mount on the bar with the release tab facing forward e The rubber strip spacers included are used to achieve a proper fit to your handlebars The spaces can be trimmed with scissors to achieve a good solid fit e Re install the mounting screw and tighten as needed to secure the mount Don t over tighten The nut shouldn t show more than two threads above the surface If too much thread is protruding the li
4. for you e The switch is illuminated while plugged in which makes it easy to locate in the dark e The light starts in the OFF mode e Quick Push the switch button for High Medium Low and Strobe e Push and hold the switch button for two seconds from any setting to turn the light OFF 5 Battery Level Indicator As the battery depletes the backlit switch button will change color from Blue to Red Blue 100 20 Red 20 0 6 Battery Storage FUL ARI Disconnect the battery pack from the light head when not using Store the battery pack fully charged and re charge it before using the lighting system again If not used for an extended period of time please store the battery pack in a cool dry place to avoid excessive discharge 7 Troubleshooting No light Caused a is over discharged Solution y the batter Battery is not plugged in Make sure all parts are firmly correctly connected Running time too short Defective charger Replace the charger Cables not secured Make sure all parts are firmly connected 8 Technical Data LED 3 Cree XML U2 LED s LED lifespan 50 000 hours Brightness 3000 lumens Range 500m Lens High transparent Hardened Glass Modes 3 level adjustable brightness amp flashing Over heat protection function If the unit overheats the light will auto power down to 30 until the temp cools then it will auto power back up to 100 This is to save the LED s and Battery Output
5. ght will not slide onto the mount Simply add an additional piece of rubber strip as needed install the mount on the 31 8mm bar no need add any rubber strip Cut strip spacers as needed LIU EENET e Install the light to the mount flow the slot and direction as the photo When you wan to take light down from mount put the button and move the light to the back e Find the most suitable place for mounting the battery If you have a long enough stem this is the best place to put it otherwise you can mount it to your bike frame or handlebars Opposite side to where the light is e Estimate how much cable length you will require and then secure up the excess cable e Wrap the Velcro strap around the stem frame handle bars at the same time securing the excess cable with a Velcro strap e Plug the light cable into the battery cable x we h S PN f S Install light on mount Take light down Frame mount battery pack Stem mount battery pack Handlebar mount battery pack Operating Fluxient 3XU2 light WARNING Use common since when installing your lights and make sure that your light cables and battery don t interfere with the proper use of your handlebar or the control levers Your handlebars should be able to turn full left right without binding or stretching cables or interfering with the controls If you re not comfortable about your installation please have your Local Bike Shop install the lights
Download Pdf Manuals
Related Search