Base Pan Heater Installation Manual
Contents
1. o i Cabinet Top Plate Right Mounting Miale Cabinet screws Front gt Front Plate Plate gv Mounting i screws l Step 2 Installation Work Guide Base Pan Heater for heating cable side 1 Identify the heating cable side from end splice to the black marking refer to the base pan heater specification 2 Begin guiding the heating cable from end splice Fix the heating cable with 1st 2nd 3rd 4th and 5th band 2 refer to Figure 2a 3 Use cable tie 3 to tie the heater with the bottom tube of condenser refer Figure 2b and fix the heater with 6th 7th and 8th band Make sure the heater is as near as possible to the condenser side 4 Continue guide the heater follow the routing insert the heater below the condenser where possible and make sure the heater is between the condenser and water discharge hole 5 When the heater reaches the end turn back to the opposite direction toward the fan motor bracket and tie the cable with the cable tie B provided after the black marking on the cable Refer Figure 2c Note All heating cable should touch to the base pan Itis not encourage to remove the Propeller Fan during installation of the base pan heater Figure 2 Fan Motor Base Pan Heater 1 must pass by these holes Bracket A iy Guide through the band o WU N hole near to the Condenser E m Turn at sfa gt gt this point Condenser AF Fan Motor Bracket a S 7 5 End splice nll Start guide fro2. blade to cut the cable 3 Guide the cold cable through the second band on the control board 4 Guide the cold cable through the twisted band Refer to Figure 3b 5 On the refrigerant system PCB locate CN HT2 BLACK Unplug the dummy connector then replace with base pan heater cable s connector Refer to Figure 3c 3d and 3e Figure 3 Refrigerant System PCB Refrigerant System PCB Refrigerant System PCB Condenser gt gt gt Remove this dummy connector Please tie up the base Cab oan the al Plugin tha y Please tie up cold cable rou 6 base pan pan heater with these 2 With this adjustable band second band heater cable s adjustable band j Connoator Step 4 Switch on the Base Pan Heater Control System Please tie 3b Remove n up the base Please tie up the thle dumeny A pan heater base pan heater Bian ty 3a with these 3 with these 2 Plug inthe adjustable adjustable band bace pan Fan Motor Sound Proof band eater cable s Bracket Board connector Step 4 Switch on the Base Pan Heater Control System 1 On the top right portion of water system PCB search for SW2 switch Refer to Figure 4a and 4b 2 Push the toogle on terminal 3 from Off to On positon Refer to Figure 4c This is to activate the base pan heater function Water System PCB Figure 4 1 On the to
3. Panasonic H F614873 ase ater Installation Manual Required tools for Installation Works 1 Philips screw driver 2 Glove 3 Cutter 4 Plier 5 Multimeter SAFETY PRECAUTIONS e Read the following SAFETY PRECAUTIONS carefully before installation e Electrical work must be installed by a licensed electrician e The caution items stated here must be followed because these important contents are related to safety The meaning of each indication used is as below Incorrect installation due to ignoring of the instruction will cause harm or damage and the seriousness is classified by the following indications A WARNING This indication shows the possibility of causing death or serious injury A CAUTION This indication shows the possibility of causing injury or damage to properties only The items to be followed are classified by the symbols SQ Symbol with white background denotes item that is PROHIBITED from doing Symbol with dark background denotes item that must be carried out e Carry out test run to confirm that no abnormality occurs after the installation Then explain to user the operation care and maintenance as stated in instructions Please remind the customer to keep the operating instructions for future reference Z WARNING 1 Be sure to disconnect all power supply before install and connect the Base Pan Heater Otherwise it will cause the electrical
4. d remove 8 screws on the cabinet front plate then unhook it and pull to remove the plate Refer to Figure 1c Figure 1b Figure 1c Cabinet Top Plate Cabinet Front Plate Figure 1a Screws Screws Step 2 Installation Work Guide Base Pan Heater for heating cable side 1 Identify the heating cable side from end splice to the black marking refer to the base pan heater specification 2 Begin guiding the heating cable from end splice Fix the heating cable with 1st 2nd 3rd 4th and 5th band 2 refer to Figure 2a 3 Use cable tie E to tie the heater with the bottom tube of condenser refer Figure 2b and fix the heater with 6th 7th and 8th band Make sure the heater is as near as possible to the condenser side 4 Continue guide the heater follow the routing insert the heater below the condenser where possible and make sure the heater is between the condenser and water discharge hole 5 When the heater reaches the end turn back to the opposite direction toward the fan motor bracket and tie the cable with the cable tie 3 provided after the black marking on the cable Refer Figure 2c Note All heating cable should touch to the base pan Itis not encourage to remove the Propeller Fan during installation of the base pan heater Figure 2 Base Pan Heater 1 must pass by these holes we Fan Motor P Bracket irr Ny Guide through the band MW N hole near to the Condens
