Home

ASPECT 2000D USER MANUAL

image

Contents

1. 1 Press Timing 2 Turn the rotary knob until the cursor points to Y C 3 Press Select 4 Turn the rotary knob until the cursor points to Pos H 5 Press Select 6 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Pos H to the desired position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 29 4 1 8 Input horizontal Chroma Position Adjustment of the horizontal input chroinance timing Range 2370ns 2296ns in steps of 74ns 1 luminance pixel Via Menu SOO NOOR ON gt 0 Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to Timing Press Select Turn the rotary knob until the cursor points to C to Y Press Select Turn the rotary knob until the cursor points to C Pos H Press Select Adjust by turning the rotary knob Via Shortcut OnPRWON gt Press Timing Turn the rotary knob until the cursor points to C to Y Press Select Turn the rotary knob until the cursor points to C Pos H Press Select Adjust by turning the rotary knob Via Remote Control Software 1 2 Open the window Proc Amp adjust Ch Pos H to the desired position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 30 ASPECT 2000D User Manual 4 1 9 Input vertical Position Adjustment of the vertical input timing luminance ch
2. 13 6 1 Operating the Audio Routing The system contains a audio routing matrix which gives the capabilty to freely rearrange the audio channels on the output This function is only available via the Remote Control Via Menu n a Via Shortcut n a Via Remote Control Software Open the window Audio Output The routing matrix is organized in four tabs SDI XLR DV Monitor The available input channels are located leftside the output channels at the bottom The colour coding of the groups conforms to the gain level and delay windows Underrneath the matrix checkboxes for the muting are arranged ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 132 ASPECT 2000D User Manual 13 6 2 Audio Embedder Sequence In general the arrangement of the audio channels in the ancilliary data space allows a high degree of flexibility But in the meantime very few configurations have been established as industrie standards The ASPECT 2000D provides two different embedding sequences Sequence A allows the support of different sampling rates for the two channel pairs within one audio group This is a special arrangement which sometimes may lead to incompatibility with external de vices Sequence B allows only one sample rate per audio group It is a more common arrangement which should be selected as default Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Tur
3. 9 4 Aspect amp Zoom Background COlOT 1 cseeeeeeeee 71 9 4 1 Output background color zoom area 71 9 4 2 Output background color crop area 72 9 5 Aspect amp Zoom Preset ccceeeeeeeeeeeeeeeeeeeeeee 73 9 5 1 Recalling a Aspect amp Zoom default Setup Predefinition cccccceseeeeeeseeeeeeeeeeeeeeeeeees 73 9 5 2 Recalling a local Aspect amp Zoom Preset 74 9 5 3 Saving a local Aspect amp Zoom Preset 75 10 WSS VI Wide Screen Signaling Video INGO XING piinaa auraka araail 10 1 Introduction 00 e cece settee eee eeeee tees eeeeeeeneeeeeeeseeeeeeeeeeees 10 1 1 Output WSS enable cecceeseeeeeeetseeeees 10 1 2 Output VI enable eee 10 1 3 Output WSS VI status OSD 10 2 WSS VI Preset iiien aiaei 10 2 1 Recalling a WSS VI default Setup Predefinition ccccccceseeceeeeeeeeeeeeeeeeeeeeees 81 10 2 2 Recalling a local WSS VI Preset 00 82 10 2 3 Saving a local WSS VI Preset eee 83 ASPECT 2000D User Manual 11 Video Signal Processing 2 00 84 11 1 General FUNCTIONS 2 2 cceeeeceeeeeeeeeeeeeeeeeeeeeeeeeee 84 11 1 1 Filter erable cece eeeeeceeeeeeeeenseeeeeeeeeenees 85 11 2 Enhancement Aperture Correction 86 11 2 1 Horizontal Vertical Enhancement 87 11 2 2 Coring Enhancement cccceeeeeeeeeeeeeees 88 11
4. Enables insertion of WSS for 50Hz formats on the system output Via Menu Press Menu Turn the rotary knob until the cursor points to WSS VI Press Select Turn the rotary knob until the cursor points to WSS OUT Turn the rotary knob to switch between On and Off meo m a Via Shortcut n a Via Remote Control Software 1 Open the window Wide Screen Signalling WSS amp Video Indexing VI 2 Select WSS On or Off in the signalling field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 79 10 1 2 Output VI enable Enables insertion of VI on the system output Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to WSS VI 3 Press Select 4 Turn the rotary knob until the cursor points to VI OUT 5 Press Select 6 Turn the rotary knob to switch between On and Off Via Shortcut n a Via Remote Control Software 1 Open the window Wide Screen Signalling WSS amp Video Indexing VI 2 Select VI On or Off in the signalling field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 80 ASPECT 2000D User Manual 10 1 3 Output WSS VI status OSD Enables the display of WSS VI data Via Menu Press Menu Turn the rotary knob until the cursor points to WSS VI Press Select Turn the rotary knob until the cursor points to Status OSD Press Select Turn the rotary knob to switch between On and Off D Or EO N
5. 6 set hours by turning the rotary knob 7 Press Select 8 set minutes by turning the rotary knob 9 Press Select 10 set seconds by turning the rotary knob 11 Press Select 12 set frames by turning the rotary knob 13 Press Select 14 confirm the setting ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 172 ASPECT 2000D User Manual 15 4 5 Keyboard setting of the generator dropframe mode Via Menu Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to generator Press Select Turn the rotary knob until the cursor points to dropframe Press Select set ON or OFF by turning the rotary knob Shortcut Press timecode Turn the rotary knob until the cursor points to generator Press Select Turn the rotary knob until the cursor points to dropframe Press Select set ON or OFF by turning the rotary knob ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 173 15 5 Timecode Display 15 5 1 Introduction The timecode decoded by the reader as well as the output of the generator can be displayed via the on screen display OSD on the selected video output refer to the OSD setting 15 5 2 Timecode Display Enable Via Menu ONOOPWN gt Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob u
6. OO GON Via Shortcut 1 Press the corresponding key in the input field 2 the menu will show Autosel 3 Press Select 4 Select ON OFF Via Remote Control Software 1 Open the window Input 2 select the desired status in the field Autoselect ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 18 ASPECT 2000D User Manual 3 1 3 Manual Input Standard Selection Normally one would use the automatic standard selection But under special circumstances e g instable input signal it can be usefull to set the input standard manually It is not possible to select the standard manually as long as the automatic is ON A The vertical frequency of the output signal will follow the input Via Menu Press Menu Turn the rotary knob until the cursor points to Input Press Select Turn the rotary knob until the cursor points to Standard Press Select Select the desired standard If it is not possible to select a standard manually please check whether automatic selection is enabled 7 The system may need up to 1sec to detect the incoming standard OO ON Via Shortcut 1 Press the key STD in the input field 2 Select the desired standard If it is not possible to select a standard manually please check whether automatic selection is enabled 3 The system may need up to 1sec to detect the incoming standard Via Remote Control Software 1 Open the window Input 2 select the desired stan
7. UMASPECT2000D 001 Rev ASPECT2000D 001 12 ASPECT 2000D User Manual 1 6 Using the Remote Control Software The Remote Control Software supports all the functions of the system It allows a very intuitive and well arranged presentation of the functions in use 1 6 1 Device Registration on the PC To connect the PC to a system there are two possibilities Scanning all the serial interfaces available on the PC In the main menu 1 1 please click Devices and afterwards scan Now the software checks all available serial interfaces on the presence of a system The procedure can be observed looking at the device list If only one system is detected the software automatically connects Adding an interface manually In the main menu 1 1 please click Devices and afterwards Add The window Add Port 1 2 appears Please select the desired serial interface set it to 38 400baud and click Add Now the software checks the selected port reads out the type of system and its name and connects ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 13 1 6 2 Device selection on the PC The software is capable to administer more than one device All windows and their positions are stored independently for the different instances To select a specific system please use the main menu 1 1 and click on Devices Out of the list se lect the desired s
8. ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 44 ASPECT 2000D User Manual 6 2 3 Genlock Termination 75 Ohm Genlock Input terminated Hi Z Genlock Input not terminated Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Genlock 3 Press Select 4 Turn the rotary knob until the cursor points to Term 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut 1 Press the Genlock key in the rightmost field 2 Turn the rotary knob until the cursor points to Term 3 Press Select 4 Turn the rotary knob to selct the desired status Via Remote Control Software 1 Open the window Genlock 2 change setting as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 6 3 Genlock Preset 6 3 1 Recalling a local Genlock Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Genlock 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut 1 Press the Genlock key in the rightmost field 2 Turn the rotary knob until the cursor points to Preset 3 Press Select 4 select the desired setting via the rotary knob Via Remote Control Software 1 Open the window
9. Press Select adjust the factor using the rotary knob DOBRO Via Shortcut 1 Press Zoom 2 adjust the factor using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 adjust the factor in the zoom setting field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 58 ASPECT 2000D User Manual 9 2 2 Manual adjustment of the output aspect ratio Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Aspect Press Select adjust the factor using the rotary knob AarRwns Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 adjust the factor in the zoom setting field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 59 9 2 3 Manual adjustment of the output horizontal zoom Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to ARC 3 Press Select 4 Turn the rotary knob until the cursor points to Zoom H 5 Press Select 6 adjust the factor using the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 adjust the factor in the zoom setting field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 60 ASPECT 2000D User Manual 9 2 4 Manual adjustm
10. chrominance or Y C adjust the noise reduction factor to the desired value when switching between Y C and Y C the systems keeps the different settings ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 91 11 4 Noise Reduction Nonlinear Filter Median Filter Nonlinear filter dedicated to impulse noise dropouts digital noise scratches The median Filter consists out of three combined filters Filter A is dedicated to horizontal vertical structures while Filter B focuses on diagonal structures Each Filter can be set up separately with a 2 or 3 dimensional aperture The 3 dimensional aperture uses three succeeding frames on the time axis The filters allow the setting of anm individual threshold The outputs of the two filters are combined by a third 3 point median filter As third component it uses the original value This structure allows very powerful and versatile algorithms The filter can be setup separately for luminance and chrominance if necessary 11 4 1 Median Filter Factor A Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to VidProc 3 Press Select 4 Turn the rotary knob until the cursor points to Median 5 Press Select 6 Turn he rotary knob to Y luminance or C chrominance or Y C both components 7 Press Select 8 Turn he rotary knob to Factor A 9 Press Select once to setup the threshold twice to setup 2D 3D 10 Turn
11. 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 175 15 5 4 Timecode reader vertical display position Via Menu ONAAR WN gt lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to display Press Select Turn the rotary knob until the cursor points to rd pos V Press Select set the desired vertical position of the reader display by the rotary knob Shortcut OOTP O Via Press timecode Turn the rotary knob until the cursor points to display Press Select Turn the rotary knob until the cursor points to rd pos V Press Select set the desired vertical position of the reader display by the rotary knob Remote Control Software 1 2 Open the window timecode select the desired display position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 176 ASPECT 2000D User Manual 15 5 5 Timecode generator horizontal display position Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to display 5 Press Select 6 Turn the rotary knob until the cursor points to gen pos H 7 Press Select 8 set the desired horizontal position of the generator display by the rotary knob Via Shortcut 1 Press timecode 2 Turn the rotary knob until the cursor points to display 3 Press Select 4 Turn th
12. 3 Open the window Preset click on Save for the desired global preset in the global preset field the current global status of the system will be saved ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 182 ASPECT 2000D User Manual 16 2 2 Recalling of a global Preset Via Menu Press Menu Turn the rotary knob until the cursor points to Preset Press Select Turn the rotary knob until the cursor points to Pres Press Select Turn the rotary knob until the cursor points to the desired position OOT E Via Shortcut 1 Press Preset 2 Turn the rotary knob until the cursor points to Pres 3 Press Select 4 Turn the rotary knob until the cursor points to the desired position Via Remote Control Software 1 Open the window Preset 2 click on load for the desired global preset in the global preset field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 183 16 2 3 Assigning a name to a global Preset This function is supported only by the Remote Control Software The assigned name will also be displayed in the keyboard display Open the window Preset for the desired Preset click on Rename assign the desired name click Rename Pons ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 184 ASPECT 2000D User Manual 16 3 Backup and Restore of Presets on the remote PC Using the Remote Control Software it is possible to bachup and
13. ARE ofar awey wy Aj E F ose ueg Ala Zzp ainjanys Buydwes ala UOHEWOJUI oy sawe wy splay OAplA ala UONEWIOJU oN play 1007 ala uonewojul oN s5ejj aainos ala uonewojul ON Bunayj4 Alfa uonewojul op A PWWeE g ajfa uonewiojui oN 1e sanewnd aauasajay ala uonewojul o Buiposua 10 07 ala UOHEWOJUI ON Woy jeuBis Alfa EXP PE 65 525 ways s BuIuUeds bwHapuy oapl sayygns uado oN apow Buijygns a433 uya sapgns oN yxa 9I9 uipi sapngng d al Jadjay On Jadia H Supoa jeuonussuog Guipos moog g a a apow eiaweg w4 yewo n E F aqe one yadsy bwjeubis uaalos apii Indino o woo o wL o ae awe usj o ueg uonewojul oN ainjanys Buydwes UOHEWOJUI op fsawes wy SPjay OAPI uonewojul ON pay 10109 UONEWIOJUI oN sBey aanog uonewojul oN Bunad uonewojui oy uoneznuenb ajdueg uonewojul oN uonenba ewweg uonewojui ON Ue sanewnd aauaiajay uonewojul oN Guiposua 1007 uonewojul o woj euis UONHEWOJUI ON wajs s BUIUUEDS TENCE sayngns uado oN apow Buipngng ajaja uim sapygns oyf isayajay WILY sapngng Jadjay on Guipos jeuonuaauog Gurpos mojo7 apow eiaweg wil yewo nd Eip jage one yadsy bwjeubig Uasog apli INANI sadja H IA SNDXGONI OJIA 8 SSM ONITYNOIS NIJYIS JAM ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 78 ASPECT 2000D User Manual 10 1 1 Output WSS enable
14. Genlock 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 46 ASPECT 2000D User Manual 6 3 2 Saving a local Genlock Preset Up to 4 local prest configurations can be stored as user 1 user 4 Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Genlock 3 Press Select 4 Turn the rotary knob until the cursor points to Save Preset 5 Press Select 6 select the desired Preset via the rotary knob 7 Press Select Via Shortcut 1 Press the Genlock key in the rightmost field 2 Turn the rotary knob until the cursor points to Save Preset 3 Press Select 4 select the desired Preset via the rotary knob Via Remote Control Software 2 Open the window Genlock 3 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 47 7 Test Pattern 7 1 Test Pattern The system is equipped to provide a wide selection of standard test patterns The following patterns are available Black Color Bars for 50Hz and 60Hz PAL NTSC IWQ Bar 60Hz only Red 2T ITU Multiburst ITU 2T20T ITU Line 330 50Hz only ITU Line 331 50Hz only ITU Line 17 Field 1 60Hz only ITU Line 17 Field 2 60Hz only C Ramp Test Patterns are activated and selected in two steps Test Pattern activation This function switches between the selected Test Pattern and the video
15. ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 16 3 1 1 ASPECT 2000D User Manual Input Source The ASPECT 2000D supports the following input sources a DV Firewire IEEE1394 There is one connector available for both input and output If the DV source is not selected it automatically acts as an output The DV interface supports DVCAM and DVCPro b Digital components conforming to SMPTE 259M 272M Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Input 3 Press Select 4 Turn the rotary knob until the cursor points to Source 5 Press Select 6 select the desired source Via Shortcut 1 Press the corresponding key in the input field 2 The desired input will be selected immediately Via Remote Control Software 1 Open the window Input 2 select the desired input 3 The desired input will be selected immediately ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 17 3 1 2 Automatic Input Standard Selection The system is able to detect the supported standards automatically This feature can be switched off if desired Please note The vertical frequency of the output signal will always follow the conditions on the input Via Menu Press Menu Turn the rotary knob until the cursor points to Input Press Select Turn the rotary knob until the cursor points to Autosel Press Select Select ON OFF
16. Press Select 4 Turn the rotary knob until the cursor points to C Pos V 5 Press Select 6 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Ch Pos V to the desired position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 32 ASPECT 2000D User Manual 4 2 Preset Proc Amp 4 2 1 Recalling a Proc Amp default Setup Predefinition The default Setup provides a common reset to the Proc Amp functions Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to Predef Press Select Select default by turning the rotary knob Oarhwn gt Via Shortcut n a Via Remote Control Software 1 Open the window Proc Amp 2 Select default in the PRE Definition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 4 2 2 Recalling a local Proc Amp Preset 33 work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Procamp 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Proc Amp 2 change setting in the Preset field as desi
17. Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window color correction 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 106 ASPECT 2000D User Manual 11 7 3 Saving a local color correction Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to color 3 Press Select 4 Turn the rotary knob until the cursor points to Save Preset 5 Press Select 6 select the desired Preset via the rotary knob 7 Press Select Via Shortcut n a Via Remote Control Software 1 Open the window color correction 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 12 Legalizer 12 1 Introduction The ASPECT 2000D includes a fully programmable RGB legalizer OPERATION ON GLOBAL yj USER v DEFAULT UPPER LEGALIZER ALL 12 1 1 Legalizer Enable This allows to bypass the legalizer block without affecting its setting Via Menu Press Menu Turn the rotary knob until the cursor points to Legalizer Press Select Turn the rotary knob until the cursor points to Operation Press Select select ON or OFF
18. Via Menu Press Menu Turn the rotary knob until the cursor points to VBI Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select SOD Or PN gt Via Shortcut n a Via Remote Control Software 1 Open the window VBI 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 54 ASPECT 2000D User Manual 9 Aspect Ratio Conversion ARC and Zoom 9 1 Introduction To simplify the standard workflow the ASPECT 2000D provides predefined format settings For this reason normally it is not necessary to calculate the parameters for the common formats If the there are special requirements which demand the adjustment of parameters there impact is additive For example if a zoom factor of 1 0 is selected the input format is 4 3 full format and the output format shall be 16 9 anamorph the system automatically calculates and applies the appropriate parameters But if the image should be shrinked to half of its size in horizontal and vertical direction just apply a zoom factor of 0 5 No further settings will be influenced With additional parameters like Pan Scan Crop it is the same situation For the crop function therefore under some special cicumstances even negative values may occur ARC Input Control The aspect ratio conversion can be setup manually or using control information
19. a Via Shortcut n a Via Remote Control Software 1 Open the window Wide Screen Signalling WSS amp Video Indexing VI 2 Select On or WSS or VI in the show status in OSD field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 81 10 2 WSS VI Preset 10 2 1 Recalling a WSS VI default Setup Predefinition Via Menu Press Menu Turn the rotary knob until the cursor points to WSS VI Press Select Turn the rotary knob until the cursor points to predef Press Select Select the desired setting by turning the rotary knob D O E O Na Via Shortcut n a Via Remote Control Software 1 Open the window Wide Screen Signalling WSS amp Video Indexing VI 2 Select the desired predefinition ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 82 ASPECT 2000D User Manual 10 2 2 Recalling a local WSS VI Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to WSS VI 3 Press Select 4 Turn the rotary knob until the cursor points to preset 5 Press Select 6 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Wide Screen Signalling WSS amp Video Indexing VI 2 change setting in the Preset field as desired ModelASPECT2000
20. cursor points to C C Bal Press Select Adjust by turning the rotary knob AakRwns Via Shortcut 1 Press C Bal 2 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Bal Cb Cr to the desired ratio ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 25 4 1 4 Input Black Level pedestal Video black is defined in NTSC and Pal M 7 5 above the blanking level In PAL PAL N and SECAM it is 0 This setup is only available for NTSC NTSC 4 43 and PAL M Adjustment of the input black level Range 11 4 11 4 in steps of 1 Available for all sources Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to Bk Level Press Select Adjust by turning the rotary knob DOV ONS Via Shortcut 1 Press Black Level 2 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Bk Level to the desired value Blanking Level ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 26 ASPECT 2000D User Manual 4 1 5 Input Offset Cp Adjustment of the input chrominance offset Cb Range 11 4 11 4 in steps of 1 o Available for all sources Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob unti
21. ete eiiees tei eee 12 1 INtrOCUCTION ccccceeceeeseeeeeeeeeseeeeeeeeeeeeeeeeeneeeneenees 12 1 1 Legalizer Enable 12 1 2 Legalizer upper limit 12 1 3 Legalizer lower limit 12 2 Preset LegaliZer cccccesssseceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeae 12 2 1 Recalling a Legalizer default Setup Predefinition cccccceeeceeeeeeeeeeeeteeeeeneeees 110 12 2 2 Recalling a local legalizer Preset 0 111 12 2 3 Saving a local legalizer Preset 08 112 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 13 Audio Processing ssseseeeeeeeeeees 113 13 1 INtrOCUCTION cccceceeseteeeeeeeeeeeeeeeeeeseeeeeeeeeeeeeeenaees 113 13 2 AUGIO INP Ub iescccccsicesseccsceecsasscsenacceecscseeeeeseeedeeaetecete 115 13 2 1 Input Mute a2 23 02 00vececeestese ds ek eh decdes 115 13 2 2 Audio Input Master Level ccssccccceeeeeees 116 13 2 3 Audio Input Gain amp Level ccccceeeeeeeee 117 13 2 4 Audio Input XLR select analog AES 118 13 2 5 DV Audio Resampling Input ee 119 13 2 6 DV Audio Input channel select 08 120 13 3 Preset Audio Input ccse sesseeeeeeeseeeneeeeneeees 121 13 3 1 Recalling a Audio Gain default Setup Predefinition 2 cstscesvestvs aeceeati deteseiala Selden 121 13 3 2 Recalling a Audio Level default Setup Predefinition cccccceccceeees
22. in the window lowerlegalizer 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 110 ASPECT 2000D User Manual 12 2 Preset Legalizer 12 2 1 Recalling a Legalizer default Setup Predefinition The default setup provides a common disable to the legalizer Via Menu Press Menu Turn the rotary knob until the cursor points to legalizer Press Select Turn the rotary knob until the cursor points to Predef Press Select Select default by turning the rotary knob DEDS Via Shortcut n a Via Remote Control Software 1 Open the window legalizer 2 Select default in the PRE Definition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 12 2 2 Recalling a local legalizer Preset 111 work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to legalizer 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window legalizer 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 112 ASPECT 2000D User Manual 12 2 3 Saving a local legalizer Preset Up to 4 local preset configura
23. included in the input signal The system supports WSS and VI as formats for the input control information Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to active format Press Select Turn the rotary knob until the cursor points to in auto Press Select Turn the rotary knob to the desired mode OFF or WSS or VI ONOOPWN gt Via Shortcut Press Aspect Turn the rotary knob counter clockwise to in auto Press Select Turn the rotary knob to the desired mode OFF or WSS or VI PON gt Via Remote Control Software Open the window Aspect ratio conversion and Zoom 2 select the desired mode in the active format field 3 If no valid input format can be detected the parameter is marked as red ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 55 9 1 2 Manual selection of the input format The input format can only be selected manually if the input control iss et to OFF Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to ARC 3 Press Select 4 Turn the rotary knob until the cursor points to active format 5 Press Select 6 Turn the rotary knob until the cursor points to input 7 Press Select 8 Turn the rotary knob clockwise counter clockwise to the desired format Via Shortcut 1 Press Aspect twice 2 Turn the rotary knob clockwise counte
24. knob until the cursor points to DV Press Select Select the desired configuration by turning the rotary knob ONAARWN gt Via Shortcut n a Via Remote Control Software 1 Open the window audio output 2 Select the tab DV 3 Select the desired configuration in the Predefinition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 139 13 7 4 Recalling a local output Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to audio 3 Press Select 4 Turn the rotary knob until the cursor points to output 5 Press Select 6 Turn the rotary knob until the cursor points to Preset 7 Press Select 8 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window audio output 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 140 ASPECT 2000D User Manual 13 7 5 Saving a local audio output Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to output Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the d
25. of BNC type This input is dedicated to connect LTC timecode sources as Beta cam or external timecodegenerators It supports levels conforming to SMPTE und EBU The connector is of BNC type Supports miniDV DV DVCAM or DVCpro sources A 6 pin IEEE1394 or Firewire connector is used Bidirectional SDI input conforming to SMPTE 259M 272 M The connectors are of BNC type Accepts Blackburst or Composite Video The connectors are of BNC type used to connect the system with an external PC or Network Inter face Sub D 9 pin female plug The unit supports 4 independant analog audio channels The first channel is located leftside besides the power connector rear view The audio connectors use mini XLR plugs Standard output levels are calibrated to OdBu 15dBfs Connector assignment Input 1 Audio 1 left channel Input 2 Audio 1 right channel Input 3 Audio 2 left channel Input 4 Audio 2 right channel Two output connectors for AES EBU or S PDIF signals are provided The first output is located left rear view besides the analog audio The connectors are of BNC type This output is dedicated to connect LTC timecode destinations as Betacam It supports levels conforming to SMPTE und EBU The connector is of BNC type SDI output conforming to SMPTE 259M 272 M BNC connector ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 1 3 Power Rear Panel R
26. on the input and output This enables the system to follow the geometric conditions of the input signal The content of the received WSS VI data packets can be displayed by the onscreen menu or via the remote control software on a computer monitor WSS VI is also provided for the system output So the outgoing signal can be labelled with the appropri ate information If enabled the input of the ASPECT 2000D locks to the conditions signalled by the WSS or VI data It follows on a frame by frame base without delay and disturbance VI Video Line Index Video Line Index data as defined by SMPTE RP186 is used to encode programme and picture related source information in conjunction with a component digital video signal The data is encoded in the chrominance signal on lines 11 324 for a 50Hz signal or on lines 14 277 for a 60Hz signal It is dedicated to digital transmission formats and gets discarded when converted to analog WSS WSS is an alternative solution for signalling aspect ratio and related information conforming to ITU BT1119 It uses an analog waveform to carry the data and is located in the first half of line 23 for 50Hz formats The advantage is that it withstands D conversion and so normally will pass through analog and digital systems ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 77 ASPECT 2000D User Manual SNOLLINIGIO Tad jE gaso E SCR aE ser woz afa pref m
27. prevents the user from accidentily loosing lip sync When operating the system in non auto mode please keep in mind that the video delay may vary with the mode of operation Via Menu ONONRPWN gt Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Delay Press Select Turn the rotary knob until the cursor points to Autodelay Press Select Select ON or OFF Via Shortcut PWON gt Press Audio Delay Turn the rotary knob until the cursor points to Autodelay Press Select Select ON or OFF Via Remote Control Software 1 Open the window Audio Delay click Auto in the master delay field This is a toggle function When yellow automatic delay is en abled ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 126 ASPECT 2000D User Manual 13 4 2 Audio Master Delay The master delay allows the common adjustment of the delay of all output channels If the automatic delay is selected it shows the current system delay Adjustment of the master delay is only possible when not in auto mode Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Delay Press Select Turn the rotary knob until the cursor points to Delay Press Select Adjust the delay using the rotary knob CO Od OB O2 NO Via Shortcut 1 Press Audio Delay 2 Turn t
28. slider besides the input window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 67 9 3 5 Output Cropping top Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to Out Upper Press Select Adjust the Cropping using the rotary knob ONAARWN gt Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to Out Upper 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the cropping by the appropriate slider besides the input window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 68 ASPECT 2000D User Manual 9 3 6 Output Cropping bottom Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to Out Lower Press Select Adjust the Cropping using the rotary knob ONAAP ON Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to Out Lower 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the crop
29. the cursor points to Preset 7 Press Select 8 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window audio processing 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 124 ASPECT 2000D User Manual 13 3 4 Saving a local audio input processing Preset The local Preset covers level and gain settings Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to processing Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select OONAARON gt Via Shortcut n a Via Remote Control Software 1 Open the window audio processing 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 13 4 Audio Delay There are various possibilities to setup the delay of an audio channel common delay adjustment for all channels allows delay adjustment channel by channel automatically corrects the delay of the video path Master delay Channel delay Automatic delay 13 4 1 Audio Auto Delay 125 It is recommended to enable the automatic delay correction as a default setting This
30. the rotary knob to adjust the parameter for orthogonal structures Via Shortcut n a Via Remote Control Software Open the window Video Signal Processing Select Y C separate adjustment of luminance chrominance or Y C select the threshold for orthogonal structures when switching between Y C and Y C the systems keeps the different settings PONS ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 92 ASPECT 2000D User Manual 11 4 2 Median Filter Factor B Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to VidProc 3 Press Select 4 Turn the rotary knob until the cursor points to Median 5 Press Select 6 Turn he rotary knob to Y luminance or C chrominance or Y C both components 7 Press Select 8 Turn he rotary knob to Factor B 9 Press Select once to setup the threshold twice to setup 2D 3D 10 Turn the rotary knob to adjust the parameter for diagonal structures Via Shortcut n a Via Remote Control Software PO Nes Open the window Video Signal Processing Select Y C separate adjustment of luminance chrominance or Y C select the parameter for diagogonal structures when switching between Y C and Y C the systems keeps the different settings ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 93 11 5 Filter Preset 11 5 1 Recalling a Filter default Setup Predefinition The default setup pr
