CopperLink™ Model 1214
Contents
1. down for OFF position Figure 7 DIP switch orientation Configuring DIP Switch S1 DIP switch S1 is where you configure the CopperLink line The following tables describe the configuration for the CL1214 Table 1 S1 Summary Position Description S1 1 Local Remote Configuration 1 2 Line Rate Symmetry 1 3 Line Rate Symmetry 1 4 Reserved 1 5 SNR Margin S1 6 Reserved S1 7 Reserved S1 8 Reserved Introduction 20 CopperLink 1214 User Manual 3 Configuration Switch S1 1 Local Remote Configuration Use switch S1 1 to configure the unit as Remote or Local in the CL1214 pair Table 2 Local Remote Unit Configuration ON CPE Remote OFF CO Local Switches S1 2 and S1 3 Symmetric Asymmetric Operation Use switches S1 2 and S1 3 to configure the CopperLink line rate type and operation Table 3 Symmetric Asymmetric Selection Chart OFF OFF High Speed Symmetric OFF ON High Speed Asymmetric ON OFF FastPath High Speed Asymmetric ON JON I Long Range Asymmetric Note See Line Rate amp Reach Chart Based on 24 AWG 0 5 mm on page 37 for line rate distances Switch S1 5 General Protection Signal to Noise Ratio Use switch S1 5 to configure line noise protection Table 4 Signal to Noise Ratio ON 6dB OFF 9dB 6dB Original line noise protection with 6dB S2. For devices with an external power adapter the power adapter shall be a listed Limited Power Source The mains outlet that is utilized to power the device shall be within 10 feet 3 meters of the device shall be easily accessible and protected by a circuit breaker in compli ance with local regulatory requirements For AC powered devices ensure that the power cable used meets all applicable standards for the country in which it is to be installed For AC powered devices which have 3 conductor power plugs L1 L2 amp GND or Hot Neutral amp Safety Protective Ground the wall outlet or socket must have an earth ground For DC powered devices ensure that the interconnecting cables are rated for proper voltage current anticipated temperature flammability and mechanical serviceability WAN LAN amp PSTN ports connections may have hazard ous voltages present regardless of whether the device is powered ON or OFF PSTN relates to interfaces such as telephone lines FXS FXO DSL xDSL T1 E1 ISDN Voice etc These are known as hazardous network volt ages and to avoid electric shock use caution when working near these ports When disconnecting cables for these ports detach the far end connection first Do not work on the device or connect or disconnect cables during periods of lightning activity In accordance with the requirements of council directive 2002 96 EC on Waste of Electrical and Electronic
3. Connecting the 10 100Base T Ethernet Interface on page 17 3 Connect the power plug refer to Connecting Power on page 18 CL1214 EUI Line RJ 45 CL1214 TB Line Terminal Block CL1214 BNC Line BNC Coaxial CL1214 S Line RJ 45 POTS Figure 2 CL1214 rear panel options Planning the Installation 15 CopperLink 1214 User Manual 2 Installation Connecting the Line Interface and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use The CL1214 supports communication between two peer Ethernet LAN sites over a distance of up to 10 000 ft 3 km over 24 AWG 0 5 mm twisted pair wire Cat5 or 75 ohm BNC Note Actual distance and link performance may vary depending on the environ ment and type gauge of wire used Follow the steps below to connect the CL1214 CopperLink Interfaces Note The CL1214 units work in pairs One of the units must be configured as a L Local unit and the other unit must be configured as a R Remote unit Connecting the Line Interface for CL1214 EUI or CL1214 TB 1 To function properly the two CL1214s must be connected together using twisted pair unconditioned dry metal wire between 19 0 9mm and 26 AWG 0 4mm Leased circuits that run through signal equalization equipment are not a
