Installation, commissioning and operating instructions
Contents
1. Page 29 40 If the system detects that the last calibration point is too far away from the theoric value the temperature sensor calibration is cancelled and Calibration ERROR message is displayed That means the temperature sensor is working bad or is broken Please replace it immediately gt Displaying temperature or not By pressing on OK key whereas the line Temperature display is in intensified brightness allows to have access to the choice of activation or deactivation of the temperature displaying in the main screen The and keys allow to select ON or OFF state The validation is done by pushing OK key gt Factory settings By pressing on OK key whereas the line Factory settings is in intensified brightness allows to reload the memory by default settings like statement in the paragraph The sensor connected to El entry is displayed on the left part of the screen F j a gi m The sensor connected to E2 entry is displayed on the right part of the Communication screen V X XX SN XXXXXXXXX To validate press OK key To cancel press ESC key Be careful This operation is irreversible Once validated by OK key all your personal configuration parameters will be lost gt Communication Configuration Language By pressing on OK key whereas the line Communication is in Contrast intensified brightness allows to have access to communication RS485 Non iicn E ModBus configurati2. A gt Wire the two wires to 11 and 12 located on P1 gt Wire the ground cable on PE 13 located on P1 gt Tighten the cable gland to ensure tightness when done e Connecting the powered relay P2 Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 18 40 The self powered relay output P2 Primary voltage Available voltage on P2 is used to control the measurement parameter connected on E2 gt Strip the 2 wires of dosing equipment for 7mm gt Pass the 3 point cable through a cable gland A gt Wire the two wires to 14 and 15 located on P2 gt Wire the ground cable on PE 16 located on P2 gt Tighten the cable gland to ensure tightness when done 9 Connecting the measurement inputs The TERE O controller has three measurement inputs with different version either gt 4 20mA analogical inputs used to measure multi parameters using isolated current loop from a sensor or from a specific housing chamber with integrated converters gt Special integrated modules soldered into the controller for direct measurement sensors a 4 20mA analogical inputs without internal module version All entries are self powered by internal 12VDC power supply and must be used without external supplies Analogical entries of the controller are not isolated The use of SYCLOPE Electronique technology measuring cells is mandatory They use a special internal isolation war
3. Bromine Terminal E3 BNC E1 Terminal E2 T C pH Redox Terminal E3 BNCE1 BNCE2 Wiring of the pH and Redox ORP entries must be respected Risks of uncontrolled injection of chemical products Dont touch internal pin of the BNC connectors Risks of destroying internal electronic components Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 20 40 10 Connecting the voltage reference REF fp Sensors REF no The voltage reference allow you to power the external electronic converters It is programmable to deliver a 12V power supply Do not invert polarity e Red wire on Brown wire on 11 Wiring the external control entry E4 The TERE O controller has a remote control input E4 which stops the controls of dosing equipments This input is a 4 20mA analogical input An external resistor is normally connected on this entry for authorizing dosing processes if not external command is requested If you decide to control dosing processes by an external signal you must realize the function as follow For safety reason it is strongly recommended to use this function with an external switch which comes from the filtration system to prevent overdosing of chemical products a Version with 4 20mA sensor used by SYCLOPE When using SYCLOPE measuring cells it is optional to have an analogical flow switch detector un
4. Displaying dosing controls The dosing control symbol can take five different statutes WR Automatic dosing control Dosing control in pause Dosing control stopped s 7 20 Dosing control deactivated Main stop Manual dosing control Manual working When started the controller dosing control is stopped By pressing on START key launches the regulation of the two parameters according their setting points If the sensor polarization is not finished the symbol is present the regulation is in pause mode symbol LI When polarization is finished the symbol disappears the automatic dosing controls are activated a If you wish to select manual dosing control on one of the two parameters press on the MODE key allows to pass in manual dosing control ae CET an additional pressing on MODE key allows to pass in desactived mode symbol ET again another additional pressing on MODE key allows to return in automatic mode By pressing on STOP key allows to stop the regulation of the two parameters symbol LD Pressing MODE key is without effect when the regulation is stopped gt Displaying alarms Bottom of the display part informs about the thresholds and the states of alarms fea High alarm value Threshold 8 3pH High alarm activated Low alarm value Threshold 6 5pH Low alarm activated an Ti a Cie En tg n Ts CT lw CEE L D oo T gt Displaying statutes in the higher display band The hi
5. Email service technique syclope fr 2012 2015 by SYCLOPE Electronique S A S Subject to modifications
6. automatic lock system which must be understood to manipulate it For opening the transparent door a BEA w kA Raise the lock and pull Opened forward it Locked For opening and locking transparent door if Pass the fingers behind the With the palm of the hand Locked lock and bring the door with press on the transparent door the inch and tighten with the hand to lock 4 Opening Closing connection cover To ensure IP65 protection class the connection cover must be closed after usage and the O ring must be checked each time Use a specific screwdriver to remove the two screws for opening the cover SYCLOPE I i DCI Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 15 40 A A A 5 Electrical connections The electrical installation must be performed in accordance with current standards by authorized personnel A 30mA differential circuit breaker must be installed A breaker circuit of maximum 10A must be installed near the controller and easily accessible to stop the main power It must be identified as a circuit breaker for the controller Before performing the connections remember to turn off the power Use multicore cables if possible If not possible always use a special wiring tip to be sure that wires do not make a contact together Protect the wirings by using electrical clamps