31. the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to adj post white and the desired color all red green blue Press Select turn the rotary knob to adjust to the desired value aRWN gt M Via Shortcut n a Via Remote Control Software 1 Open the window Color Correction 2 click on the upper right symbol in the window postwhitelevel 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 102 ASPECT 2000D User Manual 11 6 6 Color Correction post black level The settings can be made independantly for each color or alternatively for all three colors in the same man ner The Remote Control Software gives a better overview so this first step is not necessary Via Menu Turn the rotary knob until the cursor points to Color Press Select Turn the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to adj post black and the desired color all red green blue Press Select turn the rotary knob to adjust to the desired value aRWN gt ao Via Shortcut n a Via Remote Control Software 1 Open the window Color Correction 2 click on the upper right symbol in the window postblacklevel 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 103 11 6 7 Color Correcti
32. the rotary knob until the cursor points to inserter 5 Press Select 6 Turn the rotary knob until the cursor points to RP188 7 Press Select 8 Turn the rotary knob until the cursor points to OUTPOS 9 Press Select 10 select the desired line Via Shortcut 1 Press Timecode 2 Turn the rotary knob until the cursor points to reader 3 Press Select 4 Turn the rotary knob until the cursor points to RP188 5 Press Select 6 Turn the rotary knob until the cursor points to OUTPOS 7 Press Select 8 select the desired line Via Remote Control Software 1 Open the window Timecode 2 activate the extended window 3 select the desired line in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 165 15 3 8 Timecode inserter DV TC activate Enable of the DV TC insertion into the outgoing DV signal The distribution of time code data into the DV stream is defined by the IEEE standard So Via no further line selection is necessary Menu 0 ON OO ONS lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to DV TC Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Shortcut ONOORWN gt Via 1 2 3 Pres
33. until the cursor points to Cursor 3 Press Select 4 Turn the rotary knob until the cursor points to Pos Upper 5 Press Select 6 select the position by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect Ratio Conversion amp Zoom 2 select the desired position for Cursor 1 or Cursor 2 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 146 ASPECT 2000D User Manual 14 1 6 Cursor position vertical bottom Numbers given as lines field Via Menu Press Menu Turn the rotary knob until the cursor points to Cursor Press Select Turn the rotary knob until the cursor points to Pos Lower Press Select select the position by turning the rotary knob DOT EONS Via Shortcut n a Via Remote Control Software 1 Open the window Aspect Ratio Conversion amp Zoom 2 select the desired position for Cursor 1 or Cursor 2 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 147 14 1 7 Cursor Mode Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Cursor 3 Press Select 4 Turn the rotary knob until the cursor points to Mode 5 Press Select 6 select the desired shape by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect Ratio Conversion amp Zoom 2 select the desired shape in the cursor settings field ModelASPECT2
34. your CD DVD drive In most cases an explorer window will appear which shows the content of the CD If this should not be the case please select and open the CD manu ally Select the folder Software and click on setup exe Please wait until the installation program has been started Click on proceed Select the folder for the installation or accept the proposed folder and click on proceed Select the name for the start menu or accept the proposal and click on proceed Now the installation software shows the current setup Please confirm with proceed The software will be installed Please wait until the process is completed Click on proceed to finish and exit the installation program The software now is installed and can be started ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 1 5 Front Panel Control 1 5 1 Functions 1 5 2 Most of the functions of the system can be controlled via the local keyboard There are some exceptions Audio routing Separate Audiogain and level Separate Audio delay VBI Setup Special Timecode properties For these functions special setup configurations ar recalled which can be defined using the remote control software Key Properties There are three groups of keys with different properties e Toggle key directly modifies the parameter of a function e Shortcut key provides fast access of a ded
35. 000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 148 ASPECT 2000D User Manual 14 2 Cursor Preset 14 2 1 Recalling a Cursor default Setup Predefinition There two standard settings available Numbers given as Y pixel line field b Safe area Cursor 1 set to H V 35 7 Cursor 2 set to H V 684 236 c Title area Cursor 1 set to H V 70 12 Cursor 2 set to H V 649 231 Via Menu Press Menu Turn the rotary knob until the cursor points to cursor Press Select Turn the rotary knob until the cursor points to predef Press Select Select the desired setting by turning the rotary knob e Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 Select the desired predefinition ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 149 14 2 2 Recalling a local Cursor Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to cursor 3 Press Select 4 Turn the rotary knob until the cursor points to preset 5 Press Select 6 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 R
36. 3 Noise Reduction Linear Filters cccccseee 89 11 3 1 Recursive Noise Reduction Filter 0 89 11 4 Noise Reduction Nonlinear Filter 0 91 11 4 1 Median Filter Factor A eeeceeeeeeeeeeeeeeeeeeeeeeeee 91 11 4 2 Median Filter Factor B n se 92 99 5 Filter PreS tscied ocdszececexetedsecteecoescsdtecdeezceectsnacnecesdeaecss 93 11 5 1 Recalling a Filter default Setup Predefinition 93 11 5 2 Recalling a local Filter Preset 94 11 5 3 Saving a local Filter Preset ee eee 95 Color Correction 2 2 cccceeeeeeeeeeeeeeeeeeeees 96 41 6 INtrOGUCTION lt 0 c scce cee edicececceceecedenccteceseseesccccecengecccice 96 11 6 1 Color Correction Enable cceeeeeeeeees 97 11 6 2 Color Correction pre white level 00 98 11 6 3 Color Correction pre black level ccccee 99 11 6 4 Color Correction gamma cceeeeeeeeeees 100 11 6 5 Color Correction post white level 0 101 11 6 6 Color Correction post black level 0 102 11 6 7 Color Correction display cccceeeeeeeees 103 11 7 Preset Color Correction 2 cs ccceeeeeeeeeeeeeees 104 11 7 1 Recalling a color correction default Setup Pr definition Ji iisas in 104 11 7 2 Recalling a local color correction Preset 105 11 7 3 Saving a local color correction Preset 106 12 hegalizer ii iiscstscte
37. 8 select ON or OFF by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Audio Processing 2 click off or 32kHz or 48kHz in the DV field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 120 ASPECT 2000D User Manual 13 2 6 DV Audio Input channel select The DV format allows the processing of two audio channel pairs for the sample rate 32kHz The ASPECT 2000D supports one input channel pair so occasionally it has to be selected which chan nel pair shall be processed Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Processing Press Select Turn the rotary knob until the cursor points to Channel Press Select turn the rotary knob to select channel 1 2 or 3 4 ONOOPON gt Via Shortcut n a Via Remote Control Software 1 Open the window Audio Processing 2 select channel 1 2 or 3 4 on the DV tab ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 121 13 3 Preset Audio Input 13 3 1 Recalling a Audio Gain default Setup Predefinition The default audio gain setup forces the gain of all channels to OdB Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Processing Press Select Turn the rotary knob until the cursor point
38. ASPECT 2000D User Manual 13 2 4 Audio Input XLR select analog AES The system supports analog and digital external audio which can be embedded into the output SDI data stream The input has to be set to one of these two formats This setting is not necessary on the AES analog output both formats are provided in parallel Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Processing Press Select Turn the rotary knob until the cursor points to EXT IN Press Select Turn the rotary knob to select between analoge and AES ON D O R WN gt Via Shortcut n a Via Remote Control Software 1 Open the window Audio Processing 2 click analog or AES in the XLR field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 119 13 2 5 DV Audio Resampling Input The Firewire input supports the audio sample rates 32kHz 44 1kHz and 48kHz To connect to the studio world it is necessary to convert to 48kHz on the system output For the most common sample rates 32kHz and 48kHz the system contains a resample filter fort he conversion Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Audio 3 Press Select 4 Turn the rotary knob until the cursor points to Processing 5 Press Select 6 Turn the rotary knob until the cursor points to Resample 7 Press Select
39. ASPECT 2000D User Manual ASPECT 2000D USER MANUAL Document UMASPECT2000D 001 Rev ASPECT2000D 001 Table of Contents 1 Introduction 0 este eee cence ee eeeeeeeeeeeeeeeeees 4 1 1 Extent of Delivery ce cceeeeeeeceeeeeeeeeeeeeeeeeeeees 4 1 2 CONMOCUOMS voias annin iadaa irodai panhia anaia iiaa 5 1 3 POWGM sisse cscs sc cetecaddsicsceccit acces scececteetesduncdecasssedeenascxeceie 7 1 4 Remote Control Software 2 c cceeeeeeeeeeeeees 8 1 4 1 System Requirements cecesseeeteeeeeees 8 14 2 Instalati n 4 20 siete cscssceetenzetedastdeceeeavidsabedaeteesececee 8 1 5 Front Panel Control 2 cceseeeeeeeeeeeeeeeeeeeeeeeeeees 9 TOT FUNCIONS aa ete eanel Heese 9 1 5 2 Key Properties cccccssseceeeeeesssecceeeeeeesenenes 9 1 5 3 Menu Properties ssssssssssssssreeeeeeeeees 11 1 6 Using the Remote Control Software 12 1 6 1 Device Registration on the PC e 12 1 6 2 Device selection on the PC ccceeeeeee 13 2 Housekeeping Functions 0 00 14 2A INtrODUCTION eacccecescssshcced secs ccecenceet dese sriain eisses 14 2 1 1 Keyboard button lights 0 eeeeeeeeeeeees 14 2 1 2 Keyboard display contrast ccceeeeeeeeeees 14 3 Video Input 2 ceeeeeeeeeeeeeeeeeeeeeeeeeeeee 15 3 1 Input Source and Standard Selection 15 3 1 1 INpUt SOUFCE
40. ASPECT2000D 001 74 ASPECT 2000D User Manual 9 5 2 Recalling a local Aspect amp Zoom Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to ARC 3 Press Select 4 Turn the rotary knob until the cursor points to preset 5 Press Select 6 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 75 9 5 3 Saving a local Aspect amp Zoom Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select SOD Or PN gt Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 76 ASPECT 2000D User Manual 10 WSS VI Wide Screen Signaling Video Indexing 10 1 Introduction The Aspect 2000D supports line 23 WSS wide screen signalling and VI video indexing
41. D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 83 10 2 3 Saving a local WSS VI Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to WSS VI Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NDRRON Via Shortcut n a Via Remote Control Software 1 Open the window Wide Screen Signalling WSS amp Video Indexing VI 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 84 ASPECT 2000D User Manual 11 Video Signal Processing 11 1 General Functions OPERATION oe ee Names est one mw C mE DE o DES Vertical Vertical Cormg Cormg Fi YC O OO 4 ne o old MEDIAN FACTOR A FACIORE v c 2D _J 2p MEE 3D _J 3D mij SD TAP TAE _ DEEN _ E L 1 mii mj 2 z2 uf 3 F E pr 4 rie al ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 85 11 1 1 Filter enable Using this function allows a direct A B comparison of the impact a dedicated overall filter setting has to the video signal OFF all filters are switched off bypass ON filters active Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to VidProc 3 Pre
42. ECT 2000D User Manual 11 2 2 Coring Enhancement The coring threshold affects both the horizontal and vertical enhancement filter Via Menu 1 2 3 4 5 6 7 8 9 1 Press Menu Turn the rotary knob until the cursor points to VidProc Press Select Turn the rotary knob until the cursor points to Enhance Press Select Turn the rotary knob to Y luminance or C chrominance or Y C both components Press Select Turn the rotary knob until the cursor points to Coring Press Select 0 adjust Coring to the desired level using the rotary knob Via Shortcut n a Via Remote Control Software PONS Open the window Video Signal Processing Select Y C separate adjustment of luminance chrominance or Y C adjust Coring to the desired for value the horizontal and vertical direction when switching between Y C and Y C the systems keeps the different settings ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 89 11 3 Noise Reduction Linear Filters The system provides two linear noise reduction algorithms Recursive Noise reduction Linear recursive algorithms dedicated to statistic noise characteristics camera noise Transversal Filter Linear nonrecursive algorithm dedicated to high frequency noise The algorithms can be setup separately for luminance and chrominance if necessary 11 3 1 Recursive Noise Reduction Filter The application of recursive frame ba
43. ECT 2000D User Manual 15 3 3 Timecode inserter manual VITC line select Select the lines for VITC insertion There is an identical menu in the VBI menu The setting can be done via both menues in the same manner Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to inserter 5 Press Select 6 Turn the rotary knob until the cursor points to VITC 7 Press Select 8 Turn the rotary knob until the cursor points to OUTPOS 9 Press Select 10 select the desired lines Via Shortcut 1 Press Timecode 2 Turn the rotary knob until the cursor points to reader 3 Press Select 4 Turn the rotary knob until the cursor points to VITC 5 Press Select 6 Turn the rotary knob until the cursor points to OUTPOS 7 Press Select 8 select the desired lines Via Remote Control Software 1 Open the window Timecode 2 activate the extended window 3 select the desired lines in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 161 15 3 4 Timecode inserter RP196 activate Enable of the RP196 insertion into the outgoing video signals Via Menu SOON aAPWN gt lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until th
44. IS OMS n eie aeaa aeren ainin 141 Introductio sinini adaa 14 1 1 Cursor enable cccccccccecseeeeeesssseeeeeeeeeseee 14 1 2 Cursor position display 14 1 3 Cursor position horizontal left 143 14 1 4 Cursor position horizontal right 144 14 1 5 Cursor position vertical top cccceeeeee 145 14 1 6 Cursor position vertical bottom 008 146 14 1 7 Cursor Mode cccccccccccessseceeeeeessteeeeeeeeseaee 147 14 2 Cursor Preset ccciscesetcccesceesscccedecensntecereseseseevenees 148 14 2 1 Recalling a Cursor default Setup Predefinition 148 14 2 2 Recalling a local Cursor Preset 149 14 2 3 Saving a local cursor Preset ceee 150 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 3 15 Timecode wc c0e cnn senna 151 15 1 Introduction cccccceceeeeeeceseeceeeeceeeesseeeeeeeeseeeeeees 151 15 2 Timecode Reader sssscceeeeeseeesssseeeeeeseeeeeeees 152 15 2 1 Timecode Reader Source select 6 154 15 2 2 Timecode Reader VITC line select auto 155 15 2 3 Timecode Reader manual VITC line select 156 15 2 4 Keyboard setting of the reader dropframe MOG i cos23 ios ots aa e andaa idee 157 15 3 Timecode Inserter 158 15 3 1 Timecode inserter MASTER activate 158 15 3 2 Timecode inserter VITC activate 159 15 3 3 Timecode inserter manual VITC line selec
45. Menu ONOOPON gt Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to dropframe Press Select set ON or OFF by turning the rotary knob Via Shortcut DOE ON Press timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to dropframe Press Select set ON or OFF by turning the rotary knob ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 158 ASPECT 2000D User Manual 15 3 Timecode Inserter The timecode inserter adds the information prduced by the timecode generator into the output video stream The system supports the following formats VITC only available on the SDI video output RP196 only available on the SDI video output RP188 only available on the SDI video output DV TC only available on the DV Firewire video output The LTC timcode is always available 15 3 1 Timecode inserter MASTER activate General enable of TC insertion into the outgoing video signals Via Menu Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to MASTER EN Press Select select On or Off via the rotary knob ONDA WN gt lt 5 Shor
46. Open the window Color Correction 2 click on the upper right symbol in the window Preblacklevel 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 100 ASPECT 2000D User Manual 11 6 4 Color Correction gamma The settings can be made independantly for each color or alternatively for all three colors in the same man ner The Remote Control Software gives a better overview so this first step is not necessary Gamma from 0 5 to 1 5 is supported Via Menu Turn the rotary knob until the cursor points to Color Press Select Turn the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to gamma and the desired color all red green blue Press Select turn the rotary knob to adjust to the desired value NOORWN gt Via Shortcut n a Via Remote Control Software 1 Open the window Color Correction 2 click on the upper right symbol in the window gamma 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 101 11 6 5 Color Correction post white level The settings can be made independantly for each color or alternatively for all three colors in the same man ner The Remote Control Software gives a better overview so this first step is not necessary Via Menu Turn the rotary knob until the cursor points to Color Press Select Turn
