IsatDock PRO User Manual
Contents
1. A WARNING DO NOT pull with force on the cables from the rear of the IsatDock PRO Please install strain relief clamping for the antenna cables where required Correct installation of the antenna system is a vital b700 part of the IsatDock PRO system to ensure reliable Directional Fixed Antenna functionality and drop free calls Passive with Bracket WARNING ISD715 Changes or modifications not expressly NY Magnetic approved by BEAM Communications could void Mounting the product warranty Transport Antenna WARNING Active Mounting To satisfy FCC RF exposure requirements for mobile transmitting devices a separation distance of 55cm or more should be maintained between the AN antenna of this device and persons during device operation To ensure compliance operations at NOTE closer than this distance is not recommended Refer to the section Antenna Installation for more information on antenna placement and installation Only Beam approved antenna cables should be used with all docking stations and antennas OBEAM 2a Wall Mounting Orientation There are nine screw holes available for mounting the bracket to a wall It is recommended that a minimum of 2 screws are used to ensure the docking station is mounted securely There are four keyhole shaped slots in the mounting bracket that mate2. accompanied by a long beep followed by three short beeps gt BEAM Configuration Using Remote Commands Configuration instructions or Remote Commands can be sent to the terminal via SMS and most settings are supported that are normally accessible from Falcon Please refer to the Falcon user manual for more information A NOTE Due to memory limitations it is recommended that users have no more than 20 SMS messages in their inbox If this amount is exceeded the processing of remote commands and the ability to retrieve the messages via the Falcon tool may be compromised IsatDock Key lock A barrel type lock is situated in the top of the dock When locked the eject button cannot be depressed and the latch holding the top of the handset cannot be disengaged from the IsatPhone Pro Once locked the access to the security bolt beneath the handset is also denied thus ensuring the PRO PRO docking station cannot be removed from the mounting bracket IsatDock PRO Installation amp User Manual 27 IsatDock PRO Front Panel Terminate call if speakerphone mode is active Activate speakerphone mode if Privacy Handset mode is active Out of Call Answer inbound call in speakerphone mode LED turns GREEN Speakerphone mode active Location Button Action LED Sound Mode Redial Out of Call oO 1 second Redial previous number dialed N A g
3. ISD932 6m cable kit Active ISD933 13m cable kit Active ISD934 18m cable kit Active ISD935 31m cable kit Active ISD938 40m cable kit Active ISD942 50m cable kit Active ISD943 60m cable kit Active ISD944 70m cable kit Active ISD945 80m cable kit Active ISD946 90m cable kit Active ISD947 100m cable kit Active Passive Antennas ISD700 Directional Fixed Antenna Passive Antenna Cable Kits for Passive Antennas ISD936 10m cable kit Passive ISD937 20m cable kit Passive ISD939 30m cable kit Passive ISD940 40m cable kit Passive ISD941 50m cable kit Passive Additional Accessories RST055 UPS Battery Pack See your service provider for pricing and availability of these quality BEAM accessories Additional Information For the latest in supporting software and documentation for IsatDock please contact www beamcommunications com support inmarsat Other Resources Available Online Advanced configuration inbuilt to Falcon Quick Start Guide amp Manual Antenna Installation Guide IsatPhone Pro firmware upgrade if required CONTENTS BEAM IsatDock PRO Part Number About Beam Communications Conventions in this Manual Terminology Package Contents Optional Accessories Additional Information Other Resources Available Online Safety Information Safety Transceiver IsatPhone Pro IsatDock FCC Information Electronic Devices Pacemakers Other Medical Devices
4. Vehicles Posted Facilities Aircraft Vehicles Equipped with an Air Bag IsatDock PRO Key Features Equipment Overview Installation Guidelines Routing Cables Guidelines for Electrical Connections Installation Procedure Installing the IsatDock PRO Cradle IsatDock PRO Usage Docking amp undocking the IsatPhone Pro handset Operation of the IsatPhone Pro Placing Voice Calls Privacy Handset Use Optional Accessory Mute Mode USB Driver Installation Configuration Using Falcon Configuration Using Remote Commands IsatPhone Key Lock IsatDock PRO Front Panel IsatDock PRO Installation amp User Manual 12 13 14 15 23 IsatDock PRO Buttons LED lights Assuring Quality of Service Specification Summary 31 Electrical amp Environmental Specifications lsatDock PRO 1 Physical Dimensions PRO Dock 2 Physical Dimensions Privacy Handset 3 Physical Dimensions Wall Bracket Trouble Shooting 33 Beam Warranty Conditions 34 IMPORTANT Please read the following information carefully before installing and using the IsatDock PRO Failing to follow instructions may compromise the safety of the product and may result in personal injury and or equipment damage Please consult your supplier if you have any further questions The IsatDock PRO is a low power docking station for the IsatPhone Pro handset When ON it will charge the IsatPhone Pro handset whilst docked in the IsatDock PRO Refer to the
5. appropriate section of this lsatDock PRO Installation amp User Manual for additional safety information Store the system in a cool and dry area Do not submerge the system in water Donot place foreign metal objects or debris in the system If debris enters into the system please return to factory for service A WARNING DO NOT open equipment There are no user serviceable parts inside Ifa DC power supply is to be used its output must comply with the Safety Extra Low Voltage SELV requirements of IEC60950 All connectors must only be connected to equipment ports which comply with the Safety Extra Low Voltage SELV requirements of IEC60950 POTENTIALLY EXPLOSIVE ATMOSPHERES Turn your phone OFF and DO NOT remove your battery or remove the IsatPhone Pro handset from the cradle when you are in any area with a potentially explosive atmosphere Obey all signs and instructions Sparks from your battery in such areas could cause an explosion or fire resulting in bodily injury or even death Areas with a potentially explosive atmosphere are often but not always clearly marked They include but are not limited to fuelling areas such as gasoline stations below deck on boats fuel or chemical transfer or storage facilities areas where fuel odors are present for example if a gas propane leak occurs in a car or home x areas where the air contains chemicals or particles such as grai
