USER MANUAL - GMI
Contents
1. Screw terminals terminals are available for 18 28 AWG Made in the U S A 2 2 DESCRIPTION The Patton 52X TS Series of terminal strip surge protectors lets you design a custom surge protector to fit just about any 2 4 6 8 or 10 wire application To design your custom surge protector specify the number of lines you need protected Then specify the clamping voltage for example 18V for RS 232 or 7 5V for RS 422 RS 485 Token Ring or Ethernet that is optimal for your application Each surge protector comes with input output terminal strips and strain relief straps Simply attach your stripped wires to the surge protector and terminate the ends with whatever connectors you choose See Section 3 0 for installation details The Patton 52X TS Series provides reliable transparent protection at data rates up to 20 Mbps so you can be confident using these protectors in a wide variety of Local Area Networks LANs Wide Area Networks WANs and data communications environments Surge energy is intercepted by a solid state hybrid circuit and diverted safely to chassis ground through a braided metal strap The 52X TS Series can handle repeated surge hits up to 1 5 k Watts without degrading its performance Each Patton 52X TS Series protector is equipped with a heavy duty braided metal strap to shunt harmful over voltages safely to ground It is housed in a sturdy flame retardant plastic case UL94 5V flame rating Warning Should your2. equipment or building be subject to a direct lightening strike this product will not provide complete protection 3 0 INSTALLATION This section tell you how to open the case how to connect the bare wires to the terminal blocks and how to fasten the strain relief strap to secure the wires Make sure you follow the installation instructions exactly If the suppressor is improperly installed the current limiting feature could be rendered inoperable If you have any question as to how your hardware is grounded consult the manufacturer s user manual s 1 Open the case by inserting a screwdriver into the side of the case opening and gently turn the screwdriver The case will pop open Once the case is open you will see the terminal blocks Figure 1 Opening the 52X ST Case 2 As show in Figure 2 strip the outer insulation from the wires about 1 inch from the end 9 en Figure 2 Stripping the 52X ST Outer Insulation Strip off the insulation on each of the wires about 0 25 inches 6 centimeters Place the cable through the end plate and under the cable tie installed on the board Make a small loop in the cable using the cable ties provided to hold the loop in place Tighten both cable ties Figure 3 below shows the correct connection lt O gt Figure 3 Installing the 52X TS Cable Connect the wires to t
3. USER MANUAL TS Series Model 52X Terminal Strip Surge Protectors Part 07M52X A Doc 074170U Revised 10 21 96 u me a PATTON Electronics To SALES OFFICE 301 975 1000 TECHNICAL SUPPORT 301 975 1007 http www patton com 1 0 WARRANTY INFORMATION Patton Electronics warrants all 52X TS Series components to be free from defects and will at our option repair or replace the product should it fail within one year from the first date of shipment This warranty is limited to defects in workmanship or materials and does not cover customer damage abuse or unauthorized modification If this product fails or does not perform as warranted your sole recourse shall be repair or replacement as described above Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product These damages include but are not limited to the following lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Patton Electronics specifically disclaims all other warranties expressed or implied and the installation or use of this product shall be deemed an acceptance of these terms by the user 1 1 SERVICE All warranty and nonwarranty repairs must be returned freight prepaid and insured to Patton Electronics All returns must have a Return Materials Authorization number on the outside of the shipping container This number may b
4. e obtained from Patton Electronics Technical Support 301 975 1007 http www patton com or support patton com Notice Packages received without an RMA number will not be accepted Patton Electronics technical staff is also available to answer any questions that might arise concerning the installation or use of your Model 52X Technical Service hours 8AM to 5PM EST Monday through Friday 1 2 CE NOTICE The CE symbol on your Patton Electronics equipment indicates that it is in compliance with the Electromagnetic Compatibility EMC directive and the Low Voltage Directive LVD of the Union European EU A Certificate of Compliance is available by contacting Technical Support 2 0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product This product has been thoroughly inspected and tested and is warranted for One Year parts and labor If any questions during installation or use of the 52X TS contact Patton Electronics Technical Support 301 975 1007 http www patton com or support patton com 2 1 FEATURES Choose from 2 4 6 8 or 10 wire Terminal Strip configurations Clamping voltages for RS 232 RS 422 RS 485 Token Ring or Ethernet Call for custom options Supports asynchronous or synchronous data rates up to 20 Mbps Strain relief straps hold wires firmly in place Surge handling capacity of 1500 Watts Surge energy is diverted to ground through braided metal strap
5. he terminal blocks Use Figure 4 to ensure that each wire of the 52X TS is connected to the correct corresponding pin number on the opposite side of the protector Also shown in Figure 4 is the proper wire pairing for the 52X TS 0000000000 1 OOOO0O0DOOO Ep o Ep o Figure 4 52X TS Differential Pairing and Pin Numbers APPENDIX A MODEL 52X ST SPECIFICATIONS Interface Connectors Wires Protected Surge Capacity Clamp Voltage Maximum Speed Construction Size Relative Humidity Temperature RS 232 RS 422 485 Ethernet Token Ring Terminal Strip 2 4 6 8 or 10 400A 8 20 uS Residual surget 2 kV 1 2 50uS 1 kA 8 20US wave form 105 volts 20 Mbps UL94 5V rated flame retardant plastic 3 0 7 62cm x 1 67 4 24cm x 8 2 03cm 5 to 95 noncondensing 40 to 85 C 40 to 185 F t Residual surge is a special term defined by the IEEE and NEMA to replace the term clamp voltage
Download Pdf Manuals
Related Search