Home

OWNERS MANUAL - nuance Veranstaltungstechnik GmbH

image

Contents

1. BUZZ ON OFF _ Switch we turn on off the vibrator If the vibrator itis in on mode the vibrator Ox turn to off mode and if the vibrator itis in off mode the vibrator turn to on mode If the vibrator itis turned on when a call is received the unit vibrates The state of the VIBRATOR on off itis stored in the unit STANDBY MODE When the beltpack is turn off and we press the ON OFF Q switch and the VOLUM E DOWN 4 switch atthe same time the l beltpack change to ww STANDBY mode In this mode the beltpack can receive CALLs but the audio itis disconnected This mode is useful to save battery since the beltpack less consumes 5 times than in full duplex state To exit from STANDBY mode press shorted the ON OFF switch MIC GAIN USTMENT The mic gain adjustment allows attenuating or amplifying the mic signal When press the MIC ON OFF switch and awe at the same time the UP or DOWN VOLUME switch the mic Om gain itis adjusted the four leds of the beltpack turn to indicate the mic gain There are 15 steps of mic gain the LOW BATTERY led indicates the first step the BUZZ ON OFF led indicates the o sixth step the MIC ON OFF led indicates the eleventh step and the IN RANGE led the fiveteenth step ofthe mic gain The MIC GAIN it is stored in the unit SIDETONE GAIN ADJ USTMENT The sidetone gain adjustment allows attenuating or amplifying the own mic signal that we listen in our headphones When pres
2. EF 200 connected to the base station This MIC KILLsystem is compatible with other intercom systems of the market The state of the MIC on off itis stored in the unit BUZZER ON OFF SWITCH This switch Ou enables disables the buzzer sound when the unit receives a call and when the user press a key Whenever this switch is pressed and the buzzer is enabled it will be disabled and the LED indicator will turn off On the other hand if the buzzer was disabled it will be enabled and the LED indicator will lighten up The buzzer also sounds when any switch is pressed emitting a short hoot when itis enabled The unit provides a BUZZER KILL turns off the BUZZER system so that when the buzzer is enabled itis possible to muted it by the BUZZER KILL function of the base station ALTAIR WBP 200 or a master station ALTAIR EF 200 connected to the base station This BUZZER KILL system is compatible with other intercom systems of the market The BUZZER could be disabled with an internal preset In order to obtain more information consultthe special operation section The state of the BUZZER on off itis stored in the unit VOLUME UP DOWN SWITCH The volume switches Y allows attenuating or amplifying the signal sent to the headphones This switches adjusts the listen level to the headphones as you wish When volume UP DOWN switches are pressed the four leds ofthe beltpack turn to indicate the volume There are 10 steps of volume
3. altair altairaudio com www altairaudio com
4. SWIICH 6 VOLUME UP DOWN SWIICH 6 ON OFF SWIICH 6 IN RANGE LED 7 VIBRATOR ON OR 7 STANDBY MODE 7 MIC GAIN ADJ USTMENT I 7 SIDETONE GAIN ADJ USTMENI 7 BELTPACK REGISTRATION 7 BELTPACK DEREGISTRATION 8 DC IN CONNECTOR 8
5. a jumper JP1 BUZZER located near the buzzer on the upper right side of the unit This jumper defeats the actions of the buzzer key and remote buzzer key It is convenient to place the jumper over one pin for future use Disabling the buzzer quarantees no CALL sounds in any circunstance as desired in theatre or any other public performance CHANGING THE BATTERIES The wireless case includes three NiMh 12 V batteries of size AAA and capacity of 900 mA h In the case it mustbe replaced one battery replaces all atthe same time by three equal batteries The beltpack can work in case of necessity with three alkaline batteries 1 5 V size AAA but it considers that the batteries cannot be charged Don t try to use the unit with no batteries or batteries in bad condition the unit can be damage When necessary the unit can be used when charging at the same time You can either plug the charger when the unit is ON or switch ON the unit when in charging 5 SPECIAL RECOMMENDATIONS Don t place the unit in close proximity to metallic surfaces and or other electronic equipment in order to avoid interferences In case of lose of range reorient your body position to face up the base unit position Take special attention to the placement of the base station when trying to reach all the possible placements of the beltpacks specially when concrete walls or other absorbing materials are in between Q c AE WBP 200 SINGLE CHANNEL WIRELESS BELT
