Plogg – the Smart Energy meter Plug Terminal Software User Guide
Contents
1. settings if both the Ram settings are found to be corrupted as well as the backup copy in EEPROM If the Ram settings are corrupted but the EEPROM is intact then all logging values and unit settings will be retained but the accumulative KVAR and KWh values will reset back to O On the device powering up the unit up time will be reset to 0 Commercial in Confidence Page 18 of 182. AR 27 21 18 HHH0 HH04 1988 2208 valid m 3 from 3 87 898 Timers are enabled Current Time 2007 MAR 27 21 18 HaH0 HH88 19788 22808 valid HHH H8H 478 87 8 Timer A from from from from Above you can see that the timers are enabled the timer 1 is valid between 1900 2200 and the current time is 21 10 which indicates that timer 1 is valid Commercial in Confidence Page 15 of 18 energy OPTIMIZERS Enable Disable AC Timers se This command globally enabled or disabled the AC timers 0 3 se 0 1 s disabled Timers enabledt Set the RTC date RTD This command sets the RTD date rtd lt year 00 99 gt lt month 1 13 gt lt day 1 31 gt Commercial in Confidence Page 16 of 18 energy OPTIMIZERS Example BEE gt Ptda 03 26 The above example sets the date to 2007 March 26 Set the RTC time RTT This command sets the RTC time rtt lt hour gt lt minute gt lt second gt Example FET The above example sets the time to 21 35 00 Commercial in Confidence Page 17 of 18 energy OPTIMIZERS Masc device information Maximum Logged Values KHz and KVArh used for logging will support values up to 4294967 296Kwh after this they will wrap back to OKhw Unit up time will wrap after 497 days RTC values are supported up to the year 2063 Current wattage and reactive power is supported up to 3515Kw KVar Unit startup The unit will reset all
3. R This command also shows the maximum number of items that can be logged calculated by the remaining storage space and the number of items being logged Select logged values sln Use this command to select items to be logged available items are 0 Time Entry as date format from the RTC support is from 2000 to 2063 1 Last seconds wattage usage 2 Cumulative wattage usage since user reset or unit initialisation 3 Frequency hz of last seconds monitored value 4 RMS voltage of last seconds monitored value 5 RMS current of last seconds monitored value 6 Unit on time will wrap at 497 days shown in seconds since CPU reset 7 Reactive power of last seconds monitored value 8 Cumulative reactive power since user reset or unit initialisation 9 Phase angle V I in degrees of last seconds monitored value Run this command without any parameters to print out the items currently being logged sln lt list of items to be logged 0 9 gt Commercial in Confidence Page 11 of 18 energy OPTIMIZERS Example Zigbee Plope Terminal exe om no Current Log values H Time entry i Watts 2 Cumulative Watts 3 Frequency 4 RMS Voltage 5S RMS Current 6 Unit on time Fa g 7 amp gt Reactive Power Cumulative Reative Power Phase Angle UZI learing old log values as logging values have changed Each log entry is 32 bits in size therefore reducing the number of l
4. T 44 0 1472 266731 F 44 0 1472 360112 info energyoptimizers co uk www energyoptimizers co uk energy OPTIMIZERS Plogg the Smart Energy meter Plug Terminal Software User Guide Commercial in Confidence Copyright This document contains proprietary information that 1s protected by copyright This document must not be reproduced transcribed stored translated or transmitted in part or in whole without the prior written approval of Energy Optimizers Ltd and Diglis Design Limited ENERGY OPTIMIZERS LIMITED Registered Office ESTATE ROAD 1 SOUTH HUMBERSIDE INDUSTRIAL ESTATE GRIMSBY DN31 2TA UK Registered in England Reg No 5367780 energy _ OPTIMIZERS Introduction This document serves as a guide to operating the Plogg power meter products These are electrical power metering and logging products aimed at the appliance level This document describes the main software features that can be configured using the CLI Command Line Interface on the Plogg product using any of the three communication modes Bluetooth Zigbee or RS232 direct serial connection The CLI supports many additional test features these features are not described in this document and are not intended to be used by the end user and use of any features not described in this document may result in data loss and or damage to the device Communication Modes There are three methods of communication with the Plogg module these are RS232 Ser
