Installation Manual
Contents
1. rOSSLWN w SECURITY PRODUCTS Installation Instructions SA 02 Supervised Wireless Magnetic Contact Sensor 1 General Description The SA 02 Supervised Wireless Magnetic Contact Sensor is a high performance intrusion sensor developed with the highest level of technology to make it ideal for residential and commercial applications 1 1 Standard Features e Supervisor e Case and Back Tamper Detectors 2 Technical Specifications 2 1 Electrical Characteristics Battery Lithium Primary cell 3 6 volt Lithium 900 mAh Tadiran Varta Tekcell SB AA 02 1 2 AA Size Low Battery Signal when V 2 5V CAUTION Dispose of propeny Do not recharge disassemble heat or incinerate Current Standby 23 uA Transmit 5 mA Pulse Count Fixed at single pulse Detect Range Sensitivity of up to 2 cm from magnet Alam Transmit One second 2 2 Environmental Characteristics Operating Temperature 20 C to 50 C 4 F to 122 F Operating Humidity Up to 95 non condensing max RF Frequency Available in 433 92 MHz or 868 35 MHz with lm Watt e ASIC and Microprocessor Technology e Up to 3 yr battery life with SPS e Ultra low current consumption e Readily replaceable 3 6V 1 2 AA Lithium battery e SMD component technology e LE D Test Function Installation Indoor Magnet Standard magnet with plastic housing and wall spacer adjustable height Tamper Switch 1 Detects removal of Magnetic Contact Sensor Fron2. defects in materials and assembly in the course of normal use and service The warranty period commences with the date of shipment to the original purchaser and extends for a period of 2 years 24 months Warranty Remedy Coverage In the event of a breach of warranty ROSSLARE will credit Customer with the price of the Product paid by Customer provided that the warranty claim is delivered to ROSSLARE by the Customer during the warranty period in accordance with the terms of this warranty Unless otherwise requested by ROSSLARE ENTERPRISES LTD AND OR SUBSIDIARIES representative return of the failed product s is not immediately required If ROSSLARE has not contacted the Customer within a sixty 60 day holding period following the delivery of the warranty claim Customer will not be required to return the failed product s All returned Product s as may be requested at ROSSLARE ENTERPRISES LTD AND OR SUBSIDIARY S sole discretion shall become the property of ROSSLARE ENTERPRISES LTD AND OR SUBSIDIARIES To exercise the warranty the user must contact Rosslare Enterprises Ltd to obtain an RMA number after which the product must be returned to the Manufacturer freight prepaid and insured In the event ROSSLARE chooses to perform a product evaluation within the sixty 60 day holding period and no defect is found a minimum US 50 00 or equivalent charge will be applied to each Product for labor required in the evaluation Rosslar
3. the Magnetic Contact Sensor case isclosed with the locking screw firmly secured 2 Hold the sensorasclose aspossible to the mounting location and transmit using the magnet 3 During thismode each time the LED flashes the sensor transmits to the panel If the panel isarmed an alam isactivated If the panel isin test mode the signal strength can be measured 4 Itisrecommended to try several locations until the best reception is attained 4 7 Mounting the Magnetic Contact Sensor The SA 02 Magnetic Contact Sensor is designed to be mounted onto a flat wooden or stucco surface 1 Remove the PCB from the backcase 2 Remove the knockouts from the back case labeled B by using a sharp tool orusing a nail 3 Affix the two screws onto the wall so that the Back Tamperamn is pressed in 4 Replace the PCB and tighten the PCB locking screw 5 Replace the top coverofthe Magnetic Contact Sensor Note When mounting the SA 02 to the surface it is important to see that the surface is flush with the back tamperdevice l2 Ni n LAU ech Figure 6 Mounting the SA 02 0706 0960238 00 ROSSLN Y SECURITY PRODUCTS 4 8 Post Installation Testing After mounting the back of the sensor housing to the window ordoor frame it is important to check the reliability of the RF transmission to the receiver or secunty panel 1 Performa range test as indicated in section 4 6 If the sensor is used with a receiver check
4. NTY SHALL BECOME NULL AND VOID IN THE EVENT OF A VIOLATION OF THE PROVISIONS OF THIS LIMITED WARRANTY 6 Technical Support Asia Pacific Middle East Africa Headquarters 905 912 Wing Fat Industral Bldg 12 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2795 5630 Fax 852 2795 1508 E mail support a pa c rosslaresecurnty com United States and Canada 1600 Hart Court Suite 103 Southlake TX USA 76092 Toll Free 1 866 632 1101 Local 1 817 305 0006 Fax 1 817 305 0069 E mail support na rosslaresecunty com Europe Global Technical Support amp Training Center HaMelecha 22 Rosh HaAyin Israel 48091 Tel 972 3 938 6838 Fax 972 3 938 6830 E mail sup port eu rosslaresec unty com South America Pringles 868 1640 Martinez Buenos Aires Argentina Tel 54 11 4798 0095 Fax 54 11 4798 2228 Web Site www rosslaresecunty com 0706 0960238 00