6. position 2 To remove the handset from the cradle press the EJECT button at the top of the docking station The dock will swing out and the handset can be removed Eject Button IsatDock PRO Installation amp User Manual A IMPORTANT Before docking the IsatPhone Pro to the docking station check that the USB cover is open able to swing free without putting it in a locked open position as illustrated in B and ready for docking at a 90 95 degree angle as shown on image C If not properly inserted this could cause some problems with the USB connection Operation of the IsatPhone Pro Prepare the Inmarsat IsatPhone Pro Ensure that the IsatPhone Pro Handset has the latest compatible firmware installed For more information visit http www beamcommunications com support pro Starting Up 1 Retract the antenna on the IsatPhone Pro handset 2 Place the IsatPhone Pro as per instructions Docking amp Undocking on page 23 3 Turn vehicle ignition on The IsatPhone Pro will automatically power and the handset will then start to initialise followed by a 3 tone rising beep when a successful connection has been made between the docking station and the IsatPhone Pro 4 Wait for the IsatPhone Pro handset to register on the Inmarsat network The STATUS LED on the docking station will turn green when a successful registration has taken place 5 You are now ready to make and receiv
7. the IsatDock interface power cable to power the unit until the full installation is completed latio n Proced Instal ure Installing the IsatDock PRO Cradle Install the components in the following order More detailed instructions can be found in the sections following 1 Install the external BEAM antenna 2 A Wall Mounting Orientation B Desk Mounting Orientation Connect the privacy handset amp cup Access to rear connector bay Connect POTS RJ11 Interface USB Port Connection Connect power cable OO SOY oO Cable routing 1 BEAM Antenna Connection The two external antenna connectors can be found in the cavity at the top of the IsatDock PRO cradle There are two RF connections required the Satellite TNC Female Connector and GPS SMA Female connector 1 Refer to the antennas installation guide for antenna mounting and location requirements 2 Connect the antenna cable labelled GPS to the SMA antenna connector labelled GPS 3 Connect the antenna cable labelled Inmarsat to the SMA antenna connector labelled ISAT 4 Connect the GPS SMA F cable end to the IsatDock s SMA connector n 5 Connect the TNC Female antenna cable end to the IsatDock s satellite connector IsatDock PRO Installation amp User Manual Anntena Connection Diagram Antenna connection image with Fixed Directional Antenna Passive SMA GPS 7 Satellite Antenna Antenna Cable Cable
8. the base of the dock while path C results in cables exiting to the side 22 ce 2 BEAM Optional through wall Right angled adapters are optionally fitted to the external antenna connectors to allow routing of cables through a wall A clean installation free of any visible cabling can be achieved with the use of right angled connectors and by running the interface cables along path A V r SMA Adaptor GPS TNC Adaptor GSPS IsatDock PRO Usage Docking amp undocking the IsatPhone Pro handset To place the IsatPhone Pro into the docking unit both the covers on the external antenna connectors and the USB Audio connectors need to be opened 1 The antenna cover must be placed at 90 degrees to the antenna connector cavity and run parallel to the top edge of the phone 2 The cover in the base of the phone should be in the a 90 degree opened position To dock the handset align the IsatPhone Pro with the phone tray and slide the handset down until it seats flush to the bottom of the tray Swing the phone down into the cradle by applying pressure to the top of the handset An audible click is heard when the phone is in the docked
9. with feet on the rear of the docking station To attach the bracket the larger end of the keyhole will pass over the feet The bracket is then slid up to lock the feet into the narrow section of the keyhole Security Bolts 2b Desk Mounting Orientation Two security bolts ensure the PRO docking unit The IsatDock PRO supports a desk mount is firmly fixed to the wall and only removed by an configuration Depending on the users authorized the security key holder personnel requirements the docking station supports both Once the IsatDock PRO is fitted to the wall a flat and raised orientation on the desk these two security bolts prevent the docking station from sliding back up freeing the dock To configure the IsatDock for a desk installation The security bolts are 4mm in diameter and have a 1 Fit the mounting bracket to the back of slot for a flat blade screwdriver the IsatDock as shown in section 2a wall The bolt under the privacy handset mounting mounting directions cup must be fitted prior to the cup being screwed 2 Flip the feet out if required and locate the into place The second bolt is placed under IsatDock on the desk the IsatPhone Pro in the recess for the handset antenna cover Both bolts are then covered with When desk mounting the security bolts are not plugs As the second bolt is under the IsatPhone required to be fitted Pro access to the bolt is denied when the handset is locked into the cradle Q Sl
