PCCOM USER MANUAL - Decision
Contents
1. 2 Select Receive Mode JP2 JP4 J gt 3 3 The JP2 and JP4 are used to select receive mode To short 1 2 means select receive always enable and short 2 3 means select RTS to enable receive The JP2 is used to select receive mode for port 1 and the JP4 is used to select receive mode for port 2 Jumper Receive always enable Enable by RTS JP2 for port 1 Short 1 2 Short 2 3 JP4 for port 2 Short 1 2 Short 2 3 aaa DECISION Computer International 3 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 3 Select High Speed or Normal Speed Mode JP5 JP6 J k The JP5 and JP6 are used to select high speed mode or normal speed mode the clock is 7 3728MHZ for high speed mode and 1 8432MHZ for normal speed mode For high speed mode the baud rate speed up to 460K The JP5 is used to select speed for port 1 and the JP6 is used to select speed for port 2 wi Ma k kwi Pa k Jumper Normal Speed High Speed JP5 for port 1 Short 1 2 Short 2 3 JP6 for port 2 Short 1 2 Short 2 3 Pin Clock Rate Mode Short 1 2 1 8432MHZ Normal Speed Short 2 3 7 3728MHZ High Speed 4 Card Identifier The switch is used to identify card number default setting is card 15 There are two methods to set the card number aaa DECISION Computer International 2 Operations Manual a PnP mode PCCOM PCI 2 RS2. By multiplexing a serial line there are two sorts of data channels for TTY data by dev ttyXYY and TP data by dev IpXYY If the dev ttyj11 is used for a TTY it has to be enabled before you would like to print data through dev Ipj11 to a printer that connected to the terminal that is operated via dev ttyj11 The channel for TP data that is uni directional is used to transmit the data from a host to a terminal only The differentiates of TTY data and TP data in the same serial line is that TP data are encapsulated within a couple of PRINT ON and PRINT OFF escape strings that are recognized by connected terminals The PRINT ON and PRINT OFF is defined by connected terminals The scheme to multiplex a serial line for these two channels is based on time division method The time slices for TTY or TP data are generated according to the entry procedure polling in the PCCOM driver which is periodically called by system clock The period of system clocks is different among various operating systems e g most UNIXs is 100hz but SCO Xenix is 50hz The interval reserved for TTY or TP channel in the same serial line is important to output TP data to a low speed printer through high throughput line from PCCOM cards if there is no flow control XON XOFF to the serial line aaa DECISION Computer International 23 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card tL a l l N a j The lpx command is used to adjust the time interval
3. Select high speed mode or normal speed mode for port 1 JP6 Jumper 6 Select high speed mode or normal speed mode for port 1 SW1 Switch 1 Identifies card number DECISION Computer International PCCOM PCI 2 RS422 RS485 Isolator card Operations Manual SE REE REE REE EERE EERE EERE EERE EEE 10206066 190 sayndwoy vere se 3 2 1 yoy voso u POOL ARAL Soe 050619d eseeeeail emen o tie Ce eesecoenn E ii ecccecen asis E 46000004 e n SR Bl Je sung 10400059 le gt MT rrer ld 0 da a el _ msm g fon fan ORO yl occ comil us eeeeecseeseesoseeeonti row off ME S OoOO Cee eee mic mee eT pare 8 E tdr OOOO AB CY o a AAA AAA AAA AAA AAA h eae ET OSSIA ii eecoestin BE 6 E eeeeeeeeeeeeeoeeeeeee Sus eeee W p31 jeuopeuse3uy 10 ndwo9 NOISsIg3a sy aaa DECISION Computer International Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 1 Select RS422 or RS485 Mode JP1 JP3 2 3 The JP1 is used to select RS422 or RS485 for port 1 and the JP3 is used to select RS422 or RS485 for port 2 To short pin 1 2 means select RS422 mode otherwise to short pin 2 3 means select RS485 mode be Pa m Jumper RS422 RS485 JP1 for port 1 Short 1 2 Short 2 3 JP3 for port 2 Short 1 2 Short 2 3
4. c pci opt For high speed DEVICE PCCOMH SYS c pci opt The syntax of PnP function is P Card_id Portno Port The Card_id field is defined as 1 or 2 or 3 or 4 or nil if you use PnP mode just fill nil in card_id field that like step 1 otherwise you can Se DECISION Computer International 17 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 specify card_id to match the card identifier switch The Portno field is used to specify number of ports in this adapter The Port field is defined as PCCOM V2 0 5 If more than one PCCOM board is installed Please repeat directive P of the step 1 aaa DECISION Computer International 18 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 APPENDIX C UNIX CONFIGURATION The distribution CD contains SCO UNIX driver Our drivers also provide transparent printer features that let user to connect local printer from auxiliary port of terminal The PCI BIOS will assign card number automatically when you use PnP method otherwise you can use card identifier switch to set your card number The software installation procedures are shown is the bellows C 1 Hardware Configuration 1 First adapter Port Device Name MODEM Name Transparent Printer Name 1 dev ttyj11 dev ttyJ11 dev Ipj11 dev ttyj12 dev ttyJ12 dev Ipj12 2 Second Adapter Port Device Name MODEM