4. CopperLink Model 1214 High Speed Ethernet Extender User Manual Fn gd ES Ka p FEE SOON This is a Class A device and is not intended for use in a residential environment Sales Office 1 301 975 1000 Technical Support 1 301 975 1007 E mail support patton com WWW www patton com Part Number 07MCL1214 UM Rev C Revised October 9 2014 Patton Electronics Company Inc 7622 Rickenbacker Drive Gaithersburg MD 20879 USA Tel 1 301 975 1000 Fax 1 301 869 9293 Support 1 301 975 1007 Web www patton com E mail support patton com Trademark Statement The term CopperLink is a trademark of Patton Electronics Company All other trade marks presented in this document are the property of their respective owners Copyright O 2013 2014 Patton Electronics Company All rights reserved The information in this document is subject to change without notice Patton Electronics assumes no liability for errors that may appear in this document Warranty Information Patton Electronics warrants all CopperLink components to be free from defects and will at our option repair or replace the product should it fail within one year from the first date of the shipment This warranty is limited to defects in workmanship or materials and does not cover customer damage abuse or unauthorized modification If the product fails to perform as warranted your sole recourse shall be repair or replacement as described ab
5. 1000 ft 305m 126 54 SON 2 000 ft 610m 60 21 S1 20N FastPath 000ft 914 m 42 6 S1 3 OFF 3 500 ft 1km 35 1 Note The actual distance and link performance may vary depending on the envi ronment and type gauge of wire used Note DS downstream US upstream Note This chart applies to CL1214s with a twisted pair line interface CL1214 EUI and CL1214 TB Contact Patton for CL1214 BNC rates Line Rate amp Reach Chart Based on 24 AWG 0 5 mm 37 Line Rate amp Reach Chart Based on 24 AWG 0 5 mm 38
6. Equipment WEEE ensure that at end of life you separate this product from other waste and scrap and deliver to the WEEE collection system in E your country for recycling 10 CopperLink 1214 User Manual About This Guide A WARNING A WARNING A CAUTION This device contains no user serviceable parts This device can only be repaired by qualified service personnel This device is NOT intended nor approved for connection to the PSTN It is intended only for connection to customer premise equipment Electrostatic Discharge ESD can damage equipment and impair electrical circuitry lt occurs when electronic printed circuit cards are improperly handled and can result in complete or inter mittent failures Do the following to prevent ESD Always follow ESD prevention procedures when removing and replacing cards Wear an ESD preventive wrist strap ensuring that it makes good skin contact Connect the clip to an unpainted surface of the chassis frame to safely channel unwanted ESD voltages to ground To properly guard against ESD damage and shocks the wrist strap and cord must operate effectively If no wrist strap is available ground yourself by touching the metal part of the chassis 11 Chapter 1 General information Chapter contents Oven ic Md Je tg RE ue RIO RD E U EEUU EH E UU Neer ELON sorone nnnm 12 CopperLink 1214 User Manual 1 General information Overvie
7. guide to help you become aware of potential Router modem problems Warnings relate to personal injury issues and Cautions refer to potential property damage A note presents additional information or interesting sidelights The alert symbol and IMPORTANT heading calls attention to important information IMPORTANT The alert symbol and CAUTION heading indicate a potential haz ard Strictly follow the instructions to avoid property damage CAUTION CopperLink 1214 User Manual About This Guide CAUTION WARNING A WARNING The shock hazard symbol and CAUTION heading indicate a potential electric shock hazard Strictly follow the instructions to avoid property damage caused by electric shock The alert symbol and WARNING heading indicate a potential safety hazard Strictly follow the warning instructions to avoid personal injury The shock hazard symbol and WARNING heading indicate a potential electric shock hazard Strictly follow the warning instructions to avoid injury caused by electric shock CopperLink 1214 User Manual About This Guide Safety When Working With Electricity device can only be repaired by qualified service person i This device contains no user serviceable parts This nel WARNING Do not open the device when the power cord is con nected For systems without a power switch and without an external power adapter line voltages are present within the device when the power cord is connected
