Tesira® TEC-1s & TEC-1i Operation/Installation Manual
Contents
1. 0 4 4 4 5 85 6 7 80 85 8 9 10 e 0 40C 32 104 F e 0 95 e 0 10 000 e e PoE IEEE 802 3af Class 1 e e HL TJ Fe 182. 101612 585 0316 90B 15 FCC COMPLIANCE FCC NOTICE CLASS B DIGITAL DEVICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in either a residential or commercial installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to cor rect the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected or 4 Consult the dealer or an experienced radio TV technician for help 16 EC DECLARATION OF CONFORMITV CE EC Declaration of Conformitv Biamp Systems Corporation as manufacturer having sole responsibility hereby declares that our delivered version the following described product complies with the applicable provisions of
3. 13 TEC 1 SPECIFICATIONS TEC 1s SPECIFICATIONS Dimensions Weight Power consumption Control cable requirements Control cable length Devices per system Remote Ethernet Devices including NPS 1 per system Remote Ethernet Devices per Tesira unit Control wiring topology Control programming Compliance 5 H x 4 7 W x 1 25 D 150mm x 120mm x 32mm O 5 Ib O 2kg PoE Class 1 3 2W full display utilization PVC ABS Unshielded twisted pair UTP wiring IOOBaseT interface CAT 5 6 7 Ethernet cable using either RJ45 or Insulation Displacement Connector IDC 330 100m Ethernet cable length can be extended with standard PoE network technology Standard Ethernet network wiring Each control configured for specific operation by the system design software EU Directive 2002 95 EC RoHS Directive CE marked FCC TEC 1i SPECIFICATIONS Dimensions Power consumption Control cable requirements Control cable length Control wiring topology Control programming Compliance 6 22 H x 5 82 W x 0 5 D 158mm x 148mm x 12 7mm PoE Class 1 3 2W full display utilization Unshielded twisted pair UTP wiring IOOBaseT interface CAT 5 6 7 Ethernet cable using either RJ45 or Insulation Displacement Connector IDC 330 100m Ethernet cable length can be extended with standard PoE network technology Standard Ethernet network wiring Each control configured for specific opera
4. 4 Electro mechanical fans electrolytic capacitors gooseneck microphones cords connecting handheld microphones hard drives displays and normal wear and tear of items such as paint knobs handles keypads and covers are not covered under this warranty All server based devices are warranted for 3 years only 5 This warranty is in lieu of all other warranties expressed or implied Biamp Systems disclaims all other warranties expressed or implied including but not limited to implied warranties of merchantability and fitness for a particular purpose 6 The remedies set forth herein shall be the purchaser s sole and exclusive remedies with respect to any defective product 7 No agent employee distributor or dealer of Biamp Systems is authorized to modify this warranty or to make additional warranties on behalf of Biamp Systems Statements representations or warranties made by any dealer do not constitute warranties by Biamp Systems Biamp Systems shall not be responsible or liable for any statement representation or warranty made by any dealer or other person 8 No action for breach of this warranty may be commenced more than one year after the expiration of this warranty 9 Biamp Systems shall not be liable for special indirect incidental or consequential damages including lost profits or loss of use arising out of the purchase sale or use of the products even if Biamp Systems was advised of the possibility of such damages
5. PoE network technology routers switches hubs media converters Connects with standard RJ45 or insulation displacement connector IDC Covered by Biamp Systems five year warranty CD Player b Radic b Microphone Video Conference CO Player Microphone Video Conference TEC 1i TEC 1s TEC 1 FRONT PANEL Hizr Video Conference a mm 3 eo 4 Select 4 Scroll Latch Setup and Use The Tesira software provides an intuitive interface for setup and programming of the TEC 1 The information supplied by this manual relates to physical connections and device setup For more details on software setup please consult the Tesira Help File Display A graphic OLED Organic Light Emitting Diode display with white characters on a black background shows a list of all control items available from that panel as well as the last selected item If a control item includes a volume control assignment the bottom of the display will show a graphical representation of a volume bar with the current level indicated to the right percentage of maximum level Capacitive touch Scroll Wheel The capacitive touch sensor provides a sleek interface for menu navigation and selection The glossy finish finger groove allows for scrolling through and selecting available control items as well as adjusting volume TEC 1 BACK PANEL Lr EM Connectors Two Ethernet connect