7. d i Reconnect the flat cable between the electronic cards and put the 4 screws to fix the front face Don t screw them hardly because the electronic box is made in plastic material U bad i ba 7 Connecting primary power supply The SYCLOPE TERE O controller is equipped with a switching power supply It is therefore able to be supplied by AC voltage comprised between 90V to 240V 50 60Hz Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 17 40 gt Use a 3 point 1 5 mm cable to wire the power supply gt Strip the 3 wires for 7mm gt Pass the 3 point cable through a cable gland A gt Wire the live cable to FT and the neutral to located X1 gt Wire the ground to the ground plot with an insulated round terminal Cabler la terre sur le plot PL1 l aide d une cosse a illet M4 gt Tighten the cable gland to ensure tightness when done Terre The SYCLOPE TERE O controller does not have its own independent power switch It is directly powered when connected to the main power supply 8 Connecting the self powered relay P1 e Connecting the self powered relay P1 LENIPE P 1 The self powered relay output P1 Primary voltage Available voltage on P1 is used to control the measurement parameter connected on E1 gt Strip the 2 wires of dosing equipment for 7mm gt Pass the 3 point cable through a cable gland
8. in the gravitating return line e The sensors installed into the measuring cell receive water to be analysed and send the values to the controller e According to the setting points fixed by the user the controller sends proportional orders to the pumps installed into the main intake line of the swimming pool swimming pool and the return line The water must be homogeneous before coming in the A Be careful to the distance between the injection points of chemistry products into the return line 2 Measurements come from recirculating line T This type of installation is recommended in the event of single swimming pool where filtration circuit is independent Utilisations g n rales Page 24 40 e Water is sampled after the recirculating pumps and before the filter entry If using before flocculent injection circuit e The sensors installed into the measuring chamber receive water to be analysed and send the values to the controller e According to the setting points fixed by the user the controller sends proportional orders to the pumps installed into the main intake line of the swimming pool Swimming pool Dosing pumps Sampling Heater TOR nn circuit ms Circulation pump Swimming pool controller Sampling circuit TT Measuring cell Circulation pump Installation commissioning and operating instructions SYCLOPE TERE O Commissio
9. of the polarization time for the corresponding sensor A 0 H Mode Key a short push makes it possible to select the operating process of the controller Manual or AUTO when the regulation is launched START Key A long push gives access the adjustments of the sensor parameters ol START i i STOP Start Stop Key allows to activate deactivate the processes O The sensor connected to E1 entry is displayed on the left part of the screen The sensor connected to E2 entry is displayed on the right part of the screen Programming the controller Page 27 40 2 lt Factory setting values Whatever the type of operation chosen the following configurations are carried out by the factory e Language French e Contrast 50 e Parameter 1 Chlorine range 10ppm Set point 2ppm High threshold 5ppm Low threshold 1 5ppm e Parameter 2 pH Set point 7 2pH High threshold 8 5pH Low threshold 6 5pH Flow control entry NC Normally closed Controls Inactives Proportional band Bp 10 Cycle time of PWM 120 s 3 Principle of programing The display of the SYCLOPE TERE O controller is separated in 3 parts gt A main programming screen gt A label for each parameter adjustment gt A screen of measurement values and dosing in progress ain programming menu A long push on one of the two ESC keys gives access to the main programming menu once in the this menu a short push on ESC key
10. It has been carefully developed and manufactured to ensure your greatest pleasure and peace of mind Its remarkable capacity for adapting to different conditions and sizes of private or public swimming pools means it can be installed in the most difficult of environments where control of water treatment and swimming pool water regulation processes are decisive The SYCLOPE TERE O range are equipped with one temperature entry and two specific electronic card adaptors for pH ORP or chlorine bromine for measurements using specific sensors for treating Swimming pool water and also include regulations processes with cyclic commands transmitted by means of two relays to control pH and chlorine levels The simplicity of operation of the SYCLOPE TERE O the user friendliness and the remarkable technical aspects of these devices will ensure you benefit from their many options guaranteeing you full control and supervision of the quality of the water in your swimming pool The following instructions contain all the information required for the installation use and maintenance of your new equipment gt Packaging gt Installation gt Technical specifications gt Commissioning instructions gt Safety tips If you would like to receive further information or if you encounter any difficulties not described in this manual please contact your usual retailer or else directly contact the sales department of SYCLOPE Electronique in France eit
11. SYCLOPE TERE O controller for swimming pools Part 1 vs LL De ee Pion Pegel See 0 40 eee 7 20 _ PEF E 2 25 1 00 0 30 Installation commissioning and operating instructions SY PE Ele Que ae Reference TEROOOO TEROO10 TEROO20 TER xxxx Rev 5 1 General informations Page 2 40 Parts of the general documentation pm Part 1 Manual of installation commissioning and operating instructions Part 2 Manual of communication instructions General informations SYCLOPE Electronique 2013 Notice of 11 08 2015 Rev 5 1 Analysers controller for private and public swimming pools Gamme TERE O Installation commissioning and operating instructions Editor S y DE SYCLOPE Electronique S A S Z I A ropole pyr n es Elec que Rue du Bruscos 64 230 SAUVAGNON France Tel 33 05 59 33 70 36 Fax 33 05 59 33 70 37 Email syclope syclope fr Internet http www syclope fr 2012 2015 by SYCLOPE Electronique S A S Subject to modifications Content Page 3 40 Content P ol fo cic Deer tee eee mene teen ae Ene ren ERR TT Se on PERE Pen Eee ne aL ee eo ren ee ne ene 4 Dy ORED 1610 a a N r a D 4 2 FOC CON OT waa E r A da et ae Rae 5 3 GUSA AdO CUME ean a incurs mate A eee 6 4 SIgnS and Sale SVIMDOIS SR A seep art den ni tes sua 6 5 Storage and transposer nue area nee 7 Oy PACKA ER vounnaies T 7 7 Wanani dinde hu DO cuit eee aes 7 II En
