CE User Manual
Contents
1. Source Fourmini CE User Manual Revision A Copyright O 2013 Electronic Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7063M1210 Rev A Released 2013 05 Table of Contents Source Four Mini CE Guidelines 1 IHEKOAUCHON 258 LELE Aa See LIAR a TE LA de 2 Basic ASSCMDIY las na au aeg 3 Install Lens Tube 22 222 22 6 8 node ee wan Nek en A 4 AUUSTINEMES Er Du ts kn a en dadas ll ala tt din th fas 4 Adjusting the yoke position 4 Setting the angle with the yoke ooo 4 Locking the rotation in the canopy and track mount variations 5 Focusing the beam 1 rennen 5 Shaping the Beam oi oo oo co co 8240525 ee eee ee 5 Pattern Projecti0N oooooocccoooccoo een 6 Colour Frame Holder 4 oo 4445 24232202424 6 Adjusting the C clamp on the Portable 7 Replacing the Lamp __ij iw iw ce eee ees 8 Cleaning the Glass Lens coooooo oo 9 ETC Eos Eos Ti Gio lon Element Emphasis Expression Insight Imagine Focus Express Unison Obsession II ETCNet2 EDMX Revolution and Sensort are either registered trademarks or trademarks of Electronic Theatre Controls Inc in the United States and other countries ETC permits the reproduction of materials in this manual only for non commercial purposes All other rights are reserved by ETC ETC intends2. Pipe bolt Yoke bolt j Il The C clamp attaches the luminaire to the mounting pipe and allows you to adjust the position of the luminaire once itis mounted The C clamp will fit a 9 525 mm to 2 54 cm pipe Step 1 Tightly fasten the C clamp to the yoke with the provided yoke bolt and lock washer Step 2 Place the C clamp on the mounting pipe and then tighten the pipe bolt to secure it Step 3 Loosen the C clamp yoke bolt and rotate the yoke to the desired position Step 4 Tighten the bolt to lock the luminaire CAUTION Tighten the C clamp pipe bolt to about 2 N m Approximately finger tight plus up to one quarter turn Do not use excessive force Note The Source Four Mini yoke has a C clamp hole for an M10 bolt Replacing the Lamp Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Lamp housing Lamp housing knob Disconnect power to the Source Four Mini before installing the lamp Loosen the brass lamp housing knob on the back of the lamp housing The knob is not captured so it may come loose from the luminaire Pull the lamp housing away from the luminaire body Pull on the lamp carefully to remove it from the lamp housing Gently push down on the replacement lamp until it is seated in place Realign the housing into the grooves of the luminaire Align the knob with the hole and tighten the
3. this document whether printed or electronic to be provided in its entirety C DECLARATION OF CONFORMITY Unit 26 28 Victoria Industrial Estate Victoria Road s Re London W3 6UU We Electronic Theatre Controls Limited Tel 44 0 20 8896 1000 Fax 44 0 20 8896 2000 www etcconnect com declare under sole responsibility that the product Product name Source Four Mini luminaire Product type model Source Four Mini Canopy mount Source Four Mini Track mount amp Source Four Mini Clamp mount Versions fitted with tungsten lamp Item numbers One sample of each type to which this declaration relates is in conformity with the following Standards EN 60598 1 2008 Luminaires General requirements and tests EN 60598 2 6 1995 Luminaires Particular requirements Luminaires with built in transformers for filament lamps EN 60598 2 17 1989 Luminaires Particular requirements Specification for luminaires for stage lighting television film and photographic studios outside and indoor following the provisions of EU LV Directive s 2006 95 EC EN 55015 2006 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EN 61547 2009 Equipment for general lighting purposes EMC immunity requirements EN 61000 3 2 2006 Electromagnetic compatibility EMC Limits Limits for harmonic current emissions equipment input current up to and including 16 A per phase Class C