6. the DIRECTIVES below except as noted herein Any alterations to the product not agreed upon and directed by Biamp Systems Corporation will invalidate this declaration Brand Name Tesira Product Description Remote Audio Controls for Networked Audio DSP Platform Models TEC 1i TEC 1s Applicable EC Directives Applicable Harmonized Standards LVD Directive 2006 95 EC Safety EN 60065 2002 IEC 60065 2001 4 Amd 1 2005 EMC Directive 2004 108 EC Emissions EN 55103 1 1996 Environment E2 Immunitv EN 55103 2 1996 Environment E2 RoHS Directive 2011 65 EU RoHS Recast Special Considerations for Product Environment or Compliance e Use only PoE Insertion Devices that are CE Marked certified to local regulations and appropriately rated Type 1 PoE or Type 2 PoE Plus IEEE 802 3at e Shielded cabling must be used for system connections Technical Construction File Location and Contact Biamp Systems Corporation phone 503 641 7287 9300 S W Gemini Drive fax 503 626 0281 Beaverton OR USA 97008 e mail compliance biamp com Authorized Representative Larry Copley Compliance Engineer Authorized Signature Date and Place Issued May 2012 Beaverton Oregon USA 17 COMPLIANCE EU RoHS COMPLIANT This Biamp product including all attendant cables and accessories supplied bv Biamp meets all requirements of EU Directives 2002 95 EC of Januarv 27 2003 and 2005 618 EC of August 18 2005 the EU RoHS Directives An EU Ro
7. BIAMP Tesira TEC 1s amp TEC 1i Operation Installation Manual October 2012 Biamp Systems 9300 SW Gemini Drive Beaverton Oregon 97008 U S A 503 641 7287 www biamp com TABLE OF CONTENTS TESIRA ETHERNET CONTROL TEC 1 FEATURES lee 3 FRONT PANEL 222553328 294273 4 894 ee ooo 4 Setup and Use 4664 6 608 on CKO ESE ROOD ESO Hc OR e eC GR 9 RC ER 4 DISDIGV ua aca ROCCO UD CORE ena Oe ORC AD e E DS e 4 Capacitive touch Scroll Wheel eere 4 BACK PANEL es 5 CODI GCLOEFS so ODT 5 Sel UP qne 6 9 Device Setup Mode un 6 Edit Device ID un 7 Edit Network Configuration un 7 Edit Unlock Code un 8 Edit Display Brightness un 8 Edit Timeouts uou kx un 8 View Device Information c ncn mnhommnonmnnnmm nnnm nn 9 Reset to Factory Defaults un 9 EE 9 INSTALLATION un 10 13 TEC 1s Surface Mount Installation un 10 TEC 11 Flush Mount Installation un 11 WAITING GG Geeks ea eae eek Re ea ee ee ee le ee ee 13 SPECIFICATIONS 5 ux 0 anes eee 9 9 3X 7 97 88 58 eee oe a oo ee eee ed ee en 14 WARRANYYR uu aux os Gus ces Os eee un 15 FCO COMPLIANCE 6266646 oe sb 29 8 eke eee eee hee eee hee be a UR 16 EC DECLARATION un 17 EU RoHS COMPLIANCE ts 18 TESIRA ETHERNET CONTROL TEC 1 TEC 1 Tesira Ethernet Control is a remote control for Tesira svstems It offers a simple intuitive interfac
8. HS Materials Content Declaration document mav be obtained at www biamp com This information is presented to comply with the requirements of Chinese law SJ T11363 2006 Hazardous Substances Table Biamp Systems Corporation Remote Control Device Tesira TEC 1i TEC 1s AmA EY Buse Substances Part Name fli IK Equipment Chassis xjofjx o o Manual and Paper Documents eters ets Box and Packing Materials Jo 0 0 o lolo 0 SI T11363 2006 X SI T11363 2006 FE HAIRS A CB 0 01 91 338 EEC 76 769 EEC 0 1 1 2 0 35 3
9. e OLED panel scroll to the Display Brightness icon and press the Select button Use the scroll wheel and Select button to make adjustments The first setting represents the normal opera tional display brightness and the second setting represents the dim display brightness Display brightness cannot be assigned via Device Maintenance in the Tesira software Edit Display Brightness L Min ii Edit Timeouts To change the lock dim and sleep timeouts scroll to the Timeout icon and press the Select button Use the scroll wheel and Select button to make a selection The Timeout can range from 5 seconds to 30 minutes or none for the lock and dim timeouts the sleep timeout cannot be none Timeouts mav instead be assigned via Device Maintenance in the Tesira software Horne Hone AE TEC 1 SET UP View Device Information To view information regarding the specific unit scroll to the Information icon and press the Select button The Serial Number MAC Address Firmware Version Hostname IP Address network mask and gatewav are dis plaved This is non editable information The Serial Number is helpful in identifving phvsical units locations when naming them via Device Maintenance in the Tesira software The IP address information is useful only when TEC 1 receives an IP address automaticallv to indicate what IP address it received Use the scroll wheel to navigate through the list of information Press the Select button to exit this scree
10. e for end users and can be installed and configured to fit the unique needs of a particular application The device connects via standard Ethernet cabling and is powered over Ethernet eliminating the need for custom cabling and local power sources Multiple remote control panels can be connected over large distances using standard network technologv FEATURES Adjustment and or initiation of up to 32 selectable svstem volumes and actions Volumes are anv individual or grouped svstem levels including inputs outputs matrix cross points etc Actions are anv individual or grouped svstem operations including presets source selection mutes ducking combining etc Control functions are programmed in the Tesira svstem design software High contrast OLED Organic Light Emitting Diode displav with a wide viewing angle The displav brightness can be adjusted to fit the ambient light present in the application and can auto maticallv dim when not in use Capacitive touch technologv eliminates protruding and moving parts to increase product reliabilitv and longevitv while simplifving cleaning TEC 1s surface mounts or flush mounts to most walls with a wide variety of mounting holes to accommodate standard US and international back boxes TEC 1i flush mounts to any wall mounts using the retrofit plate included or installs in a Raco 254 box for North American installation not included 330 100m Ethernet cable length can be extended with standard