6. low power circuitry Out of range indication helps the user to understand radio coverage and anticipate to possible communication failures 710 HOURS battery life in full duplex Before beginning itis importantto read this manual This manual will help you to install and use your new beltpack It is very importantto read it carefully mainly the paragraphs marked as NOTE PRECAUTION and DANGER for your security Save the original packing you can re use itto transportthe unit NEVER SHIP THE ALTAIR WBP 200 WITHOUT ITS ORIGINAL PACKING E WBP 200 SINGLE CHANNEL WIRELESS BELTPACK 4 2 SWITCHES CONTROLS ADJ USTMENTS AND CONNECTORS These are the switches controls adjustments and connectors that you can find in your ALTAIR intercom beltpack The description and explanation of each one will be found in the corresponding section FRONT PANEL CALLSWITCH MIC SWITCH BUZZER SWITCH ON OFF SWITCH or VOLUMEUP DOWN 1 IN RANGELED 9 LOW BATLED DC IN CONNECTOR o HEADSET CONNECTOR 3 OPERATION The WB 200 series intercom system are designed to allow maximum easy communications operation between the different control areas in music or theatre live performances television cinema conference halls and whatever broad events where multiple and fastcommunications are required by means of its simultaneous listening speaking operation system The Single Channel Wirel
7. the LOW BATTERY led indicates the first step the BUZZ ON OFF led indicates the fourth step the MIC ON OFF led indicates the seventh step and the IN RANGE led the tenth step of volume The VOLUME itis stored in the unit ON OFF SWITCH When the beltpack is power off and the beltpack s O on off switch itis pressed all the beltpack leds lighton and lasta little while itwill sound the buzzer if buzzer is turn on and will vibrate if the vibrator is turn on indicating that 5 itis operative If the base on which itis registered finds within its reach the LED of INRANGE will begin to blink and the audio will be opened Atthis moment you can begin to use your beltpack ALTAIR WBP 200 To turn off the beltpack press and hold two seconds the ON OFF switch when the beltpack is turned In this moment will sound the buzzer if the buzzer is turn when the ON OFF switch itis depressed the beltpack itis turned off If the ON OFF switch itis short pressed the beltpack will show us the battery status LOW BAT led 10 BUZZ ON OFF led 40 MIC ON OFF led 70 and IN RANGE led 100 WBP 200 SINGLE CHANNEL WIRELESS BELTPACK Za ME x IN RANGE LED The IN RANGE led when blinks indicates that the beltpack is in the station base range if itis tum on without blinking indicates thatthe beltpack is notin the station base range VIBRATOR ON OFF When we press atthe same time the MIC ON OFF switch
8. PACK 10 5 TECHNICAL SPECIHCATIONS PREAMPLIHER MICROPHONE TYPE NOMINAL MAXIMUM LEVEL e 45 dBu Hy 20 dBu D PHANTOM VOLTAGE e 49 VDC internal preset e 1900 MHz band e 422 dBm typically TYPE CHARGING TIME CHARGER SIDETONE CANCELLATION e Adjustable 42 30 dB 1KHz e Call Volume level Mic On Off PTT e Call Battery status Low Batt Mic On Off INDICATORS Buzz On Off In range led CALSYSEM Light Vibration and Buzzer DIMENSIONS e 120 80 25 mm WEHGHT o y j oea NOTE Technical specifications are subjectto variation without previous notice WBP 200 SINGLE CHANNEL WIRELESS BELTPACK 6 WARRANTY This unitis warranted by Equipos Europeos Electr nicos to the original user against flaws in the manufacturing and in the materials for a period of one year starting from the date of sale Flaws due to wrong use ofthe unit internal modifications or accidents are not covered by this warranty There is no other warranty expressed or implicit Any faulty unit must be sentto the dealer or the manufacturer The serial number of the unit must be included for any requestto the technical service Equipos Europeos Electr nicos reserves the rightto modify the prices or the technical specifications without further notice ALDCRECIRONCSLESQN EQUIPOS EUROPEOS ELECTR NICOS S A L Avda de la Industria 50 28760 TRES CANTOS MADRID SPAIN cm 34 91 761 65 s 34 91 804 43 s
9. SPECIAL OPERATIONS 8 ACTIVATING THE MICROPHONE PHANTOM POVR 9 CHANGING THE BATITERIES 9 5 TECHNICAL SPECIRCATIONS D 6 WARRANTTY 1 Re a WBP 200 SINGLE CHANN EL WIRELESS BELIPACK 3 1 INTRODUCTI Congratulations on your purchase of the ALTAIRsingle channel wireless beltpack WBP 200 of the WB 200 series wireless intercom system There is a lot the characteristics that make of the ALTAIR WB 200 series one of the most highlighted in the audio professional market some are enumerated here Dual pre amble diversity antenna system detects and selects the higher radio signal ensuring better coverage and minimum dropouts Digital encryption process allows high security conversations Beltpack uses internal antennas for a more comfortable belt fitting As a battery dependant device special care has been taken as battery status indication with led bargraph low consumption call receive mode and general