5. Name Transparent Printer Name 1 dev ttyj21 dev ttyJ21 dev lpj21 dev ttyj22 dev ttyJ22 dev lpj22 aaa DECISION Computer International 13 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 3 Third Adapter Port Device Name MODEM Name Transparent Printer Name 1 dev ttyj31 dev ttyJ31 dev lpj31 dev tty 32 dev ttyJ32 dev lpj32 4 Fourth Adapter Port Device Name MODEM Name Transparent Printer Name 1 dev ttyj41 dev ttyJ41 dev Ipj41 dev ttyj42 dev ttyJ42 dev lpj42 C 2 Software Installation i The installation procedure for the device drivers is described as follows O Login as a root user O Insert distribution CD which contains device drivers into CD ROM drive d then copy the files from the distribution CD to a temporary directory cd doscp d dc tz dc tar Z zcat de tar tar xvfp To install device drivers please type aaa DECISION Computer International 20 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 cd usr sys pccom dc install O Reboot the system Now your new UNIX system that includes device drivers is activated Enable each terminal by using the enable command enable ttyj11 enable ttyj12 O Connect each terminal to connector NOTE O If the new system fails to reb
6. RS422 RS485 ports for asynchronous communications e Provides isolator function which can isolate voltage up to 2500V r m s e Suitable for SCO UNIX Linux MS DOS WINDOWS NT 2000 XP WINDOWS 95 98 ME OS 2 etc e Pentium hardware compatibles e Baud rate up to 115200 for normal speed mode and up to 460K for high speed mode e Provides 16550 port that contains 16 bytes FIFO for each port e Upto 4 boards be installed in one computer system e Software compatible with PCCOM98 2000 e Operating temperature 0 to 60 C e Storage temperature 20 to 70 degree C e Humidity 5 to 95 in non condensing DECISION Computer International Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card te l N l N a l l N a j CHAPTER 2 UNPACKING INFORMATION Check that your PCCOM package includes the following items PCCOM PCI bus 2 RS422 RS485 with isolator adapter User manual Decision Studio CD for PCCOM software Warranty form DECISION Computer International Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 CHAPTER 3 SYSTEM REQUIREMENTS Before installing your PCCOM PCI bus 2 port adapter make sure that e The host computer is a Pentium or its compatibles e The switch and the jumpers are properly configured e The operating system you intend to use is capable of driving multiple serial ports DECISION Computer International 4 Operations Manual PCCOM PC
7. RS422 standard The signal assignments for a standard DB25 connector are shown below Pin Description Transmit Data TxD Receive Data RxD Chassis Ground GND 20 Transmit Data TxD 22 Receive Data RxD aaa DECISION Computer International 1A Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card BE REE REE REE EERE ERE REE ERE EERE EEE APPENDIX A PC COM DIAGNOSTIC UNDER MS DOS The TESTCOM is a diagnostic program provide routines to test your PCCOM PCI 2 port serial adapter under MS DOS It has both internal and external loop back tests During external loop back test a loop back plug must be connected to each port being tested You can also select different hardware settings during testing from the SETUP RS232 RS422 menu User can get TESTCOM program from Decision Studio CD i To test your PCCOM 2 port adapter under MS DOS please type TESTCOM The TestCom menu will appear Setup RS232 RS422 is used to setup the baud rate etc Internal loop test is used to test the IC External loop test is used to test the ports Auto is used to test the IC and the ports of the card aaa DECISION Computer International a Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card E i N h l l h R l R l l a a M M l M a M l R l N M l a a l N l N a N M N a j APPENDIX B PC COM DEVICE DRIVER FOR MS DOS B 1 PCCOM Software The PCCO
8. are clearly marked with an RA number that has been issued by DECISION Goods returned without this authorization will not be attended to aaa DECISION Computer International 20