11. elect mode the cursor appears as a grav box When scrolling through the available items in the list the grav box will highlight the current selection Select mode in device setup menu On fields that can be modified use the Select button to transition to and from modifv mode In modifv mode the cursor appears as an outline box Use the scroll wheel to adjust the setting up or down Edit Unlock Code Modify mode in device setup menu Some screens have additional buttons that are used to accept OK reset or cancel changed settings Use the scroll wheel to navigate the cursor to these buttons and press the Select button The OK button saves the set ting and exits the screen The Reset button clears the setting and does not save it The Cancel button exits the screen without saving the setting TEC 1 SET UP Edit Device ID To name the unit scroll to the ID Tag icon and press the Select button Use the scroll wheel and Select button to select the desired characters Scroll to the I icon and select it to delete the previous character The default Device ID is TEC 1ID 01 The Device ID must match that of a corresponding block in the Tesira design More than one unit may be identified with the same design block same ID Device IDs may also be assigned via Device Maintenance in the Tesira software Edit Devige ID JELMHLUPGDES T Ue EE T7 EC 1ID Bi Edit Network Configuration To edit the network configuration scr
12. l to engage the latch at the bottom of the TEC 1i to detach from the trim ring Refer to page 13 for instructions regarding the use of the insulation displacement connector 12 TEC 1 INSTALLATION Connect the wire according to the color code silkscreened as text next to the IDC or as shown on the label on the back enclosure see figure below The color code uses the T568A standard for wiring When using the T568B wiring scheme please note that the orange wire pair OR and WH OR and green wire pair GR and WH GR need to be swapped After inserting the wires press the tabs until the insulation is punctured with an audible click No wire stripping is necessary GR WH BL OR BR WH GR BL WH OR WH BR IDC Silkscreen 7 y o E un Green Pair Blue Pair Orange Pair Brown Pair P Er IM Orange Pair Blue Pair Green Pair Brown Pair Insulation Displacement Connector IDC IDC wiring scheme Note the appropriate bend radius requirements for categorv cables as shown in the figure below 7025 mm 2 77 MIN DEPTH IN WALL R60 mm 2 36 MIN BEN RADIUS Software support in Tesira configuration software Version 1 1 or later provides user programming of all remote functions network setup device naming and device maintenance Visit www biamp com to obtain firmware and software updates related to this product To speak with an Applications Engineer please call 1 503 641 7287 or email support biamp com
13. n View Device Info Reset to Factory Defaults To reset to factory defaults scroll to the reset icon with the exclamation point and press the Select button To confirm scroll to the Yes button and press the Select button Otherwise selecting No will return back to the device setup screen Resetting to factory defaults clears all device maintenance parameters and restores them to their default values When resetting to factory defaults the firmware version remains unchanged Are you sure you Wart to reset ta factory defaults Exit To exit the setup screen scroll to the Exit Door icon and press the Select button TEC 1s INSTALLATION Surface Mount Installation The TEC 1s surface mounts to most walls and has a wide variety of mounting holes that accommodate standard US and international back boxes 84mm 84mm O00 i 44 313 CI USA Japan Australia EUR Italv including Germanv Sweden UK Netherlands Use a screw driver or other suitable tool to engage the latch at the bottom of the TEC 1s to detach the back enclosure When installing the TEC 1s using the RJ45 connector guide the Ethernet cable through the rear opening before attaching the TEC 1s to the wall Connect the RJ45 and snap the front enclosure into the reten tion holes When installing the TEC 1s using the IDC use a drill bit to create a hole in the top side or rear of the back enclosure along the indentations Remove the Ethernet cable jacket a