8. HS DN Line COUTA RR RSA 17 Connecting Power ea een an costae ig a EUR E da WEE HEU Ede EUR aaa 18 A RO n aU nine vanes ao e eM RE 19 In ea LL RS 20 Contisuriig the Hardware DID Switches ee als aan 20 Conto DIP Sich Si eoor a uu Mu c E E ete shale OBS a 20 MOD ps Seat ata Sas cds aces oe cu os tudos Ses CEEE vou sou eT IDONEUS D d es po Tinto ditch y PPP CCOO M 23 Prone Panel LED Serro Non tod ceno RO S E D EU EE ESSE 23 5 Contacting Patton for assistance asse aima me pim perm tc 24 Mesue l e Q 25 Contact normano Tio ae ate eee ile 25 Warranty Service and Returned Merchandise Authorizations RIMA osa is 25 VIE IZ MRO E 25 RMA umber e nilo Solenne inni rd ne uan loi Se n e ii e 26 A Compliance information turale I a E RA to 27 boiled E 28 EMO EVE nasa 28 ere graec Die ane a en oa uniao geet n 28 ego aci leo o E DR doa E E 28 Radio and 1V nenem FOC Part IS si E R court 28 CE Deanin ona a O ree op APIS 28 Authorized European RE asa FR 28 SERVICE rane aaa naar aaa art 29 CopperLink 1214 User Manual Table of Contents B Specifications ici ail e ail 30 LAN Connect ea 31 Transmission Line ion 31 LED Setas Ida RO e oen tem am ROB RO 31 Power Supply MTT 3l External AG and Internal DG Options e oerte reU eoo Rn EO EORR ha per REOR aran 3l jun 31
9. However there is no guarantee that interference will not occur in a particular installation If the device does cause interference to radio or television reception which can be determined by disconnecting the unit the user is encouraged to try to correct the interference by one or more of the following measures moving the computing equipment away from the receiver re orienting the receiving antenna and or plugging the receiving equipment into a different AC outlet such that the computing equip ment and receiver are on different branches CE Declaration of Conformity Patton Electronics Inc declares that this device is in compliance with the essential requirements and other rele vant provisions of Directive 2004 108 EC relating to electromagnetic compatibility and Directive 2006 95 EC relating to electrical equipment designed for use within certain voltage limits The Declaration of Confor mity may be obtained from Patton Electronics Inc at www patton com certifications The safety advice in the documentation accompanying this device shall be obeyed The conformity to the above directive is indicated by CE mark on the device Authorized European Representative DRM Green European Compliance Services Ltd Greyfriars Court Paradise Square Oxford OX1 1BE UK Regulatory Information 28 CopperLink 1214 User Manual A Compliance information Service All warranty and non warranty repairs must be returned freight prepaid and
10. NR 9dB Better line noise protection with SNR up to 9dB Introduction 21 Chapter 4 Operation Chapter contents edi OOO n Brent Panel LED Sas Montorio inn 22 CopperLink 1214 User Manual 4 Operation Introduction Once the CL1214s are properly installed they should operate transparently No user settings required This section describes reading the LED status monitors Before applying power to the CL1214 please review Connecting Power on page 18 to verify that the unit is connected to the appropriate power source Front Panel LED Status Monitors The CL1214 features six front panel LEDs that monitor power the Ethernet signals the CopperLink connec tion and the remote local setting figure 8 shows the front panel location of each LED Table 5 on page 23 describes the LED functions of Aw di UL Link E Remote Unit Local Unit f CopperLink Power Figure 8 CL1214 front panel Table 5 Front panel LED description LED Status Description Power Green The device is powered on Off The device is powered off CopperLink Green The port is connected Blinking Green Data transceiving of No valid link on this port Ethernet Green The port is connected Blinking Green Data transceiving Local Green The device acts in Local mode Off Local mode is off Remote Green The device acts in Remote mode Off Remote mode is off a Once the