5. and vibration effectson the sensor and extends the life of the product 3 Perform the RF Test from the proposed mounting location to ensure that the sensorcan be received 4 Select the appropnate height forthe magnet assembly that suits the location of the sensor Mount the 402 onto the stationary door trame Mount the Magnet Connect additional onto the door external contacts by wire to the A42 000000 OOOOoOoO HEHE 4 Figure 2 Selecting a Location 4 3 Selecting the Magnet Height The SA 02 comes equipped with a standard magnet of adjustable height suitable for most applications When there isa mismatch in height between the door and the frame simply press on the sides of the mechanism on the magnet to adjust the height of the magnet assembly to suit the location of the sensor Figure 3 Magnet 4 4 Wiring the External Sensor When the intemal magnetic sensor in the SA 02 is not applicable oran additional set of contacts isneeded for the SA 02 you can installa remote extemal magnetic contact sensor to the SA 02 with a wire using the following procedure Note The maximum distance between the extemal contact and the SA 02 is about 8 5 meters or 25 feet 1 Remove the case locking screw and front cover 2 Connect the extemal magnet s in seres to the wired input terminal block of the magnetic contact sensor 3 Move the jumper coverto the two rght most pins to activate the extemal magn
6. e will repair or replace at its discretion any product that under normal conditions of use and service proves to be defective in material or workmanship No charge will be applied for labor or parts with respect to defects covered by this warranty provided that the work is done by Rosslare or a Rosslare authorized service center Exclusions and Limitations ROSSLARE shall not be responsible or liable for any damage or loss resulting from the operation or performance of any Product or any systems in which a Product is incorporated This warranty shall not extend to any ancillary equipment not furnished by ROSSLARE which is attached to or used in conjunction with a Product nor to any Product that is used with any ancillary equipment which is not furnished by ROSSLARE This warranty does not cover expenses incurred in the transportation freight cost to the repair center removal or reinstallation of the product whether or not proven defective Specifically excluded from this warranty are any failures resulting from Customer s improper testing operation installation or damage resulting from use of the Product in other than its normal and customary manner or any maintenance modification alteration or adjustment or any type of abuse neglect accident misuse improper operation normal wear defects or damage due to lightning or other electrical discharge This warranty does not cover repair or replacement where normal use has exhausted t
7. etic contact input 4 Replace the front coverand locking screw fl Wired External Magnetic Contact Terminal Block for External Magnetic ct Jumper for activating the external contacts 4 5 Activating the Back Tamper Each SA 02 Magnetic Contact Sensor is equipped with both a Back and Case Tamper detector The Case tamper detector is always active however the wall back tamper detector nomally inactive canbe optionally activated for additional protection against the theft or removal of the sensor from the mounting location The back tampercan be activated to work in unison with the case tamper by cutting the jumper R18 which ison the top side of the PCB 1 Remove the case locking screw and front cover You can now see the front of the PCB with the antenna showing see Figure 5 2 Activate the back tamper switch by cutting the jumper 3 Replace the front coverand locking screw Jumper wire for activating the back tamper switch Cut the jumper R 18 to activate the back tamper Figure 5 Activating the Back Tamper 4 6 Performing Radio Transmission Test This test is used to check the range and reception of the sensor to the control panel receiver If reception is poor try to change the location of the Magnetic Contact Sensor 1 Ensure that all the settings of the Magnetic Contact Sensorare adjusted asnecessary forthe location according to the stepsin sections 4 1 to 4 5 and that