10. 10 5W Sleep Mode 5mA 60mW Peak Current 3 5A 42W Physical Specifications Dimensions 270x 189 x 101 10 6x7 4x4 mm inches Weight dock 1 45kg 3 19lbs Total Kit Weight 2 45kg 5 39 lbs Environmental Specifications Operating Range 30 C to 70 C 22 F to 158 F Storage 35 C to 85 C 31 F to 185 F Battery Charging 0 C to 45 C 32 F to 113 F Temp Humidity lt 75 RH Connectors Interfaces POTS RJ11 RJ11 2 wire 5REN 600m Adjustable dial ring busy tone configured frequency and adaptive impedance BEAM Antenna TNC Female ISD700 Directional Fixed Antenna Passive ISD710 Transport Bolt Antenna Active ISD715 Transport Magnetic Antenna Active ISD932 6m SMA TNC cable kit Active ISD933 13m SMA TNC cable kit Active ISD934 18m SMA TNC cable kit Active ISD935 30m SMA TNC cable kit Active ISD938 40m SMA TNC cable kit Active ISD942 50m SMA TNC cable kit Active ISD943 60m SMA TNC cable kit Active ISD944 70m SMA TNC cable kit Active ISD945 80m SMA TNC cable kit Active ISD946 90m SMA TNC cable kit Active ISD947 100m SMA TNC cable kit Active ISD936 10m SMA TNC cable kit Passive ISD937 20m SMA TNC cable kit Passive IsatDock PRO Installation amp User Manual ISD939 30m SMA TNC cable kit Passive ISD940 40m SMA TNC cable kit Passive ISD941 50m SMA TNC cable kit Passive RST055 UPS Battery Pack Kit Contents IsatDock PR
11. ANSI IEEE C95 1 1992 Do not operate your satellite telephone when a person is within 55cm of the antenna A person or object within 55cm of the antenna could impair call quality and may cause the phone to operate at a higher power level than necessary and expose that person to RF energy in excess of that established by the FCC RF Exposure Guidelines As a precaution please maintain the maximum body distance possible from the antenna during call transmission IsatDock PRO Installation amp User Manual A WARNING ROAD SAFETY COMES FIRST Do not use a hand held cellular terminal satellite phone or mobile when driving a vehicle unless it is securely mounted in a holder for speaker phone operation Before making a call with a handheld terminal satellite phone or mobile park the vehicle stationary Please obey local road laws for hands free speakerphone operation Speakerphones hands free must be installed by qualified personnel Faulty installation or operation can constitute a safety hazard A IMPORTANT Cellular amp Satellite terminals or mobiles operate using radio signals and communication networks Because of this the connection cannot be guaranteed at all times or under all conditions Therefore you should never rely solely upon any wireless device for essential communications for example emergency calls IsatDock FCC Information This equipment has been tested and found to comply wit
12. BEAM IsatDock User Manual lt gt BEAM Product name IsatDock PRO Manual revision 02 Part Number USRMAN006102 Release date July 2011 BEAM Communications Pty Ltd 8 Anzed Court Mulgrave Victoria 3170 AUSTRALIA Information furnished by BEAM Communications Pty Ltd BEAM is believed to be accurate and reliable However no responsibility is assumed by BEAM for its use or for any infringement of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of BEAM BEAM reserves the right to change specifications at any time without notice Copyright 2010 BEAM Communications Pty Ltd All rights reserved IsatDock PRO Installation amp User Manual Beam Communications a wholly owned subsidiary of World Reach Limited WRR listed on the Australian Stock Exchange is a world leader in design manufacture and distribution of specialised communications equipment for the Inmarsat Satellite Network Beam s commitment to be at the forefront has continued to increase its share of the global satellite communications market Its premium distribution network spans the world Recognized as a leading provider of satellite communication solutions Beam specializes in Voice Data Tracking and customized solutions Beam develops innovative products and services to meet market demands and niche applicati
13. F status of the IlsatDock PRO accessory power If the accessory power in synchronization with a vessels operation is unavailable this may be connected By default the IsatDock PRO will stay on for 20 to a vehicle ignition voltage It is minutes after this input YELLOW wire is switched recommended to add a 1A fuse between off If a call is in progress while this occurs the them The accessory wire enables the IsatDock PRO will stay on for 20 minutes after the IsatDock PRO to turn on and off as the call is terminated Please follow the steps below to vehicle key is enabled or disabled If this connect the DC power cable to the vehicle battery function is not required the YELLOW wire power and the IsatDock PRO MUST be connected to the RED wire 5 Connect the 4 way Microfit connector on RED Vin 10 to 32VDC To Battery Positive Terminal the DC power cable to the 4 way power ra Requires 5A Fuse connector on the rear cable loom of the __ BLACK OV Power Ground IsatDock PRO To Negative Terminal or chassis YELLOW VON SLEEP To ON OFF switch 1A Fuse recommended IsatDock PRO Installation amp User Manual 21 8 Cable Routing The IsatDock provides three different cable routing options when installing the docking station Cables may exit via path A that travels around to the top of the dock allowing for the interface cables to be run with the external antenna connections Path B directs cables out
14. M Communications will not accept responsibility for any invoiced goods or services that are not covered by a BEAM Communications written purchase order Under no circumstances does BEAM Communications agree to pay for labour or other related expenses associated with the troubleshooting and or repair of our product without prior specific written authorization Information in our descriptive literature is based on product specifications that are current at the time of publication Product specifications designs and descriptive literature are subject to change as improvements are introduced Although we announce changes as they occur we cannot guarantee notification to every Customer BEAM Communications warrants delivered product to conform to the most current specifications designs and descriptive literature This warranty policy may be expanded or limited for particular categories of products or Customers by information sheets published as deemed appropriate by BEAM Communications The warranty for third party Products is that of the third party and not BEAM warranty IsatDock PRO Installation amp User Manual 35 BEAM Communications 8 Anzed Court Mulgrave Victoria 3170 AUSTRALIA Tel 61 3 8588 4500 Fax 61 3 9560 9055 Web www beamcommunications com Info info beamcommunications com Support support beamcommunications com lt N gt BEAM www beamcommunications com PART USRMAN006102
