TPP Pipettor Turbo-Fix Operating instructions
Contents
1. TPP Pipettor Turbo Fix device 1 rechargeable Li ion battery Mains adapter Wall mount Sterile filter spare Quick Start Guide 2 2 Overview of TPP Pipettor Turbo Fix 4 1 nin 3 2 3 T 4 1 39 2 6 Ys 7 Ta 7 b 8 C d ak e f 2 www tpp ch Aspiration button Dispensing button Thumb wheel to set maximum speed Battery charge indicator Socket for mains adapter cable Handle Nose piece Nose piece Stabifix fa 7b 1C 7d fe Tf O ring Nose piece housing upper part Filter rubber Sterile filter Pipette mount Nose piece housing lower part TPP Pipettor Turbo Fix Operating instructions V09 Installation 3 Installation 3 1 Charging the battery A full charge takes 3 5 hours Before the first use TPP Pipettor Turbo Fix should be charged until the battery charge indicator 4 turns green showing that the battery is full When the battery charge indicator 4 starts flashing red TPP Pipettor Turbo Fix can be used for around 100 pipetting cycles before shutting down It should thus be recharged immediately TPP Pipettor Turbo Fix has an integrated protection it will not overcharge even if it is connected to power for indefinite time To avoid unnecessary power consumption it is recommended to unplug the power supply when the charge indicator is green TPP Pipettor Turbo Fix can be used while it is being charged The battery charge indicator prov2. aqueous solutions with plastic or glass pipettes of 1 to 100 ml volumes It is intended for measurement control and laboratory use 1 2 Safety notes 1 Do not use or charge TPP Pipettor Turbo Fix in an atmosphere with danger of explosion Also do not pipette highly flammable liquids such as acetone or ether 2 When handling dangerous substances comply with the material safety data sheet MSDS and with all safety guidelines such as the use of protective clothing and safety goggles Never point a pipette in anyone s direction 3 Avoid pipetting of liquids whose vapours could attack the materials PA polyamide POM polyoxymethylene FPM fluor rubber NBR nitrile rubber CR chloroprene silicone Corrosive vapours could also damage metallic parts inside the device 4 Use an original TPP mains adapter only and protect it from moisture otherwise TPP Pipettor Turbo Fix might be damaged 5 Prolonged exposure of TPP Pipettor Turbo Fix to UV light can cause discolouration and or yellowing of the plastic housing However this will not affect the performance of the device in any way Regardless of the listed safety notes additionally applicable regulations and guidelines of trade associations health authorities trade supervisory offices etc must be observed Ao TPP Techno Plastic Products AG TPP Pipettor Turbo Fix Operating instructions V09 Description of the device 2 Description of the device 2 1 Scope of delivery
3. al speed www tpp ch T OV sjonpoJg onsejd ouuoe dd 4 3 Troubleshooting Problem Pipette drips leak in the system Reduced aspiration efficiency or no liquid aspiration Reduced operating time with fully charged battery Extremely long charging time of battery Extremely short charging and operating time Probable cause Pipette is damaged or not fully inserted in the nose piece 7 The inside of the pipette mount 7e is damaged resulting in insufficient sealing of the pipette neck The filter rubber 7c or the filter 7d in the nose piece are damaged or missing causing a leak The filter 7d is wet or dirty The nose piece 7 is not tight The battery is discharged battery charge indicator flashes red The battery is missing The battery is defective The battery is wrongly inserted The battery is worn Wrong battery type is inserted Wrong mains adapter is used Wrong battery type is inserted Remedy Reinsert a new pipette and push it all the way into the nose piece Make sure that the pipette mount orientation is correct see section 4 1 Replace the pipette mount Replace the filter rubber and or the filter Replace filter Tighten the nose piece or replace defective parts Charge the battery Insert the battery or connect the instrument to the mains adapter Replace the battery Insert correctly note polarity and Replace the battery Use only or