5. ation may continue sending receiving information to the device without a rescan of the network To scan for devices press Escape when running the terminal in Zigbee mode if any devices are found these will be printed out to the user with a corresponding number against then to connect to a particular device press the function keys F1 F12 corresponding to devices 1 12 figbee Plogs Terminal exe Terminal in 4ighee mode 219260 no Flow control Press Escape to list devices Searching for device Device 1 G00d6 O0008aacda gt Found Searching completed 1 devices found Commercial in Confidence Page 4 of 18 energy OPTIMIZERS PloggTerminal Bluetooth When running in this mode the user must scan for nearby Bluetooth devices if any are found the user can then select a device to then communicate with note in this mode all Bluetooth capable devices will be lists with their BT network address along with their Friendly name if available Bluetooth Plogg Terminal exe Terminal in Bluetooth mode Press Escape to list devices searching Fi Device SPU C550 A613 f def HOS98828 gt Searching completed 1 devices foun Commercial in Confidence Page 5 of 18 energy OPTIMIZERS CLI functions The CLI interface is used to configure the Plogg device the commands that are available are Command Description Print help Repeat last command Show Meter Setup Commands s Set logging interval S
6. et AC ON OFF timers Enable Disable AC timers Real Time Clock controls RTDy m d Set the year month and day of the RTC ee PRTDy md Print Help This command prints the main CLI help page Repeat Last Command This command repeats the last command sent Show Meter Setup Commands s This command shows all the meter setup commands Commercial in Confidence Page 6 of 18 energy OPTIMIZERS Set Tariff cost ss This command set the tariff cost for tariffs 0 and 1 without any parameters the current settings are printed ss lt tariff 0 1 gt lt cost in pence per Kwh gt Example Zigbee PlopeTerminal exe H pence Kwh 4H pence Kwh 123 pence Kwh H pence Euh 123 pence Kwh 321 pence Kwh Set Tariff Times st This command sets when the tariff time for tariff O 1s valid when this tariff is not valid tariff 1 1s assumed When no parameters are given the current settings current time and currently tariff zone are printed st lt start time for tariff 0 gt lt end time for tarrif 0 gt Commercial in Confidence Page 7 of 18 energy OPTIMIZERS Example Zigbee PlopeTerminal exe rst Tariff from HHAR HHAA Current Time 2023 MAR 27 19 23 42 Current tarrif zone 5 rst 2Z HH HTHR 248 8788 2623 MAR 27 19 23 52 1 Set Logging interval si This command sets the time between logging events This time is specified in minutes when no parameters are specif
7. ial Direct cable connection Bluetooth Zigbee For all of these modes of communication the PloggTerminal exe can be used This application should be launched with one of the following command line parameters RS232 Serial PloggTerminal s lt serial port number gt Bluetooth PloggTerminal b Zigbee PloggTerminal z lt serial port number gt Where lt serial port number gt is the COM port number on the PC side Commercial in Confidence Page 2 of 18 energy OPTIMIZERS PloggTerminal RS232 Serial Mode When running directly connected with a serial cable the terminal will output all commands directly to the PC and all keyboard input is sent directly to the device This mode is the most reliable and ensures that the connection will be not be lost due to signal or interference 5 BEE Terminal in serial mode 9600 xon xoff Flow control PloggTerminal Zigbee When running in this mode the user must scan for nearby Zigbee devices if any are found the user can then select a device to then communicate with BEE Terminal in Zigbee mode 219260 no flow control Press Escape to list devices Commercial in Confidence Page 3 of 18 energy OPTIMIZERS When using this transport communication commands between the PC and the Plogg device are not guaranteed If the signal to the device is lost then commands to from the meter device may not be executed if the signal is regained the terminal applic
