novaWASH Quad LED moving head user manual
Contents
1. or Yes Pan Inverse mode Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute novaWASH Quad LED th mann MUSIC IS OUR PASSION 19 How to set the unit Tilt Inverse Back Light Display Inverse themann MUSIC IS OUR PASSION Press the MENU button up to when Tilt Inverse is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the No Normal or Yes Tilt Inverse mode Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Back Light is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the On back light on or Off back light off 1 minute after auto show mode Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Display Inverse is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the No Normal or Yes Display Inverse mode Once selected pr2. 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it into the DMX output of the last unit Connect the unit together in a daisy chain by linking the XLR plug from the output of the unit to the input of the next unit The cable cannot be branched or split to a Y cable DMX512 is a high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 and 511 usually 0 and 1 are equal to 1 The end ofthe DMX512 system should be terminated to reduce signal errors Au 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 5 Not used novaWASH Quad LED th mann MUSIC IS OUR PASSION 27 Troubleshooting 5 Troubleshooting A few common problems that may occur during operation are shown in the following Here are some suggestions for easy troubleshooting The unit does not work no light and the fan does not work Check the power connection and main fuse Measure the mains voltage on the main c
3. on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select Show 1 Show 2 Show 3 or Show 4 Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute moving head 18 Slave Mode Black Out Pan Inverse How to set the unit Press the MENU button up to when Slave Mode is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the Master Slave 1 or Slave 2 mode Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Black Out is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select either Yes device switched to dark blackout or No normal operation Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Pan Inverse is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the No Normal
4. value and press the ENTER button to store To return to the main functions without any change press the MENU button novaWASH Quad LED th mann MUSIC IS OUR PASSION 21 How to set the unit Temperature Unit Fixture Time Fixture Settings Reset themann MUSIC IS OUR PASSION Press the MENU button up to when Temperature Unit is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select C or F Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Fixture Time is blinking on the display Press the ENTER button and the display will show the number of working hours of the unit To return to the functions press the MENU button Press the MENU button up to when Fixture Settings is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select No or Yes Use the option Yes to restore all parameters of the unit with the factory settings Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Reset is blinking on the display Pres
5. Mode 1 9 Channel Mode Mode 2 18 Showt Show2 Show Mode Shows Shows Master Slave Mode Slave 1 Slave2 No Black Out Yes No Pan Inverse Yes No Tiltinverse Yes Off Back Light On No Display Inverse Yes Auto Test Pan Tilt Red Green Manual Test 0 255 Blue White Strobe Dimmer Red White Balance Green 125 255 Blue Temperature Unit e F Fixture Time No Fixture Settings Yos Reset novaWASH Quad LED How to set the unit themann MUSIC IS OUR PASSION 17 How to set the unit DMX Address Channel Mode Show Mode themann MUSIC IS OUR PASSION Press the MENU button up to when DMX Address is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to change the DMX512 address Once the address has been selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Channel Mode is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to select Mode 1 9 or Mode 2 16 Once selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Press the MENU button up to when Show Mode is showing up
6. c shock Strobe lighting can trigger seizures in photosensitive epilepsy Sensitive persons should avoid looking at strobe lights WARNING Risk of burns The surface of the device can become very hot during operation Do not touch the device with bare hands during operation and after switching off wait for at least 15 minutes novaWASH Quad LED th mann MUSIC IS OUR PASSION Safety instructions NOTICE Risk of fire Do not cover the device nor any ventilation slots Do not place the device near any direct heat source Keep the device away from naked flames NOTICE Operating conditions This device has been designed for indoor use only To prevent damage never expose the device to any liquid or moisture Avoid direct sunlight heavy dirt and strong vibrations themann moving head MUSIC IS OUR PASSION 10 Safety instructions NOTICE Power supply Before connecting the device ensure that the input voltage AC outlet matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker Failure to do so could result in damage to the device and possibly injure the user Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire novaWASH Quad LED th mann MUSIC IS OUR PASSION 11 How to set the unit 3 How to set the unit themann MUSIC IS OUR PASSION Unpack and
