OPERATING INSTRUCTIONS
Contents
1. GB70 85 GB308 84 T82008 4 21 QB67 85 BALL 3 0000 SCREW O RING _ SPRING SPRING BASE U WASHER 35506500 O RING TOP CUP BASE PLATE WASHER CYLINDER 35503450 BOWL WASHER PISTON ROD FILTER OIL TUBE WASHER BALL 6 0000 PRESSING PLATE SCREW M5X62. 502 5 LEFT WALL PLATE ASSEMBLY 1 a 31 T83502 2 LINKING SHAFT 42 GBSSY9 87 WASHER E 2 GB559 87 WASHER 18 33 G86170 86 NUT M8 2 OLZIG 4 TORSION SPRING l 34 GB859 57 WASHER f6 rg QLZ3 2 1a HANDLE SOCKET 1 35 GB6172 86 NUT M16 a GEES A GEAR SHAFT l 36 QLZ 20 5 REAR WHEEL ASSEMBLY 2 GBS1 86 COTTER PIN2 gt X 16 1 37 QLZ2e 2a LEFT BOLT l QLZ20 3 3a GEAR 38 GB6170 86 NUT MI 2 93 87_ WASHER 10 39 GB859 87 WASHER 12 2 e G i QG EE wg sa ba REPAIR PARTS LIST POWER UNIT ASSEMBLY QLZ3 4 8 LA 23 4 6 QLZ 2c 6 19 T83502 3 1 OLZ 2A 6 10a GLZZE 6 16a QLZ2A 6 11 BALL 9 0000 GB308 84 GB308 84 GB93 87 QLZ2c 6 3a GLZZA 6 6 QLZ 2 6 5 OLZ2A 6 20 QLZZA 6 7 QLZZA 6 2 GB308 84 OLZ3 4 9a PLUNGER BACK UP RING GB6172 86 GB3452 1 82 OLZ2e 6 4 O RING BASE PLATE PLUG SCREW WASHER SPRING BALL e 0000 TANK NUT Mio WASHER 10 WINDING GEAR WHEEL RELEASE VALVE SHAFT 26501500 RELEASE VALVE NUT RELEASE VALVE WICK STEEL WASHER SQUARE WASHER ALUMINUM WASHER BALL 6 0000 PLUG SCREW IGB3452 1 83 OLZ3 4 10 QLZI 4 11 GEB308 84 GLZ2A 6 18 OIL PLUG RESERVOIR QYL8 29 QLZ20 6 9 GB3452 1 82 GB345Z 1 82 OLZ3 4 3 32 QLZ3 4 15 QYL8 18 QLZ3 4 4 OLZ3 4 12 OLZ2c 6 17a
3. AND LINKAGE Use light oil on all moving and pivoting parts S HANDLE SOCKET PIVOT BOLTS Use light ol to lubricate pivot boits 6 PLUNGER AND PLUNGER PIN Use grease to lubricate connection between pump plunger and pin in handle socket HOW TO OPERATE THE FOOT PLATE Close the release valve clockwise Move the jack under the load Please push the foot plate with hand and or foot until the saddie touches the load Continue to operate the jack with handle gt Operating Instructions and Parts List 3 TON CAPACITY SERVICE JACK CAUTION THIS JACK IS DESIGNED FOR LIFTING PURPOSES ONLY AFTER JACKING ALWAYS SAFETY STANDS TO SUPPORT LOAD BEFORE MAKING REPAIRS FOR YOUR SAFETY DO NOT OVERLOAD BEYOND RATED CAPACITY REPAIR PARTS LIST SPARES NAME ITEMI CODE NAME NUT Min CYLINDER ASSEMBLY WE RESERVE THE RIGHT TO ALTER DESIGNS AND SPECIFICATIONS AT ANY TIME WITHOUT PRIOR NOTICE l 20 GB6172 86 QLZ2A 20 RETURN SPRING 2 QLZ ZA 29 21 LOWER HANDLE l GB84 1 86 RETAINING RING 30 2 22 GB5780 86 SCREW M amp X 35 l GB91 86 COTTER PIN 4x40 1 9 41 226 2 3 UPPER HANDLE i QLZ3 1 5 LINKING BLOCK 1 QLZZC la HANDLE SOCKET SCREW i T83502 4 FOOT PLATE ASSEMBLY 1 25 01726 2 HANDLE SOCKET PIN 1 T83502 6 SADDLE ASSEMBLY l ae pee ke En KEE ed Ell EE rr e l a E GB70 85 SCREW M12x25 2 eg ayen Bac A 30 T83
4. OPERATING INSTRUCTIONS IMPORTANT Sometimes during shipment and handing air gets Into the hydraulic system causing poor lifting performance Purge any air from the system by fully opening Release Vaive turn handle counterclockwise as shown then while holding the saddle down operate pump handle rapidly several times TO RAISE JACK 1 Turn the operating handle clockwise until release valve closes Do not over tighten the valve 2 Place jack directly under object to be lifted so that saddle takes up weight firmly and centrally Check positioning under slight load to make sure jack will not slip when in use 3 Raise jack to required height After lifting use jack stand to hold load for any length of time TO LOWER JACK slowly turn the operating handle counter clockwise The speed of lowering is controlled by the amount valve is opened LUBRICATION POINTS Before operating the jack lubricate the points indicated in the diagram Use lubricants as indicated by the following numbers as marked on the diagram 1 HANDLE Use light oil on moving parts and lightly grease handle at point it fits into the handle socket 2 WHEELS Use light oil on axles and caster bearings TO OPERATE oner RELEASE VALVE d r Ce TO OPERATE OPEN JACK INSERT HANDLE END INTO HANDLE SOCKET AND PUMP JACK HANDLE TO RAISE LOAD CORRECT LOAD CONTACT 3 UFTING ARM Inject grease into grease fitting 4 SADDLE
Download Pdf Manuals
Related Search