12. The SYCLOPE TERE O controller must be connected to the main circulation pump system by means of E4 entry and with the flow switch of the measuring chamber Internal protection gt The controller is protected by an internal resettable fuse of 160mA and by a varistor of 275VAC for surge protection The self powered relays P1 and P2 are protected each by a glass 5x20 fuse of 5A 250V Reference Name FUS5X20R5000 Fast glass fuse 5x20mm 5A 250V In case of fuse destroyed check that the card is not burnt out If this is the case the complete card must be changed In case of varistor burned please return the controller to our technical after sales department for repairing 6 Changing internal fuses of P1 and P2 outputs Before changing any fuse disconnect the power supply Use only an original fuse Don t replace it by another one with a higher current Open the translucid door and remove the 4 screws with an adequate screwdriver Disconnect de flat cable between the electronic cards carefully Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 16 40 Localise the fuse to be changer on the bottom card Remove the protection cover on the support of fuse Change the fuse and reinstall the protection cover Fuse 1 and fuse 2 Fast fuse 5A 5x20mm Glass PES a3 SAAB SSA BS Bae ale fe aaa A Ee ORE nc A Dt k 2 ae 7 d
13. asure and regulate pH Redox ORP chlorine or bromine by means of sensors and controls of suitable actuators in the context of the possible uses described in this manual All other uses are considered to be non conforming and must therefore be forbidden SYCLOPE Electronique S A S will not be responsible in any case for any damages that result from such Any use of sensors or interfaces not in conformity to the features defined in this handbook must also be proscribed 2 User obligations The user undertakes not to allow its employees to work with the SYCLOPE TERE O equipment described in this manual unless they gt Are aware of the fundamental instructions relating to work safety and prevention of accidents gt Are trained in the use of the device and its environment gt Have read and understood these instructions warnings and manipulation rules 3 Risk prevention performed by personnel specialized and qualified for this task The installation and connection of the SYCLOPE TERE O equipment should only be A The installation must comply with current safety standards and instructions Before switching the controller on or manipulating the relay outputs remember always to cut A off the primary power supply Never open the controller when it is powered on Maintenance operations and repairs should only be performed by trained specialized personnel Take care when choosing the location for installing the equipm
14. ce accept any ifiterference received induding interference that may cause undesired operation D Label of the manufacturer 9 Particular risks Read the notice Model of the product Product which can be recycled G Reference of the product 41 Limitation of dangerous substances a Range of power supply 42 EC compliance G Values of the maximum current Class of protection 7 Identification of the manufacturer Identification plate SN 151909989 vE AZ HEC Be LEE EEE Cu ces may wa eme cms ana ae D ve moe mu P a tet maat ete meet mer men conte meee pene Installation commissioning and operating instructions SYCLOPE TERE O Environment and safety instructions Page 10 40 5 Disposal and conformity The recyclable packaging of the SYCLOPE TERE O equipment must be disposed of according to current regulations cs A mG X Elements such as paper cardboard plastic or any other recyclable elements must be taken to a suitable sorting center According to European directive 2002 96 EC this symbol means that as of 12 August 2005 electrical appliances cannot be thrown out together with household or industrial waste According to current regulations consumers within the European Union are required as of this date to return their used devices to the manufacturer who will take care of disposing them at no extra expense According to European directive 2002 95 EC this symbol means that
15. certificate and according to the original documents of manufacture The following standards were used for the examination 2006 95 EC Harmonized standards EN61010 1 Ed3 2010 2006 95 EC Low voltage directive Safety requirements for electrical equipment for measurement control and laboratory use 2004 108 EC Harmonized standards EN55022 2010 EN55024 2010 EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 EN61000 4 6 EN61000 4 8 EN61000 4 11 EN61000 3 2 and EN61000 3 3 2004 108 EC Electromagnetic compatibility EMC Directive Harmonized standard ETSI EN 301 511 V9 0 2 Harmonized standards ETSI EN 300 328 V1 7 1 Harmonized standards EN62311 2008 EN50385 2002 and EN50383 2002 2002 95 CE RoHS Directive Limitation of dangerous substances Date of the first sale 2013 March The present declaration engages the responsibility of SYCLOPE Electronique S A gt Z I A ropole Pyr n es 64 230 SAUVAGNON Represented by Georges BRETON Sauvagnon 2013 04 17 President Installation commissioning and operating instructions SYCLOPE TERE O Certificat CE Page 38 40 NOTES Installation commissioning and operating instructions SYCLOPE TERE O Certificat CE Page 39 40 Installation commissioning and operating instructions SYCLOPE TERE O SY Eled PE que SYCLOPE Electronique S A S Z 1 A ropole Pyr n es 64 230 SAUVAGNON Tel 33 05 59 33 70 36 Fax 33 05 59 33 70 37
16. d setting point could cause excessive consumptions of calories and harm the environment Before carrying out the calibration pH or Redox or Chlorine or Bromine measurements must be performed with special equipment using chemical reagents This operation does not require the stop the recirculating pumps nor the removing sensors from the measuring cell The chemical reagents for pH or Redox ORP or Chlorine or Bromine measurements are not provided with the controller To proceed an automatic calibration gt Recirculating circuit must work since several minutes gt Displayed value must be stable gt Dosing pumps must be stopped gt 60 oOP amp Eee ET By pressing on the CALIBRATION key causes measured value zone in Ip intensified brightness Use and keys to adjust the value according CL s your reference When done press OK to validate HA During this operation press on ESC key to cancel the calibration or wait 5 n seconds without any action on any key Controller will recover the previous S06 200 gt 7 20 display before calibration procedure If the sensor calibration correctly proceeded the message Calibration OK is displayed Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller Page 35 40 If the system detects that the last calibration point is a little bit away from the theoric value the sensor calibration is done but a Calibration LIMIT m