7. carefully check that there is no transportation damage before using the unit Keep the equipment packaging To fully protect the device against vibration dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage respectively Establish all connections as long as the unit is switched off Use the shortest possible high quality cables for all connections WARNING Risk of injury caused by falling objects Make sure that the installation complies with the standards and rules that apply in your country Always secure the device with a secondary safety attachment such as a Safety cable or a safety chain moving head 12 How to set the unit NOTICE Risk of overheating Always ensure sufficient ventilation The ambient temperature must always be below 40 C 104 F NOTICE Use of stands When mounting the device onto a stand ensure that the stand is in a safe and stable position and that the weight of the device does not exceed the maximum permissible load capacity of the stand novaWASH Quad LED th mann MUSIC IS OUR PASSION 13 How to set the unit 3 1 Control panel Display Shows the various menus and the selected functions LEDs DMX On DMX input present MASTER On Master mode SLAVE On Slave Mode POWER On Power input present themann moving head MUSIC IS OUR PASSION 14 How to set the unit Buttons MENU To selec
8. ee novaWASH Quad LED moving head themann MUSIC IS OUR PASSION user manual Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany Telephone 49 9546 9223 0 E mail info thomann de Internet www thomann de 30 04 2014 ID 255359 Table of contents on aw General notes unnunenseesensssensennssennssennnsennsennne Safety instructions How to set the unit ueseeeeneensenneeneeneenne 3 1 Control panel u nassssessensssenseesenssenssseusseunsseen 3 2 Main functions sresesseesersvesserssessvsserssrsssrssrses How to control the unit neseeneen 4 1 DMX controller nssrssrsssssssersserssssssrnsersssrssessssenses 4 2 DMX512 configuration 4 3 DMX512 connectiOn srsssrssrsssesvasvesserserserserserseer Troubleshooting snersrinservssvevssevnseresseveseresserrsseensseres Fixture cleaning unnneeneennnseennnneennn Technical specifications unesssenenee Protecting the environment nsvonosssnnssvnnssssenssernnn novaWASH Quad LED Table of contents themann MUSIC IS OUR PASSION General notes 1 General notes Symbols and signal words themann MUSIC IS OUR PASSION This user manual contains important information on safe operation of the device Read and follow all safety notes and all instructions Save this manual for future reference Make sure that it is available to all persons using this device I
9. ess the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute moving head 20 How to set the unit Auto Test Press the MENU button up to when Auto Test is showing up on the display Press the ENTER button and the display will show Test and the unit will run a self test To return to the func tions press the MENU button Manual Test Press the MENU button up to when Manual Test is showing up on the display Press the ENTER button and PAN will blink Use the UP and DOWN buttons to choose Tilt Red Green Blue White Strobe or Dimmer Press the ENTER button to enter then press the UP or DOWN buttons to adjust the value and press the ENTER button to set the next option To return to the main functions without any change press the MENU button White Balance Press the MENU button up to when White Balance is showing up on the display Press the ENTER button and RED will blink Use the UP and DOWN buttons to adjust the value Press the ENTER button to store and Green will blink on the display Press the UP and DOWN buttons to adjust the value Press the ENTER button to store and Blue will blink on the display Press the UP and DOWN buttons to adjust the
10. f this device through an approved waste disposal firm or through your local waste facility When discarding the device comply with the rules and regulations that apply in your country If in doubt consult your local waste disposal facility novaWASH Quad LED th mann MUSIC IS OUR PASSION 33 Notes themann moving head MUSIC IS OUR PASSION 34 Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany www thomann de
11. f you sell the device to other users be sure that they also receive this manual Our products are subject to a process of continuous development We therefore reserve the right to make changes without notice This section provides an overview of the symbols and signal words used in this user manual moving head Signal word DANGER WARNING NOTICE Warning signs A A General notes Meaning This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a pos sible dangerous situation that can result in death or serious injury if it is not avoided This combination of symbol and signal word indicates a pos sible dangerous situation that can result in material and environmental damage if it is not avoided Type of danger Warning high voltage Warning hot surface novaWASH Quad LED th mann MUSIC IS OUR PASSION General notes Warning signs Type of danger Warning suspended load N Warning danger zone themann moving head MUSIC IS OUR PASSION Safety instructions 2 Safety instructions Intended use Use the device only as described in this user manual Any other use or use under other oper ating conditions is considered to be improper and may result in personal injury or property damage No liability will be assumed for damages resulting fr
12. lt Speed Pan Tilt Macro IN 255p Slow 236 255 Macro12 216 235 Macro11 196 215 Macro10 176 195 Macro 9 156 175 Macro 8 136 155 Macro 7 116 135 Macro6 096 115 Macro 5 076 095 Macro 4 056 075 Macro 3 036 055 Macro 2 016 035 Macro 1 000 015 Stop How to control the unit Special Function 240 255 Stand alone 200 209 Reset 80 89 Disable blackout while pan or tilt move 70 79 Enable blackout while pan or tilt move ob Fast Ed S ARA 100 0 255 100 255 255 100 0 novaWASH Quad LED 255 100 0 255 p 100 0 255 192 255 Color Fade 1 16 128 191 Color Macro 1 16 8 127 Color 1 32 0 7 themann MUSIC IS OUR PASSION How to control the unit 4 3 DMX512 connection DI DI Qe ar cf N NA V N IHN A N RAT HSH EG GEN HO HOP R A NA h WAT N FASZA f I Vesey NN NCW IN VII NY lt A Sf lt Y lt gt AL Li AV DP DMX Controller Ground DMX Input Gi DMX DMX Output DMX Termination reduces signal errors and prevents signal transmission problems and interference It is always advisable to insert Q a terminating resistor 120 ohm 0 25 W lt Q between pin 2 DMX and pin 3 DMX of the last unit themann moving head MUSIC IS OUR PASSION 26 How to control the unit At the last unit the DMX cable has to be terminated with a terminator Solder a