4. cated Running time at least 5500 cycles of aspiration and dispensing of 25 ml Input 100 240 VAC 50 60 Hz Output 17 VDC 10 180 mA 10 Housing PA Nose piece housing POM Pipette mount Silicone Filter rubber Silicone 125 x 130 x 35 mm 195 g Operation 5 40 C max 80 RH Storage 10 50 C max 95 RH complete set with filter 0 45 um unsterile for holding Pipettor Turbo Fix on the wall sterile sterile silicone to fix the pipette in the nose piece Stabifix silicone to fix the filter in the nose piece Stabifix Lithium polymer min 500 mAh transparent TPP yellow transparent TPP yellow Part No 94750 94 751 94752 94 753 94754 94755 94756 94 757 94 758 11
5. g 7f will disengage after about 1 8 of a turn Remove the pipette mount 76 the filter 7d and the filter rubber 7c if required It is recommended to change the hydrophobic filter 7d every three months Should the filter get wetted or soiled it has to be changed immediately The filter must be oriented with the colored side blue or red facing upwards towards TPP Pipettor Turbo Fix After maintenance work perform a leak test to ascertain correct functioning of TPP Pipettor Turbo Fix liquid should not leak out of a filled pipette before the dispensing button is pressed 5 2 Equipment disposal TPP Pipettor Turbo Fix device must not be disposed of with unsorted municipal waste Dispose of TPP Pipettor Turbo Fix in accordance with the laws and regulations m in your area governing disposal of devices 10 TPP Techno Plastic Products AG TPP Pipettor Turbo Fix Operating instructions V09 6 Technical data Pipetting speed Battery Mains adapter Materials Dimensions H x W x D Weight Ambient conditions 7 Spare parts Spare part Nose piece Stabifix 7 Wall mount Filter 0 45 um 7d Filter 0 22 um 7d Pipette mount 7e Filter rubber 7c Battery Li ion Battery compartment lid Housing 6 www tpp ch max 13 5 ml s with a 50 ml serological pipette Type rechargeable Li ion min 500 mAh Typical charging time 3 5 hours Technical data Charging cycles 500 1000 when charging as indi
6. ides various information Battery charge indicator Battery status and information Flashes red Battery is low Charging is needed Is red and power supply is connected Battery is being charged Is green and power supply is connected Battery is fully charged Flashes alternately red and green Battery error Check if the correct type of battery with correct polarity and or power supply are used 3 2 Replacing the battery a 1 Move the lid of the battery compartment upwards and remove it a S 2 Replace the old battery with an original TPP y rechargeable battery Li ion min 500 mAh and make sure that it is inserted with the correct polarity a 3 Close the battery compartment with the lid a 3 3 Mounting of the wall mount The wall mount serves to park TPP Pipettor Turbo Fix To mount the wall mount remove the protective foil from the adhesive tape at the back of the holder Hold it with the sign lt up gt facing upwards and press it to the desired place Make sure that the surface onto which the wall mount is mounted is smooth clean and grease free Wait 24 hours before using the wall mount for the first time Alternatively the wall mount can be fixed with the included screws 6 TPP Techno Plastic Products AG TPP Pipettor Turbo Fix Operating instructions V09 Operation 4 Operation 4 1 Inserting the pipette b The silicone pipette mount 7e has a special conical channel to guarantee a firm and leak p
7. iginal Li ion battery 94756 Use only original mains adapter Use only original Li ion battery 94756 60A suononujsui Gune4edo xi4 oqun Jonedigd ddl uoneJedo yo ddi MMM Problem Battery is not charging Battery operation not possible Probable cause The battery is wrongly inserted Wrong battery type is inserted Wrong mains adapter is used The battery is wrongly inserted Wrong battery type is inserted The battery is missing Remedy Insert correctly note polarity and Use only original Li ion battery 94756 Use only original mains adapter see chapter 6 Insert correctly note polarity and Use only original Li ion battery 94 756 Insert the battery 60A suononsysul Bunesedo x j oq n Jonedigd ddl uoneJedo TPP Pipettor Turbo Fix Operating instructions VO9 Maintenance 5 Maintenance 5 1 Cleaning and servicing TPP Pipettor Turbo Fix can be cleaned with a cloth moistened with soapy water or with a 70 ethanol Never use acetone or other solvents The nose piece housing 7 b 7f the pipette mount 7e and the filter rubber 7c can be autoclaved at 121 C Disassembly of the nose piece Unscrew the nose piece 7 from the handle by turning it counter clockwise Hold the upper part of nose piece housing 7 b press the lower part 7f firmly against the Came upper part 7b and turn it counter clockwise left The lower part of nose piece housin
