Installation Manual
Contents
1. T FORESPA A LEISURE FURL COASTAL IN BOOM FURLING SYSTEM SAILTEC Projekt GmbH Hasselbinnen 28 D 22969 Schenefeld 49 40 822994 0 info sailtec eu www sailtec eu Installation Manual Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL TABLE OF CONTENTS Page Number 3 Disclaimer 4 Components packing list amp required tools 5 Gooseneck bracket location 6 Installation sail track T Location of luff track top cap 8 Flexible feeder fitting instructions 9 Mainsheet and vang bail fitting 10 Initial check sail fitting amp your notes 11 IMPORTANT INFORMATION TO INSTALLERS amp OWNERS Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL IMPORTANT Read this first Installation should only be undertaken by an experienced rigger Use safety equipment and install during suitable conditions Follow the instructions in this manual Each Leisure Furl system is custom manufactured to the unique specifications of this vessel If you do not understand a point in this manual do not guess request advice We have made every effort to explain the installation process as completely as possible Nonethe less it is not possible to anticipate or address every conceivable problem that might arise during installation Hence we can not accept responsibility for2. Boom vangs amp topping lifts In boom furling systems require both a rigid boom vang and a traditional boom topping lift for safety and ease of sail trimming When furling or reefing the boom should be adjusted to the required 87 angle and held at that angle with the support of the boom vang during the furling process In heavy weather the boom topping lift should be used to arrest the motion of the boom during furling When the boat is moored a boom topping lift will extend the life of your boom vang no matter what type spring pneumatic hydraulic or electric 3 Haben Sie Fragen zum hema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL PACKING LIST Leisure furl boom Furling mandrel Gooseneck bracket assembly Luff track base extrusions Bolt rope foil sections Threaded luff slugs Feeder assembly Luff track sheave 1 4 20 machine screws Vang lug Mainsheet bails Sail cover Furling line Owner s manual Sailmaker s Instructions unless sent to sailmaker by Forespar TOOLS REQUIRED 1 4 20 taps Drill bits sizes 7 or 3 16 Hack saw Screwdriver phillips Measuring tape Center punch Tap wrench Electric drill motor Electric grinder 4 to remove the existing gooseneck bracket and fair the area Winch handle Boson s chair Lanocote or similar anti corrosion compound LocTite Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sa
3. 11 The COASTAL Leisure furl uses a two piece base and foil system The foil portion is an extrusion of UHMW PE high tensile polymer After mounting the aluminum base extrusion with the 020 space as shown below slide on the foil The foil pieces can simply be joined by butting them together Due to thermal expansion of the polymer bolt rope foil a gap of 1 must be left between the top end of the foil and the bottom of the halyard sheave box STAINLESS STEEL LINK PLATE P amp S S S SHEET METAL SCREWS BOLT ROPE FOIL 020 GAP ALUMINUM BASE EXTRUSION Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure garl COASTAL Flexible feeder limit line fitting instructions The limit line assembly consists of two stainless steel termination blocks and a fixed length of Spectra line which passes through the eye on the forward face of the luff feeder To install the limit line termination blocks on the mast position the port and starboard blocks at an equal distance from the aft face of the mast The limit line should be loose enough to allow the track to flex port and starboard but not aft With that in mind the termina tion blocks should be installed on the mast sides as shown in the diagrams 4 amp 5 The termination blocks are installed using the 1 4 20 FHMS provided use an F or 3 10 drill The knot in each end of the limit line must be pushed out of the termination block to exp
4. LIMIT LINE fo Diagram 5 Ne BOTTOM VIEW 8 Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen LSecsare farl Main Sheet and Vang Bail fitting instructions BAIL FITTING When fitting the mainsheet and vang bails in the track the bails must be secured using the special dog set screws that have been provided Be sure to pull the sail cover to the top of the boom to prevent damage from drilling into the lower cavity 1 Position the bail in the track 2 Tighten the pointed dog set screw one provided to mark the location for drilling 3 Slide the bail out of the way and drill the 9 64 hole through the top of the track 4 Position the bail using a standard dog set screw in the first hole then mark and drill the nexthole asin steps 2 amp 3 si When all the holes have been drilled for the bail use Loc Tite on the dog and the threads of each set screw and tighten The dog set screws must be used at every threaded fastening point of the bail 6 When tight the set screws force the bail tight against the underside of the track The dogs lock into the drilled holes which secures the bail against the thrust loads preventing the bail from sliding in the track T All bail set screws must remain tight Checking these screws should be a part of the regular preventative maintenance inspections on your Leisure Furl boom LOWER CAVITY AREA TOP OF TRACK DRILL THESE HOLES a