17. der reference DEBOOOO In this case the external resistor must be removed and the analogical flow switch must be connected as follow Sensors Violet SUS Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 21 40 In this first case E4 entry must be programmed as a NC switch Normally Closed b Version with external free of potential switch When using an external switch from filtration system or flow switch control the electric wiring must be realized as follow Sensors R sistor of 680 Q Switch In this case E4 entry must be programmed as NC switch Normally Connected or NO switch 5Normally Open The controller is provided with NC configuration c Version with PNP inductive switch When using an inductive electronic detector wire as follow Wiring Brown Ref Blue Ref Black E4 a Sensors 3 1e E 4 Inductive detector provided by SYCLOPE is PNP type with 3 wires In this last case E4 entry must be programmed as a NC switch Normally Closed 12 Connecting the RS485 communication port The TERE O controller has a RS485 communication port for connecting to a PLC or a laptop TerCom maintenance software allows you to program the entire controller and to realize the maintenance easily m E A RS485 Installation c
18. derstanding of these instructions n Information gt Action to be taken gt Item of a list or catalogue 4 Signs and safety symbols is a Identify a continuous voltage or a continuous current Identify an alternative voltage or an alternative current Protective ground Functional ground Risk of injury or accident Identify a warning concerning a potentially dangerous risk Documentation must be consulted by the user with each time the symbol is notified If the instructions are not respected that presents a risk of death physical injuries or property damages Electric hazard Identify a warning statement relative to a mortal electric danger If the instructions are not strictly respected that implies an inevitable risk of physical injuries or death Risk of incorrect operation or damage for the device Comment or particular information Recyclable element Installation commissioning and operating instructions SYCLOPE TERE O General Page 7 40 5 Storage and transport order to minimize risk of damage Furthermore the package must be stored in an environment that is protected against humidity and exposure to chemical products It is important to store and transport your SYCLOPE TERE O in its original packaging in Environmental conditions for transport and storage Temperature 10 C to 70 C Air humidity Maximum of 90 with no condensation 6 Packaging D The controller is delivered wi
19. ees 17 9 Connecting the measurement INPUES ccccsecsecnccecseceececeeenecncaeceecneatseeoueaeseesuscnsetsasensatseess 18 10 Connecting the voltage reference REF nn as ie its 20 11 Wiring the external control entry E cccscscsecessccrsscersecurcecuecuseeeuseeersecursesueeesseuseearsesares 20 12 Connecting the RS485 communication port ssssssssssrsnsrsrsrensnnrnnnnrnrnrnrnrnnnrnrnrnrnrnrnrnrnenene 21 V General IS ea cit ae ae E E ERE ent net 23 1 Measurements come from gravity return line sssssssssnsrsrsrsrsrrrnrnnnnrnnnrnrnrnnnrnrnrnrnrnrnrnrnenenene 23 2 Measurements come from recirculating line iii 23 VI COMMISSIONS or nn dates en saree dads wees ne ane ee me ee ee Lin eee 25 VIE Programming TAS Controlle Es a R dard anuule 25 Ly Keypad and EED GIS DIN SR um einen nm nan ein Ge 25 Zy iFacto y gt SEEMING Valse es ei ea tune 27 2 PTINCIDI OT DOUANES an anna te an Ch a tra me une 27 4 POlArSAllON OL SCMSON Len tn nine ie UNS nant aies Unes ne 34 5 Calibration of th SeNSOrS en ni RER ei see le 34 VIII Entretien Maintenance cccceccecececceeeceeeevecseeeuacseeeuaceeeeuaeeneevavseenvareeenvareeuevarenenvarenenvarenentas 36 Installation commissioning and operating instructions SYCLOPE TERE O General Page 4 40 I General 1 Field application The analyser controller of the SYCLOPE TERE O range you have just purchased is an electronic swimming pool water management device
20. ent according to the environment The SYCLOPE TERE O electronic box should not be installed in a hazardous environment and should be protected against splashing with water or chemical products It should be installed in a dry well ventilated location isolated from corrosive vapours Installation commissioning and operating instructions SYCLOPE TERE O Environment and safety instructions Page 9 40 A A JOO Make sure that the chemical sensors used with this device correspond well to the chemicals used Refer to the individual technical note of each sensor Chemistry of water is very complex in case of doubt contact immediately our engineering service or your approved installer reseller Chemical sensors are sensitive elements using consumable parts They must be supervised maintained and calibrated regularly using specific calibrator systems not provided with this equipment In the event of defect a surplus possible hazard of chemical injections can be noted In the doubt a service contract must be taken near your reseller installer or failing this near our engineering services Contact your approved installer reseller or our business service for more information 4 Q Identification and localization of the identification plate 2 O D LLI TERF O s N 151909989 oo gt ref TER 0000 A T J 90 240VAC 50 60Hz Phones 10 2 0 16A 4 D z iy IP65 C a ee ete ee www syclope fr Made in Fran
21. er 1 As the left part the right part uses the Mode key to access the menu of measured parameter from E2 entry In this case navigation is performed using M OK and ESC key of the right part of the display affected to parameter 2 gt Choice of the sensor The modification of the sensor is only possible if you press START STOP key when starting the controller Once the sensor is chosen and the controls started the choice of sensor is deactivated again The access to the choice of sensor is performed by pressing OK when Sensor line is selected in intensified brightness The keys allow to select the registered sensors Once the sensor chosen use OK key to validate the choice In any time it is possible to leave this menu without validating the choice by pressing on ESC key gt Alarm thresholds The access to alarm thresholds sub menu is performed by pressing OK when Alarms line is selected in intensified brightness The following sub menu appears Previously by pressing on and keys allow to set the highest alarm threshold corresponding to the parameter Then done press on OK key to validate the high value Once the high threshold validated use and keys to set the lowest alarm threshold and press OK to validate the low value In any time it is possible to leave this menu without validating the alarm thresholds by pressing on ESC key gt Choice of control mode The access to the choice