47. POSITION vie avro E LTC 7 07 320 RP196 RP Iss f Dve a OF ai AUTO VITC The VITC is transmitted in the VBI of the incoming video signal It should conform to SMPTE 12M The reader either automatically detects the presence of a VITC signal in the available a rea or can be set manually to decode a dedicated line If in automatic mode more than one line carry valid data the first line will be processed The remote control software indicates the VBI lines which show valid VITC as black and the processed line in green RP188 The RP188 format is described by SMPTE RP 188 and ITU BT 1366 It is a digital format which is available only on the SDI input The active line is always detected automatically RP196 The RP196 format is another digital representation of timecode described by SMPTE RP 196 It is a digital format which is available only on the SDI input The active line is always de tected automatically LTC The LTC is a common analog format which is not part of the video signal It is described in SMPTE 12M DV TC DV TC is a special fromat only available with the DV Firewire input All mentioned formats support dropframe for 59 94 Hz input signals Normally the input should be set to au tomatic dropframe detection but under special conditions it can be useful to force the format manually The remote control software displays the decoded timecode in the reader timecode window Please note The displayed tim
48. T 2000D User Manual 167 15 4 Timecode Generator 15 4 1 Introduction The timecode generator is highly configurable for different applications It provides some common and easy to use basic operation modes and additionally an expert mode which allows the definition of complex procedures and trigger events w TIMECODE x Input timecode Switch to normal mode 00 01 06 16 Mode Jam Syne EE Qutput timecode P Processing gy P foo 01 06 13 gt User value C Input oo 00 00 05 P E Flywheel INPUT The Input mode passes the incoming timecode directly to the output without any processing This main tains the 1 1 relationship picture to timecode But the user should be aware that it may produce a non continous flow when the system acts as a frame store synchronizer Drop frame timecode may be disturbed too FLYWHEEL The generator runs free and delivers an independent nondisturbed timecode which conforms to the standards It can be manually set to define the start value JAM SYNC Thegenerator tries to deliver a nondisturbed time code which follows the input with a minimum di stance Small gaps dropouts at the input will be masked because the generator is able to run free for a limited number of frames If the input timecode fails and starts again or if it skips the generator will be restarted with a new value which lies as near as possible to the input value This guarantees that the timecode on the output is al
49. a Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to reader 5 Press Select 6 Turn the rotary knob until the cursor points to source 7 Press Select 8 select the desired source via the rotary knob Via Shortcut 1 Press Timecode 2 Turn the rotary knob until the cursor points to reader 3 Press Select 4 Turn the rotary knob until the cursor points to source 5 Press Select 6 select the desired source via the rotary knob Via Remote Control Software 1 Open the window Timecode 2 activate the extended window 3 select the desired Source in the reader section ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 155 15 2 2 Timecode Reader VITC line select auto Via Menu SERMON AARON gt lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to autosel Press Select select auto or manual via the rotary knob Shortcut ONOONPWN gt Via Press Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points
50. a and associated con trol information into the ancillary data space of serial digital video conforming to ANSI SMPTE 259M The standard provides a minimum of two audio channels and a maximum of 16 audio channels based on the available ancillary data in a given format four channels maximum for composite digi tal CHANNEL 1 The professional interface format for digital audio is speci GROUP 1 CHANNEL 2 fied in the AES document AES3 1992 This is often re CHANNEL 3 ferred to as AES3 It is a serial data format carrying two CHANNEL 4 channels of audio which can be left and right sum and CHANNEL 1 difference or two independent mono signals The data for GROUP 2 CHANNEL 2 bt CHANNEL 3 mat has provision for up to twenty four bits per sample with CHANNEL 4 sampling frequencies of 32 kHz 44 1 kHz and 48 kHz CHANNEL 1 l l l GROUP 3 CHANNEL 2 AES EBU carries two channels typically a stereo signal CHANNEL 3 left and right Audio data is embedded in a group format CHANNEL 4 A group is defined as two AES EBU signals or four monau CHANNEL 1 ral channels In the 4 2 2 format there is room for 4 groups GROUP 4 ENE of AES EBU channels or 16 channels of monaural audio in CHANNEL 4 the SDI signal ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 114 ASPECT 2000D User Manual The processing of audio information within the ASPECT 2000D is completely independant of the han dling of video signals The aud
51. ain Y Press Select Adjust by turning the rotary knob Via Shortcut 1 Press Y Gain 2 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Gain Y to the desired level ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 4 1 2 Input Chroma Gain Gain C Adjustment of the chrominance input gain Controls both Cb and Cr components simultaniously Range 0 000 1 999 Available for all sources Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to Gain C Press Select Adjust by turning the rotary knob OY OTP COIN Via Shortcut 1 Press C Gain 2 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Gain C to the desired level PAL vector display of color bars NTSC SMPTE color bar test picture The dots are in the approprate boxes and the color burst placed on the horizontal axis ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 24 ASPECT 2000D User Manual 4 1 3 Input Chroma Balance C C Adjustment of the Cb Cr balance Controls both Cb and Cr components simultaniously Range 0 000 1 999 Available for all sources Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the
52. ame to each of the global presets which ap pears also on the display of the local keyboard So it is easy to recover a special system setup Of course the current system setup as well as the content of all preset memorys are saved when power is switched off Further the Remote Control Software allows to backup the content of the complete set of preset mem ory into an MS Excel file This enables the user to store an indefinte number of system settings which can be edited restored to the system or archived with a finished job The functions Bypass Freeze and Testpattern are not included into the preset system and will be reset when the system is switched off ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 181 16 2 Preset Operation 16 2 1 Storing of a global Preset Via Menu ONAARWN gt Press Menu Turn the rotary knob until the cursor points to Preset Press Select Turn the rotary knob until the cursor points to Save Preset Press Select Turn the rotary knob until the cursor points to the desired position Press Select the current global status of the system will be saved Via Shortcut Oahwon gt Press Preset Turn the rotary knob until the cursor points to Save Preset Press Select Turn the rotary knob until the cursor points to the desired position Press Select the current global status of the system will be saved Via Remote Control Software 1 2
53. antly for each color or alternatively for all three colors in the same man ner The Remote Control Software gives a better overview so this first step is not necessary Via Menu Turn the rotary knob until the cursor points to Color Press Select Turn the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to adj pre white and the desired color all red green blue Press Select turn the rotary knob to adjust to the desired value aon NO Via Shortcut n a Via Remote Control Software 1 Open the window Color Correction 2 click on the upper right symbol in the window Prewhitelevel 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 99 11 6 3 Color Correction pre black level The settings can be made independantly for each color or alternatively for all three colors in the same man ner The Remote Control Software gives a better overview so this first step is not necessary Via Menu Turn the rotary knob until the cursor points to Color Press Select Turn the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to adj pre black and the desired color all red green blue Press Select turn the rotary knob to adjust to the desired value Cr ONS aO Via Shortcut n a Via Remote Control Software 1
54. by turning the rotary knob Qnarwn gt Via Shortcut n a Via Remote Control Software 1 Open the window Legalizer 2 Select ON or OFF in the operation field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 108 ASPECT 2000D User Manual 12 1 2 Legalizer upper limit The standard maximum value is 940 Via Menu Turn the rotary knob until the cursor points to Legalizer Press Select Turn the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to upper all upper R upper G upper B Press Select turn the rotary knob to adjust to the desired value NOahons Via Shortcut n a Via Remote Control Software 1 Open the window legalizer 2 click on the upper right symbol in the window upperlegalizer 3 adjust the desired parameter ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 109 12 1 3 Legalizer lower limit The standard minimum value is 64 Via Menu Turn the rotary knob until the cursor points to Legalizer Press Select Turn the rotary knob until the cursor points to adjust Press Select Turn the rotary knob until the cursor points to lower all lower R lower G lower B Press Select turn the rotary knob to adjust to the desired value NOaPwns Via Shortcut n a Via Remote Control Software 1 Open the window legalizer 2 click on the upper right symbol
55. c Amp Preset 2 33 4 2 3 Saving a local Proc Amp Preset 05 34 5 Video Output 0 c ccceecccesceseeessenscnnneecceceeeess 35 5 1 System Output SettingS 2 ceeeeeeeeeeeeeee 35 5 1 1 Output Standard Selection ccccceeeeeeee 36 5 1 2 Output Bypass ccccccceceeeeeeeeeeeeeeseteeeeeeeees 5 1 3 Freeze 5 1 4 Output DV Format 5 2 Output Preset cccccceesssseseeeeeeessseeeeeeeeeees 5 2 1 Recalling a local Output Preset 5 2 2 Saving a local Output Preset 00 ceee 6 System Synchronisation 00000 0 41 6 1 Introduction 20 00cccceestececccensetcececeeeseneceeedeetenececentetene 41 6 2 Genlock Operation s ssssssnsnensennnen ennn nnne nenne nenna nanne 42 6 2 1 Genlock Activate 0 0 cccccccceeeeeneeeseteeeteeeees 42 6 2 2 Genlock H Delay c ccccccceeeeeeeseteeeeeeeeees 43 6 2 3 Genlock Termination c cccceeeeeeteeeeeeteees 44 6 3 Genlock Preset 22 2 cc ccceeeceeeeeceeeeneeneeeceeeenees 45 6 3 1 Recalling a local Genlock Preset 0 45 6 3 2 Saving a local Genlock Preset cee 46 7 Test Pattern cccccccssssecssssccesseeeseesseeeees 47 T A Test Pattern os ccsicc cies feccdesicccccte ce decccctecenscetereeccscceteeee 47 7 1 1 Test Pattern activation eee eee 47 7 1 2 Test Pattern Selection 0 ceceeereeeeees 48 8 VBI Processing cceeeeeeee
56. caused by a variety of prob lems in the signal s history including cross luminance and cross color effects Use of low pass spa tial filtering is not desirable as the problems are reduced at the cost of resolution As with other features to preserve the integrity of the input signal these facilities should only be used to correct for problems picture correlated noise soft input picture and should only be used to a minimum level to generate the required improvement Over use of the positive values of enhancement can generate ringing white lines around objects Use of the negative values will reduce bandwidth it is a variable low pass filter and should only be used when stationary noise components are visible In certain system situations e g output to a system with a limited bandwidth it may be useful to use this feature specifically to eliminate informa tion that is likely to cause problems in the subsequent process pre processing for some compres sion systems for example In general it is normally acceptable to leave some horizontal and vertical enhancement active level 2 3 which will give a good sharp picture from most material without ringing problems This is par ticularly useful for composite inputs where a boost in resolution is often beneficial The enhancement function improves the high frequency response of the system if positive parame ters are selected This bears the risk that also high frequency noise will be amp
57. cece ccc ccecteeeeeeeesseeeeeesessneeees 16 3 1 2 Automatic Input Standard Selection 17 3 1 3 Manual Input Standard Selection 0 18 3 2 Various Input Setup Features ceeeeee 19 3 2 1 Input Black White 00 ccceeeeeeeeeeeeeteeeees 19 3 3 Preset Input Source and Standard Selection 20 3 3 1 Recalling a local input Preset 20 3 3 2 Saving a local input Preset c eee 21 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 4 Input Video Proc Amp eeeee 22 4 1 Input Proc AMDP ccccceeceeeceeeeeeeeeeeeeeeeeeeeneeeteeeeseeees 22 4 1 1 Input Luminance Gain Gain Y 00 22 4 1 2 Input Chroma Gain Gain eee 23 4 1 3 Input Chroma Balance C C cc cccccceesseeeeees 24 4 1 4 Input Black Level pedestal 4 1 5 Input Offset Cp cccccssseccesssssseseeesssssseeeeeees 4 1 6 Input Offset Cy ccccccssecceeesssseeeeeesssssseeeeeees 4 1 7 Input horizontal Position cc ceeeeeeeceeeeeeeeeees 4 1 8 Input horizontal Chroma Position 00 29 4 1 9 Input vertical Position cc cececeeesssteeeeeeeeeeeees 30 4 1 10 Input vertical Chroma Position cccccce 31 4 2 Preset Proc AMP wiv tecssciovcvsicncvictsrcincicdas 32 4 2 1 Recalling a Proc Amp default Setup Predefinition cccccccceeceeeeeeeeeeeeeeeeeeeeeees 32 4 2 2 Recalling a local Pro
58. cessing 1 2 2 Select ON or OFF for mute ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 116 ASPECT 2000D User Manual 13 2 2 Audio Input Master Level The master level function applies to all input channels simultaneously Range 6dB Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Processing Press Select Turn the rotary knob until the cursor points to Master Press Select adjust the level by turning the rotary knob ONAARWON gt Via Shortcut 1 Press Audio Level 2 adjust the level by turning the rotary knob Via Remote Control Software 1 Open the window Audio Processing 1 2 2 adjust the level using the MAIN slider ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 117 13 2 3 Audio Input Gain amp Level The Gain and Level functions allow the adjustment for single audio channels independantly They are available only within Remote Control Software and act like a standard mixer Via Menu n a Via Shortcut n a Via Remote Control Software 1 Open the window Audio Processing 1 2 2 The rotary knobs in the upper part of the mixer act as gain controller The level adjustment is done via the sliders as usual The numbers refer to the input channel ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 118
59. d Deembedding of SDI input channel 13 16 audiogruop 4 e Routing of external XLR input channel 1 4 to XLR output channel 1 4 Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to audio 3 Press Select 4 Turn the rotary knob until the cursor points to output 5 Press Select 6 Turn the rotary knob until the cursor points to EXT 7 Press Select 8 Select the desired configuration by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window audio output 2 Select the tab XLR 3 Select the desired configuration in the Predefinition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 138 ASPECT 2000D User Manual 13 7 3 Recalling an Audio DV Output default Setup Predefinition The DV Firewire output supports 2 audio channels which can be selected out of the 16 SDI input channels and the 4 external channels There are 10 predefined setup configurations available SDI input channel 1 2 SDI input channel 3 4 SDI input channel 5 6 SDI input channel 7 8 SDI input channel 9 10 SDI input channel 11 12 SDI input channel 13 14 SDI input channel 15 16 External input channel 1 2 External input channel 3 4 lt Vo sa ztoaqnctya wre wr reer eS Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to output Press Select Turn the rotary
60. dard ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 3 2 Various Input Setup Features Some inputs accasionally net additional setup This chapter contains the supported features 3 2 1 Input Black White 19 Disables input colour information Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Input 3 Press Select 4 Turn the rotary knob until the cursor points to B W 5 Press Select 6 Select color or B W Via Shortcut n a Via Remote Control Software 1 Open the window Input 2 click B W or Color in the option field The B W status will be marked red as a warning ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 20 ASPECT 2000D User Manual 3 3 Preset Input Source and Standard Selection 3 3 1 Recalling a local input Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Input 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Input 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 3 3 2 Saving a local input Pres
61. delASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 63 9 3 Crop 9 3 1 Input Cropping Top Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to ARC 3 Press Select 4 Turn the rotary knob until the cursor points to Crop 5 Press Select 6 Turn the rotary knob until the cursor points to In Upper 7 Press Select 8 Adjust the Cropping using the rotary knob Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to In Upper 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the cropping by the appropriate slider besides the input window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 64 ASPECT 2000D User Manual 9 3 2 Input Cropping bottom Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to In Lower Press Select Adjust the Cropping using the rotary knob ONAAP ON Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to In Lower 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the cropping by the appropriate slider besi
62. des the input window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 65 9 3 3 Input Cropping right Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to In Right Press Select Adjust the Cropping using the rotary knob ONOARWN gt Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to In Right 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the cropping by the appropriate slider besides the input window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 66 ASPECT 2000D User Manual 9 3 4 Input Cropping left Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to In Left Press Select Adjust the Cropping using the rotary knob ONAAP ON Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to In Left 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the cropping by the appropriate
63. e n a ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 187 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 188 ASPECT 2000D User Manual ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 17 189 P XForm Systems GmbH Spechtweg 1 D 38108 Braunschweig Telephone 49 531 302928 91 Facsimile 49 531 302928 99 E Mail info xformsystems de Internet www xformsystems de ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001
64. e cursor points to RP196 Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Shortcut ONONPWN gt Via Press Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to RP196 Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Remote Control Software 1 2 3 Open the window Timecode activate the extended window select On or Off in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 162 ASPECT 2000D User Manual 15 3 5 Timecode inserter manual RP196 line select Select the line for RP196 insertion Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to inserter 5 Press Select 6 Turn the rotary knob until the cursor points to RP196 7 Press Select 8 Turn the rotary knob until the cursor points to OUTPOS 9 Press Select 10 select the desired line Via Shortcut 1 Press Timecode 2 Turn the rotary knob until the cursor points to reader 3 Press Select 4 Turn the rotary knob until the cursor points to RP196 5 Press Select 6 Turn the rotary knob until the cursor points to OUTPOS 7 Press Select 8 select the desired line Via Remote Control S
65. e rotary knob until the cursor points to gen pos H 5 Press Select 6 set the desired horizontal position of the generator display by the rotary knob Via Remote Control Software 1 Open the window timecode 2 select the desired display position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 177 15 5 6 Timecode generator vertical display position Via Menu ONONRWN gt lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to display Press Select Turn the rotary knob until the cursor points to gen pos V Press Select set the desired vertical position of the generator display by the rotary knob Shortcut OOTP O Via Press timecode Turn the rotary knob until the cursor points to display Press Select Turn the rotary knob until the cursor points to gen pos V Press Select set the desired vertical position of the generator display by the rotary knob Remote Control Software 1 2 Open the window timecode select the desired display position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 178 ASPECT 2000D User Manual 15 6 Timecode Preset 15 6 1 Recalling a local timecode Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob unti
66. e window Output 2 Select DVCAM or DVCPRO ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 5 2 Output Preset 39 5 2 1 Recalling a local Output Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Output 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Output 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 40 ASPECT 2000D User Manual 5 2 2 Saving a local Output Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NOaPRwns Via Shortcut n a Via Remote Control Software 1 Open the window Output 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 6 System Synchronisation 6 1 Introduction 41 When various video sources are combined their signals should be ti
67. ecode may appear discontinous This usually is the case if the computer or the network slows down due to heavy load ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 153 ASPECT 2000D User Manual Fle Sle es Pace P Aindi00 ETETE Hp E a a C Q z x AIOdNI fl indy NOILSOd A T4510 TI WS IL IndIN0 I JLINANI O Oo AV ISIC J ILINdINO INANI _ AY TSI HIJAS NO oze zo aw OVW Yas omy g aa O aan ERGEECRE GY fa 2A a ozelo LA oO omy sua HOILUSOd JIA aos asned pels azeu api ap o33aW je saso E ana EESAN rvoad JOIS JILI Y 0000 00 00 0000 00 00 aposawn nding E A Y HOMLICNOS dois AGO DAWIL JO UOlesul spodaluy o NOIMIGNOD IAY 15 avis Tiosda 00 00 00 00 q A eor aneres ynduy j 3 on ourlg wef e PART AW HIdOIT apopy 4 00 00 00 00 aposauy ndu AOL IANIS ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 154 ASPECT 2000D User Manual 15 2 1 Timecode Reader Source select The source select works context sensitive because dependant of the video input signal some timecode sources are not available LTC always selectable VITC only available for SDI video input RP196 only available for SDI video input RP188 only available for SDI video input DV TC only available for DV Firewire video input Vi
68. edefined setup configurations available for the SDI audio output a Routing matrix set to 1 1 all input channels are directly routed to the corresponding output chan nels No shuffling b Embedding of the 4 external XLR input channels into ouput channel 1 4 audio group 1 Re maining output channels taken from the corresponding inputs c Asb but embedding in output channel 5 8 audiogroup 2 d Asb but embedding in output channel 9 12 audiogroup 3 e Asb but embedding in output channel 13 16 audiogroup 4 Via Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to output Press Select Turn the rotary knob until the cursor points to SDI Press Select Select the desired configuration by turning the rotary knob ONDUEN Via Shortcut n a Via Remote Control Software 1 Open the window audio output 2 Select the tab SDI 3 Select the desired configuration in the Predefinition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 137 13 7 2 Recalling an Audio XLR Output deembedding default Setup Predefinition There are 5 predefined setup configurations available for the SDI audio output a Deembedding of SDI input channel 1 4 audiogruop 1 b Deembedding of SDI input channel 5 8 audiogruop 2 c Deembedding of SDI input channel 9 12 audiogruop 3
69. eeeeeees 49 8 1 VBI Processing Caption 22 eceeeeeeeeeee 49 8 1 1 VBI Test Signal Insertion 0 0 ceeeeeeeees 50 8 1 2 Timecode inserter manual VITC line select 51 822 VBI Preset coenen undanta eene aiaa erana 52 8 2 1 Recalling a local VBI Preset 52 8 2 2 Saving a local VBI Preset ceeeeeeees 53 9 Aspect Ratio Conversion ARC and ZOOM eee aes 54 O31 Introductionis eaaa iadan a aaa 54 9 1 1 ARC Input Control cceccccssceceeeesssseeeeeees 54 9 1 2 Manual selection of the input format 55 9 1 3 Selection of the output format eee 56 9 2 ZOOM Pan amp SCAN cccccsceeceessseeeceeesssseeeeeeeeesseaees 57 9 2 1 Manual adjustment of the output zoom factor 57 9 2 2 Manual adjustment of the output aspect ratio 58 9 2 3 Manual adjustment of the output horizontal ZOOM si a eaa s Eear aE E rN a 59 9 2 4 Manual adjustment of the output vertical zoom 60 9 2 5 Manual adjustment of Pan csceeeeees 9 2 6 Manual adjustment of Scan 9 3 1 Input Cropping Top ce 9 3 2 Input Cropping bottom 9 3 3 Input Cropping right 0 c ceeeeeeeeeeeeeeteeees 9 3 4 Input Cropping left eeeeeeeeeeeteeeeteeees 9 3 5 Output Cropping top c eee 9 3 6 Output Cropping bottom 9 3 7 Output Cropping right 9 3 8 Output Cropping left ce ec eeeeeeeeeeeeeeeees
70. eeeeeseeeeeeteeeeeaes 122 13 3 3 Recalling a local audio input processing Preset 13 3 4 Saving a local audio input processing Preset 124 13 4 Audio Delay iiie easa tesoura areia daai 125 13 4 1 Audio Auto Delay eeeeeeee 125 13 4 2 Audio Master Delay eee 126 13 4 3 Separate Audio channel Delay 005 127 13 5 Preset Audio Delay cccccsssesseessesseeesseeesneeees 128 13 5 1 Recalling a Audio Delay default Setup Pre definition 2tes 2 etna e tenella 13 5 2 Recalling a local audio delay Preset 13 5 3 Saving a local audio delay Preset 13 6 Audio OUtpUt eee ceeeeesseeceeeeeeseseeeeeneeeseeaeee 13 6 1 Operating the Audio Routing eee 13 6 2 Audio Embedder Sequence c ccececeees 13 6 3 Audio Control Packet 0 008 13 6 4 DV Audio Resampling Output 13 6 5 DV Audio Output channel select 13 7 Preset Audio OUtpUt cee ceeecceeeesssseeeseeeeeseeaees 13 7 1 Recalling an Audio SDI Output default Setup Predefinition ccccccecceeeeeceeeeeeeeeeesteeeeeaes 136 13 7 2 Recalling an Audio XLR Output deembedding default Setup Predefinition c ee 137 13 7 3 Recalling an Audio DV Output default Setup Predefinition c ccceseceeeeceeeeeseeeeseteeeeeaes 13 7 4 Recalling a local output Preset 13 7 5 Saving a local audio output Preset 140 14 CU
71. elASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 134 ASPECT 2000D User Manual 13 6 4 DV Audio Resampling Output Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Resample Press Select select ON or OFF by turning the rotary knob ONO OB ONS Via Shortcut n a Via Remote Control Software 1 Open the window Audio Output 2 select the DV tab 3 click off or 32kHz or 48kHz on the DV tab ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 135 13 6 5 DV Audio Output channel select The system supports one audio pair on the DV output Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Channel Press Select turn the rotary knob to select the desired channel pair ONO ONS Via Shortcut n a Via Remote Control Software 1 Open the window Audio output 2 select the DV tab 3 select the desired channel pair on the DV tab ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 136 ASPECT 2000D User Manual 13 7 Preset Audio Output 13 7 1 Recalling an Audio SDI Output default Setup Predefinition There are 5 pr
72. ent of the output vertical zoom Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Zoom V Press Select adjust the factor using the rotary knob O On e GO za Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 adjust the factor in the zoom setting field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 9 2 5 Manual adjustment of Pan 61 Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to ARC 3 Press Select 4 Turn the rotary knob until the cursor points to Pan 5 Press Select 6 Select the desired value using the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 adjust the parameter in the zoom setting field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 62 ASPECT 2000D User Manual 9 2 6 Manual adjustment of Scan Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Scan Press Select S elect the desired value using the rotary knob Oy OV CON Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 adjust the parameter in the zoom setting field Mo
73. esired Preset via the rotary knob Press Select OCONAARWN gt Via Shortcut n a Via Remote Control Software 1 Open the window audio output 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 141 14 Cursors 14 1 Introduction The ASPECT 2000D provides two cursors which can be inserted into the output signal 14 1 1 Cursor enable The two cursors can be set either to crosshair H V or separate horizontal H or vertical V Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Cursor 3 Press Select 4 Turn the rotary knob until the cursor points to State 5 Press Select 6 select configuration by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect Ratio Conversion amp Zoom 2 select configuration in the cursor settings field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 142 ASPECT 2000D User Manual 14 1 2 Cursor position display The position of the cursorlines can be shown via the readout The persistance is selectable Via Menu Press Menu Turn the rotary knob until the cursor points to Cursor Press Select Turn the rotary knob until the cursor points to Display Press Select select the parameter by turning the rotary knob DOT EOS Via Shortcut n a Via Remote Control Software 1 Open the window As
74. et 21 Up to 4 local prest configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to Input Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NDRRON Via Shortcut n a Via Remote Control Software 1 Open the window Input 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 22 4 Input Video Proc Amp 4 1 4 1 1 Input Proc Amp ASPECT 2000D User Manual Video signals undergo various types of distortion The level of luminance and or chrominance may change decoders sometimes produce incorrect timing etc For this reason the system provides a versatile input Proc Amp to correct various signal parameters OSETE D 1000S C Gam Ch Cr Bal D onal OFFSET 1 Bk Level 0 0 Cr Obtset Cb Olt set a lt 0 0 Input Luminance Gain Gain Y T PROC AMP IMINGs PRESET Sons ar Adjustment of the luminance input gain Range 0 000 1 999 Available for all sources Via Menu AakRwNns Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to G
75. eter value back to default Submenu keys Recursive Median Aspect Zoom Crop Timing Audio Delay Monitor select Monitor Level Genlock Preset These keys point to the related submenu It normally contains more than one function which can be operated via the keys Menu and Select and the rotary knob The red LED of these keys is used to indicate the following e Flashing indicates that the related menu is activated e Steady light indicates that one of the related functions has a nondefault parameter In this case normally the function modifies the related signal Pressing the key for about 2 seconds will set all parameter values of the related menu back to default ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 11 1 5 3 Menu Properties The main menu is operated via the keys Menu and Select and the rotary knob The key Menu activates deactivates the selected menu The system stores the last active position and recalls it when entering the menu again If you wish to go to the menu start please deactivate the menu and activate it again All menus are operated similar The cursor is moved by the rotary knob while the key Select recalls the menu item If the cursor is on 7 the key Select leads to the next level in the menu tree If the cursor points to a parameter it can be modified via the rotary knob To leave this status please press Select ModelASPECT2000D Document
76. ev ASPECT2000D 001 150 ASPECT 2000D User Manual 14 2 3 Saving a local cursor Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to cursor Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NOaPRwns Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 151 15 Timecode 15 1 Introduction The ASPECT 2000D provides a powerful subsystem to read generate insert and display timecode infor mation The following formats are supported on the input and output VITC SMPTE 12M LTC SMPTE 12M RP196 SMPTE RP 196 RP188 SMPTE RP 188 ITU BT1366 DV Firewire The timecode reader generator inserter and display can be configured independently To simplify the operation the timecode subsystem offers various common settings But by using the expert mode it allows the setup of sophisticated procedures ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 152 ASPECT 2000D User Manual 15 2 Timecode Reader The timecode reader gets its input signal either from the LTC input or via the selected video source EE SOURCE ff VITC
77. he rotary knob until the cursor points to Delay 3 Press Select 4 Adjust the delay using the rotary knob Via Remote Control Software 1 Open the window Audio Delay 2 Adjust the delay using the knob in the master delay field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 127 13 4 3 Separate Audio channel Delay Sometimes it is necessary to adjust the audio delay separately for dedicated channels This function is available only via Remote Control Software Via Menu n a Via Shortcut n a Via Remote Control Software 1 Open the window Audio Delay 2 Adjust the delay using the knobs in the fields SDI delay and XLR delay resp ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 128 ASPECT 2000D User Manual 13 5 Preset Audio Delay 13 5 1 Recalling a Audio Delay default Setup Predefinition The default audio delay setup forces the audio master delay to automatic mode and all single channel delay settings to zero Via Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to delay Press Select Turn the rotary knob until the cursor points to Predef Press Select Select default by turning the rotary knob CO Gn BON Via Shortcut n a Via Remote Control Software 1 Open the window audio delay 2 Select default in the Predefinition field Mode