5. first section to the top of the mast and fixed it in place you can install successive sections pushing them up the mast as you progress It would be helpful to have a 4 foot and a 6 foot length of wood or electrical conduit to prop up the sections as you work The base weighs 49 Ibs ft or 25 Ibs 50 ft 8 Introduce more slugs into the mast luff slot as needed Progressively add track base sections until there is no more than 6 feet left to the bottom track mark Tighten all these sections in place making sure each joint is well aligned 9 Cut the final PVC luff track to length so the lower end is 9 above datum and tighten in place Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL 10 Refer to Diagram 3a and table below for sheave box location This is dimensioned from the center of the main halyard sheave down to the upper end of the base CENTER OF MAIN HALYARD SHEAVE extrusion SYSTEM SHEAVE TO BASE SERIES REFERENCE DIMENSION COASTAL 6 0 152mm al BASE EXTRUSION LUFF TRACK ASSEMBLY Diagram 3a NOTE Be sure that the link plate screws DO NOT enter the boltrope area of the boltrope foil The correct ard re location of the link plate will result EXTRUSION in the screws seating in the web Anchor the bolt rope foil to the Ur A aluminum base extrusion at the SLUG bottom only and allow the rest to move up and down
6. nn DOG SET I lif screw eS SHEET BAIL Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL INITIAL CHECK Ensure the furling mandrel rotates freely Ensure that boom is at correct 87 degree angle SAIL FITTING 1 Attach first the tack to the furling mandrel leaving around 1 between the tack web and tack ring Now lash the clew to the outhaul saddle on the mandrel Do not pull the foot out tight leave fullness in the foot for efficient down wind sailing The built in sail foot controls will generate outhaul tension The clew lashing must take multiple wraps around the furling mandrel to eliminate the up load on the pad eye Hoist the sail up the mast Roll the sail onto the port side of the mandrel We recommend two persons assist by pulling either the luff or leach so as to ensure the bolt rope remains in the area between the boom edge and the mast whilst the sail is being furled Leisure fell COASTAL Installation Notes 10 Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL Important information for both installers and owners e Do not raise the boom with the topping lift or vang more than 2 feet from the normal operating angle as the mandrel will bottom out on the boom aft end plate and cause damage If it is essential to do this the mandrel must
7. be disconnected from the universal e If the boom is dropped down to the deck for any reason en sure that the mandrel has not dropped off the aft end spigot before raising the boom again with the vang or topping lift e If it is necessary to furl downwind pull the boom in to 45 degrees before commencement This decreases the load in the sail gets the sail off the shrouds and spreaders and in creases the efficiency of the furl e Ifa topping lift only is being used to support the boom tie a knot in the topping lift line aft of the rope clutch or cleat to ensure that if someone accidentally releases the topping lift cleat the boom doesn t crash down and cause damage or hurt someone e Ensure all track joints are smooth and radiused The track entrance from the sail feeder is particularly important e Ensure that there is nothing on the mast in the area that the sail rolls that could possibly cause sail chafe This could include fittings around the side of the mast and trisail tracks 11 Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen
8. errors or omissions in this manual These installation guidelines are intended to provide general guidance to an experienced rigger For spe cific guidance and technical support contact the person who sold you the Leisure furl system Specific guidance and technical support are fundamental to the installation process An experienced rigger should have a thorough knowledge and understanding of general rigging installation principles These guidelines should be read in conjunction with such other principles Such principles shall be deemed to supplement these guidelines Installation of the Leisure furl system is entirely at your own risk We accept no liability for personal injury or property damage resulting from faulty installation Nor do we accept warranty claims resulting from faulty installation Do not install a Leisure furl system except on the boat for which it was specifically designed and manufactured The Vang Lug amp Sheet Bails All vang lugs and sheet bails are shipped loose and should be positioned during the installation process This allows for the most precise location of these fittings IT IS VERY IMPORTANT THAT THE SAIL COVER BE PULLED TO THE TOP OF THE BOOM PRIOR TO FASTENING THE VANG LUG AND SHEET BAILS THIS WILL PREVENT DAMAGING THE SAIL COVER DURING THE DRILLING amp TAPPING PROCESS Line controlled vangs like the Forespar Yacht Rod should be setup to raise the boom above the 87 angle when the line is released