9. 422 RS485 Isolator card BEE ERE EEE EERE EERE EERE ERE ERE ERE EERE EEE EEE Just plug in PCCOM PCI bus 2 port adapter into PCI slot the PCI BIOS will allocate I O address to each adapter automatically and assign card number start from 0 to each adapter You may set any card number at PnP mode and you need use software tools to distinguish port id Almost all of the operating systems run at PnP mode b manual mode Set card number by card identifier switch the PCI BIOS will assign pre allocated I O address to each adapter Please set different card number to each adapter do not duplicate card number setting Card Number 1 2 3 4 OFF OFF OFF OFF 15 ON OFF OFF OFF 14 OFF ON OFF OFF 13 ON ON OFF OFF 12 OFF OFF ON OFF 11 ON OFF ON OFF 10 OFF ON ON OFF 9 ON ON ON OFF 8 OFF OFF OFF ON 7 ON OFF OFF ON 6 OFF ON OFF ON 5 ON ON OFF ON 4 DECISION Computer International 10 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card BE EEE REE ERE EEE REE EERE EERE EERE ER OFF OFF ON ON ON OFF ON ON OFF ON ON ON Cole NI Ww ON ON ON ON The card number starts from 0 to 15 aaa DECISION Computer International AL Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 CHAPTER 6 RS422 RS485 CABLING INFORMATION 6 1 RS422 Cabling Information for DB9 The communication interface follows the EIA RS422 sta
10. I 2 RS422 RS485 Isolator card 2000000000000 CHAPTER 4 HARDWARE INSTALLATION Your PCCOM PCI bus 2 port adapter is designed to be inserted in any available PCI slot in your Pentium or compatibles You must plug this board to your computer before installing PCCOM software In order to gain access to the expansion slots follow the steps listed below 1 A DECISION Computer International Turn off all power to your computer and all peripheral devices before installing your PCCOM PCI bus 2 port adapter Remove the cover of the computer Insert the PCCOM PCI bus 2 port adapter into any available PCI slot Make sure the adapter is firmly seated in the chosen slot Replace the cover of the computer Connect cables to DB9 connectors as required Turn on the power of your computer Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 CHAPTER 5 SWITCH AND JUMPER SETTING The Plug and Play features let hardware configuration for IRQ and VO address is detected by BIOS automatically so that it need not switch and jumper setting However the on board switches can be used to identify card number by the users if you do not set the switch the PnP BIOS will assign card number automatically JP1 Jumper 1 Select RS422 or RS485 mode for port 1 JP2 Jumper 2 Select receive mode for port 1 JP3 Jumper 3 Select RS422 or RS485 mode for port 2 Select receive mode for port 1 IPS Jumper 5
11. M software is a high performance easy to use RS232 RS422 device driver for PC 486 Pentium or compatibles Under MS DOS environment you can set up your serial ports by PCCOM device driver and these serial ports can be treated as COM1 and COM2 devices The setup procedure provides flexible functions to specify the configuration of multi serial card that is the hardware configurations of I O port number I O port address interrupt and interrupt vector are user selectable After the device driver is installed It takes over communication between CPU and multi serial cards such as four port card eight port card etc For each I O port the service routine handles a ring buffer to keep track of all I O data Moreover the PCCOM software provides library routines C PASCAL BASIC FoxPro and DOS communication interface DOS device driver BIOS call for several access levels For more details please refer PCCOM manual aaa DECISION Computer International t6 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card E i N h A l h R l N a l l l l l l M a M l R l N M l a a l N l N a N l N a j B 2 Software Installation When the board is installed please install software drivers as follows STEP 1 Prepare PCI OPT file The PCI OPT file contents are B 4 D COM3 P 2 2k 9600 N 8 1 RTS DTR XON 2 STEP 2 Prepare CONFIG SYS file Insert statement into CONFIG SYS file For normal speed DEVICE PCCOM SYS
12. Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card tL a M M N a j CHAPTER 1 INTRODUCTION The PCCOM PCI bus 2 port RS422 RS485 with isolator adapter is an 32 bits PCI bus board with Plug and Play PnP features it provides two asynchronous serial communication ports RS422 RS485 which link the computer and serial peripheral devices such as terminals modems serial printers plotters etc The on board isolator can isolate voltage up to 2500V r m s The PCCOM PCI bus 2 port adapter is particularly suited to facilitate the connection of terminals VDUs in multi user operating systems The PCCOM board may be installed in any Pentium or hardware compatible systems The PnP features let hardware configuration for IRQ and I O address is detected by BIOS automatically you don t need set switch and jumper Since most of the computer has its own COM1 and COM2 the PCCOM PCI bus 2 port adapter can be configured from COM4 On board 16550 chip provides two 16550 functions which contains 16 bytes FIFO buffer for each 16550 ports There are two kinds of mode can be choose one is normal speed mode that its baud rate up to 115200 another is high speed mode that its baud rate up to 460K DECISION Computer International Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 The features of the PCCOM PCI bus 2 port RS422 RS485 adapter are e 32 bit PCI bus with Plug and Play PnP features e Two