8. li TPP Pipettor Turbo Fix Operating instructions 155923 V09 D claration de conformit Declaracion de conformidad Declaration of conformity Konformitatserklarung Dichiarazione di conformit TPP Techno Plastic Products AG 8219 Trasadingen Switzerland declares on its own responsibility that the product erklart in alleiniger Verantwortung dass das Produkt d clare sous sa responsabilit exclusive que le produit declara bajo su propia responsabilidad que el producto dichiara sotto la propria responsabilit che il prodotto TPP Pipettor Turbo Fix in accordance with EC directives gem ss der EU Richtlinien est conforme au terme de la directives CE de acuerdo con las directivas CE in conformit alle direttive CE 2006 95 EC Low voltage equipment 2004 108 EC Electromagnetic compatibility 2011 65 EC Restriction of Hazardous Substances 2002 96 EC Waste Electrical and Electronic Equipment 2009 129 EC Eco Design Directive 2006 66 EC Battery Directive is in compliance with the following normative documents mit den folgenden normativen Dokumenten bereinstimmt aux documents normatifs ci apres cumple las documentos normativos soddisfa le normative seguenti EN 61010 1 Safety requirements for electrical equipment for measurement control and laboratory use General requirements EN 61326 1 Electrical equipment for measurement control and laboratory use EMC requireme
9. nts Standards for Canada and USA CAN CSA C22 2 Safety requirements for electrical equipment for measurement No 61010 1 control and laboratory use General requirements UL Std No 61010 1 Safety requirements for electrical equipment for measurement control and laboratory use General requirements FCC Part 15 Class A Emission Trasadingen October 25 2013 s po 4 Rolf Tanner Markus Stoll CEO Quality Manager TPP Pipettor Turbo Fix Operating instructions V09 Table of Contents NOOR WD gt Imprint 2015 TPP Techno Plastic Products AG Supplier TPP Techno Plastic Products AG CH 8219 Trasadingen Switzerland T 41 52 687 01 87 F 41 52 687 01 77 info tpp ch www tpp ch Customer service Please contact your local TPP Techno Plastic Products AG representative see www tpp ch or contact info tpp ch www tpp ch VTEC LOIN hiana UU Description of the CEVICE cccccceeccccseececeeececeaececeaeeeeeeueeeseeeeeseaeeesaaeeesseeesaaeees IT SLIA 1 F216 REL OODETGUOLI accu cam 1 nane kin e dicet QES SN e M K na d xan xe gana aM LU en den eee DER SONA SARA KE Wella e ome er TT TES CHM CGA scr vie etes E y LI D Se A cU be DD Spare PAN gt ante eee ete rec atta us tales essc een pL gwd TPP Pipettor Turbo Fix Operating instructions V09 Introduction 1 Introduction 1 1 Intended use TPP Pipettor Turbo Fix is a pipette controller designed for aspirating and dispensing
10. roof grip of the pipette independently of its diameter Disassemble the nose piece see 5 1 Cleaning and servicing on page 10 and orient the pipette mount a with the large opening facing down for pipettes gt 2 ml factory setting or b with the small opening facing down for pipettes lt 2 ml WARNING Do not insert pipettes with force into TPP Pipettor Turbo Fix because they can break and cause injury particularly thin pipettes made of glass 4 2 Pipetting Press the aspiration button 1 to fill the pipette and the dispensing button 2 to empty it The aspiration and dispensing speed can be controlled in two manners Fine speed adjustment by varying the finger pressure on the buttons 1 2 Step less presetting of the maximum pump speed by turning the thumb wheel 3 to optimally match the pipette capacity turning to the left slower pump speed for small pipettes to the right faster for large pipettes To empty the pipette by gravity force press the dispensing button only slightly in order to avoid reaching the trigger point where the pump starts running Gravity dispensing is used for to deliver TD pipettes that are not of the blow out type blow out pipettes have two thin rings or a frosted band around the neck TPP Pipettor Turbo Fix is featured with a TURBO mode Plug the mains adapter cable into the pipette controller and turn the thumb wheel completely to the right for maxim
Download Pdf Manuals
Related Search