4. EN 61000 3 3 2008 Electromagnetic compatibility EMC Limits Limitation of voltage changes voltage fluctuations and flicker in public low voltage supply systems for equipment with rated current lt 16 A per phase and not subject to conditional connection following the provisions of EU EMC Directive s 2004 108 EC London United Kingdom Mr Adam Bennette Place of issue Name of authorised person 11th March 2013 la Benti Date of Issue signature of authorised person Printed 11 Mar 13 Page 1 Decl 117 Version A LON FILE2 Shares RND DofC Master declaration doc Electronic Theatre Controls Ltd Registered Office Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU Registered in England No 3057796 VAT No GB 662 9487 90 m D As m n D un SHIIYAWH Source Four Mini CE Guidelines Read the entire User Manual before using the equipment WARNING Please note the following safety precautions Do not mount the Source Four Mini CE on or near a flammable surface The Source Four Mini CE is suitable for indoor use only with a maximum ambient temperature 40 C Maximum exterior surface temperature 125 C Relative humidity 90 maximum non condensing If the external cable is damaged it shall be replaced by ETC or our service agents Always hang the Source Four Mini CE with the colour frame held securely behind the retaining clip Always replace the lamp if it
5. UU UK m Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome IT m Via Pieve Torina 48 00156 Rome Italy Tel 39 06 32 111 683 m Fax 44 0 20 8752 8486 Holzkirchen DE m Ohmstrasse 3 83607 Holzkirchen Germany m Tel 49 80 24 47 00 0 m Fax 49 80 24 47 00 3 00 Hong Kong m Rm 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong m Tel 852 2799 1220 Service Americas service etcconnect com m UK a tel m DE techserv hoki etcconnect com M Asia service etcasia com Web www etcconnect com M Copyright 2013 ETC All Rights Reserved MM Product information and specifications subject to change 7063M1210 M Rev A M Released 2013 05 M ETC intends this document to be provided in its entirety
6. becomes damaged or thermally deformed Disconnect the unit from power before all cleaning and maintenance Keep the luminaire at least 3cm away from any lit surface Lighted objects at this distance or greater will not exceed 90 C temperature from projected light Introduction The Source Four Mini has four field angle choices and comes in a portable version with a miniature C clamp and yoke mounted transformer a canopy mount design with an integral transformer and a track mount design with an integral transformer Surprisingly bright for its size the Mini offers crystal clear image projection and a bright even field Portable Canopy Track There are three versions of the Source Four Mini This manual covers common features for all versions For information on installing the canopy and track mount variations see the Source Four Mini Canopy and Track Mount Kits Installation Guide For information on adjusting the miniature C clamp on the portable variation see Adjusting the C clamp on the Portable on page 7 WARNING Please note the following safety warnings before use Do not mount the luminaire on or near combustible surfaces Always hang the luminaire with the colour frame retaining clip in the locked position WARNING Track Mount Version To reduce the risk of fire and electric shock use only with EUTRAC track system Note Track Mount Version For best results with 230v it is recommended that r
7. ep 1 Use a Phillips screwdriver to loosen the screw on the slot cover Do not remove the screw Step 2 Slide the cover completely forward to 2 54cm Diameter expose the slot o Step 3 Insert the pattern holder Step 4 Slide the slot cover back toward the shutters until it meets the pattern handle Leave enough space to move the handle Step 5 Secure the slot cover by tightening the screw Shown at actual size Colour Frame Holder The Source Four Mini comes equipped with a 2 54 or 70mm colour frame which is a metal frame used to hold colour media often referred to as gel in front of the lens The colour frame holder is eguipped with a retaining clip that prevents the colour frame from falling out WARNING Make sure the colour frame is locked in position with the TT retaining clip Note The colour frame should be inserted open side down Step 1 Release the retaining clip by gentl Retainin i pushing it up pa eer ape gt Step 2 Insert the colour frame Ii Step 3 Lock the retaining clip by gently pushing it down Colour Additional accessories are available for the Mini that Frame also fit into the colour frame holder Those Holder accessories are top hat short top hat half hat short half hat and donut When an accessory is used the colour frame should be installed in the rear slot of the holder 6 Source Four Mini User Manual Adjusting the C clamp on the Portable