8. he front cover CAUTION Do not touch the magnetic element orthe electronic components inside as doing so may cause damage 2 Fora new unit simply remove the plastic strip contact breaker Forreplacement remove the battery using a small screwdriver CAUTION Notice the polarity Replace witha fresh battery 3 Dispose of the old battery propery Do not recharge disassemble heat orincinerate 4 To test depress both the back tamperand the case tamper buttons or use a magnet to simulate a dooropening and closing The LED lights up to indicate RF transmission 5 Close the front coverand replace the locking screw TERMINAL BLOCK FOR WIRED CONTACTS JUMPER FOR RF TRANSMISSION 7 INDICATION LED MAGNETIC CONTACT INTERNAL SENSOR BATTERY HOLDER CASE TAMPER UTT ON ANTENNA NORMALLY CLOSED A A Figure 1 Front of PCB 4 2 Selecting the Location The location and mounting of the SA 02 affects both the transmission range and the wearand tearof the transmitter Preferably the transmitter should be installed asclose aspossble to the receiver and mounted ina 0706 0960238 00 high location so that the transmission has less interference 1 Selecta DOOR or WINDOW within a room or hallway that best matches the cnitena in section 3 see Figure 2 2 Make sure that the Magnetic Contact Sensoris mounted on a sturdy non vibrating dooror window frame Note Following this instruction reduces bumping
9. he life of a part or instrument or any modification abuse of or tampering with the Product if Product disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection and testing to verify any warranty claim ROSSLARE does not warrant the installation maintenance or service of the Product Service life of the product is dependent upon the care it receives and the conditions under which it has to operate In no event shall Rosslare be liable for incidental or consequential damages Limited Warranty Terms THIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE ENTERPRISES LTD AND ITS SUBSIDIARIES WARRANTY THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON WHETHER OR NOT PURPORTING TO REPRESENT OR ACT ON BEHALF OF ROSSLARE THIS LIMITED WARRANTY IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED INNO EVENT SHALL ROSSLARE BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR FOR ANY OTHER INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF USE LOSS OF TIME COMMERCIAL LOSS INCONVENIENCE AND LOSS OF PROFITS ARISING OUT OF THE INSTALLATION USE OR INABILITY TO USE SUCH PRODUCT TO THE FULLEST EXTENT THAT ANY SUCH LOSS OR DAMAGE MAY BE DISCLAIMED BY LAW THIS WARRA
10. t Cover protected by case tamper switch Tamper Switch 2 Detects removal of Magnetic Contact Sensor from the wall orfrom comer mount protected by rear tamper switch Supervisor The supervisory signal is routinely transmitted to the panels every 20 minutes advising the Tamper Status Battery Status and Event Activation Status to the panel 2 3 Physical Characteristics Dimensions 87mm h x35mm w x25mm d 3 5 x13 8 x1 Weight 37 grams 1 30 oz without battery 3 Installation Performance Criteria The SA 02 Magnetic Contact Sensor detects the opening and closing of doorsand windows and transmits this information to the receiver panel e AVOID placing the Magnetic Contact Sensornear strong magnetic orelectrical fields other than the magnet with which it is intended to be used Otherwise performance may be affected and false alarms may occur e AVOID mounting on ornear large metal surfaces and multiple concrete steel walls as this may interfere or block the wireless signals Make sure to test the range from any location by using the RF Test Procedure to ensure reception NOTE Install the Magnetic Contact Sensor on windows or doors that have firm hingesand fim locking action to prevent false alarms associated with wind or bumping 4 Installation Instructions 4 1 Installing the Battery Use only the 3 6 V Lithium battery see battery specifications in section 2 1 1 Unscrew the case locking screw and remove t
11. to see that the receiver is receiving the sensor It is suggested that you am the system and test that the SA 02 transmits to the desired control panel Note If the back tamperhas been activated in previous steps check the security panel to ensure that there is no tamper signal and that the sensor is propery installed 4 9 Replacing the Battery in the SA 02 Batteries in the SA 02 should be replaced following a Low Battery indication on the receiver or secunty panel CE Caution Dispose of the old battery propery Do not recharge disassemble heat orincinerate 1 Open the SA 02 sensor and observe the corect polarity labeled on the PCB and the holder 2 Remove the old battery and dispose of it propeny 3 Insert the new battery according to the specifications in section 2 1 insart the NEGATIVE iia aide of battery rat Figure 7 Replacing the Battery 5 Limited Warranty ROSSLARE ENTERPRISES LIMITED S Rosslare TWO YEAR LIMITED WARRANTY is applicable worldwide This warranty supersedes any other warranty Rosslare s TWO YEAR LIMITED WARRANTY is subject to the following conditions Warranty Warranty of Rosslare s products extends to the original purchaser Customer of the Rosslare product and is not transferable Products Covered By This Warranty and Duration ROSSLARE ENTERPRISES LTD AND OR SUBSIDIARIES ROSSLARE warrants that the SA 02 Supervised Wireless Magnetic Contact Sensor is free from
Download Pdf Manuals
Related Search