MICRON USER GUIDE
Contents
1. Switching On Off e Push down and release the power switch to activate the unit e Push up and release the power switch to deactivate the unit LED will briefly flash red Power Off Please note The unit does not beep when switched on or off Power On Multi Colour LED This allows the choice of five colours Red Blue Green Cyan amp White to be selected with the push of a button 1 Simply remove the battery cover and screws 2 Using a pen or LED selector tool press the selector plunger positioned between the batteries to select the LED colour Your choice will remain stored in the Microns memory even when the batteries have been removed Buzzer Bar Locking Screw This allows infinite alignment adjustability for the Micron facing position If the Micron is not facing the desired position unscrew the micron until you can reach the locking screw Back the locking screw a quarter to half a turn then screw the Micron back on Controls Min Sensitivity Volume Control Turn the knob clockwise to increase volume anti clockwise to lower volume There are eight different volume settings available Max Sensitivity Tone Control Turn the knob clockwise to raise pitch anti clockwise to lower pitch There are eight different tone settings available Sensitivity Table Intelligent Sensitivity Control With See Saw Elimination Setting 1 68mm Min Turn the knob clockwise to increase the sensitivity and anti clockwise t2. changes to purple When this occurs batteries should be replaced at the earliest Jack Plug opportunity although the unit may continue to work for some time in this condition particularly if the volume setting is reduced No audible indication of low battery is given It is not possible to change the LED colour once it has changed to purple Jack Socket AN Warnings Do not trigger LED or speaker in close proximity to human or animal eyes and ears e Store this equipment out of reach of children and infants e Avoid dropping or subjecting the Micron to severe impacts Use only recommended batteries and accessories Warranty amp Product Registration Register your Fox product online at www foxint com You will be given a Customer Reference Number and a Warranty Reference Number please make a note of these numbers You can view warranty details online using the Customer Reference number Alternatively fill out the Warranty Card enclosed in the box and post to Customer Care Department Fox International Group Ltd UK Headquarters 56 58 Fowler Road Hainault Business Park Hainault Essex IG6 3UT Micron is a Registered Trade Mark NTX R NX N amp NTX Receiver are Registered Trade Marks We reserve the right to alter or modify the contents of this manual pd
3. o reduce the sesitivity Setting 2 60mm There are eight different sensitivity settings available In all sensitivity settings except maximum the line must setting a On travel the specified distance in the same direction in order to trigger the unit Any movement in the opposite ork i o direction will reset the distance counter to zero This can substantially reduce or eliminate false triggering caused Setting 6 26mm by wind and water movement The unit automatically defaults to maximum sensitivity once the sensitivity f Setting 7 17mm threshold has been reached i e once the rollerwheel is moving Setting 8 8 5mm Max Sockets Drying Out After Use in Heavy Rain fe Extension Socket Extension socket for wired extension boxes or remote system These Microns have been designed to be weatherproof However after use in heavy rain it is important to allow the unit to dry out properly by bringing the Power Out Socket unit indoors and removing the hard case cover O New 3 5mm power out socket designed for use with Fox next generation Swingers and Hangers with Colour Sync To use with Fox Illuminated Swingers and Hangers that use a 2 5mm jack plug the supplied adaptor AN NEVER place batteries in a hot environment e g on a radiator will need to be used 3 5mm 2 5mm Adaptor For use with Illuminated Hangers and Swingers Low Battery Warning When the Micron detects that its batteries are failing the main LED colour
4. www foxint com FOX MICRON USER GUIDE ENGLISH NX e See Saw Effect Elimination Feature e Audible amp Visual Backdrop Indication e Weatherproof Sealed Case e Digital Circuitry e Low Battery Drain e CNC Machined Rollerwheel Tru Run Features Multi Colour LED Micro Light Slots D Tec Sensing System On Off Volume Control Battery Cover High Quality Cone Speaker Tone Control Intelligent Sensitivity System Control Power Out Socket 3 5mm Extension Socket 2 5mm Buzzer Bar Locking Screw Rigid 3 8 Stainless Steel Thread Fitting the Batteries 1 Turn off unit prior to fitting or replacing batteries 2 Using the supplied screwdriver unscrew the two battery cover screws 3 Pull the lower tab up to remove the battery cover 4 Take care removing the batteries Insert new batteries and ensure correct polarity A 5 For best weatherproofing ensure battery cover has a good seal by firmly pushing the edging of the battery cover 6 Re fit cover and screws DO NOT over tighten the battery compartment screws excessive force will damage the screw threads Battery Requirements The Microns require 2 x LR6 AA 1 5V Alkaline batteries The use of good quality batteries is essential for maximum battery life To reduce the risk of battery leakage DO NOT mix old and new batteries AN DO NOT mix different battery types e The use of rechargeable batteries is NOT recommended
Download Pdf Manuals
Related Search