15. O 110 240V AC Plug Pack Privacy Handset 10 32V DC Power Cable Wall Mounting Plate Handset lock key User Manual amp Quick Start Guide NOTE Specifications are subject to change without notice It is ideal for the ambient temperature to be approximately 18 degrees below the 45 C upper limit for the handset to charge the battery whilst docked 31 1 Physical Dimensions PRO Dock 2 Physical Dimensions Privacy Handset 49 70mm o 206 97MM_ 243 6mm 3 Physical Dimensions Wall Bracket 716mm 51 0mm 60 0mm COE 23 16mm ae lt gt BEAM Trouble Shooting This chapter provides information to help you troubleshoot problems you may encounter while running the IsatDock How do know if my IsatPhone Pro is registered on the Inmarsat network The STATUS LED of the docking station will change to GREEN when the handset is registered and able to make calls on the network The IsatPhone Pro will also indicate Inmarsat in the top left corner of the screen display The handset and docking station turn s OFF every 20minutes Ensure the Ignition Accessories wire is connected to power If this is not connected or connected to ground the docking station will go into sleep mode after 20 minutes by default N
16. OK and listen for the dial tone The mute LED will flash yellow to indicate the RJ11 POTS is in use Dial using the full country codes on the RJ11 telephone keypad A message will display on the IsatPhone Pro handset to indicate the call is progressing Once the call is connected the STATUS LED will flash to indicate a call is in progress Place the RJ11 POTS phone handset ON HOOK to terminate the call Mobile Terminating 1 2 The RJ11 POTS phone will sound its ringer Lift the RJ11 POTS phone handset OFFHOOK to answer the call IsatDock PRO Installation amp User Manual Privacy Handset Use Mobile Originating 1 Remove the privacy handset from its cup 2 Dial the phone number using the full country code on the IsatPhone Pro keypad whilst docked Press the GREEN button to start the connection 3 A message is displayed on the IsatPhone Pro to indicate a call is in progress 4 Once the call is connected the STATUS LED will flash to indicate a call is in progress 5 Press the RED key on the IsatPhone Pro handset or return the privacy handset to its cup to terminate the call Options A During a call you may switch to speakerphone mode by pressing the speakerphone button on the IsatDock Return the privacy handset to its cup B To return the call back to the privacy handset remove the privacy handset from its cup Mobile Terminating 1 Answer the incoming call by un cupping the
17. a Up Down In a Call Increase decrease volume on the internal hardware or privacy Audio will sound louder quieter in privacy handset with each press OR handset Out of Call Increase decrease volume of incoming ring tone on the A beep will sound indicating the increased decreased ring tone volume internal hardware speaker P Mute In a Call BA 1 second Mute the microphone uplink on the privacy handset LED turns RED Muted LED turns OFF Not muted LED flashing Yellow RJ11 POTS in use Brightness Out of Call a a dual button Enter LED brightness change mode Press UP and DOWN a i i simultaneous arrows to vary intensity Mode will automatically exit after 5 All LED s will change to WHITE and a single beep will sound when entering press seconds after the last button press brightness change mode 1 second A short double beep will sound when exiting change mode Speakerphone Ina Call press ON OFF LED turns OFF Speakerphone mode not active 28 c S BEAM IsatDock PRO Buttons LED lights w WS REDIAL GREEN RED YELLOW N A N A N A N A MUTE GREEN RED YELLOW ON N A Outgoing audio is N A muted FLASHING N A N A POTS RJ11 in use LED STATUS GREEN RED YELLOW ON Handset registered and Handset not registered N A able to make a call no signal and cannot make or receive calls FLASHING Call in Progress N A N A ALTERNATING N A Error detected in N A communicating with IsatP
18. ding point that the Privacy handset rests upon For a wall mounted docking station this retains the privacy handset and the springless cup has enough height to allow the handset to rise up off the clip and out of the mounting cup 2 Spring Cup Heavy duty use cup In harsh environments the Privacy handset is actively retained in the mounting cup This is achieved by using the spring mounting cup To remove the handset from the cup the phone is lifted up against the pressure of the spring until it clears the lower mounting pip and can be removed from the docking station 4 Access to Rear Connector Bay For the IsatDock PRO the external cable interfaces are at the rear of the docking station The cover panel creates the IP rating for the electrical interface and retains the cables in their respective channels The cover panel is fixed in place by 7 screws IsatDock PRO Installation amp User Manual a USB Data Interface b Alert loop connection NOT IN USE c RJ11 POTS interface d DC power and accessory input e RJ9 Privacy handset 19 5 Connect RJ11 POTS Interface Any standard analogue POTS Telephone POTS Plain Old Telephone Service is supported by the IsatDock PRO It supplies power to the analogue phone as well as ring dial and busy tones Route the telephone cabling up to 600m fr