13. PCI 2 RS422 RS485 Isolator card 2000000000000 whatever you type must appear to the textbox as long as you have a loop back on the COM port of your card H 2 Using Decision Terminal To test the card using the Decision Terminal Please do the following steps 1 Install the software using the Decision Studio It is inside the CD AutoOpen program 2 Run the program Decision Terminal at the program menu of the start menu 3 Setup the COM port properties by selecting the setup option on the File menu 4 You can now begin to type any message to transmit textbox Take note that whatever you type must appear to receive textbox as long as you have a loop back on the COM port of your card 5 You can also click the Test button to test your card automatically aaa DECISION Computer International 24 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 APPENDIX I SOFTWARE DEVELOPMENT INFORMATION In the Decision Studio CD it contains PCCOM device driver for WINDOWS 3 1 95 98 2000 NT ME XP DOS OS 2 UNIX Linux and the development tools for serial communication and telecommunication 1 1 PCCOM Professional The PCCOM Professional is the Serial Communication Software Development Tool Kits Under Windows 95 98 2000 NT ME XP It contains Complete OCX and DLL Microsoft Win32 API software accessory function for application software developer It is an easy to use tool and speed up serial communica
14. card SETSERIAL dev cua4 AUTO_IRQ autoconfig STD_FLAGS SETSERIAL dev cua5 AUTO_IRQ autoconfig STD_FLAGS aaa DECISION Computer International ee Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card BE REE REE ERE EEE REE EERE EERE EERE ER APPENDIX H DIAGNOSTIC UNDER WINDOWS After installing the PCCOM PCI bus 2 port adapter to your computer you can test it if it is functioning correctly via HyperTerminal a Windows package communication program or by using the Decision Terminal a software of the Decision Computer International Co Ltd included on the CD Just make sure that there is a loop back plug connected to the COM Port under test H 1 Using Hyper Terminal To test the card using the Hyper Terminal Please do the following steps 1 Run the HyperTerminal program 2 During connection the program will ask you to enter your name and choose an icon for the connection Enter any name and select any icon 3 After entering your name and selecting icon you will be ask for country code area code phone number and connect using what Ignore all edit box except for the connect using click the combo box and select Direct to COMx You can use any port but usually the COM1 and COM2 is used by the computer motherboard 4 Put the proper COM x properties 5 You can now begin to type any message Take note that aaa DECISION Computer International 23 Operations Manual PCCOM
15. d in the user manual Furthermore that the PCCOM product will be supplied free from defects in materials and workmanship and be fully functional under normal usage aaa DECISION Computer International ds Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 In the event of the failure of a PCCOM product within the specified warranty period DECISION will at its option replace or repair the item at no additional charge This limited warranty does not cover damage resulting from incorrect use electrical interference accident or modification of the product All goods returned for warranty repair must have the serial number intact Goods without serial numbers attached will not be covered by the warranty Transportation costs for goods returned must be paid by the purchaser Repaired goods will be dispatched at the expense of PCCOM To ensure that your PCCOM product is covered by the warranty provisions it is necessary that you return the Warranty card Under this Limited Warranty DECISION s obligations will be limited to repair or replacement only of goods found to be defective as specified above during the warranty period DECISION is not liable to the purchaser for any damages or losses of any kind through the use of or inability to use the PCCOM product DECISION reserves the right to determine what constitutes warranty repair or replacement Return Authorization It is necessary that any returned goods