11. Operating Temperature AAA NN 31 Hindi nea SG ER Eee Ecce aa no ana Ree ET 31 juro M 31 C Factory Replacement Parts and Accessories eire cette ao 32 CL1214 Series Factory Replacement Parts and Accessories essere enne 33 D Interface Pim Assioniment eerte tete toi ateus ioa px een dada as cada eo epe Aux Ie ent peeing opo Eoo Lone oe eaaet dad epa eot sas 34 TO TOODAses Vette et Aes eet trei eere erede ter herr eric EDS ep E bx aa DE gas totae SA E ER De a 35 Coppel x V 35 BOTS ISDN Interface COTA aaa 35 E Line Rate cde rM ara 36 Line Rate amp Reach Chart Based on 24 AWG 0 5 mm cccccssssscscssssssecccevssssscecosevsenceesceseseecscevseseeevesceeveeaveese 37 List of Figures WO 0 AM EO Typical application ss rara sis A DESSE CRIA Se SUNS E ESSES ES eR HO ER 13 CL panela pena cada leale aa AA e epic dnt tus 15 ELI2141R1 45 twisted pair lie nte opera parana a nar Ea 16 lil Terminal Bloc itwvisted pa line dei ee Sepp na eae enn ab suo DR UE 17 CLIO T8 D05PO0 Basel Bjs Connector DI oHt usos da CCI asd CAS Co aR EDSON Ome eae E 17 CLS RIA BOU SIS N nda se cc dE o ae 18 eee ao ora 20 CLA on pane Mte 23 acne ecc eei cu TTA A TT Da List of Tables N WW KR OD N e SCI SUMA sche etre eee RE USE Ge CES REI 20 Local Renmore ion anno 21 Symmicific Asymmiecthie SelectioniChart 55 assi ta FEE anali ariani ape OEE EE Cada S
12. ail support e mail sent to support patton com will be answered within 1 business day Telephone support standard telephone support is available five days a week from 8 00 am to 5 00 pm EST 1300 to 2200 UTC by calling 1 301 975 1007 Warranty Service and Returned Merchandise Authorizations RMAs Patton Electronics is an ISO 9001 certified manufacturer and our products are carefully tested before ship ment All of our products are backed by a comprehensive warranty program Note Ifyou purchased your equipment from a Patton Electronics reseller ask your reseller how you should proceed with warranty service It is often more con venient for you to work with your local reseller to obtain a replacement Patton services our products no matter how you acquired them Warranty coverage Our products are under warranty to be free from defects and we will at our option repair or replace the prod uct should it fail within one year from the first date of shipment Our warranty is limited to defects in work manship or materials and does not cover customer damage lightning or power surge damage abuse or unauthorized modification Out of warranty service Patton services what we sell no matter how you acquired it including malfunctioning products that are no longer under warranty Our products have a flat fee for repairs Units damaged by lightning or other catastro phes may require replacement Returns for credit Customer satis
13. cceptable 2 The CL1214 is equipped with an RJ 45 interface jack figure 3 or terminal block figure 4 on page 17 that can be used on the CopperLink interface The CopperLink interface is a two wire interface Observe the signal pin relationships on the CL1214 s CopperLink interface jack The RJ 45 connector on the CL1214 s twisted pair interface is polarity insensitive and is wired for a two wire interface The signal pin relationship is shown in figure 3 1 no connection 1 a 2 no connection 2 3 no connection fe 4 RING 5 TIP 4 5 6 no connection 8 7 no connection 8 no connection Figure 3 CL1214 RJ 45 twisted pair line interface Connecting the Line Interface 16 CopperLink 1214 User Manual 2 Installation am di ay j au O O 42 2 g RING IP Figure 4 CL1214 Terminal Block twisted pair line interface Connecting the Line Interface for CL1214 BNC To connect the line interface of the CL1214 BNC simply use a coaxial cable with a BNC connector at each end to connect the pair of CL1214s Connecting the 10 100Base T Ethernet Interface and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use The RJ 45 ports labeled Ethernet are the Auto MDIX10 100Ba