19. e calls 24 A NOTE 1 Ifthe IsatPhone Pro is removed from the dock during a call the call will drop out during this transition 2 One common cause for connection failure is a flat IsatPhone Pro battery which prevents the IsatPhone Pro from turning ON In these instances the docking station will attempt to charge the IsatPhone Pro handset while it is switched OFF until enough charge is present for the IsatPhone Pro to turn ON This charging period can take up to 20 minutes depending on how flat the battery Pro handset The IsatDock PRO provides charging power to the IsatPhone Pro handset via its USB connector The IsatPhone Pro battery is a lithium ion cell which has a safety temperature range whilst charging This range is from 0 to 45 degrees Celsius 32 to 113 degrees Fahrenheit Due to the increased heating effects on the IsatPhone Pro handset whilst it is docked and being charged it is ideal for the ambient temperature to be at least 18 degrees below the lt S BEAM 45 C upper limit for the handset to charge the battery whilst docked If the battery temperature exceeds this limit then the IsatPhone Pro may cease charging until the temperature is reduced Placing Voice Calls Bluetooth calls via IsatPhone Pro The IsatDock PRO allows for Bluetooth audio calls to be placed via the IsatPhone Pro handset while docked Consult the IsatPhone Pro manual for further information on pairing and Bluetooth di
20. h the limits for a Class B digital devices pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device has been designed to operate with antennas ISD710 ISD715 ISD720 and having a maximum gain of 6dBi dB Antennas having a gain grater than 6dBi dB are strictly prohibited for use with this device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful c
21. hone Pro handset Flashing Red Blue SPEAKER GREEN RED YELLOW ON Speakerphone Mode N A N A 1 Mute 2 Redial 3 Up amp Down q TA Sa 4 STATUS LED l Wi OT INN 5 Speaker Phone Button 2 IsatDock PRO Installation amp User Manual re oe a 5 29 Assuring Quality of Service There are conditions that can compromise the quality of the service you may receive These include Obstructions Cabling RF Interference Obstructions Nearby tall buildings or similar structures heavily leafed trees and mountains can all degrade performance as they block the signal between the antenna and the satellites Inmarsat performance is immune from natural environments such as clouds fog rain snow wind and smoke 30 Cabling Using an externally mounted antenna provides an ideal solution for many applications It is very important that both the antenna cabling and antenna are Beam approved products Always ensure all RF connectors are screwed together firmly and ensure there are no sharp bends in the cabling between the docking station and the antenna RF Interference All wireless devices including satellite telephones are susceptible to RF radio frequency interference from other electronic devices This problem is more evident when numerous antennas and broadcasting devices are located within close proximity to each other Symptoms of RF Interference Symptoms of RF interference often resemble t
22. hose that arise when an antenna is being operated with an obstructed view of the sky Some of these symptoms include erratic or no signal strength indication dropped calls or warbled or otherwise distorted voice These symptoms may be intermittent or persistent depending largely on the interference source its distance strength and frequency relative to the unit c lt S BEAM Mitigation of RF Interference Service degradation due to RF interference can be significantly improved by Increasing the distance and moving the BEAM antenna off axis from the source of the interference and Using an external band pass filter and an external antenna A WARNING Failure to use BEAM approved antenna cables will result in degraded performance and may damage the Docking Station This will void the product warranty Electrical amp Environmental Specifications lsatDock PRO GPS Antenna SMA Female 10 32 V DC 4 way microFit AC DC adator or DC lead Privacy Handset Port RJ9 connector Configuration Data USB Micro Speakerphone In built speaker microphone Certifications Inmarsat Type Approval FCC CE Compliance Electrical Safety ROHS Industry Canada C Tick EMC Compliance Accessories Average Power Average Watts Consumption Current 12v Power w o IsatPhone 130mA 1 6W Pro Standby Charging 360mA 43W Transmit Charging 875mA
23. ide the dock down Q Final lock position Once the dock as been locked onto the mount ing bracket on the wall two security bolts are then slid into place locking the dock to the wall IsatDock PRO Installation amp User Manual 17 3 Privacy Handset amp Mounting Cup The Privacy Handset is conveniently mounted on to the IsatDock PRO enclosure providing a local handset function The Privacy Handset connects to the docking station via a RJ9 connector The privacy handset is connected beneath the rear panel of the IsatDock Once connected the cable is run back through the foam and placed in the S channel through the base of the phone RJ9 connection See section 4 on page 19 Changing Cups 1 Unhook the privacy handset from cup 2 Remove cup cover to expose screws 3 Unscrew 3 screws with a phillips screwdriver 4 Detach the cup and replace with the spring or springless cup There are two options for the privacy handset mounting cup depending upon the environment or condition where the docking unit is mounted 1 springless cup for stationary use vertical or horizontal position 2 spring cup for rough conditions C S BEAM 1 Springless Cup for Normal light use Desk mounted cradle position The springless cup is fitted to the docking station with the mounting clip in a flush position Wall mounted cradle position The mounting clip can be slid out and reversed producing a protru
24. ly shielded electronic systems in motor vehicles Check with the manufacturer or its representative regarding your vehicle You should also consult the manufacturer of any equipment that has been added to your vehicle Performance of electronically controlled brake and or guidance systems can under certain unique conditions be subject to interference by mobile radio operation Although the transceiver meets all requirements regarding RF emissions you should mount the transceiver as far as possible from the guidance system and or braking modulator box usually located in the trunk to minimize any interference IsatDock PRO Installation amp User Manual Posted Facilities Turn your phone OFF in any facility where posted notices require such as hospitals and on board aircraft Aircraft Airline regulations prohibit using your phone while in the air Consult the local Aviation Authority for guidelines on use of the equipment on board an aircraft Vehicles Equipped with an Air Bag An air bag inflates with great force Do NOT place objects including both installed and portable wireless equipment in the area over the air bag or in the air bag deployment area If in vehicle wireless equipment is improperly installed and the air bag inflates serious injury could result ae IsatDock PRO is an intelligent docking station specifically designed for the Inmarsat IsatPhone Pro satellite handset IsatDock PRO allows the IsatPh