22. ered relay outputs P1 and P2 Powered relays Max 5A 250VAC Inrush current Max 15A lt ims REF 12VDC power output for supplying converters or external REF flow switch sensors Communication port RS485 1 RS485 communication port with compatible ModBus RTU DS protocol Protection of powered outputs internal tices Glass fuse 5x20mm 5A 250V fast FUSF1 Glass fuse 5x20mm 5A 250V fast FUSE2 Main functions Page 12 40 2 Main functions Function Marker s Control from 0 to 100 Mode of control Proportional Cycle time 240s Actuator type Powered relays 90 240VAC 5A PWM command Direction Expressed in real measurement values Alarms Low and high alarms Threshold controls up and down Closed loop control of injections with an Closed loop control Flow switch control external contact filtering for example or with control of water circulation Configuration Std configuration Automatic selection of parameters Maintenance Maintenance program Internal test program procedures 3 Parameter and scale of measurements Measures and controls T C 0 5 pH 0 5 Redox ORP 0 5 RAA 0 5 0 5 E 0 5 0 5 a Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 13 40 IV Installation and wiring 1 Installation conditions To guarantee user safety and ensure correct operation of your SYCLOPE TERE O please observe the following ins
23. essage is displayed That means that the sensor is still in operating condition but must be replaced soonest If the system detects that the last calibration point is too far away from the theoric value the sensor calibration is cancelled and Calibration ERROR message is displayed That means the sensor is working bad or is broken Please replace it immediately Installation commissioning and operating instructions SYCLOPE TERE O Maintenance Page 36 40 VIII Maintenance The controller is without maintenance Repairs must be carried out only by qualified technicians and must be carried out in our factory of SAUVAGNON For any problem concerning the controller or councils about water treatment do not hesitate to contact our after sale service Installation commissioning and operating instructions SYCLOPE TERE O Certificat CE Page 37 40 Designation of the products TEREO Declaration SYCLOPE Electronique SAS Z I A ropole Pyr n es in SAUVAGNON France hereby certifies by the present that the following models UNIS EAU and INDIG O controllers for the analysis and controls of physicochemical measurements are in conformity with the standards and safety as defined by the European directives 2006 95 EC Low voltage directive 2004 108 EC Electromagnetic compatibility and 2002 95 CE RoHS directive The present declaration is valid for all of the specimens manufactured after the date of this
24. for chlorine parameter and a hysteresis value of 10 the differential value will be Fs Hy 10 x 10 x 1 100 either 1ppm If the set point is 2ppm the dosage will be activated between 1 5 and 2 5ppm 224 C Sensor Alarms Control e Direction Growing Period time Calibration PELUS Sensor Alarms Control Direction e Period time 120s Calibration PELS Capteur Alarmes R gul Dosage Pa sep Pear CIT d 7 20 Dur e cycle eCalibration i M es 0 15 gt Direction of control The access to the direction of control is performed by pressing OK when Direction line is selected in intensified brightness The following sub menu appears By pressing on and keys allow to select Growing or Decreasing direction corresponding to the control of parameter In any time it is possible to leave this menu without validating the proportional band by pressing on ESC key gt Period time setting The access to the period time of control is performed by pressing OK when Period time line is selected in intensified brightness The following sub menu appears Setting of the period time is allowed by using 48 and keys to adjust it between 10 to 240 s When done press OK to validate the value In any time it is possible to leave this menu without validating the cycle time by pressing on ESC key gt Calibration of the offset pH7 of the sensor The access to the of
25. fset ph7 calibration sub menu is performed by pressing OK when the Calibration line is selected in intensified brightness and OK again when the offset lines appear with a value to be adjusted for calibrating zero of amperometric sensor and of pH 7 for pH sensor Measurement value of the parameter appears on Mes line By pressing on and keys allow to set the reference value When the good value is entered press OK key to validate Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller 7 7 ni o C Sensor Alarms Control Direction Period time e Calibration 22 4 C Capteur Alarmes R gul Dosage Dur e cycle eCalibration RAZ OK Esc Page 32 40 gt Calibration of the gain or pH4 of the sensor The access to the Gain ph4 calibration sub menu is performed by pressing OK when the Calibration line is selected in intensified brightness and OK again when the Gain lines appear with a value to be adjusted when away of 0 value for calibrating gain or slope of amperometric sensor and of pH 2 to 6 and pH 8 to 12 for pH sensor Measurement value of the parameter appears on Mes line By pressing on and keys allow to set the reference value When the good value is entered press OK key to validate gt Resetting calibration The access to the resetting calibration sub menu is performed by pressing OK when the Calibration l
26. gher display part gives informations about E3 and E4 entries and P1 and P2 relay outputs The value B displayed in the left higher corner indicates the temperature The symbol informs that the water does not circulate into the measuring chamber The symbol informs that the P1 output is activated The symbol 4 informs that the P2 output is deactivated Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller Page 34 40 4 Polarisation of sensor When starting the controller or when connecting of a new sensor the symbol El will appear This symbol indicates that the polarization of the sensor is in progress During this programmed time fixed at 2 minutes the regulation if it is launched is put in pause mode symbol LL During this period it is impossible to reach adjustments or calibrate the sensor By pressing on CALIB key allows to inhibit the polarization time of the corresponding sensor 5 Calibration of the sensors The CALIBRATION key allows to carry out a calibration of the sensor with who s connected on E1 or E2 entries with only one reference value Calibrations are determining operations for good working of the controller and best treatment of the swimming pool A bad calibration could be dangerous for your health and your swimming pool It can cause corrosions and destruction of the swimming pool parts In any doubt about the procedure contact our after sale service A ba