16. et by just specifying its email address Remote Access Server This development tool use to dial up like and phone dialer technology able to dial an ISP and monitor some of some IP address on network aaa DECISION Computer International oe Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 APPENDIX J WARRANTY INFORMATION J 1 Copyright Copyright DECISION COMPUTER INTERNATIONAL CO LTD All rights reserved No part of PCCOM software and manual may be reproduced transmitted transcribed or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of DECISION COMPUTER INTERNATIONAL CO LTD Each piece of PCCOM package permits user to use PCCOM only on a single computer a registered user may use the program on a different computer but may not use the program on more than one computer at the same time Corporate licensing agreements allow duplication and distribution of specific number of copies within the licensed institution Duplication of multiple copies is not allowed except through execution of a licensing agreement Welcome call for details J 2 Warranty Information DECISION warrants that for a period of one year from the date of purchase unless otherwise specified in the warranty card that the goods supplied will perform according to the specifications define
17. for TTY or TP data and the TP protocol lpx option device name e option t number set interval for TTY l number set interval for Transparent Printer n string set esc string to turn on printer f string set esc string to turn off printer T get interval for TTY L get interval for Transparent Printer N get esc_string to turn on printer F get esc_string to turn off printer e device_name IpXYY The range of interval reserved for TTY or TP channel is from 1 to maximum integer The default setting for any dev IpXYY is as follows Interval for TT Y 50 Interval for TP 1 PRINT ON escape 1033 51 ESC 51 PRINT OFF escape 033 41 ECS 41 The examples to invoke Ipx O Set 60 time slices reserved for dev ttyj11 aaa DECISION Computer International 24 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 Ipx t 60 dev ttyj11 O Set 2 time slices reserved for dev lpj11 Ipx 12 dev lpj11 Get the time slices reserved for dev Ipj11 Ipx L dev Ipj11 O Set PRINT ON string for dev Ipj11 Ipx n 033 51 dev Ipj11 Get PRINT OFF string for dev Ipj11 Ipx F dev Ipj11 1033 4i aaa DECISION Computer International 25 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 APPENDIX D WINDOWS95 98 CONFIGURATION Welcome to the Decisi
18. ndard The signal assignments for a standard DB9 connector are shown below Pin Description 1 Chassis Ground GND 4 Transmit Data TxD 5 Transmit Data TxD 8 Receive Data RxD 9 Receive Data RxD To connect the RS422 to other DATA TERMINAL EQUIPMENT DTE devices the developers recommend using a DTE to DTE connection as shown below HOST REMOTE Chassis Ground Chassis Ground Transmit Data Receive Data Receive Data Transmit Data Transmit Data Receive Data Receive Data Transmit Data aaa DECISION Computer International 12 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 6 2 RS485 Cabling Information for DB9 The RS485 signal assignment is shown as follows Pin Description 1 Signal Ground 4 Transmit Data TxD 5 Transmit Data TxD 8 Receive Data RxD 9 Receive Data RxD The RS485 communication is based on cable sharing method which is connected as following Computer at site 1 Computer at site 2 TRD TRD TRD TRD Ground Ground Where TRD means short pin 4 and pin 8 at connector side and TRD means short pin 5 and pin 9 at connector side You must short both pins by yourself aaa DECISION Computer International 13 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 6 3 RS422 Cabling Information for DB25 The communication interface follows the EIA
19. ng the PCI card Inside the Control Panel you will see the Icon of Decision PCCOM Adapters indicating that the driver has been successfully installed 8 Double click the Icon Decision PCCOM Adapters another window will appear on screen and will display an installed card with corresponding COM port aaa DECISION Computer International 28 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 If you need install more than one card please run above procedure again Never try to install 2 or more cards at the same time for you will have errors in installation E 2 Remove Ports 1 Go to Control Panel Applet W Decision PCCOM Adapters 2 Select the port you want to remove then press Remove Port to delete specified port Reboot for changes to take effect aaa DECISION Computer International sa Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card Le APPENDIX F WINDOWS NT CONFIGURATION V3 5 up Welcome to the Decision PCCOM PCI cards series This series enables you to utilize the built in plug and play functionality of Windows NT combined with the power of PCI based serial communication F 1 Installation 1 For optimum PnP functionality please install one card at a time 2 Unplug your PC open it and install one Decision PCCOM PCI card 3 Start your computer and wait until Windows NT is loaded 4 Insert the device driver CD into your computer The CD is auto run so you jus