8. ied the current settings are printed Logging interval is set in minutes from minute up to 45 days 65535 minutes Note that if the logging interval is changes all currently stored logs are erased si lt logging interval in minutes gt Commercial in Confidence Page 8 of 18 energy OPTIMIZERS Example YS1 Logging interval is 1 minutets gt gt si1 36 Logging interval is 3600 minutets gt gt Print Accumulative Costs sc This command prints and optionally resets the accumulative costs sc lt l reset gt pag b 25YkUh H BHAkUHh 6 95YkWh Cost 8 55 H BHHAkUh Cost 4 44 accumulated costs 8 866kWh Gost 4 66 8 688kWh Cost 4 68 Commercial in Confidence Page 9 of 18 energy OPTIMIZERS Reset KW KVar Accumulators sr This command resets KW K Var Accumulators to zero ST Ewuh and KWar resett Print logged values sd This command prints and optionally resets all logged values sd lt l reset gt Commercial in Confidence Page 10 of 18 energy OPTIMIZERS Example figbee Plogs Terminal exe gt sd Printing logged values contains 1 of 13 gt entries entry LhAb entry Apt entry lLhAb 2023 MAR 27 19 32 14 7 200 U 48 888 kWh 54 z pa Time entry Watts Cumulative Watts entry LAB entry AAt entry LAB RMS Woltage RMS Current Unit on time Reactive Power entry 00A Frequency entry AB8 14 480 WA
9. ogging values will increase the number of log entries that can be created Log entries are wrapped currently when no free space is available for logging this means old values will be lost to store new data Changing the values that are stored in each log 1 e adding frequency will erase all old log values Delete old log entries sx Delete old log entries without printing SX Commercial in Confidence Page 12 of 18 energy OPTIMIZERS Example ec Zigbee Plope Terminal exe SK Clearing old log values gt Print out max values sm This command prints out max values for RMS Voltage RMS Current Wattage Along with a time entry for each if any are unavailable i e there haven t been any reported values yet then this information is reported sm lt l reset gt Commercial in Confidence Page 13 of 18 energy OPTIMIZERS Example 5 BEE gt am Highest RME voltage was 242 242 U at 2681 JAN 81 82 51 04 Highest RMS current was 4 939 A at 2601 JAM Ai 02 29 26 wattage was 1177 208 W at 2661 JAN i 82229226 RHS voltage was 242 242 U at 2661 JAN Ai 62 31 04 RMS current was 4 939 A at 2661 JAW i 82 29 26 wattage was 1177 206 W at 2061 JAN i 82 29 26 Resetting max voltages current wattage values m Highest RME voltage was 238 644 U at 2023 MAR 27 19 38 52 Highest RMS current was 6 116 A at 2023 MAR 27 19 38 52 Highest wattage was 7 2068 W at 2023 MAR 27 19 38 52 Print out val
10. ues at the current time sv Print out all values as of this instant in time SV Example 5 nag 260 MAR 27 19 48 59 200 H Cumulative Watts 8 661 kWh Frequency RMS Voltage RMS Current H days HH 26 08 14 466 UAR H 6H2 KUARh 363 Degrees Phase Angle U T gt gt Commercial in Confidence Page 14 of 18 energy OPTIMIZERS Set On Off AC Timers so This command set the times for the 4 AC ON OFF timers in the system Each timer has an on and an off time these can be wrapped around midnight 1 e 23 00 gt 02 00 Timers can be globally disabled in this case the AC power will be continuously on see the se command If the timers are enabled and there are valid timer values 1 e at least one time is not set to 00 00 to 00 00 then the system will turn on the AC power when the RTC is within any of the timers 0 3 that are found if the RTC lies outside of all the timers the AC power will be turned off Timers can overlap 1 e timer 0 12 30 gt 18 00 timer 1 16 00 gt 20 00 this will result in the AC power being on between 12 30 and 20 00 Without any parameters the times are printed out along with information detailing if the timers are enabled or not and if any of the timer zones are on so lt timer 0 3 gt lt time on gt lt time off gt Example ec figbee Plogs Terminal exe gt So Enter lt timer group 6 3 gt lt on time HHMM lt off time HHMM gt Timers are enabled 2007 M
Download Pdf Manuals
Related Search