Olympus OM-1 Service Manual Part 4 of 4
Contents
1. PARTS WHERE OIL GREASE ETC SHALL BE USED OLYMPUS OPTICAL CO LTD F 1 LOCKTITE Cement ARALDITE CEMEDINE Cement Tyr ttr TR T ALON ALPHA Cement Pm com terme PLIOBOND Cement F 6 PLIOBOND Cement v 7 PLASTILUBE Grease COSMORUBLIC Oil OILPROOF FLUID PHOTOLUB Grease MOLYKOTE 55 B PHOTOLUB Grease OP 4 a m Ger M o SPECIAL TOOLS OLYMPUS OPTICAL CO LTD Gl SPECIAL TOOLS KC CA8752D Wrench To be mounted onto Q 0009M Diam 6mm Holder for use Tobe used in dismantling CA8752 Cap and CA9135 Plate 071 Wrench To be used in removing CA8733 Shaft and CA8725 Knob Pinch holding the R Shaft from outside turn the Knob KC CA9030G Wrench be mounted onto Q 0008M Diam 3 2mm Holder and to be used for mounting or removing CA9030 Nut KC CA9071G Wrench To be mounted onto Q 0008M Diam 3 2mm Holder and used for mounting or dismounting CA9071 Stop per 2 3 KC 0070G 01 For measurement of flange back 46 00 for 1 in the Mount Stage same manner as for Models FTL and FT Place KC 0070G 3 on top of 1 and set the 0 KC 0070G 03 Zero position Measurement 2 Remove 43 and mount the camera body onto 1 Gauge 3 Me2. asure the rail surface by the dial gauge discrepancy between the 0 Zero position should be within 020 02 46 00 36 8 KC 00T0G KC CA8788G Wrench KC CA8408G Positioning Tool G 4 To be mounted ont Q 0009M Diam 6mm Holder and used for mounting or dismounting CA8788 Gear e 7 6 2 F 4 N y Distance between the Fresnel surface of CA8702 Plate and the L pin and its measurement 0 Place CA8702 upside down on the measuring stage with its Fresnel surface pressed against the stage 2 Set the A surface of the stage at the O position on the dial gauge 3 Slightly move the measuring stage measure the height of the L pin and take the reading of the difference which should be within 00 05mm 5 5310 05 G 5 KC CA8843G To be mounted onto Q 0009M Holder and used for Wrench mounting or dismounting 8843 Shaft onto 8501 Plate gt Remarks Do not touch both 028843 and 8501 with bare hands KC 0072G To be mounted onto CA8944B String and used for inspection Poise for CA8944B and adjustment of the CA8879 Ring String KC CA133 G Wrench canta _ 0073 Pase NE KC CA8777G Wrench G 6 Use by inserting into Q 0008M Adjust tension by turning Parts No CA8531 48 2 Use only to support lenses on repairing Larger dia for OM lenses and smoller for lenses of PenFT amp FTL U
3. outact point Circuit Diagraph EN H 3 IMPROVED PARIS TABLE E Diag A New 2 7 Diag B Old 6 h Wire Diam 0 45 Three Parts CA9153 CA9154 amp 9156 Shown left page are added recently 4 carros Aluminum Diewsest _
4. se by inserting into Q 0009M Use for Parts CA8777 G 7 KC 0074G Positioning 1001 How to use How to check Use for Check of positions of connecting ring CA8879 connecting lever CA8425 and Mirror releasing Mirror Mount KC 0074G and B mount by according index of KC 0074G outer circuit and that of B mount Shutter speed setting position 1 Position of Connecting ring 8879 Pull down A towards you and chek if scratched line of A returns between two scratched line of B 2 Position of Connecting lever CA8425 a Stop position of 425 should be in this range b After shutter charging position of CA8425 should be this range C Before shutter charging position of CA8425 should be this range d X direction of optical axis e Y direction right amp left of CA8425 should be positioned around this vertical scratched line e Position of Mirror releasing Set shutter speed at 1 4 and charge Make mirror up a little by tuming mirror up knob Push down shutter release button with but at this time hold the mirror frame with your forefinger of right hand not to make shutter release Lifting up the mirror frame with forefinger shutter should be released when the mirror frame is positioned in this range Circuit Diagraph FP 2 Exposure meter Circuit Diagraph Man SW Synchro c
Download Pdf Manuals
Related Search