20. on PCCOM PCI cards series This series enables you to utilize the built in plug and play functionality of Windows 95 98 combined with the power of PCI based serial communication D 1 Installation 1 For optimum PnP functionality please install one card at a time 2 Unplug your PC open it and install one Decision PCCOM PCI aaa 26 card Start your computer and wait until Windows 95 98 is loaded Windows 95 98 will detect the new PCI card that is installed in your computer and will prompt you for a proper driver Insert the device driver CD into your computer and make sure Windows 95 98 finds the drivers by eventually browsing through the directory structure of the CD After installing the core device drivers for the PCI card Windows 95 98 will detect and install software for each COM port on the card This may take 5 to 10 seconds per port After Windows 95 98 has detected and configured all ports you may begin using the PCI card To verify that the installation process completed successfully please proceed into the Control Panel System Device Manager Locate the additional COM ports in the ports section If you need install more than one card please run above procedure again Never try to install 2 or more cards at the same time for you will have errors in installation DECISION Computer International Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card Le D 2 Remove Ports 1 Go to Control Panel A
21. onality provided by all data acquisition products Decision Industrial Control Develop a program controlling the Industrial digital and analog cards remotely at any part of the world using the Internet technology Done it in your application program or via Internet browser It extends Decision Industrial Interface from single computer development environment to client server development environment Remote Voice Long distance call will not be expensive as before There is no cheaper way to talk to your friend from another country than to talk through Internet And the good news is that you can develop your own software with Remote sound aaa DECISION Computer International ae Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card Le Remote Chat This development tool is used for chatting communicating with another computer in the Internet Intranet Remote White Board This development tool uses client server remote drawing board every client can shared their image drawn on server drawing board Remote Image Capture This development tool allows you to capture images taken from the CCD camera via Internet Pinger This development tool make it possible for you to make a program that check if your still connected to the network or internet and check the speed of the response of your connection Internet Location Server This development tool is used to find an IP address of a particular client computer in the Intern
22. oot please boot the original system When system is boot please press return key to halt autoboot then type sunix old O To remove device driver from UNIX please type a login as a root user b cd usr sys pccom de c Remove PCCOM Driver from the kernel remove aaa DECISION Computer International 21 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card te a l l l N a M l N l N M l R a l N M N a N l N a j After installation please enable each port by enable command and disable port by disable command disable ttyj11 O To change baud rate please update etc inittab and etc conf cf d init base files C 3 Option for High Speed The configuration of High Speed Baud Rate card is change as follows Original Extensible 50 75 110 57 6 K 134 76 8 K 150 115 2 K 200 153 6 K 300 230 4 K 600 460 8 K 1200 1200 unchanged 2400 2400 unchanged 4800 4800 unchanged 9600 9600 unchanged EXTA 19200 unchanged EXTB 38400 unchanged aaa DECISION Computer International 22 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 C 4 Transparent Printer The default device names to Transparent Printer TP are dev IpXYY that is the prefix name is changed from tty to Ip but the other XYY is the same e g under default device names the corresponding TTY line of dev lpj11 is dev ttyj11
23. pplet System Device Manager Ports 2 Select the port you want to remove then press Remove to delete specified port Reboot for changes to take effect aaa DECISION Computer International al Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 APPENDIX E WINDOWS2000 CONFIGURATION Welcome to the Decision PCCOM PCI cards series This series enables you to utilize the built in plug and play functionality of Windows 2000 combined with the power of PCI based serial communication During the boot up of Windows 2000 the hardware will be automatically detected by the WINDOWS 2000 just ignore this dialog box by clicking cancel and during login use the administrator user name for installation E 1 Installation 1 For optimum PnP functionality please install one card at a time 2 Unplug your PC open it and install one Decision PCCOM PCI card 3 Start your computer and wait until Windows 2000 is loaded 4 Windows 2000 will detect the new PCI card that is installed in your computer and will prompt you for a proper driver 5 Insert the device driver CD into your computer and make sure Windows 2000 finds the drivers by eventually browsing through the directory structure of the CD 6 After installing the core device drivers for the PCI card Windows 2000 will detect and install software for each COM port on the card 7 After Windows 2000 has detected and configured all ports you may begin usi