27. her at the agency or at the office for your region or country or the technical quality departments of our establishments We will do everything in our power to help you and ensure you benefit from our advice and know how in the field of measurement and treatment of Swimming pool water Contact Service technique syclope fr Installation commissioning and operating instructions SYCLOPE TERE O General Page 5 40 2 FCC conformity The SYCLOPE TERE O controller complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference 2 this device must accept any interference received including interference that may cause undesired operation FCC Regulations state that unauthorized changes or modifications to this equipment may void the user s authority to operate it This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or tele
28. ine is selected in intensified brightness and OK again when the RAZ line appears By pressing on OK key will reset all calibration of the corresponding parameter In any time it is possible to leave this menu without reset by pressing on ESC key Be careful This operation is irreversible Once validated by OK key all your personal configuration parameters will be lost c Screens of measurements and dosing in progress This screen is the operational screen of your controller It is composed of three parts gt Left part corresponding to the measured parameter on EL entry gt Right part corresponding to the measured parameter on E2 entry gt High band part giving various operating information gt Displaying the measurement value The measured value is displayed according to the range of the selected sensor This field can take four different statutes Jp Measured value Value higher than the range of the sensor vee Value lower than the range of the sensor Ea Unconnected sensor gt Displaying setting point The symbol EXIM represent the setting point value Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller Page 33 40 This last one is programmable directly from the main screen by using 8 and keys corresponding to the parameter Validate by pressing OK key If the modification is not validated before 5s it will not be registered gt
29. makes it possible to get out immediately Configuration e Language Contrast Flow switch E4 Calibration Temp Temperature display Factory settings Communication V X XX Sn XXXXXXXXX Configuration e Language French Contrast Flow switch E4 Calibration Temp Temperature display Factory settings Communication V X XX Sn XXXXXXXXX Configuration Language e Contrast 50 Flow switch E4 Calibration Temp Temperature display Factory settings Communication V X XX Sn XXXXXXXXX The keys O and D allow to navigate in the menu The Pok key allows you to confirm your choice The LES key allows you to leave the configuration menu gt Language By pushing on OK key whereas the line Language is in intensified brightness allows to have access to language selection The and keys allow to show the available languages The validation is done by pushing OK key In any case it is possible to return to the previous state without validation by a short pushing the ESC key gt Contrast By pushing on OK key whereas the line Contrast is in intensified brightness allows to have access to adjust contrast value The and keys allow to increase decrease the contrast value in real time Once desired contrast is reached the validation is done by pushing OK key In any case it is possible to return to the previous state without validation by a short pushing the ESC key Installa
30. ning Page 25 40 VI Commissioning You have just carried out electrical connections you have installed sensors and you have connected dosing equipments you are thus ready to carry out the startup of your SYCLOPE TERE O controller Apply the power supply on the controller A Check if no visual problem appear if the controller is well lit and if the other equipments of the installation are not disturbed SYCLOPE TERE O controller does not launch automatically the chemistry treatments The user is the main master for launching the controller after checking the good programation according the needs SYCLOPE TERE O is full programmable During the power up the preset parameters are fixed and all regulation processes are inactive user to modify this programming if it does not correspond to the needs To modify the SYCLOPE TERE O controller is delivered with standard programming It is advisable for the programming of the controller please refer to the following chapter VII Programming the controller The TERE O controllers are equipped with a keyboard and a LCD display to establish the dialog between the user and the machine ge Ensure the good programming of the TERE O controller before starting regulations amp 9 An excess of chemical products can cause harmful actions on the human health and the environment 1 Keypad and LCD display The LCD display is a 128x128 dots matrix with blue back light and white w
31. ns and destruction of the swimming pool parts In any doubt about the procedure contact our after sale service Ge A bad setting point could cause excessive consumptions of calories and harm the 9 environment By pressing on OK key whereas the line Calibration Temp is in intensified brightness allows to have access to the temperature sensor calibration This calibration procedure use only one point The and keys allow to adjust the measured value to the real value of the temperature The validation is done by pushing OK key If the calibration procedure is correctly proceeded the Calibration OK message is displayed If the system detects that the last calibration point is a little bit away from the theoric value the temperature sensor calibration is done but a Calibration LIMIT message is displayed That means that the temperature sensor is still in operating condition but must be replaced soonest Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller Configuration Language Contrast Flow switch E4 e Calibration Temp 22 C Calibration ERROR Temperature display Factory settings Communication Configuration Language Contrast Flow switch E4 Calibration Temp e Temperature display ON Factory settings Communication V X XxX Sn i XXXXXXXXX Configuration Language Contrast Flow switch E4 Calibration Temp Temperature display
32. of control mode sub menu is performed by pressing OK when Control line is selected in intensified brightness The following sub menu appears The and keys allow to select PROP mode for proportional control or HYST mode for a control by hysteresis Once the control mode is chosen use OK key to validate In any time it is possible to leave this menu without validating the alarm thresholds by pressing on ESC key Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller FEU Sensor Alarms Direction Period time Calibration Page 31 40 gt Setting of proportional hysteresis band The access to the proportional hysteresis band setting sub menu is performed by pressing OK when Control line is selected in intensified brightness The following sub menus appears By pressing on and keys allow to set the proportional band corresponding to the parameter In any time it is possible to leave this menu without validating the proportional band by pressing on ESC key Proportional band Bp is understood as of full scale Fs That means for a pH full scale of 0 to 14pH and a proportional band of 10 the dosage value will be 100 when the gap with the setting point will be gt to Fs Bp 14 x 10 x 1 100 either 1 4pH Hysteresis Hy is understood as of full scale Fs centred on the set point That means for a full scale of O to 10ppm