78. icated function bypassing the menu structure e Submenu key provides fast access of a submenu Toggle keys DV SDI Black also acts as shortcut key for testpattern menu Bars also acts as shortcut key for testpattern menu Bars Freeze Disable Audio Mute Monitor Mute Bypass When pressed these keys directly change the status of the related function The red LED inside the key indicates whether the related function is active or not The keys which cover the source selection have a special behaviour Pressing one of these keys se lects the desired input and activates the related context menu Flashing of the LED further indicates loss of signal on the input Reason could be either loss of signal a wrong input standard etc If this occurs please also check the status of the automatic standard selec tion ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 10 ASPECT 2000D User Manual Shortcut keys STD Standard Blacklevel V Gain C Gain C Bal Audio level Monitor level These keys point directly to a menu function and allow parameter modification via the rotary knob The red LED of the key is used to signal two different events e Flashing indicates that the parameter can be modified via the rotary knob e Steady light indicates that the parameter is modified to nonstandard In this case normally the function modifies the related signal Pressing the key for about 2 seconds will set the param
79. ight TIODI el a Power Main Power Plug Figure 1 3 1 Figure 1 3 2 1 Connect the power cable to the unit 2 Press the Power switch to turn the unit ON All control lights will illuminate until the system ends its boot procedure During this the following message appears on the display booting system please wait If no button lights up after the start period check the LED Bright seting in the panel menu The ad justment must be greater than zero in order to illuminate the lights ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 1 4 Remote Control Software The ASPECT 2000D package may contain software to control the unit via a PC Using the software has some essential advantages versus operating the unit via the local control panel 1 the complete range of functions is supported 2 in many situations the software does it far more clearly and self explaining If it is necessary to connect the systems to a network special RS232 to Ethernet Converters are pro vided as an option 1 4 1 System Requirements To use the software the PC should fulfill the following requirements e Prozessor speed greater than 1GHz e 512MB Ram e Microsoft Windows 2000 XP 2003 Vista e Atleast 10MB disc capacity e Screen resolution 1024 x 768 or better 65 535 colours or better 1 4 2 Installation To install the Remote Control Software please proceed as follows e Insert the CD into
80. insertion off timecode at the system output switched off This can make shure that any external machines do not act in an unexpected manner e Start value the generator starts with a user defined value e Last valid timecode the generator proceeds with the last valid timecode This allows an interruption of the workflow but nevertheless a continuous timecode will be recorded START CONDITION Please refer to the light green subwindow The selected condition is transfered to the generator by pressing the start button A trigger event is defined which starts the generator with the parameter setup with before start The following conditions are available e manual The generator manually starts with a click on the start button e when input becomes valid The generator waits until the reader detects a valid timecode on the input If the input is valid du ring the setup procedure the generator starts immediately e first time imput matches The generator waits until the input timecode is equal or larger as the trigger value Any further match will have no effect e any time imput matches like first time imput matches but on every match ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 169 STOP CONDITION Please refer to the dark green and the orange subwindow The selected condition is transfered to the generator by pressing the stop button A trigger event is defined which stops the gene
81. io is separated from the video signal at the input of the system passes the processing chain and is added to the video at the system output The processing is done according to 13 1 1 2 3 4 5 Decoding Demultiplexing Processing routing Delay Encoding Multiplexing 13 1 The audio processing is mainly based on a powerfull routing matrix which connects the signal from dif ferent sources destinations as SDI Firewire and the embedding deembedding of 4 analog AES SPDIF channels It supports 22 input channels and 22 channels on the output The system has an integrated delay unit which primarily is used to maintain the lip sync on the output It further provides adjustable delay up to 1sec for all 22 output channels imdependently It can be set to a shorter delay than the video processing so even negative delay adjustment is possible ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 115 13 2 Audio Input 13 2 1 Input Mute Via Menu Press Menu Turn the rotary knob until the cursor points to Audio Press Select Turn the rotary knob until the cursor points to Processing Press Select Turn the rotary knob until the cursor points to mute Press Select Select ON or OFF Co N OY Gi BON Via Shortcut 1 Press Mute in the audio field The key acts as toggle key Via Remote Control Software 1 Open the window Audio Pro
82. king Bars or Black or various ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 8 VBI Processing 8 1 VBI Processing Caption The vertical blanking interval is transparent to the incoming video signal The system is equipped to insert standard test signals into the vertical blanking interval It further allows the inserting of VITC timecode information Vv FIRST FIELD RECALL SAVE WORK v USER vl PRE DEFINITIONS BLANKED v Line 12 poems from input ColB ar50 SMPTE ColBar SMPTE Chroma Line 20 SMPTE Black Se Line 21 blanked v Line 22 blanked zij x SECOND FIELD Line 320 blanked v Line 321 blanked Line 322 blanked v Line 323 blanked Line 324 blanked Line 325 blanked Line 326 blanked ba Line 327 blanked v Line 328 blanked Line 329 blanked v Line 330 blanked Line 331 blanked v d Line 332 blanked v Line 333 blanked Line 3341 blanked v Line 335 blanked gt r lt E lt U E a E E a a a G eee 4 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 50 8 1 1 VBI Test Signal Insertion ASPECT 2000D User Manual The following test patterns are provided Black Color Bars different for 50 60Hz IWQ Bar 60Hz Red 2T ITU Multiburst ITU 2T20T ITU Line 330 50Hz ITU Line 331 50Hz ITU Line 17 Field 1 60Hz ITU Line 17 Field 2 60Hz C Ra
83. l the cursor points to Offset C Press Select Adjust by turning the rotary knob aA kRwWN gt Via Shortcut n a Via Remote Control Software 1 Open the window Proc Amp 2 adjust Offset C to the desired value ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 4 1 6 Input Offset C 27 Adjustment of the input chrominance offset Cb Range 11 4 11 4 in steps of 1 Available for all sources Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Procamp 3 Press Select 4 Turn the rotary knob until the cursor points to Offset C 5 Press Select 6 Adjust by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Proc Amp 2 adjust Offset Cr to the desired value ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 28 ASPECT 2000D User Manual 4 1 7 Input horizontal Position Adjustment of the horizontal input timing luminance chrominance Range 2370ns 2296ns in steps of 74ns 1 luminance pixel Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to Timing Press Select Turn the rotary knob until the cursor points to Y C Press Select Turn the rotary knob until the cursor points to Pos H Press Select 0 Adjust by turning the rotary knob SO ONO OURO os Via Shortcut
84. l the cursor points to cursor 3 Press Select 4 Turn the rotary knob until the cursor points to preset 5 Press Select 6 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 179 15 6 2 Saving a local timecode Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to cursor Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NDRRON Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 180 ASPECT 2000D User Manual 16 Presets 16 1 Introduction The ASPECT 2000D contains a powerful hierarchical Preset Subsystem Most of the functional groups have a local instance e g Proc Amp Aspect amp Zoom etc All of them are linked to a global Preset function which allows the user to define complete system setups Each of the local global preset functions provides 4 memory locations Via the Remote Control Software the user can assign a n
85. lASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 129 13 5 2 Recalling a local audio delay Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to audio 3 Press Select 4 Turn the rotary knob until the cursor points to delay 5 Press Select 6 Turn the rotary knob until the cursor points to Preset 7 Press Select 8 select the desired preset via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window audio delay 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 130 ASPECT 2000D User Manual 13 5 3 Saving a local audio delay Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to delay Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select OMONAARWN gt Via Shortcut n a Via Remote Control Software 1 Open the window audio delay 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 131 13 6 Audio Output
86. lified and more visi ble To avoid this a coring can be introduced It suppresses high frequency components below the se lected threshold which normally belong to the noisefloor of the input signal The enhancement and coring functions can be used either for luminance and chrominance sepa rately or for both components in the same manner ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 11 2 1 2000D User Manual 87 Horizontal Vertical Enhancement Via Menu O NLO OT e U OS Via Press Menu Turn the rotary knob until the cursor points to VidProc Press Select Turn the rotary knob until the cursor points to Enhance Press Select Turn the rotary knob to Y luminance or C chrominance or Y C both components Press Select adjust Enhancement to the desired level using the rotary knob Shortcut 1 2 3 Press horizontal Enhancement or vertical Enhancement The menu entry is Y C If separate adjustment is desired navigate back in the menu tree adjust Enhancement to the desired level level using the rotary knob Remote Control Software PONS Open the window Video Signal Processing Select Y C separate adjustment of luminance chrominance or Y C adjust Enhancement to the desired fort he horizontal and vertical direction when switching between Y C and Y C the systems keeps the different settings ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 88 ASP
87. m 2 Adjust the cropping by the appropriate slider besides the output window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 71 9 4 Aspect amp Zoom Background color The varying of geometric parameters like aspect zoom etc may produce a resulting image that does not fill the available monitor area For the regions that are not occupied by the image the systems allows to set a background color An independant second color can be setup for the output cropping area 9 4 1 Output background color zoom area Via the menu the color can be defined as Y Cb Cr coding The remote control software additionaly allows the definition as RGB format Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to ARC 3 Press Select 4 Turn the rotary knob until the cursor points to BG color 5 Press Select 6 Turn the rotary knob until the display shows zoom BG color in the upper row and Y val or Cb val or Cr val Press Select Set the zoom background color components using the rotary knob N Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Select the color coding format in the background color window 3 Set the zoom background color components ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 72 ASPECT 2000D User Manual 9 4 2 Output background color crop area Via the menu the col
88. med together A precision refer ence signal from a master sync generator must be applied to each device and genlocked so that the output of the equipment is synchronized with the timing of the reference By connecting the individual equipment to the timing reference source the processing delay of the equipment and the transmission delay of the cable connecting the equipment must be taken into account Individual timing adjustment must be made to compensate for the different delays For horizontal timing adjustment use the H POS option for the subcarrier to horizontal phase Fsc H the FSC H optionin an production environment it is common practice to operate all systems from a common sync source The black burst signal is often used for genlock equipment It is a composite signal without active video but has all synchronization signals The ASP erence ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ECT 2000D also accepts a composite video signal as ref 42 ASPECT 2000D User Manual 6 2 Genlock Operation we GENLOCK x eae erase H Delay ks QGREM v USERI vl pa 0 11 34 k CY FSCIH r 1274 3 TERMINATION mz 6 2 1 Genlock Activate Activates deactivates the Genlock Function Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Genlock 3 Press Select 4 Turn the rotary knob to activate deactivate Genlock Via Shortcut 1 Press
89. mp Several Predefinitions are available Blanked All VBI Lines blanked Blanked ITU insertion of standard ITU lines remaining area blanked Input ITU insertion of standard ITU lines remaining area filled with information from the input Input VBI area transparent 4 user Presets The generation of user presets is supported by the remote control software This function is not available via the local keyboard Via Menu Predefinitions OU ON BOON a Press Menu Turn the rotary knob until the cursor points to VBI Press Select Turn the rotary knob until the cursor points to Predef Press Select Select the desired predefinition by turning the rotary knob Via Shortcut n a Via Remote Control Software Predefinition 1 2 Via Remote Control Software detailed defintion line by line Open the window VBI recall the desired configuration via the Pre Definition field 1 2 define the desired pattern line by line Open the window VBI ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 51 8 1 2 Timecode inserter manual VITC line select Select the lines for VITC insertion There is an identical menu in the Timecode menu The setting can be done via both menues in the same manner Via Menu 2 ONS OP ONS lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until
90. n the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Sequence Press Select Select SEQ A or SEQ B as desired via the rotary knob CN Or Ol PONS Via Shortcut n a Via Remote Control Software 1 Open the window Audio Output 2 select the SDI tab 3 select the audio sequence Seq A or Seq B in the option field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 133 13 6 3 Audio Control Packet As the name AUDIO CONTROL PACKET indicates this data packet contains audio control information The audio control packet is transmitted once per field at a fixed position The control packet is optional for the default sampling rate of 48 kHz synchronous audio It must be transmitted for all other modes Each of the four audio groups has its own control packet This mode can be disabled if not required or the receiving unit can not handle this mode Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Audio 3 Press Select 4 Turn the rotary knob until the cursor points to Output 5 Press Select 6 Turn the rotary knob until the cursor points to CTLPACKETS 7 Press Select 8 Select ON or OFF via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Audio Output 2 select the SDI tab 3 select CPACKS in the option field When yellow controlpackets are enabled Mod
91. ntil the cursor points to display Press Select Turn the rotary knob until the cursor points to enable Press Select set Off or read or generate or both by turning the rotary knob Via Shortcut D OW BN Press timecode Turn the rotary knob until the cursor points to display Press Select Turn the rotary knob until the cursor points to enable Press Select set Off or read or generate or both by turning the rotary knob Via Remote Control Software 1 2 Open the window timecode select the desired display configuration ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 174 ASPECT 2000D User Manual 15 5 3 Timecode reader horizontal display position Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to display 5 Press Select 6 Turn the rotary knob until the cursor points to rd pos H 7 Press Select 8 set the desired horizontal position of the reader display by the rotary knob Via Shortcut 1 Press timecode 2 Turn the rotary knob until the cursor points to display 3 Press Select 4 Turn the rotary knob until the cursor points to rd pos H 5 Press Select 6 set the desired horizontal position of the reader display by the rotary knob Via Remote Control Software 1 Open the window timecode 2 select the desired display position ModelASPECT2000D Document UMASPECT2000D
92. oduction c cette ceee cee eeecneee sees eeeseeeeeseneeeseeeeees 180 16 2 Preset Operation cccsssssecesssssseeceeeeesseeeeeeeeeees 181 16 2 1 Storing of a global Preset 0 c ceeeeeeee 181 16 2 2 Recalling of a global Preset cccee 182 16 2 3 Assigning a name to a global Preset 183 16 3 Backup and Restore of Presets on the remote PC184 17 Maintenance cccccceceeesceeeeceeeeeeseneeees 17 14 MNTFOGUCTION vies ics eet eR kiose rannani ide nandai Ea 17 1 1 Version Display 17 1 2 Status Display oniinn ninaa 4 ASPECT 2000D User Manual 1 Introduction Dear user You have an ASPECT 2000D This machine gives you a broad variety of functionality Here is a short overview Video Proc Amp Frame store synchronizer Aspect ratio controller including WSS and VI Enhancement Noise Reduction with linear and median filters Legalizing Gamma correction optional Caption VBI Processing DV Firewire I O Timecode Generation Regeneration Audio Embedding Deembedding optional Audio Routing Delay and Level Control 1 1 Extent of Delivery The system comes with e CD including this documentation and the Remote Control Control Software occasionally optional e Power Chord Please check for completeness If items are missing please contact your dealer ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 1 2 Connecto