9. iltec de oder 040 8229940 anrufen Leisure ul COASTAL LUFF il TRACK 87 REQUIRED 25 FURLING ANGLE FOOT TRACK MANDREL FURLING SPOOL 34 u Diagram 1 ITEMS NOT SHOWN Wo aga Sail Cover 7 BOTTOM OF BRACKET Luff Track Halyard Sheave i fo Furling Line Sheet Bails a r wad me Use LocTite on all gooseneck l fitting to mast fasteners Diagram 2 Note that Diagram 1 shows the location of the base extrusion 34 above the Datum point which is the center of the furling mandrel The flexible feeder portion of the sail track extends 25 below the end of the base extrusion The lower base of the P dimension is the top of the furling mandrel 1 1 2 above Datum Refer to Diagram 2 for the vertical dimensional relationship between the gooseneck bracket datum and the bottom of the boom When replacing a standard boom the Leisure furl goose neck does not need to be located where the original fitting was Considerations for desired boom location are sail hoist P dimension vang angle dodger and head clearance Remember when sailing to weather the boom can be sheeted below the 87 required furling angle Haben Sie Fragen zum Ihema Einfach ein Email an verkauf sailtec de oder 040 8229940 anrufen Leisure ul COASTAL For installation to a new vessel the positioning ofthe gooseneck will be determined as per the information on page 6 It is wise to measure P f
10. ose the fastener hole This will allow marking of the mast for drilling and tapping as well as installing and tightening the screw This may require flexing the track forward to install the second termination block A piece of light line tied around the mast and luff track may be handy here to hold the track in the forward flexed position Each installation is a little different and the desired amount of flex has to be determined by hoisting and furling the sail The furling operation should be done several times with eyes on the luff of the sail Ensure that the 87 boom angle is correct then watch as sail the rolls into the boom Furling should be checked at different angles to the wind since this is the true test of the flexible feeder setup p TRACK BASE _ S S 10 24 X 1 SCREWTO SECURE THE BOTTOMBOLT Once the termination blocks have been 6 Minimum installed on the mast the only way to effect the amount of flex in the ROPE FOIL TO THE unsupported portion of the luff track BASE EXTRUSION is to change the length of the limit line ONLY THE BOTTOM If less flex is deemed necessary the LENGTH OF BOLT ROPE f FOIL IS FIXED TO THE line can be shortened BASE If a longer line is required for additional flex Spectra FLEXABLEFEEDER line can be purchased from your local chandlery S S LUFF FEEDER a Use a figure eight stopper knot in each end then trim Diagram 4 the ends as necessary SIDE VIEW TERMINATION BLOCK _
11. rom the top of P to the bottom of P This will confirm the gooseneck position as per Diagram 1 In allinstances It would be preferable to check with the owner the preferred position because of the greater depth of the boom INSTALLATION INSTRUCTIONS fitting the sail track track slugs 1 After confirming the gooseneck position make a reference mark for the position datum which is the center of the furling mandrel 2 Measure and mark a position 34 above datum that the base extrusion will finish See Diagram 1 3 Luff track and track base must be installed before any other fittings are attached to the aft face of the mast 4 Insert 18 or more mounting slugs into the mast luff slot raise to a convenient waist level and place a piece of masking tape across slot to hold up the slugs 5 Hold the 6 track base that has the sheave box attached against the back of the mast and thread one of the 20 machine screws through the base into the top slug 6 While pushing the track base upward as you work engage a slug for each hole in the base T When the first set of slugs are installed send the first base section to the person at the masthead for tightening in place while the second track base is being prepared below Position this first section oftrack atthe top ofthe mast Refer to diagram 3a for the location in relation to the main halyard sheave 7A Alternately if you are working alone once you have raised this
Download Pdf Manuals
Related Search