14. e The CL1214 does not have a power switch so it powers up as soon as it is plugged in An external AC or DC power supply is available separately This connection is made via the barrel jack on the rear panel of the CL1214 No configuration is necessary for the power supply See Appendix B for domestic and international power supply and cord options DC power supplied via the power supply jack to the CL1214 must meet the following requirements DC power supplied must be regulated 12VDC 5 1 0A minimum Center pin is 12V The barrel type plug has a 2 5 5 5 10mm I D O D Shaft Length dimensions Connecting Power 18 Chapter3 Configuration Chapter contents liscsier mm 20 Contiene the Hardware DIP Switches nene ere aaa ionici 20 Costi 20 RIETI LIO RR RN NI 21 Switches S1 2 and 51 3 Symmetricl Asymmetric Operation cete ettet teret bnt 21 Switch ds General Prorectton Signal to Noise Ratio celle 21 19 CopperLink 1214 User Manual 3 Configuration Introduction The CL1214 has eight DIP switches S1 for configuring the unit for a wide variety of applications This sec tion describes switch locations and explains the different configurations Configuring the Hardware DIP switches The DIP switches are externally accessible from the underside of the CL1214 Figure 7 shows the orientation of the DIP switches in the On and Off positions Push toggle up for ON position Push toggle EmmummmS 2345678 LS
15. e es 21 palito Nos adios A estinta 21 Trone panel LE dese ton udo eme vtae tol mete uc E dM M E ge 23 Line Rate amp Reach Chare Osing Tyisted Fair Long Range ses eime ERES na espera E 37 Line Rate amp Reach Chart Using Twisted Pair High speed pas e ni eta 38 About This Guide This guide describes the CopperLink Model 1214 hardware installation and basic configuration Audience This guide is intended for the following users Operators Installers Maintenance technicians Structure This guide contains the following chapters and appendices Chapter 1 on page 12 provides information about CL1214 features and capabilities e Chapter 2 on page 14 provides information about installing the CL1214 CopperLink interfaces e Chapter 3 on page 19 provides information about the CL1214 configuration Chapter 4 on page 22 provides information about the CL1214 s operation Appendix A on page 27 provides compliance information for the CL1214 Appendix B on page 30 provides specifications for the CL1214s Appendix C on page 32 provides a table of replacements for parts and accessories Appendix D on page 34 provides diagrams of detailed pin assignments Appendix E on page 36 provides a line range and reach chart for the CL1214 For best results read the contents of this guide before you install the CopperLink 1214 Precautions Notes and cautions which have the following meanings are used throughout this
16. faction is important to us therefore any product may be returned with authorization within 30 days from the shipment date for a full credit of the purchase price If you have ordered the wrong equipment or you are dissatisfied in any way please contact us to request an RMA number to accept your return Patton is not responsible for equipment returned without a Return Authorization Introduction 25 CopperLink 1214 User Manual 5 e Contacting Patton for assistance Return for credit policy Less than 30 days No Charge Your credit will be issued upon receipt and inspection of the equipment 30to 60 days We will add a 20 restocking charge crediting your account with 80 of the purchase price Over 60 days Products will be accepted for repairs only RMA numbers RMA numbers are required for all product returns You can obtain an RMA by doing one of the following Completing a request on the RMA Request page in the Support section at www patton com By calling 1 301 975 1007 and speaking to a Technical Support Engineer By sending an e mail to returns patton com All returned units must have the RMA number clearly visible on the outside of the shipping container Please use the original packing material that the device came in or pack the unit securely to avoid damage during shipping Shipping instructions The RMA number should be clearly visible on the address label Our shipping address is as follows Patton Electronics Compan