10. WBP 200 SINGLE CHANNEL WIRELESS BELTPACK WB 200 SERIES WIRELESS INTERCOM SYSTEM ALJICR ECIRONCSLESQN EQUIPOS EUROPEOS ELECTR NICOS S A L Avda de la Industria 50 28760 TRES CANTOS MADRID SPAIN HE 34 91 761 65 30 gie 34 91 804 43 58 et altair altairaudio com www altairaudio com WBP 200 SINGLE CHANN EL WIRELESS BELTPACK 7 1 INTRODUCTION 3 2 SWITCHES CONTROLS ADJ USTMENTS AND CONNECTORS 4 FRONT PANIA 4 REAR 4 3 OPERATION 4 HEADSET CONNECTION 5 CALL SWIICH 5 ON OFF PUSH TO TALK SWITCH TALLK 5 BUZZER ON OFF
11. e higher the time that the switch is pressed and approximately 3 seconds more If a call signal is generated in an external unit wireless beltpacks beltpacks base stations desk stations master stations etc the LED associated with the CALL switch will start blinking and if the buzzer is enabled see buzzer on off section for more information an intermittent sound will take place during aboutthree seconds MIC ON OFF PUSH TO TALK SWITCH TALK The MIC switch allows to enable disable the microphone so that we are able to speak with other units connected to the same intercom channel If the microphone is activated its associated LED will light up and on the other hand if itis disabled its associated LED will turn off Re ee WBP 200 SINGLE CHANNEL WIRELESS BELIPACK 6 The TALK switch has two operation modes When this switch is pressed quickly the microphone changes its state ifit was enabled upon being pressed it gets disabled and turns off the associated LED and if itwas disabled upon being pressed gets enabled and turns on the associated LED When the TALK switch is pressed and held the unit will enter in the special function PUSH TO TALK this means that the microphone will be enabled until the switch is released The unit provides a MIC KILL turns off the MIC system so that when the mic is enabled itis possible to muted it by the MIC KILL function of the base station ALTAIR WBP 200 or a master station
12. ess Beltpack WBP 200 unit was designed for intensive use in portable applications An unbreakable plastic belt clip enables easy and secure suitability Call signalling is Dual visual and audible for improving adaptability The unit can be configured for dynamic or electret microphones enabling the use of different types of headsets and hands free earpieces in the market The WBP 200 is provided with a ON OFF switch a switch a MIC on off switch BUZZER on off switch headphones volume control etc In order to begin to use its new beltpack ALTAIR WBP 200 first it turn on the base station on which the beltpack is registered if itis not registered to any base goes to the registry section WBP 200 SINGLE CHANNEL WIRELESS BELTPACK 5 Once tum on the base station push the on off switch o of the beltpack All the beltpack leds light on and lasta little while it will sound the buzzer if buzzer is turn on and will vibrate if the vibrator is turn on indicating that itis 5 operative If the base on which itis registered finds within its reach the LED of INRANGE will begin to blink and the audio will be opened Atthis moment yot can begin to use your beltpack ALTAIR WBP 200 HEADSET CONNECTION A TINY Q G type connector allows to connecta headsetand a microphone to the beltpack The headset impedance must be of 200 Q or higher up to 2 and the microphone may be dynamic or electret type For the electret micro
13. he ON switch As a general rule charge the unit before using the system 4 SPECIAL OPERATIONS In order to set up some ofthe wireless beltpack possibilities the unit must be opened removing the two external screws of its rear panel NOTE This type of operations takes place with the unitis opened the best thing should be to carry it out a qualified technician Care must be taken to avoid short circuit between battery holders etc DANGER Before opening the unit tum it off Use of protective glasses when operating batteries CAUTION Protect the wireless beltpack from the rain and moisture mostly if it is open If liquid is spilled into the unit disconnect it from the mains and consulta qualified service technician WBP 200 SINGLE CHANN EL WIRELESS BELTPACK 9 ACTIVATING THE MICROPHONE PHANTOM POWER E EN The microphone PHANTOM power could be activated or disabled with an EG de internal jumper 2 PHANTOM With this jumper removed the phantom power is disabled and with this jumper placed the phantom power is activated EB of es If an electret microphone is used the PHANTOM power must be enabled and if a dynamic microphone is used the PHANTOM power must be disabled mr D The microphone PHANTOM power is 9 VDC 4 Itis convenient to place jumper over one pin for future use amp CANCELLING THE BUZZER The buzzer can be disabled definitely by removing