13. om improper use This device may be used only by persons with sufficient physical sensorial and intellectual abilities and having corresponding knowledge and experience Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety Safety DANGER Danger for children Ensure that plastic bags packaging etc are disposed of properly and are not within reach of babies and young children Choking hazard Ensure that children do not detach any small parts e g knobs or the like from the unit They could swallow the pieces and choke Never let children unattended use electrical devices novaWASH Quad LED th mann MUSIC IS OUR PASSION Safety instructions DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Never remove any covers There are no user serviceable parts inside DANGER Electric shock caused by short circuit Always use proper ready made insulated mains cabling power cord with a pro tective contact plug Do not modify the mains cable or the plug Failure to do so could result in electric shock death or fire If in doubt seek advice from a regis tered electrician themann moving head MUSIC IS OUR PASSION Safety instructions WARNING Eye damage caused by high light intensity Never look directly into the light source WARNING Risk of epilepti
14. onnector aaa Check the power on LED Not responding to DMX con troller The DMX LED should be on If not check the DMX connectors and cables to see if they are properly linked LE If the DMX LED is on and there is no response to the channel check the address settings and DMX polarity themann moving head MUSIC IS OUR PASSION 28 Troubleshooting 3 If you have intermittent DMX signal problems check the pins on connectors or on the PCB of the unit or of the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside high voltage cables that may cause damage or interference to DMX interface circuit One of the channels is not working well The cable connected to the PCB may be broken If the procedures recommended above do not succeed please contact our Service Center You can find the contact information at www thomann de novaWASH Quad LED th mann MUSIC IS OUR PASSION 29 Fixture cleaning 6 Fixture cleaning themann MUSIC IS OUR PASSION The cleaning of internal and external optical lenses and or mirrors must be carried out periodi cally to optimize light output The cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumu lation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the
15. parts carefully M Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days moving head 30 Technical specifications 7 Technical specifications Through its flexible installation options the unit can be installed in various orientations It is perfect for professional stage theatre TV exhibition and architectural applications DMX channels 9 16 channels Voltage AC 100 240 V 50 60 Hz Power consumption 300 W Light source 22 x 10 W CREE quad color LED Fuse 5 A slow characteristic Beam angle 36 Dimensions 404 8 mm x 236 8 mm x 335 3 mm 15 9 in x 9 3 in x 13 2 in Weight 9 5 kg 20 9 Ibs novaWASH Quad LED th mann MUSIC IS OUR PASSION 31 Technical specifications moving head Protecting the environment 8 Protecting the environment Disposal of the packaging mate rial For the transport and protective packaging environmentally friendly materials have been chosen that can be supplied to normal recycling Ensure that plastic bags packaging etc are properly disposed of Do not just dispose of these materials with your normal household waste but make sure that they are collected for recycling Please follow the notes and markings on the packaging Disposal of your old device This product is subject to the European Waste Electrical and Electronic Equipment Directive WEEE Do not dispose with your normal household waste Dispose o
16. s the ENTER button and all motors will return to their home position To return to the functions press the MENU button moving head 22 How to control the unit 4 How to control the unit You can operate the unit in three ways 1 _ By the built in preprogrammed function 2 By the universal DMX controller 4 1 DMX controller Using the universal DMX controller to control the units you have to set the DMX address from 1 to 512 channels so that the units can receive the DMX signal Press the MENU button up to when DMX Address is showing up on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to change the DMX512 address Once the address has been selected press and keep the ENTER button to store To return to the functions without any change press the MENU button or wait for one minute novaWASH Quad LED th mann MUSIC IS OUR PASSION 23 How to control the unit 4 2 DMX512 configuration 9 Channel DMX512 Configuration Mode 1 Ch5 Ch6 255p 100 255 100 255g 100 255100 255p 100 240 255 Slow Stand alone 200 209 Reset fast close 80 89 Disable blackout while pan or tilt move 16 131 55 70 79 g Enable blackout while pan or tilt move ok 0 oL 0 ob 0 ok 0 themann moving head MUSIC IS OUR PASSION 24 16 Channel DMX512 Configuration Mode2 Pan Fine Ch5 Tilt Fine Pan Ti
17. t the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions Fuse For over current protection Mains input Connect to supply mains power DMX input output For DMX512 link use 3 5 pin XLR plug cable to link the unit together novaWASH Quad LED th mann MUSIC IS OUR PASSION 15 How to set the unit 3 2 Main functions themann MUSIC IS OUR PASSION To select any of the given functions press the MENU button up to when the required one is showing up on the display Select the function by the ENTER button and the display will blink Use the DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to store To return to the main functions without any change press the MENU button or wait for one minute Hold the MENU button to quit the menu mode The unit will run the built in program you selected The main functions are shown below moving head 16 MENU DMX Address 1 512
Download Pdf Manuals
Related Search