17. insured to Patton Electronics All returns must have a Return Materials Authorization number on the outside of the shipping container This number may be obtained from Patton Electronics Technical Services at Tel 1 301 975 1007 Email support patton com URL http www patton com Packages received without an RMA number will not be accepted Service 29 Appendix B Specifications Chapter contents LAN Connection alan 31 A casale EDUENSIS 31 CE SS mu urs a adire esses A A A E 31 E ery e M SAR 31 External AC and Internal DE options reina 31 o MERRILL IMS 31 Operating Fernperat ate Ranco ri 31 no em e cc I n T 31 TO 31 30 CopperLink 1214 User Manual LAN Connection B Specifications Four RJ 45 10 100Base T IEEE 802 3 Ethernet e CopperLink Connection RJ 45 Transmission Line Two wire unconditioned twisted pair or 75 ohm BNC LED Status Indicators e Power Green CopperLink Link Green Local Green Remote Green Ethernet Link Green amp Activity Flashing Green Power Supply External AC and Internal DC options AC 120 VAC 220 VAC and UI 120 240 VAC DC 12 VDC 24 VDC and 48 VDC Power consumption 400mA at 12VDC Physical Operating Temperature Range 0 50 C Humidity Up to 90 non condensing Dimensions 6 22 W x 1 25 Hx 4 75 Din 157 W x 318 Hx 120 D mm LAN Connection 31 Appendix C Factory Replacement Parts and Accessorie
18. ove Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product These damages include but are not limited to the following lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Patton Electronics specifically disclaims all other warran ties expressed or implied and the installation or use of this product shall be deemed an acceptance of these terms by the user Summary Table of Contents m m OO gt VR N Generalinformationi cieca 12 Tista lest chin sonata 14 A EE 19 OP ri Do Contacting Patton Tor assistance cec tenete leer er tenerte ine e tnt dt Uer Ye ai 24 Compliance mattoni ERR 27 E EM 30 Factory Replacement Parts and Accessories near ie 32 utertace DI Asie RGE ROS PORN A cat e RR e e Seen o a Re E E RR i 34 Line Rate O 36 Table of Contents a Maple N E NE N rinite 3 Table of Contente sre DRE TIT a lyase Reese ens E A RAI CLE UI D LI 4 List of Figures List of Tables PDO MSGS LIAS nno rca 8 Satety When Working With Electric ia 10 MEE eur A UD E 12 IT EIE 13 o Wn Me ine 13 a O RR RR hene RR Re in 13 2 Installation cohen nen Ss as e eee e as ani 14 Plaumnineetenstallatiglh ecole ecce etre is 15 Gonogectine the Line rra irreali ica 16 Connecting the TO TUOBase T Ethernet Interface eee eere etae epe ee 17 Connective the OS
19. resses only passing packets across the CopperLink link that are meant for the remote peered LAN IP Video Corporate E Network 168 Mbps n MEM over Cat 5 Coax UTP EEE WT Y Remote Location Guard House Card Reader Remote Network Connectivity rs sso Primary Office Corporate LAN Figure 1 Typical application The pair of CL1214 models work together to create a transparent extension between two peered Ethernet LANs using twisted pair 2 wire Cat5 or 75 ohm BNC Figure 1 shows a typical point to point applica tion Overview 13 Chapter 2 Installation Chapter contents Pompilio lia PII ian heces mee 15 Gonnecting the Lino lar reali 16 Connectne the Line Interface tor GLI2I4 E MI CIA on 16 Esc ce tooo 17 Connecting the 10 100Base T Ethernet nente isa 17 Connecting he DO A cete enl ru T Ee 17 COIE Power RR RARO 18 14 CopperLink 1214 User Manual 2 Installation Planning the Installation and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The Interconnecting cables shall be acceptable for external use To install the CL1214 Ethernet Extender do the following 1 Connect the line interface between the units refer to Connecting the Line Interface on page 16 Note See figure 2 for the CL1214 s rear panel arrangements 2 Connect the Ethernet interface refer to