25. mes are those of their respective owners Radio Frequencies Sub Miniature version A co axial RF connection Connector type and reference for the POTS telephone port 4P4C connector for the privacy handset Plain Old Telephone Service Global Positioning System Inmarsat s Global Satellite Phone Service A Note Important Tip Header This symbol and associated text indicate a note providing general operating information bl SMA AN RJ11 RJ9 Interference Header POTS All wireless phones may get interference which GPS could affect performance GSPS PABX gt Record Header Write details of your unit for easy reference when required Ideal when troubleshooting Private Analogue Branch Exchange IsatDock PRO Installation amp User Manual Check that your IsatDock PRO package contains all of the following items L 1x IsatDock PRO Docking station L 1x 110 240V AC Plug Pack 1 x Privacy Handset 1 x 10 32V DC Power Cable O O QO 2 x Handset Locking Keys C 1x Wall Mounting plate L User Manual amp Quick Start Guide Falcon Configuration Tool is available for download from http www beamcommunications com support pro Optional Accessories The following optional accessories are available for your IsatDock PRO Active Antennas ISD715 Transport Magnetic Antenna Active ISD720 Transport Bolt Antenna Active Antenna Cable Kits for Active Antennas
26. n dust or metal powders x any other area where you normally would be advised to turn off your vehicle engine c lt S BEAM Safety Transceiver IsatPhone Pro Your handset is a low power radio transmitter and receiver When it is ON it receives and also sends out radio frequency RF signals NOTE Refer to Inmarsat IsatPhone Pro Manual for additional Information The Inmarsat IsatPhone Pro handset has an in built transceiver which is designed to be used with an external antenna This antenna transmits RF energy The BEAM antenna fitted via an extension coaxial cable to the cradle must be located more than 55cm from the human body person when in operation International agencies have set standards and recommendations for the protection of public exposure to RF electromagnetic energy These standards are based on extensive scientific review by scientists engineers and physicians from universities government health agencies and industry groups They review the available body of research to develop ANSI standard These ANSI standards are reviewed regularly for research development International Commission on Non lonizing Radiation Protection ICNIRP 1996 Verband Deutscher Elektrotechniker VDE DIN 0848 United States Federal Commission Radio Frequency Exposure Guidelines 1996 National Radiological Protection Board of the United Kingdom GS 11 1988 American National Standards Institute
27. ned to operate in negative ground 10 to 32 Volt DC electrical systems only If using the DC cable lead The best power connection point for the positive primary power lead is the positive terminal of the vehicle battery Often direct connection to the battery is inconvenient and you may find it easier to connect the positive leads to the starter solenoid Always select a point as close as possible to the battery Connect the negative primary power leads to a good ground point on the vehicle chassis or at the battery If you must attach the negative primary power lead directly to the negative pole of the battery you may optionally insert a 10 amp fuse not included into the ground lt gt BEAM OV line Failure to insert a fuse can cause equipment to overheat if a wiring fault exists Many parts of a vehicle can produce electrical noise that interferes with the electrical radio system operation The ignition system is the most common source of electrical noise interference Before you begin installation ensure that the ignition wiring and connections to the vehicle battery are in good working condition e Verify that low resistance connections are present between the battery negative terminal the vehicle chassis and the engine block All wire connections should be clean and tight e For vehicle installation install provided fuses into the BATT and ignition sense accessory wires A WARNING Do not connect
28. o power on IsatDock Check power is connected to the interface unit Ensure the Connector cable to the IsatDock is firmly fitted Check all the connection cables to and from the IsatDock The signal bars are low or fluctuating and call quality is poor Party B cannot hear your voice Ensure all antenna connectors are tight The antenna is operating in a location that it can see the satellite and there are no obstructions Beam certified antenna cabling is being used and there are no sharp bends or cuts in the cable If using a fixed passive antenna ensure it is orientated correctly and pointing at the satellite Privacy Handset must be docked in its cup when not in use Check that MUTE is not ON indicated by turning RED Check the signal strength on the handset Ensure the Headset connector at the base of the IsatPhone is not obstructed and there is no dust or foreign objects in the connector socket I am looking for the latest manuals and support information on the docking station The docking station appears to be turning ON OFF and the handset is not registering Visit http www beamcommunications com support inmarsat Dropped calls Ensure the power supply can provide at least 3 5A at 12volts If power is being supplied from a battery ensure the connections are tight and the contacts are clean ig i Due to a satellite network when y