14. nd shielding Indentations Wire here for use with IDC 10 TEC 1i INSTALLATION Flush Mount Installation The TEC 1i may be flush mounted using the retrofit plate provided with the product or a Raco 254 box purchased from an electrical distributor To install the TEC 1i a hole must be cut in the wall to accommodate the Raco 254 box or to use the retrofit plate See the figures below 11 5em 4 5 8 4 3 4 12 07cm Wall cut out dimensions Mounting using a Raco 254 box Mounting using the retrofit plate TEC 1i INSTALLATION Trim Ring Exploded view showing pieces required for mounting to the retrofit plate or the Raco 254 box When installing the TEC 1i using the retrofit plate or the back box fasten the trim ring using the four screws provided to either the retrofit plate or the back box Once the trim ring has been fastened to the retrofit plate or the back box guide the TEC 1i front plate at an angle into the top of the trim ring to seat the tabs on the top of the front plate Once this has been done rotate the bottom of the front plate towards the bottom of the trim ring until it is seated in the trim ring via the bottom clip If the front plate needs to be removed use a screw driver or other suitable too
15. oll to the Network icon and press the Select button The default setting Auto allows the device to receive its network configuration from a DHCP server This allows TEC 1 to be discovered by a Tesira device that also has default settings The default hostname is TEC 1 followed by its serial number Select the hostname to edit it in a similar way of editing the device ID The network settings may instead be assigned via Device Maintenance in the Tesira software Edit Het Config Hostname TECI Auto IP Auto To specify a static IP address change the Auto IP to Static and select the IP address TEC 1 will display the Edit IP Address screen where the IP address network mask and gateway can be edited Resetting the IP address sets the IP address network mask and gateway back to 0 Edit Het Config Edit IF Address Hostname TECI 5 5 5 Huta IF nc Static IP BE Da ma m alia 1 li m CI UIN TIJEJ OJ m n TEC 1 SET UP Edit Unlock Code To set password protection scroll to the Kev icon and press the Select button Use the scroll wheel and Select button to choose the desired characters During normal operation holding down the Select button for five sec onds will lock the unit and the user will be prompted for the Lock Code before obtaining access Lock Codes may also be assigned via Device Maintenance in the Tesira software Edit Lock Code Edit Display Brightness To change the brightness of th
16. ors one rear facing RJ45 and one top facing insulation displacement connector IDC are provided for connecting to the network Only one connector may be used The RJ45 and IDC utilize unshielded twisted pair UTP wiring to connect to a Tesira system This connection is made to the Ethernet port of a Tesira unit either directly single station or via a network switch and carries control data over Ethernet The TEC 1 is powered using IEEE 802 3 2008 Power over Ethernet protocol as Class 1 devices Either a PoE capable network switch or a PoE injector is required to power the device there are no other provisions for power inlet Ethernet switch TEC 1 with PoE Ethernet switch TEC 1 without PoE PoE injector AC Power TEC 1 SET UP Device Setup Mode The TEC 1 can be configured without connecting to a functional Tesira network To enter setup mode connect the TEC 1 to a PoE source and place the jumper or anv metal object across the locksmith pins When configuration is complete remove the jumper and attach it to only one pin to resume normal operation Please note manv of the configuration settings can be accessed via the Tesira software S l 204460 M1 94V 0 a PfI NG l C24 E em V POE Locksmith Bridge jumper pins to enter ome fh AN ege ce ee ee EA setup mode The cursor has two modes select and modifv In s
17. tion by the system design software EU Directive 2002 95 EC RoHS Directive CE marked FCC 14 WARRANTV BIAMP SVSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5 VEAR LIMITED WARRANTV TO THE ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL 1 Biamp Svstems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 VEARS from the date of purchase from an authorized Biamp Svstems dealer subject to the terms and conditions set forth below 2 If you notify Biamp during the warranty period that a Biamp Systems product fails to comply with the warranty Biamp Systems will repair or replace at Biamp Systems option the nonconforming product As a condition to receiving the benefits of this warranty you must provide Biamp Systems with documentation that establishes that you were the original purchaser of the products Such evidence may consist of your sales receipt from an authorized Biamp Systems dealer Transportation and insurance charges to and from the Biamp Systems factory for warranty service shall be your responsibility 3 This warranty will be VOID if the serial number has been removed or defaced or if the product has been altered subjected to damage abuse or rental usage repaired by any person not authorized by Biamp Systems to make repairs or installed in any manner that does not comply with Biamp Systems recommendations
Download Pdf Manuals
Related Search