20. rface RJ 45 Pin 4 RING Pin 5 TIP Pins 1 2 3 6 7 8 no connection RING TIP Figure 9 Terminal Block POTS ISDN Interface CL1214 S RJ 45 Pin 4 2 wire RING Pin 5 2 wire TIP Pins 1 2 3 6 7 8 no connection 10 100Base T Interface 35 Appendix E Line Rate amp Reach Chart Chapter contents Line Rate Se Reach Chart Based om 2A 0 5 rante 36 CopperLink 1214 User Manual Ee Line Rate Reach Chart Line Rate amp Reach Chart Based on 24 AWG 0 5 mm Table 6 Line Rate amp Reach Chart Using Twisted Pair Long Range Mode Distance in Feet Long Range ft m km 250 ft 76m 67 16 x id 1000 ft 305 m 59 16 symmetric 81 2 ON 2 000 ft 610m 45 11 S1 3 ON 3 000 ft 914 m 31 5 5 000 ft 1 5 km 17 682 kbps 10 000 ft 3km 4 263 kbps Note The actual distance and link performance may vary depending on the envi ronment and type gauge of wire used Note DS downstream US upstream Note This chart applies to CL1214s with a twisted pair line interface CL1214 EUI and CL1214 TB Contact Patton for CL1214 BNC rates Table 7 Line Rate amp Reach Chart Using Twisted Pair High Speed Mode Distance in Feet High Speed ft m km 250 ft 76m 121 144 Fun 1000 ft 305 m 73 103 LE 2 000 ft 610m 45 37 3 000 ft 1914m 46 10 3 500 ft 1km 30 4 Asymmetric 250 ft 76m 168 95 S1 2 OFF Standard
21. s Chapter contents CLIZIA Series Factory Replacement Parts and Accessories 32 CopperLink 1214 User Manual C Factory Replacement Parts and Accessories CL1214 Series Factory Replacement Parts and Accessories Patton Model Base Models CL1214 EUI 2PK Description High Speed CopperLink Ethernet Extender Kit Local and Remote RJ45 Line 100 240VAC CL1214 TB EUI 2PK High Speed CopperLink Ethernet Extender Kit Local and Remote Ter minal Block Line 100 240VAC CL1214 BNC EUI 2PK High Speed CopperLink Ethernet Extender Kit Local and Remote BNC Line 100 240VAC CL1214 S EUI 2PK High Speed CopperLink Ethernet Extender Kit Local and Remote RJ45 Line POTS ISDN 100 240VAC 07MCL1214 UM User Manual Power Supplies PS 03671H1 002 100 240VAC 12V DC 2A Wall mount power adapter Power Adapters 12 130 European replacement plug 12 129 American replacement plug 12 131 United Kingdom plug 12 132 Australian Chinese plug CL1214 Series Factory Replacement Parts and Accessories 33 Appendix D Interface Pin Assignment Chapter contents DON NOVO as eae Ente eet iena letale ner Cop son cos uU E EEUU sli sini inn dn POTSISDN neretto AS EE 34 CopperLink 1214 User Manual 10 100Base T Interface D e Interface Pin Assignment RJ 45 e Pin 1 TX e Pin 2 TX Pin 3 RX Pin 6 RX Pins 4 5 7 8 no connection CopperLink Inte
22. se T interface These ports are designed to con nect directly to a 10 100Base T device or network figure 5 shows the signal pin relationships on this interface You may connect this port to a hub or PC using a straight through or crossover cable that is up to 328 ft long 1 TX RX we 2 TX RX 1 5 nM Lu NE LL 3 RX TX 4 4 no connection 5 5 no connection 5 _ 6 RX TX 8 7 no connection 8 no connection Figure 5 CL1214 10 100Base T RJ 45 Connector Pin out Connecting the Line Interface 17 CopperLink 1214 User Manual 2 Installation Connecting the POTS ISDN Line CL1214 S On the CL1214 S model the RJ 45 port labeled is the POTS ISDN interface A telephone may be con nected to this port and carried over the CopperLink line The units do not need power for the POTS interface to work The RJ 45 connector in the POTS ISDN interface is wired as shown in figure 6 1 no connection 1 ue 2 q i gr no connection 4 4 2 wire RING no connection 5 5 2 wire TIP 6 no connection 8 ls 7 no connection 8 no connection Figure 6 CL1214 S RJ 45 POTS ISDN interface Connecting Power and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external us