14. o register itin base 2 switches If everything o Dus goes well the base station base will sound if the buzzer it is turned on and the beltpack also if the buzzer itis turned on the correnpoding base station IN RANGE led will turn on and the beltpack IN RANGE led begin to blink If the procedure fails turn off the base station and the beltpack and start again BELTPACK DEREGISTRATION With the base station turned on and the beltpack that is wanted to deregister turned off turn on the beltpack pressing the ON OFF switch maintaining pressed the MIC ON OFF and the BUZZER ON OFF switches The beltpack will start normally but when it is connected to the base station this one will be reset and the beltpack will be deregistered DC IN CONNECTOR The three NiMh AAA 900 mA h batteries of the wireless beltpack must be charged with the ALTAIR charger by the DC IN connector The polarity is tip positive Charging time is three hours with the batteries empty After this 2 3 hours time the charger sets to trikle maintenance mode and can be left alone in the charger For a full charge it is recommended a 2 hours minimum charging in this state The estimated battery life in full duplex mode is 10 hours and 50 hours in standby mode with full charged batteries The included NiMh batteries has a shelf discharging time around 2 month So itis imperative to check the battery status before use switch ON the unitand then press shortly t
15. phone type is necessary to enable the phantom power of 9 VDC with an internal preset In order to obtain more information consult the special operation section The next list shows the XLR pins correspondence HEADSET N PN1 0 V MICROPHONE 2 0 V HEADPHONES PN3 PN4 SINAL HEADPHONES NOTE Headphones could be with a double or single muff In case of using a double muff headphone the two speakers should be wired in parallel mode CALL SWITCH When this switch is pressed a call signal is sentto the system and to the intercom channel in 4 CALL which itis connected the base station The call signal makes the LED associated with the switch to start blinking if the buzzer is enabled see buzzer on off section for more information an intermittent sound takes place during about three seconds the same as in all the units wireless beltpacks beltpacks base stations desk stations master stations etc connected to the same intercom channel The IN RANGE led of the base station correspondent to the register number of the beltpack will be blink In the wireless beltpacks will be turn on the associated led with the wireless beltpack that it is calling LOW BAT 1 BUZZ ON OFF 2 MIC ON OFF 3 IN RANGE 4 If the call is generated by the base station all associated led will be turn off If the CALL switch is pressed continuously the duration of the call signal will b
16. s the BUZZER ON OFF 4 Switch and o 4 atthe same time the UP or DOWN VOLUME switch Qu the sidetone gainitis adjusted the four leds ofthe beltpack to indicate UW the sidetone gain There are 10 steps of volume the LOW BATTERY led indicates o 1 the first step the BUZZ ON OFF led indicates the fourth step the MIC ON OFF led indicates the seventh step and the IN RANGE led the tenth step of the mic gain The SIDETONE GAIN itis stored in the unit BELTPACK REGISTRATION Each beltpack can be registered in two different base stations so that if it loses the range of one changes the operation to the other base station Each base station can register a maximum of four beltpacks See the WBS 200 owners manual for details Re WBP 200 SINGLE CHANN EL WIRELESS BELTPACK 8 With the base station turned on press and hold the REGISTER base station switch during six seconds At this moment the base station will sound if the buzzer itis turned on and will blink the IN RANGE 1 2 3 4 leds corresponding where is going away to register the new beltpack If we do notdo anything during 60 seconds the function will be reset If we pressed key REGISTER again the function will be reset With the beltpack that we want tto register turned off turn on pressing the ON OFF f switch maintaining pressed the VOLUME UP DOWN 4 to register it in E base 1 switches or maintaining pressed the VOLUME LIS UP DOWN and the 5 BUZZER ON OFF t

Download Pdf Manuals

image

Related Search

Related Contents

Manuel - Datatail  Moog Videolarm PurgeDome  Gas Cooktop  納入説明事項書  バッテリーフリーワイヤレスマウス 取扱説明書  

Copyright © All rights reserved.
Failed to retrieve file