33. ommissioning and operating instructions SYCLOPE TERE O Installation and wiring Respect polarities and connections of the bus e A terminal to signal AA n 3 of USB RS485 converter e B terminal to signal BB n 4 of USB RS485 converter C terminal to GND n 5 of USB RS485 converter Page 22 40 To connect TERE O controller to a PLC or a laptop we recommend to use a specific USB RS485 converter Please refer to the communication Manuel for wiring and programming Reference Name INF1021 Interface converter USB amp 485 O Refer to the Communication Manuel for more informations about all possibilities of connection Installation commissioning and operating instructions SYCLOPE TERE O General use Page 23 40 V General use SYCLOPE TERE O controller is intended to measurement and to control parameters for water treatment of swimming pools This equipment can be use under two different fundamental principes described below gt Measurement of parameters come from the gravitating return line gt Measurement of parameters come from the recirculating filtration circuit 1 Measurements come from gravity return line This type of installation is recommended when more swimming pools are connected only to one buffer tank and one block of filters Swimming pool Dosing pumps Heater Buffer E Measuring cell on return pipe Circulation pump e Water is sampled
34. on Calibration Temp Temperature display Factory settings e Communication This window also allows to verify the connection statute of the socket modem when activated V X XX SN XXXXXXXXX a By using and keys allow to select the parameter to be modified when Parity oo de Adress the desired parameter is in intensified brightness Press on OK key to Protocol enter in modification mode In modification mode line blinking the 48 and keys allow to modify the Modem No Modem To validate press OK key To cancel and to return to the previous menu press ESC key Installation commissioning and operating instructions SYCLOPE TERE O Programming the controller Page 30 40 D For more information refer to the communication manual of the controller Manual 2 b Setting parameter values PEI Pagi Peger e Sensor Alarms Control Direction Period time Calibration an Ti a 22 4 C e Sensor Cl 10ppm Alarms Control Direction Period time Calibration 22 4 C Sensor e Alarms A 1 50 Control Direction Period time Calibration 22 4 C Sensor Alarms e Control Prop 10 Direction Period time Calibration By pressing long time on Mode key of the left part gives access the menu of the measured parameter from E1 entry In this menu navigation is performed by using OK and ESC keys on the left part of the display affected to paramet
35. ranting the good working of the sensors No claim will be accepted if these conditions were not respected __ Sensors E 1 EH EI e El Parameter 1 entry Displayed on the left part of the screen e E2 Parameter 2 entry Displayed on the right part of the screen e E3 Temperature entry Displayed on the superior band of the screen Flow switch Violet Grey Installation commissioning and operating instructions SYCLOPE TERE O Installation and wiring Page 19 40 b Direct entries with internal modules version power supply This entry is dedicated to the temperature measurement using a 4 20mA SYCLOPE Electronique sensor Only E3 is a not isolated self powered 12V entry and must be used without external ____ Sensors o oo Lals sts 213 According the controller version 1 or 2 BNC connectors could be implanted near the electrical glands These connectors are wired directly to the internal entries El or and E2 In this configuration E1 E2 and E3 entries are affected by the factory and must not be changed e Ei pH entry BNC Displayed on the left part of the screen e E2 Chlorine or Bromine or Redox BNC entry Displayed on the right part of the screen e E3 Temperature entry Displayed on the superior band of the screen a e emt me 6m Some Bromine T C pH Chlorine Terminal E3 BNC E1 Terminal E2 T C pH
36. riting By internal software the screen is separated as follow e The higher part indicates the temperature measurement entry E3 the state of switch control E4 and the states of P1 and P2 relays e The left part indicates the measurement values controls and alarms of the parameter connected on E1 entry e The right part indicates the measurement values controls and alarms of the parameter connected on E2 entry The keypad is symmetrical The left part of the keyboard gives access to the adjustments of the parameter selected on the left part of the LCD display The right part of the keyboard gives access to the adjustments of the parameter selected on the right part of the LCD display HMI interface Page 26 40 TERE O 1 AC by AL paie T LGN P SEF 15 1x t 0 40 6 7 20 1 00 5 3 0 30 9 aE 6 51 START Wate OK key a short push allows the validation of the operation ESC key a short push allows erase or return to the preceding operation A long push gives you access to the general menu of the controller A Key a short push makes it possible to move into the menus or to increment a value A long push allows a fast increment of a value Key a short push makes it possible to move into the menus or to decrement a value A long push allows a fast decrement of a value G daB Calibration Key a short push allows the calibration of the corresponding sensor A long push allows the inhibition
37. tallation instructions Install the controller in a dry location The controller must be protected against rain frost and direct sunlight The room temperature must range between 0 C and 50 C with no condensation Choose an installation location free from vibration on a suitable support and with no deformation If these instructions are not observed gt The controller is at risk of being damaged gt The measurements can be disrupted gt The warranty is not applicable VV VV 2 Installation of the wall mounted controllers Before performing the installation and electrical connections remember to turn off the power AN The rating of IP65 is only guaranteed when the closing cover and the glass of the electric box are closed and when the cable glands match the diameters of your cables and are correctly sealed gt Drilling three holes 5 mm according to the following drilling plan 198 01 gt Insert the 5 mm plugs using a hammer gt Insert the upper screw top screw first without completely tightening it gt Insert the lower screws and tighten them gt Tighten the upper screw gt Use a spirit level to check for correct and accurate fixing to the wall Installation and wiring Page 14 40 3 _Opening Closing the transparent door To ensure IP65 protection class the transparent door must be closed after usage and being sure of the O ring quality each time The controller box is equipped with an