23. unit connects to a power source the Link LED will blink as the CL1214 automatically looks for the other unit in the pair Introduction 23 Chapter 5 Contacting Patton for assistance Chapter contents IR II I O Ree AR DETULIT 25 Contaci informations alal he EI AGR en Do IE dali 25 Warranty Service and Returned Merchandise Authorizations RIMAS rio 25 ANE ACENDE RAR ECCE E E S E E IE STA REI 25 Ba e L a E RUN RN UR EE E EE E nanna 25 al EE TE AAT EA AA uie eite ta fett edat i E AA 25 Return for eredi pole eene e ee ER Rana 26 SAN nao jap o I E E ec cea E TO 26 ia eit deir GM S noli iN i PRE 26 24 CopperLink 1214 User Manual 5 e Contacting Patton for assistance Introduction This chapter contains the following information e Contact information describes how to contact Patton technical support for assistance Warranty Service and Returned Merchandise Authorizations RMAs contains information about the RAS warranty and obtaining a return merchandise authorization RMA Contact information Patton Electronics offers a wide array of free technical services If you have questions about any of our other products we recommend you begin your search for answers by using our technical knowledge base Here we have gathered together many of the more commonly asked questions and compiled them into a searchable database to help you quickly solve your problems Online support available at www patton com E m
24. w Thank you for your purchase of this Patton Electronics product This product has been thoroughly inspected and tested and is warranted for one year for parts and labor If any questions or problems arise during installa tion or use of this product contact Patton Electronics Technical Support at 1 301 975 1007 Features e Variable rate CopperLink extender Easy to configure e Auto MDIX Ethernet Configurable 10 100 Full Half and Auto Negotiating Ethernet Extends up to 4x 10 100Base TX Ethernet beyond 328 foot 100 meter limitation over a single twisted pair Cat 5e 6 7 or coaxial cable Symmetric or asymmetric settings via DIP switch Transparent operation LED indicators for Power CopperLink Ethernet Link Activity Remote and Local Description The Patton Electronics CL1214 CopperLink modems provide high speed LAN connections between peered Ethernet LANs remote PCs or any other network enabled 10 100Base T device Operating in pairs one CL1214 is configured as the L Local unit located at one end of the LAN extension and the other CL1214 is configured as the R Remote unit at the other end The CL1214 is configured as a L or R via the switch on the bottom of the unit These units can automatically forward LAN broadcasts multi casts and frames across a 2 wire voice grade twisted pair or BNC link The data is passed transparently unmodified through the CL1214s The CL1214s automatically add and delete MAC add
25. y RMA xxxx 7622 Rickenbacker Dr Gaithersburg MD 20879 4773 USA Patton will ship the equipment back to you in the same manner you ship it to us Patton will pay the return shipping costs Warranty Service and Returned Merchandise Authorizations RMAs 26 Appendix A Compliance information Chapter contents bora RR 00 28 EMEC recensite 28 loto 28 POEN te ce e 28 Radioand TV bwerterence FOC Part 15 envers nina 28 CER rollin GRC non boe eds ener 28 AugorizedEyrapeanRepresenbat e RR RR 28 A 29 27 CopperLink 1214 User Manual A Compliance information Regulatory Information EMC Directive e FCC Part 15 Class A EN55022 Class A EN55024 EN50581 Low Voltage Directive Safety EC EN60950 1 2nd Edition UL60950 1 CSA C22 2 No 60950 1 PSTN This device is not intended nor approved for connection to the PSTN Radio and TV Interference FCC Part 15 This device generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturers instructions may cause interference to radio and television reception The device has been tested and found to comply with the limits for a Class A computing device in accordance with specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection from such interference in a commercial installation
Download Pdf Manuals
Related Search