24. t wait until Decision Studio Applet appears 5 Click Device Drive button Windows Operating System then a selection of windows operating system platform appears 6 Click Windows NT button to view the device list of different hardware products 7 Select PCCOM Multi Port Serial Card Install Shield will do installation for you just click Next When windows prompts you to resume installation procedure 8 To configure go to Control Panel Decision PCCOM Adapters Click the of the card you want configure then select which COM port you want to set F 2 Remove Ports Go to Control Panel Ports then select what you want to remove and click Delete to remove ports aaa DECISION Computer International o Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 F 3 Uninstall Enter Control Panel Decision PCCOM Adapter and click Completely Remove Driver aaa DECISION Computer International 31 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 APPENDIX G LINUX CONFIGURATION The PCCOM PCI bus 2 port adapter can be installed in the Linux by using serial device driver supported by Linux For more details please refer to setserial man pages Please uncomment the appropriate lines in etc rc d rc serial to enable auto configuration of PCCOM PCI bus 2 port card For example uncomment the following lines for PCCOM PCI bus 2 port
25. telephone or portable phone 3 Send and receive E MAIL 4 Send and receive FAX 5 Receive DTMF I 4 PCCOM RemoTeleCom The PCCOM Remote TeleCom is an OCX programming development tool for made application software That will use to enhance PCCOM TeleCOM functions Pager E mail Voice mail Fax through Internet or Intranet by stand alone program or by browser through World Wide Web WWW under Windows 95 98 2000 NT ME XP User may call OCX functions to communicate with Remote devices both Server and Client using Internet communication or encapsulate OCX function and remote ActiveX Control then run development application program under Internet browser IE and Netscape aaa DECISION Computer International 28 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card tL a N l N a j I 5 PCCOM SCOPE PCCOM SCOPE is a software that monitors all the data and signals between two interacting devices or a single device With PCCOM SCOPE you can transform your PC into a total RS 232 analyzer without the need of expensive hardware or plug in boards PCCOM SCOPE creates an unsurpassed tool for RS 232 device driver communications protocol and traffic analysis 1 6 REMOTE CONTROL SOFTWARE We also provide other hardware with complete Internet Intranet remote control software tool for more function availability Decision Industrial Interface The Decision Industrial Interface was created to provide a standard way to access the functi
26. tion application software development time and cost Wide compatibility range hardware support for PCCOM multiport serial card and any standard port and support Zmodem and Kermit file transfer protocols for ASCII Text and Executable file 1 2 PCCOM RemoteCom The PCCOM RemoteCom is an OCX programming development tool for made application software That will use to enhance RS 232 422 serial communication through Internet or Intranet by stand alone program or by browser through World Wide Web WWW under Windows 95 98 2000 NT ME XP User may call OCX functions to communicate with RemoteCOM both Server and Client using Internet communication or encapsulate OCX function and remote serial ActiveX Control then run development application aaa DECISION Computer International 35 Operations Manual PCCOM PCI 2 RS422 RS485 Isolator card 2000000000000 program under Internet browser IE and Netscape I 3 PCCOM TeleCom The PCCOM TeleCom is an OCX software accessory suitable for software engineer to develop application program under Windows 95 98 2000 NT ME XP environment It really makes computer and communication application combine together Wide compatibility range hardware support for PCCOM multiport serial card and any standard port The PCCOM TeleCom software kit supports five major telecommunication functions which can be used to 1 Send message to PAGER BB Call 2 Send and receive VOICE MAIL from computer to
Download Pdf Manuals
Related Search