5. er Turn at this point Condenser 7 Do not modify the length of the Base Pan Heater lead wires Otherwise it will cause abnormal operations fire or electrical shocks 8 Use glove and proper tools when doing installation job to prevent cutting by metal part or any sharp edges part 9 Do not touch to the heating cable when the Base Pan Heater is on It will cause injured due to high temperature at heating cable s surface SISS S S S 6 616 A Fan Motor Bracket End splice iy Start guide from here 2x8 Pass by pan this hole Insert to this 2 diameter 5mm holes How to fixed Base Pan Heater 1 with band 2 Attached Accessory No Accessory Part Qty No Accessory Part Qty Base Pan Heater Cable Tie 1 O 1 Ol e WZ Band 2 8 Base Pan Heater Specification Heating cable length 1700 mm Cold cable length 1600 mm T gt B End Splice CSC2E 1 7m 85W 230V DO NOT CUT THE CABLE A341075 CE Batch n Black Marking Protection class IP 67 Power 85W 10 Minimum bending radius 20mm f Connector Black marking 2a Total 8 position Make sure this black marking is before the cab
6. heater follow the routing insert the heater below the condenser where possible and make sure the heater is between the condenser and water discharge hole 5 When the heater reaches the end turn back to the opposite direction toward the fan motor bracket and tie the cable with the cable tie 3 provided after the black marking on the cable Refer Figure 2c Note All heating cable should touch to the base pan Itis not encourage to remove the Propeller Fan during installation of the base pan heater Figure 2 Base Pan Heater 1 must pass by these holes pees Turn at a this point Fan Motor Guide through the band hole near to the Condenser Condenser Fan Motor Bracket End splice WU Start guide from here Pass by this hole Insert to this 2 diameter 5mm holes How to fixed Base Pan Heater 1 with band 2 Black marking 2a Total 8 position J Make sure this black marking is before the cable tie and touch to base pan Step 3 Installation Work Guide Base Pan Heater cold cable side 1 Locate the 2 adjustable cable tie refer to Figure 3a Untie them by follow the step below 2 Tie the cold cable at these 2 position with the existing cable refer Figure 3a Make sure no dangling cables after tying the cables Any dangling cable will cause fan s
7. inal 3 from Off to On positon Refer to Figure 4c This is to activate the base pan heater function Figure 4 Before a o Eein How to Install Base Pan Heater to Mono bloc Unit Double Fan WH M F M C Models Before installing the Base Pan Heater steps below need to be carried out to remove the exterior chassis Z WARNING Be sure to switch off all power supply i e indoor power supply heater power supply Tank Unit power supply before performing the steps below to avoid electrical shocks etc Step 1 Removal of the Cabinet Plate 1 Locate and remove the 5 mounting screws slide down the cabinet and pull toward front to remove the right Cabinet Front Plate Refer Figure 1a 2 Locate and remove the 11 mounting screws Lift up the Cabinet Top Plate to remove it from fixing Refer Figure 1b 3 Locate and remove the 5 mounting screws slide downward and pull toward front to remove the middle Cabinet Front Plate Refer Figure 1c 4 Locate and remove 8 screws on the left Cabinet Front Plate then unhook it and pull to remove the plate Refer to Figure 1d Figure 1a Figure 1b Mounting A screws Figure 1c Figure 1d rf Left Cabinet Front Plate
8. le tie and touch to base pan l Step 3 Installation Work Guide Base Pan Heater cold cable side J 1 Locate the 3 adjustable cable tie refer to Figure 3a Untie them by follow the step below OPul 4 Push 7 2 Tie the cold cable at these 3 position with the existing cable refer Figure 3a Make sure no dangling cables after tying the cables Any dangling cable will cause fan s blade to cut the cable 3 Insert the cold cable through a hole on the sound proof board Follow fan motor s cable routing 4 Upon insertion tie the cable to the another 2 adjustable cable ties Refer to Figure 3b 5 On the outdoor unit PCB locate CN HT2 BLACK Unplug the dummy connector then replace with base pan heater cable s connector Refer to Figure 3c 3d and 3e 7 1 I Figure 3 In J insert through Refrigerant Outdoor PCB Outdoor PCB LA this hole Piping a gt gt Please tie Pema upthebase Please tie up the This dummy pan heater base pan heater with 3d 3a with these3 these 2 adjustable Plug in the base adjustable band pan heater cable s Fan Motor Sound Proof band connector Bracket Board Step 4 Switch on the Base Pan Heater Control System in Indoor Unit 1 Remove the exterior chasis of indoor unit to access control board area 2 On the top right portion of PCB search for SW2 switch Refer to Figure 4a and 4b 3 Push the toogle on term