38. the SYCLOPE TERE O controller is designed in compliance with the restrictions on hazardous substances According to low voltage directive 2006 95 EC and the electromagnetic compatibility directive 2004 108 EC this symbol means that the device has been designed in compliance with the previously cited directives In accordance with part 15 of the FCC regulation Federal communications commission this symbol indicates that the device was tested and approved under the respect and the conditions of the limits for a Class B digital device Installation commissioning and operating instructions SYCLOPE TERE O Technical characteristics Page 11 40 III Technical characteristics and functions 1 Technical characteristics General characteristics Type Marker s Consumption Power supply required Electric protection F4 Operating temperature C Storage temperature C 10 C to 70 C 10 F to 158 F Humidit Case material Length 213 mm 8 4 inches Case dimensions Width 185 mm 7 3 inches Height 118 mm 4 6 inches Weight of the case 1 1 Kg Protection rating IP 65 Displa Screen LCD 128x128 with back light White blue 4x 0 4 20mA auto powered entries 12V without isolation within Measurement inputs 2x programmable modules internally soldered e 4 20mA isolated module powered by 24VDC max e pH isolated module Range 400mV to 400mV e Redox isolated module Range 0 to 1000mV Powered outputs 2x Pow
39. thout electrical power cable The pre holes of the box are drilled and equipped with according electrical glands in compliance with IP65 level protection Cables must be adapted to the electrical glands to respect the level of protection Grounded cables for connecting pH and ORP Redox sensors are not provided Content of the packaging v One analyzer controller SYCLOPE TERE O v Installation and starting instruction notice v Programming notice Communication notice Option 7 Warranty The warranty is provided according to the terms of our general conditions of sale and delivery as long as the following conditions are met gt Use of the equipment according to the instructions of this notice gt No modifications of the equipment which may modify its behavior and no incorrect manipulation gt Respect for the electrical safety conditions D Consumable material is no longer covered by the warranty when in use Installation commissioning and operating instructions SYCLOPE TERE O Environment and safety instructions Page 8 40 II Environment and safety instructions Please gt Read this manual carefully before unpacking installing or commissioning this equipment gt Take into account all the hazards and recommended precautionary measures Failure to respect these procedures can result in serious injury to users or damage the device 1 Use of the equipment The SYCLOPE TERE O system has been designed to me
40. tion commissioning and operating instructions SYCLOPE TERE O Programming the controller Configuration Langue Contrast e Flow switch E4 NO Calibration Temp Temperature display Factory settings Communication V X XX SN XXXXXXXXX Configuration Language Contrast Flow switch E4 e Calibration Temp 22 C Temperature display Factory settings Communication Configuration Language Contrast Flow switch E4 e Calibration Temp 22 C Calibration OK Temperature display Factory settings Communication Configuration Language Contrast Flow switch E4 e Calibration Temp 22 C Calibration LIMIT Temperature display Factory settings Communication Page 28 40 gt Flow switch E4 By pushing on OK key whereas the line Flow switch is in intensified brightness allows to have access to select the polarity of the circulation flow switch The and keys allow to select the state of the recirculation flow switch NO normally open or NC normally closed Once the good value is selected the validation is done by pushing OK key In any case it is possible to return to the previous state without validation by a short pushing the ESC key gt Calibration temperature Calibrations are determining operations for good working of the controller and best treatment of the swimming pool A bad calibration could be dangerous for your health and your swimming pool It can cause corrosio
41. vironment and safety ProCeCures cccscsscsecsccsecnccnceecnecnseeenscnesesescneaneesonsesstsnseneatsnsneansenons 8 1 WSC OF TNE JEG UIDIMENE SR RE RS RS Store 8 2 MISCO IONS tics de na an cu ies a nee we oi ci den ees 8 3 RISK DPE VEMUOM EST a Net era E musta os ee nest ins diet 8 4 Identification and localization of the identification plate cccecceecseseeeeeeeeeeeeeeeaeeeeseeaeeaeeeeaess 9 5 DISDOSAl and CON TONNES Se cn E nan eos ir tant 10 III Technical characteristics and TUNCtIONS 3 nr nee nn 11 Ly SECCHNICAl characteristics en tatmaeease anaes an ren nn ee nr 11 2y Main UCHOD S SR nn ie a nt ct 12 5 Pararmeter and scale Of measurements ist siemens ia tenenrnra trae ene 12 IV Installation and WING ses RS Se nd sn dan set teens ere nee ions ess rn 13 1 Installation COMGITIONS SE 13 2 Installation of the wall mounted controllers Re 13 3 Opening Closing the transparent door ccccscsecsecsececcecseeeecneaeceeoneaesesonecnsatseecnserseeonsensetsnes 14 4 Openihig Closing CONNECTION COVEr ser ice mien limiter rincer er ir 14 De Fl triCol CONNECTIONS ESS a 15 6 Changing internal fuses of P1 and P2 outputs ssssssenenenenoneneneneusenenenenenenenenenenenensososonononene 15 7 Conn ching primary p wer SUDDIV snif een pen este a aan tagausessesaeageroann 16 8 Connecting the self powered relay P1 cccsccscescceceesnececaeenecncaecnecneatsesoneanseesnsnsarsneensansn
42. vision reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect this equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes and modifications not expressly approved by the manufacturer could void the user s authority to operate this equipment Remark To ensure compliance with the FCC regulations on electromagnetic interference for a class B device use cables properly shielded and connected to the ground as recommended in this manual The use of a cable that is not properly shielded or earthed for risk of violating the FCC rules Installation commissioning and operating instructions SYCLOPE TERE O General Page 6 40 3 Utilisation du document Please read this entire document before starting to install adjust or commission your device in order to ensure the safety of swimmers users and equipment The information provided in this document must be strictly observed SYCLOPE Electronique S A S declines all responsibility in cases where failure to comply with the instructions of this documents is observed The following symbols and pictograms will be used to facilitate reading and un
Download Pdf Manuals
Related Search