93. oftware 1 Open the window Timecode 2 activate the extended window 3 select the desired line in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 163 15 3 6 Timecode inserter RP188 activate Enable of the RP188 insertion into the outgoing video signals Via Menu SOON aAPWN gt lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to RP188 Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Shortcut ONONPWN gt Via Press Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to RP188 Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Remote Control Software 1 2 3 Open the window Timecode activate the extended window select On or Off in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 164 ASPECT 2000D User Manual 15 3 7 Timecode inserter manual RP188 line select Select the line for RP188 insertion Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn
94. on display To observe the impact of parameter change the screen can be split in various configurations Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Color 3 Press Select 4 select Display by turning the rotary knob 5 Press Select 6 select the desired display setting Via Shortcut n a Via Remote Control Software 1 Open the window Color Correction 2 select the desired display setting in the Display window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 104 ASPECT 2000D User Manual 11 7 Preset Color Correction 11 7 1 Recalling a color correction default Setup Predefinition The default setup provides a common disable to the color correction functions Via Menu Press Menu Turn the rotary knob until the cursor points to color Press Select Turn the rotary knob until the cursor points to Predef Press Select Select default by turning the rotary knob DEDS Via Shortcut n a Via Remote Control Software 1 Open the window color correction 2 Select default in the PRE Definition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 105 11 7 2 Recalling a local color correction Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to color 3 Press
95. ontent is more important than the quality This can be the case for news and documentary footage and to allow very powerful noise reduction to be used in forensic or surveillance applications In most cases a low setting may be constantly applied to give good reduction of minor video noise without impairing resolution of moving parts of the image This low setting gives a general clean up of the signal with minimum artifacts More severe noise should be dealt with by increasing the setting until the noise is just reduced to the required level If the noise is only in the chrominance or lumi nance domain then it is best to just remove it in that component ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 90 Via ASPECT 2000D User Manual Menu o N D0 Be OO NOS Via Press Menu Turn the rotary knob until the cursor points to VidProc Press Select Turn the rotary knob until the cursor points to Recursive Press Select Turn he rotary knob to Y luminance or C chrominance or Y C both components Press Select Turn the rotary knob to select the appropriate noise reduction factor Shortcut PON gt Press Recursive Turn he rotary knob to Y luminance or C chrominance or Y C both components Press Select Turn the rotary knob to select the appropriate noise reduction factor Remote Control Software PONS Open the window Video Signal Processing Select Y C separate adjustment of luminance
96. or can be defined as Y Cb Cr coding The remote control software additionaly allows the definition as RGB format Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to BG color Press Select Turn the rotary knob until the display shows crop BG color in the upper row and Y val or Cb val or Cr val Press Select Set the crop background color components using the rotary knob OV BO S oN Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Select the color coding format in the background color window 3 Set the crop background color components ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 73 9 5 Aspect amp Zoom Preset 9 5 1 Recalling a Aspect amp Zoom default Setup Predefinition The predefinition setup resets all zoom pan scan and crop settings to zero The input and output aspect settings will be maintained Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to predef Press Select Select the desired setting by turning the rotary knob DRN Via Shortcut n a Via Remote Control Software 1 Open the window Aspect ratio Conversion amp Zoom 2 Select the desired predefinition ModelASPECT2000D Document UMASPECT2000D 001 Rev
97. ovides a common disable to the filter functions Via Menu Press Menu Turn the rotary knob until the cursor points to VidProc Press Select Turn the rotary knob until the cursor points to Predef Press Select Select default by turning the rotary knob Oarhwn gt Via Shortcut n a Via Remote Control Software 1 Open the window Processing 2 Select default in the PRE Definition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 94 ASPECT 2000D User Manual 11 5 2 Recalling a local Filter Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to VidProc 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Processing 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 11 5 3 Saving a local Filter Preset 95 Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to VidProc Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Pres
98. pect Ratio Conversion amp Zoom 2 select configuration in the cursor settings field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 143 14 1 3 Cursor position horizontal left Numbers given as Y pixel Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Cursor 3 Press Select 4 Turn the rotary knob until the cursor points to Pos Left 5 Press Select 6 select the position by turning the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window Aspect Ratio Conversion amp Zoom 2 select the desired position for Cursor 1 or Cursor 2 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 144 ASPECT 2000D User Manual 14 1 4 Cursor position horizontal right Numbers given as Y pixel Via Menu Press Menu Turn the rotary knob until the cursor points to Cursor Press Select Turn the rotary knob until the cursor points to Pos right Press Select select the position by turning the rotary knob DOT EOS Via Shortcut n a Via Remote Control Software 1 Open the window Aspect Ratio Conversion amp Zoom 2 select the desired position for Cursor 1 or Cursor 2 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 145 14 1 5 Cursor position vertical top Numbers given as lines field Via Menu 1 Press Menu 2 Turn the rotary knob
99. ping by the appropriate slider besides the output window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 69 9 3 7 Output Cropping right Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to Out Right Press Select Adjust the Cropping using the rotary knob ONAARWN gt Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to Out Right 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 Adjust the cropping by the appropriate slider besides the output window ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 70 ASPECT 2000D User Manual 9 3 8 Output Cropping left Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Crop Press Select Turn the rotary knob until the cursor points to Out Left Press Select Adjust the Cropping using the rotary knob ONAAP ON Via Shortcut 1 Press Crop 2 Turn the rotary knob until the cursor points to Out Left 3 Press Select 4 Adjust the Cropping using the rotary knob Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoo
100. r clockwise to the desired format Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 select the desired input format via the active formats input field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 56 ASPECT 2000D User Manual 9 1 3 Selection of the output format Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to active format Press Select Turn the rotary knob until the cursor points to output Press Select Turn the rotary knob clockwise counter clockwise to the desired format SONATA WON gt Via Shortcut 1 Press Aspect once 2 Turn the rotary knob clockwise counter clockwise to the desired format Via Remote Control Software 1 Open the window Aspect ratio conversion and Zoom 2 select the desired input format via the active formats output field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 57 9 2 Zoom Pan amp Scan Independant of the aspect ratio settings the size and horizontal vertical scaling of the output image can be influenced manually 9 2 1 Manual adjustment of the output zoom factor Changing of the zoomfactor maintains the aspect ratio Via Menu Press Menu Turn the rotary knob until the cursor points to ARC Press Select Turn the rotary knob until the cursor points to Zoom
101. rator After the match occurs the generator proceeds for a number of frames which is setup via the orange section in the after stop section The following conditions are available e manual The generator manually stops with a click on the stop button e when input becomes invalid The generator stops when the input timecode gets invalid e when input matches The generator stops when the input timecode matches the stop value AFTER STOP CONDITION Please refer to the red subwindow The selected condition is transfered to the generator by pressing the immediate stop button This field defines the status of the generator after the stop procedure is accomplished The following conditions are available e timecode insertion off The insertion of timecode into the outgoing video signal is swiitched off e user value The output timecode remains valid but shows the defined user value e last valid timecode The ouput timecode remains valid but shows the last valid value e continue timecode The output continues to produce a timecode without any interruption Clicking the pause button stops the generator while all conditions setup previously are maintained Another click on the pause button unlocks the generator so that it continues from the current state ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 170 ASPECT 2000D User Manual 15 4 3 Keyboard setting of the generator mode Via Menu 1 Press Menu 2 Turn the ro
102. recall the complete setup configuration of the system into an Excel File 1 Open the window Preset 2 click on Save Setting to file or Load Setting to file ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 185 17 Maintenance 17 1 Introduction The maintenance function provides the user with some essential basic information about the system configuration and the status 17 1 1 Version Display The function enables the display of the current software status of the system Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Maint 3 Press Select 4 Turn the rotary knob until the cursor points to Version OSD 5 Press Select 6 The display shows the current software status of the system Via Shortcut n a Via Remote Control Software n a ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 186 ASPECT 2000D User Manual 17 1 2 Status Display The function enables the display of several screens which contain technical infomation about the sta tus of the internal processing blocks Please refer to this screens in case of system failure Via Menu Press Menu Turn the rotary knob until the cursor points to Maint Press Select Turn the rotary knob until the cursor points to Status OSD Press Select Turn the rotary knob to select the desired maintenance screen D E O N Via Shortcut n a Via Remote Control Softwar
103. red ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 34 ASPECT 2000D User Manual 4 2 3 Saving a local Proc Amp Preset Up to 4 local preset configurations can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to Procamp Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NOaPRwns Via Shortcut n a Via Remote Control Software 1 Open the window Proc Amp 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 5 Video Output 5 1 System Output Settings OUTPUT STANDARD FRESET NTSC358 e ac eee FON pycam Tae CVCFRO o OFERATE BYPASS FAMENNE ___ OFF _ FATTEEN SELECT ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 35 36 ASPECT 2000D User Manual 5 1 1 Output Standard Selection The vertical frequency of the output follows the signal on the input of the system That means it is not possible to directly select a desired output standard Select an appropriate input standard instead 5 1 2 Output Bypass By selecting bypass to ON the inputs of the system are directly bypassed to the corresponding out puts This function is not supported by the SDI I O and the Firewire I O Via Menu Press Menu Turn the rotar
104. rominance Range 8lines 7 lines in steps of 1line Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Procamp 3 Press Select 4 Turn the rotary knob until the cursor points to Timing 5 Press Select 6 Turn the rotary knob until the cursor points to Y C 7 Press Select 8 Turn the rotary knob until the cursor points to Pos V 9 Press Select 10 Adjust by turning the rotary knob Via Shortcut 1 Press Timing 2 Turn the rotary knob until the cursor points to Y C 3 Press Select 4 Turn the rotary knob until the cursor points to Pos V 5 Press Select 6 Adjust by turning the rotary knob Via Remote Control Software 1 Open the window Proc Amp 2 adjust Pos V to the desired position ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 31 4 1 10 Input vertical Chroma Position Adjustment of the vertical input chroinance timing Range 8lines 7 lines in steps of line Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Procamp 3 Press Select 4 Turn the rotary knob until the cursor points to Timing 5 Press Select 6 Turn the rotary knob until the cursor points to C to Y 7 Press Select 8 Turn the rotary knob until the cursor points to C Pos V 9 Press Select 10 Adjust by turning the rotary knob Via Shortcut 1 Press Timing 2 Turn the rotary knob until the cursor points to C to Y 3
105. rs This rear panel view shows the connectivity of the system Optional connectors are shown with grey background Genlock Inputs LTC Input SDI Input Digital Audio Inputs Analog Audio Inputs CVBS Inputs Analog Audio Outputs Digital Audio Outputs LTC Output in DV Firewire SDI Output 1 0 RS 232 Port for Remote Control Power The power connector conforms to IEC 60320 1 C14 The unit accepts 100 260VAC with either 50Hz or 60Hz Analogue Audio Inputs The unit supports 4 independant analog audio channels The first channel is located leftside besides the power connector rear view The audio connectors use mini XLR plugs Standard input levels are calibrated to OdBu 15dBfs Connector assignment Input 1 Audio 1 left channel Input 2 Audio 1 right channel Input 3 Audio 2 left channel Input 4 Audio 2 right channel ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 Digital Audio Inputs LTC Input DV Input Output SDI Input Analogue Genlock Inputs RS232 Port for Remote Control Analogue Audio Outputs Digital Audio Outputs LTC Output SDI Output optional ASPECT 2000D User Manual Two input connectors for AES EBU or S PDIF signals are provided The first input is located left rear view besides the analog audio The connectors are
106. s Select NDRRON Via Shortcut n a Via Remote Control Software 1 Open the window filter 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 96 ASPECT 2000D User Manual Color Correction 11 6 Introduction The ASPECT 2000D can is equipped with a versatile RGB color correction The structure of this func tional block is shown below In a first step the black and white level of the raw signal can be realigned The result is fed into the gamma correction followed by the post black and white level correction wv COLOR CORRECTION x SAVE GLOBAL v USERI v PRE DEFINITIONS DEFAULT v 00 ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 11 6 1 Color Correction Enable 97 This allows to bypass the color correction block without affecting its setting Via Menu Press Menu Turn the rotary knob until the cursor points to Color Press Select PoON gt Via Shortcut select ON or OFF by pressing Select again It acts as a toggle key n a Via Remote Control Software 1 Open the window Color Correction 2 Select ON or OFF in the color corrector field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 98 ASPECT 2000D User Manual 11 6 2 Color Correction pre white level The settings can be made independ
107. s Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to DV TC Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Remote Control Software Open the window Timecode activate the extended window select On or Off in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 166 ASPECT 2000D User Manual 15 3 9 Timecode inserter LTC format The LTC output supports both EBU and SMPTE format Via Menu a 0 OA OE ONS lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to LTC Press Select Turn the rotary knob until the cursor points to mode Press Select select EBU or SMPTE via the rotary knob Shortcut D NDN ONS Via Press Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to LTC Press Select Turn the rotary knob until the cursor points to mode Press Select select EBU or SMPTE via the rotary knob Remote Control Software 1 2 3 Open the window Timecode activate the extended window select On or Off in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPEC
108. s to Gain Predef Press Select Select default by turning the rotary knob ONONRWN gt Via Shortcut n a Via Remote Control Software 1 Open the window audio processing 2 Select default in the Gain Predefinition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 122 ASPECT 2000D User Manual 13 3 2 Recalling a Audio Level default Setup Predefinition The default audio level setup forces the level sliders of all channels to OdB Via Menu Press Menu Turn the rotary knob until the cursor points to audio Press Select Turn the rotary knob until the cursor points to processing Press Select Turn the rotary knob until the cursor points to Level Predef Press Select Select default by turning the rotary knob COO Clie po Po a Via Shortcut n a Via Remote Control Software 1 Open the window audio processing 2 Select default in the Level Predefinition field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 123 13 3 3 Recalling a local audio input processing Preset The local Preset covers level and gain settings work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to audio 3 Press Select 4 Turn the rotary knob until the cursor points to processing 5 Press Select 6 Turn the rotary knob until
109. sed noise reduction filters is very effective in the reduction or elimination of noise that is random in nature This is achieved by feeding the signal back on itself to accumulate more than one frame of picture information Pixels that are present in all frames can then be identified as useful information Pixels that change randomly can then be treated as noise and removed Typical examples of sources that contain random noise that can be effectively treated in this way are camera noise generated when operating under low light high gain conditions film grain tape noise analog VCR s and general video noise from poor sources or multiple generations As a general rule only the minimum amount of recursive noise reduction should be applied to the sig nal to correct the problem If the unit is left with a high setting made for one source it may be inappro priate for another source that contains less noise or noise with a different footprint If the setting is too high some smearing of motion occurs A high setting provides enormous amounts of noise elimination but will cause significant movement problems These settings are only for use where material is totally unusable at lower settings At these levels images can be retrieved from signals that are so impaired that they might not even appear to contain real pictures The higher levels are included to deal with material that may need to be broadcast but is of very poor quality i e where the c
110. signal The two patterns Colorbars and Black are directly accessable via shortcuts Via Menu Press Menu Turn the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Operate Press Select Select Video or Test OunPRWN gt Via Shortcut 1 Press Black or Bars 2 The selected Pattern will appear on the output To return to video press the key again 3 Selecting Black or Bars via the shortcut keys overwrites other selections Via Remote Control Software 1 Open the window Output 2 click Operate to show the current video signal 3 click Pattern to show the selected test pattern 4 select the desired test pattern by clicking Bars or Black or various ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 48 7 1 2 ASPECT 2000D User Manual Test Pattern Selection The two patterns Colorbars and Black are directly accessable via shortcuts Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Pattern 3 Press Select 4 select the desired test pattern by turning the rotary knob Via Shortcut 1 Press Black oder Bars 2 The selected Pattern will appear on the output To return to video press the key again 3 The menu shows the selected test pattern Select other test patterns by turning the rotary knob Via Remote Control Software 1 Open the window Output 2 select the desired test pattern by clic
111. ss Select 4 Turn the rotary knob until the cursor points to Operation 5 Pressing Select toggles between On and Off Via Shortcut n a Via Remote Control Software 1 Open the window Processing 2 Select On or Off ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 86 ASPECT 2000D User Manual 11 2 Enhancement Aperture Correction The enhancement capability is provided to allow a perceived improvement on picture resolution In dependent control over the horizontal and vertical frequencies as different amounts of enhancement may be appropriate The use of positive values for enhancement boost certain high frequency com ponents of the signal to provide a visual sharpening of edges and improvement of resolution If the image is soft great improvements can be made If the input image is already good then the use of too much enhancement will cause ringing on the edges of objects which is not desirable The other danger of using too much enhancement is the boosting of noise frequencies The use of negative values effectively reduce resolution This feature is provided to allow the filtering of higher frequency picture correlated noise i e unwanted information that does not move signifi cantly between frames and so will not be reduced by the recursive filtering process as it is impossi ble to determine whether it is wanted picture information or not This type of problem would be present on the input signal and may be
112. t 160 15 3 4 Timecode inserter RP196 activate 161 15 3 5 Timecode inserter manual RP196 line select 162 123 15 3 6 Timecode inserter RP188 activate 00 0 163 15 3 7 Timecode inserter manual RP188 line select 164 15 3 8 Timecode inserter DV TC activate 165 15 3 9 Timecode inserter LTC format ccee 166 15 4 Timecode Generator scccssccsecsseeceeeeseeeeeeeees 167 15 4 1 Introduction ccc cece eeeeeeeeceeeeeesaeeeeeeeeeeees 167 15 4 2 Normal and Expertmode ccccccecceeeeeeeees 168 15 4 3 Keyboard setting of the generator mode 170 15 4 4 Keyboard setting of the generator start value 171 15 4 5 Keyboard setting of the generator dropframe MOGs 22 2252s ETT AEE 172 15 5 Timecode Display cccsseccceessseeeeeeeeeseseeeenees 173 15 5 1 Introduction 2000 eee eect ee eet eeetee eee eeteettaeeeeeeeeeeaee 173 15 5 2 Timecode Display Enable cceeeeeeeee 173 15 5 3 Timecode reader horizontal display position 174 15 5 4 Timecode reader vertical display position 175 15 5 5 Timecode generator horizontal display position176 15 5 6 Timecode generator vertical display position 177 15 6 Timecode Preset c ccessecssseeeesesneeeseneeeeeneeeees 178 15 6 1 Recalling a local timecode Preset 5 178 15 6 2 Saving a local timecode Preset 0 00 179 16 Preset ission 180 16 1 Intr
113. tary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to generator 5 Press Select 6 Turn the rotary knob until the cursor points to mode 7 Press Select 8 select the desired mode jam sync or input or flywheel by turning the rotary knob Via Shortcut 1 Press timecode 2 Turn the rotary knob until the cursor points to generator 3 Press Select 4 Turn the rotary knob until the cursor points to mode 5 Press Select 6 select the desired mode jam sync or input or flywheel by turning the rotary knob ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 171 15 4 4 Keyboard setting of the generator start value Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to timecode 3 Press Select 4 Turn the rotary knob until the cursor points to generator 5 Press Select 6 Turn the rotary knob until the cursor points to TC start value 7 Press Select 8 set hours by turning the rotary knob 9 Press Select 10 set minutes by turning the rotary knob 11 Press Select 12 set seconds by turning the rotary knob 13 Press Select 14 set frames by turning the rotary knob 15 Press Select 16 confirm the setting Via Shortcut 1 Press timecode 2 Turn the rotary knob until the cursor points to generator 3 Press Select 4 Turn the rotary knob until the cursor points to TC start value 5 Press Select
114. tcut Press Timecode Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to MASTER EN Press Select select On or Off via the rotary knob PARON Via Remote Control Software 1 Open the window Timecode 2 activate the extended window 3 select On or Off in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 15 3 2 Timecode inserter VITC activate 159 Enable of the VITC insertion into the outgoing video signals Via Menu SOON aAPWN gt lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Shortcut ONONPWN gt Via Press Timecode Turn the rotary knob until the cursor points to inserter Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to activate Press Select select On or Off via the rotary knob Remote Control Software 1 2 3 Open the window Timecode activate the extended window select On or Off in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 160 ASP
115. the Genlock key in the rightmost field 2 Press Select 3 Turn the rotary knob to activate deactivate Genlock Via Remote Control Software 1 Open the window Genlock 2 click On Off Nodet off The system is synchronized internally from the input signal lock This message appears if the genlock mode is on and the external synchronization sig nal is recognized and the system is locked lock H lock without FSC lock nolock This message appears if the genlock mode is on but is not locked to the external source ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 43 6 2 2 Genlock H Delay Defines the horizontal delay between reference and output signal Range 16 0usec 15 96usec in steps of 37ns The display shows n a if no valid input signal is available Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to Genlock 3 Press Select 4 Turn the rotary knob until the cursor points to H Pos 5 Press Select 6 select the desired value via the rotary knob Via Shortcut 1 Press the Genlock key in the rightmost field 2 Turn the rotary knob until the cursor points to H Pos 3 Press Select 4 Turn the rotary knob to adjust to the desired value Via Remote Control Software 1 Open the window Genlock 2 change H Delay as desired Genlock Signal Y Output Signal
116. the cursor points to inserter Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to OUTPOS Press Select select the desired lines Shortcut CN C1 GN Via Press Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to OUTPOS Press Select select the desired lines Remote Control Software 1 2 3 Open the window VBI activate the extended window select the desired lines in the inserter field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 52 ASPECT 2000D User Manual 8 2 VBI Preset 8 2 1 Recalling a local VBI Preset work current status user 1 4 user defined local preset global user defined global preset Via Menu 1 Press Menu 2 Turn the rotary knob until the cursor points to VBI 3 Press Select 4 Turn the rotary knob until the cursor points to Preset 5 Press Select 6 select the desired setting via the rotary knob Via Shortcut n a Via Remote Control Software 1 Open the window VBI 2 change setting in the Preset field as desired ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 8 2 2 Saving a local VBI Preset 53 Up to 4 local prest configurations can be stored as user 1 user 4
117. tions can be stored as user 1 user 4 Via Menu Press Menu Turn the rotary knob until the cursor points to legalizer Press Select Turn the rotary knob until the cursor points to Save Preset Press Select select the desired Preset via the rotary knob Press Select NOaPRwns Via Shortcut n a Via Remote Control Software 1 Open the window legalizer 2 select the desired Preset ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 113 13 Audio Processing 13 1 Introduction The complexity of routing distributing and processing audio causes increasing problems in maintain ing the audio to video delay This problem happens if audio and video is processed separately Nothing is worse than lip sync problems The ASPECT 2000D gives you a variety of options to work with audio Audio Data Redistribution SDI Interface Embedded Audio Support for 32kHz 44 1kHz 48 kHz external Audio Interface AES EBU Standard S PDIF Standard Analog Standard Embedded Audio Support Audio Dropout Compensation Audio Resampling DV Interface One of the important advantages of SDI Serial Digital Interface is the ability to embed multiplex several channels of digital audio in the digital video signal This is particularly useful to assure that the audio is associated with the appropriate video The SMPTE 272M standard defines the mapping of AES EBU digital audio dat
118. to autosel Press Select select auto or manual via the rotary knob Remote Control Software 1 2 3 Open the window Timecode activate the extended window select auto or manual in the VITC position field ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 156 ASPECT 2000D User Manual 15 2 3 Timecode Reader manual VITC line select Allows the manual line select on the VITC input Via Menu 0 2 SO Or BQ NS lt 5 Press Menu Turn the rotary knob until the cursor points to timecode Press Select Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to INPOS Press Select Select the desired line viia the rotary knob Shortcut ONO Oi OO NS Via Press Timecode Turn the rotary knob until the cursor points to reader Press Select Turn the rotary knob until the cursor points to VITC Press Select Turn the rotary knob until the cursor points to INPOS Press Select select the desired line viia the rotary knob Remote Control Software 1 2 3 Open the window Timecode activate the extended window select the desired line number out of the list Lines marked in black carry valid VITC ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 157 15 2 4 Keyboard setting of the reader dropframe mode Via
119. ways valid ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 168 ASPECT 2000D User Manual 15 4 2 Normal and Expertmode Under normal circumstances it should be suficient to select some basic parameters like input source operation mode of the generator flywheel etc and some output configuration This will cover the majo rity of the applications But in some cases more sophisticated setup conditions are necessary For these applications the timecode generator provides several additional tools They are summarized as expert tools and available via the remote control software but not via the local keyboard To use these tools efficiently it is important to keep track about the overall status of the timecode sub system and this is hard to maintain using the small display of the local keyboard The expert mode of the timecode generator will be automatically reset when any generator function is addressed via the local keyboard A This avoids potential deadlocks which may occur because the features of the expert mode are not available here The following explanation refers to the Timecode window of the remote control software with Expert Mode enabled BEFORE START Please refer to the blue subwindow The selected condition is transfered to the generator by pressing the initialize button Before getting started the system must be set to a defined status The following conditions are available e timecode
120. y knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Bypass Press Select select Bypass ON or OFF anrhwoNs Via Shortcut 1 Press Bypass 2 the key acts as a toggle key Pressing bypass again switches back to the system output Via Remote Control Software 1 Open the window Output 2 select Bypass ON or OFF ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 5 1 3 Freeze 37 Stores one frame and reads it out repeatedly Via Menu Press Menu Turn the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to Freeze Press Select selcect ON or OFF OF OB Ns Via Shortcut 1 Press the key Freeze in the picture field The function will toggle between ON and OFF Via Remote Control Software 1 Open the window Mode 2 select Run or Freeze ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 38 ASPECT 2000D User Manual 5 1 4 Output DV Format The system supports two DV formats DVCAM gt Colourcoding 4 2 0 DVCAM miniDV DV DVCPRO gt Colourcoding 4 1 1 DVCPro Via Menu Press Menu Turn the rotary knob until the cursor points to Output Press Select Turn the rotary knob until the cursor points to DV FORMAT Press Select Select DVCAM or DVCPRO OF Or ON Via Shortcut n a Via Remote Control Software 1 Open th
121. ystem and click on Select Alternatively you can double click on the selected list entry Then the software connects to the system and recalls all the windows and their positions as they were specified at the last session ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 14 2 Housekeeping Functions 2 1 Introduction This chapter describes some basic setup functions 2 1 1 Keyboard button lights ASPECT 2000D User Manual Controls the intensity of the button lights Via Menu Press Menu Turn the rotary knob until the cursor points to Panel Press Select Turn the rotary knob until the cursor points to LED BRIGHT Press Select Turn the rotary knob to adjust the intensity E Via Shortcut n a Via Remote Control Software n a Keyboard display contrast Controls the contrast of the alphanumeric readout Via Menu Press Menu Turn the rotary knob until the cursor points to Panel Press Select Turn the rotary knob until the cursor points to Contrast Press Select Turn the rotary knob to adjust the contrast DUE OPa Via Shortcut n a Via Remote Control Software n a ModelASPECT2000D Document UMASPECT2000D 001 Rev ASPECT2000D 001 ASPECT 2000D User Manual 3 Video Input 3 1 Input Source and Standard Selection SOORCE STANDARD PRESET NTSC35 SUTGSECECE DV FORMAT DVCAM a I COLOR j DV IN OUT

Download Pdf Manuals

image

Related Search

Related Contents

leggi istr.  B412 和算箱  Ficha técnica Bio-Q Solución  製品安全データシート  2019-DCB Users Guide 5B2302.vp  Panasonic HDC-SD10  Guide d`auto-évaluation du contrôle de gestion à l`usage des  OpenOffice.org OpenOffice - 3.3 Getting Started Guide  

Copyright © All rights reserved.
Failed to retrieve file