9. m here Pass by 4 this hole Insert to this 2 diameter 5mm holes How to fixed Base Pan Heater 1 with band El Black 2a marking Total 8 position Make sure this black marking is before the cable tie and touch to base pan l Step 3 Installation Work Guide Base Pan Heater cold cable side 1 Locate the 3 adjustable cable tie refer to Figure 3a Untie them by follow the step below D Pull 4 Push 7 2 Tie the cold cable at these 3 position with the existing cable refer Figure 3a Make sure no dangling cables after tying the cables Any dangling cable will cause fan s blade to cut the cable Insert the cold cable through a hole on the sound proof board Follow fan motor s cable routing Upon insertion tie the cable to the another 2 adjustable cable ties Refer to Figure 3b On the refrigerant system PCB locate CN HT2 BLACK Unplug the dummy connector then replace with base pan heater cable s connector Refer to Figure 3c 3d and 3e ano Figure 3 Refrigerant Piping Insert through Refrigerant System PCB Refrigerant System PCB this hole gt gt How to Install Base Pan Heater to Mono bloc Unit Single Fan WH M F M C Models Before installing the Base Pan Heater steps below need to be carried out to remove the exterior chassis Z WARNING Be sure to switch off all power supply i e indoor power supply heater power s
10. p right portion of water system PCB search for SW2 switch Refer to Figure 4a and 4b 2 Push the toogle on terminal 3 from Off to On positon Refer to Figure 4c This is to activate the base pan heater function Figure 4 Before 1 Water System PCB 4b F614873 Q PRINTED IN MALAYSIA
11. shock 2 Engage authorized dealer or specialist for installation If installation done is defective it will cause electrical shock or fire 3 Install according to this installation instructions strictly If installation done is defective it will cause electrical shock or fire 4 Use the attached accessories parts and specified parts for installation Otherwise it will cause fire or electrical shock cause the electrical shock or fire 5 For electrical work follow the local national wiring standard regulation and this installation instruction Otherwise it will 6 Heater routing must be properly arrange so that the set can be fixed properly Or else it will damage by the propeller etc that may damage the set r fan How to Install Base Pan Heater to Bi bloc Unit Double Fan WH U Models Before installing the Base Pan Heater steps below need to be carried out to remove the exterior chassis Z WARNING Be sure to switch off all power supply i e indoor power supply heater power supply Tank Unit power supply before performing the steps below to avoid electrical shocks etc Step 1 Removal of the Outdoor Unit Exterior Chassis 1 Locate and remove 9 mounting screws on the cabinet top plate then remove the plate Refer to Figure 1a 2 Locate and remove the screws on the bottom of cabinet front plate then slide down and pull to remove the plate Refer to Figure 1b 3 Locate an
12. upply Tank Unit power supply before performing the steps below to avoid electrical shocks etc Step 1 Removal of the Cabinet Plate 1 Locate and remove the 5 mounting screws slide down the cabinet and pull toward front to remove the right Cabinet Front Plate Refer Figure 1a 2 Locate and remove the 11 mounting screws Lift up the Cabinet Top Plate to remove it from fixing Refer Figure 1b 3 Locate and remove the 4 mounting screws slide downward and pull toward front to remove the middle Cabinet Front Plate Refer Figure 1c 4 Locate and remove 5 screws on the left Cabinet Front Plate then unhook it and pull to remove the plate Refer to Figure 1d Figure 1a Figure 1b Figure 1c Left Cabinet Front Plate Middle Cabinet Front Plate Figure 1d Mounting screws Hook t Cabinet Top Plate screws Hook Mounting screws Mounting screws Step 2 Installation Work Guide Base Pan Heater for heating cable side Identify the heating cable side from end splice to the black marking refer to the base pan heater specification 2 Begin guiding the heating cable from end splice Fix the heating cable with 1st 2nd 3rd 4th and 5th band 2 refer to Figure 2a 3 Use cable tie B to tie the heater with the bottom tube of condenser refer Figure 2b and fix the heater with 6th 7th and 8th band Make sure the heater is as near as possible to the condenser side 4 Continue guide the
Download Pdf Manuals
Related Search