29. om the analogue phone Mount the analogue phone if required and plug the RJ11 cable into the IsatDock PRO RJ11 port RJ11 port See section 4 on page 19 xi j 20 6 USB Port Connection IsatDock PRO has a micro USB Data Port for programming interface to enable upgrading of the Docking station firmware USB Data Port See section 4 on page 19 C DOBEAM 7 Connecting Power to the Dock DC Power Source Installation The Dock can be powered from the supplied AC 1 Route the wire end of the DC power cable Plug pack or connect to an external 10 32V DC to the connection point power supply YELLOW 2 Connect the BLACK wire to the negative RED terminal of the battery 10A fuse ISD950 AC Plug Pack Installation BEACK recommended or the vehicle chassis if For installation using ISD950 110 240 AC plug negatively grounded chassis pack connect the 4 way Microfit connector from The DC power cable has three wires RED 3 Connect the RED wire to the positive the plug pack to the 4 way power connector on BLACK and YELLOW The RED and BLACK wires terminal of the battery It is recommended the rear of the IsatDock PRO In this configuration are used for the power connection while the to add the 5A fuse supplied between the ignition accessory status is always ON YELLOW wire can be connected to a vessels them accessories ignition or other similar circuits to 4 Connect the YELLOW wire to the vehicle control the ON OF
30. ommunication A WARNING Changes or modifications not expressly approved by BEAM Communications could void the product warranty c lt S BEAM Electronic Devices Most modern electronic equipment is shielded from RF signals However certain equipment may not be shielded against the RF signals from your wireless phone Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six inches 6 be maintained between a wireless phone s antenna and a pacemaker to avoid potential interference with the pacemaker These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research Persons with pacemakers Should ALWAYS keep the phone more than six inches from their pacemaker when phone is turned ON Should turn the phone OFF immediately if you have any reason to suspect interference is taking place Other Medical Devices If you use any other personal medical device consult the manufacturer of your device to determine if it is adequately shielded from external RF energy Your physician may be able to assist you in obtaining this information Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy Vehicles RF signals may affect improperly installed or inadequate
31. one Pro handset to be used in a wide variety of applications It enables you to use an intelligent RJ11 POTS connection with a standard corded cordless or DECT handset Alternatively it can also be interfaced with a PBX system IsatDock PRO has an in built speakerphone for convienent handsfree operation IsatDock Design All in one design High quality ABS Plastic Single action insertion mechanism Key lockable amp securable to wall desk Wall or desk mounting options Accessible control buttons Slimline privacy handset Integrated antenna connections In built speaker microphone Cable routing LHS TOP BOTTOM In Built Speakerphone e In built speaker and microphone Power 10 32V DC Input e 110 240V AC plug pack included Buttons on Dock Ringer volume up down In call volume up down Last number redial In call mute Speaker hands free button Intelligent POTS RJ11 Interface Supports 10 32V DC power input Flexible installation via wall or desk mounting option Supplied with 110 240V AC DC Plug pack Other Key Features Active privacy handset Status LED with adjustable brightness USB data c DOBEAM Equipment Overview 1 IsatDock PRO unit 7 Mounting Cup spring or springless cup options 2 Privacy Handset Speaker under handset 3 Speakerphone Microphone Speakerphone Button Key lock ON Oo hw IsatPhone Eject Button 9 IsatPhone Pro not included 10 Func
32. ons Beams leading edge products are deployed in a wide range of vertical markets including Maritime Transport Government Defence Mining Construction Forestry Emergency Services Relief Aid Telemetry and Rural Telephony Supported by a dedicated team of professionals Beam has developed solid relationships with its peers and network of distributors worldwide lt gt BEAM S gt BEAM BEAM Communications Pty Ltd 8 Anzed Court Mulgrave Victoria 3170 AUSTRALIA Web www beamcommunications com Information info beamcommunications com Support support beamcommunications com Tel 61 3 8588 4500 Fax 61 3 9560 9055 These notes will appear throughout this manual and should be taken into consideration Terminology DESCRIPTION Falcon Configuration Tool MS Windows Install A Falcon Warning or Caution SMS Short Message Service Thi boland jated text indicat is symbol and associated text indicate a Mobile Originating Describes a call initiated by the IsatDock warning note providing information to prevent r sd Mobile Terminating damage to equipment or personal injury Describes an incoming call being answered by the IsatDock IsatPhone Pro The Inmarsat IsatPhone Pro handset The symbol mark and logos are owned by the respective companies of which the symbol follows Any use of such marks by Beam Communications is under license Other trademarks and trade na
33. ou are in motion the satellite signal may become obstructed such as buildings bridges tunnels larger vehicles Check the antenna connection Ensure the antenna cable has not been damaged Ensure that only approved antenna cable has been used Refer to Antenna Install Guide on Beam website support IsatDock PRO Installation amp User Manual 33 Beam Warranty Conditions BEAM Communications gives this express warranty along with extended warranty endorsements where applicable in lieu of all other warranties express or implied including without limitation warranties of merchantability and fitness for a particular purpose This constitutes our sole warranty and obligation with regard to our products as well as the Customer s sole remedy BEAM Communications expressly disclaims all liability and responsibility for any special indirect or consequential damages or any further loss of any kind whatsoever resulting from the use of our product s The Customer s sole and exclusive remedy and the limit of BEAM liability for any loss whatsoever shall not exceed the purchase price paid by the Customer for the product to which a claim is made All products manufactured by BEAM Communications are warranted to be free from defects in material and workmanship in accordance with and subject to the following terms and conditions 1 This warranty is limited to the original Customer only It cannot be transferred or a