8. everse phase dimming be used 2 Source Four Mini User Manual Basic Assembly Yoke Pattern Lamp housing Holder Slot Lamp housing gt 4 knob Lens tube Shutter Barrel Colour frame N z retainer clip lt S da Shutters x4 INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS Lighted lamp is HOT WARNING To reduce the risk of FIRE ELECTRIC SHOCK EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS 1 Turn off unplug and allow to cool before replacing lamp 2 Lamp gets HOT quickly Only contact switch plug when turning on 3 Do not touch hot lens guard or enclosure 5 Do not use in proximity to normally flammable materials 6 Use only with a lamp rated at 50W or less SAVE THESE INSTRUCTIONS Install Lens Tube A lens tube must be installed prior to use of the Source Four Mini There are four lens tube sizes available 19 26 36 and 50 Beam focus knob Step 1 Unscrew the beam focus knob from the loose lens tube Step2 Slide the lens tube into the shutter barrel Step 3 Install the beam focus knob Adjustments Adjusting the yoke position The Source Four Mini provides multi positioning capabilities within its yoke for overall luminaire angle Setting the angle with the yoke Yoke locking knob Step 1 Loosen the yoke
9. lamp housing knob Cer Se WARNING Allow the lamp housing to cool before replacing the lamp CAUTION RISK OF FIRE Use an MR16 lamp rated at 50 Watts or less CAUTION DRY LOCATIONS ONLY Note It is recommended to use an MR16 lamp with a nominal beam angle of 38 degrees Source Four Mini User Manual Cleaning the Glass Lens WARNING Do not use ammonia based or other harsh commercial cleaners Clean lens only as directed Commercially available glass cleaning agents should be avoided as they may contain ammonia other harsh chemical detergents or abrasive agents These cleaners may damage the glass surface and the Anti Reflective coatings Do not immerse or soak the glass in any cleaning solution Step 1 Step 2 Step 3 Step 4 Step 5 Remove the beam focus knob from the barrel Remove the lens tube from the barrel Remove dust with a blast of oil free air or wipe with a clean lint free cloth Isopropyl alcohol distilled water or a 50 50 mixture of each can be used to clean the glass surface Slide the lens tube back into the barrel with the colour frame retainer clip on the top Reinstall the beam focus knob 10 Source Four Mini User Manual Corporate Headquarters m 3031 Pleasant View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA m Tel 608 831 4116 m Fax 608 836 1736 London UK m Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6
10. locking knob Do not remove the knob Step 2 Tilt the luminaire to the desired position Step 3 Tighten the yoke locking knob to secure position 4 Source Four Mini User Manual Locking the rotation in the canopy and track mount variations Step 1 Rotate the luminaire into the desired position Luminaire will be prevented from rotating completely around to protect the wiring Step 2 Insert a 1 5mm Allen wrench into the small hole on the yoke lock Step 3 Turn wrench to tighten down the yoke lock Focusing the beam Step 1 Loosen the beam focus knob located under the barrel Do not remove the knob Step 2 Slide the lens tube forward or backward to achieve the desired beam edge Step 3 Once the luminaire is focused tighten the beam focus knob Shaping the Beam The beam can be shaped using the four shutters or with a pattern The Source Four Mini has four shutters left right top and bottom Each shutter can be pulled out or pushed in to create the desired beam shape Beam focus knob a Pattern Projection The Source Four Mini has a pattern holder slot on the top side of the shutter barrel in front of the shutter It accommodates a E size pattern holder Use an optional donut in the colour frame holder to enhance pattern projection When the slotis not in use a small sheet metal cover secured with a Phillips screw prevents light leakage St
Download Pdf Manuals
Related Search