34. privacy handset from its cup 2 Press the RED key on the IsatPhone Pro handset or return the privacy handset to its cup to terminate the call 25 Mute Mode Mute functionality The mute function of the IsatDock PRO allows the user to mute the uplink microphone audio on the privacy handset and or internal speakerphone microphone 1 During a call Press the Mute button on the face of the IsatDock PRO a RED LED will illuminate the Mute button to confirm that the IsatDock PRO is muted 2 To exit the mute mode press the mute button once USB Driver Installation The IsatDock PRO USB data port requires an interface driver to be installed on the user s computer prior to undertaking data communication This driver supports the following operating systems Windows XP SP3 or above amp Windows Vista You can download the Windows Driver for the IsatDock from http www beamcommunications com support pro 26 Configuration using Falcon Falcon can be downloaded from http www beamcommunications com support pro Follow the instructions in the downloaded application to install Once complete connect your PC to the USB port of the terminal and start Falcon You can then use the application for a range of options such as View the status of the terminal signal temperature input voltage Firmware maintenance Configure different POTS RJ11 settings A NOTE Entering the firmware upgrade mode will be
35. scovery setup Speakerphone Phone Call Use Mobile Originating 1 By default the IlsatDock PRO will start all calls in speakerphone mode when dialing on the keypad without RJ11 or privacy handset off hook 2 Dial using the full Inmarsat dialing sequence eg 00 country code and telephone number on the IsatPhone Pro keypad whilst docked Press the GREEN button to start the connection 3 A message will display on the IsatPhone Pro handset to indicate the call is progressing 4 Once the call is connected the STATUS LED will flash to indicate a call is in progress 5 Press the RED key on the IsatPhone Pro handset or press the speakerphone button to terminate the call Options A During a call you may use the optional privacy handset by taking the privacy handset out of its cup This automatically directs the call audio to the privacy handset To return the call back to speakerphone mode press the speakerphone button and return the privacy handset to its cup Mobile Terminating 1 Answer the incoming call by pressing the Speakerphone button or the GREEN key on the IsatPhone Pro handset Once the call is in progress the same options are available as described in Speakerphone Phone Call Mobile Originating Press the RED key on the IsatPhone Pro handset or press the speakerphone button to terminate the call RJ11 POTS Phone Use Mobile Originating 1 Lift the RJ11 POTS phone handset OFFHO
36. ssigned to third parties unless the intent to transfer to a third party is expressly indicated in a purchase order and or warranty processing arrangements have been agreed upon in writing by BEAM 34 BEAM Communications does not warrant any installation maintenance or service of the Products not performed by BEAM nor does it warrant the use of Products with unapproved ancillary products BEAM Communications will correct any defects in material or workmanship of products manufactured by BEAM which appear within 12 months and 24 months replacement warranty for Docking Station units ONLY from the date of shipment by BEAM Communications to the Customer BEAM Communications will repair or replace at our option any defective product provided that our analysis and or inspection discloses that such defects developed under normal and proper use This warranty does not extend to goods subjected to liquid or particulate ingress extreme humidity misuse neglect accident or improper installation or to maintenance or repair of products that have been altered or repaired by anyone except BEAM Communications unless otherwise stated in writing The warranty is a return to base warranty and freight is paid by the sender A charge of USD 150 including return freight will be made for testing returned product which is not defective or is found to be defective as the result of improper use maintenance or neglect lt gt BEAM BEA
37. tion Buttons 11 STATUS Indication Light 12 Back Panel Connectors 4 a USB Data Interface c RJ11 POTS interface d DC power and accessory input e RJ9 Privacy handset IsatDock PRO Installation amp User Manual istallation Guidelines This guide outlines the process for installing the IsatDock PRO in conjunction with an Inmarsat IsatPhone Pro handset This kit must not be used with any other device other than the Inmarsat IsatPhone Pro handset Only trained personnel should install communication equipment Ensure that the unit is protected from dirt and moisture Select an area to mount components where there is no interference with other objects Astrong mounting surface should be chosen to ensure the terminal doesn t loosen over time Mount all components securely for safe day to day operation Always use the supplied mounting hardware Leave space around the unit to allow airflow and ensure there is adequate clearance for cables Ensure the units can be easily accessible for servicing Routing Cables Route cables so they are protected from pinching sharp edges and crushing Use grommets wherever a cable must pass through a hole in a metal panel Keep all in line connectors accessible Foran extra clean installation a hole may be driven through the surface directly behind the docking station Guidelines for Electrical Connections The system is desig
Download Pdf Manuals
Related Search