OptoLyzer MOCCA compact V3.1 User Manual
Contents
1. CONNECTING NETWORKS OptoLyzer MOCCA compact V3 1 D SAA Ad SE EAI OPtoLyzere Copyright 2013 K2L GmbH K2L All rights reserved Please make sure that all information within a document marked as Confidential or Restricted Access is handled solely in accordance with the agreement pursuant to which it is provided and is not reproduced or disclosed to others without the prior written consent of K2L The confidential ranking of a document can be found in the footer of every page This document supersedes and replaces all information previously supplied The technical information in this document loses its validity with the next edition Although the information is believed to be accurate no responsibility is assumed for inaccuracies Specifications and other documents mentioned in this document are subject to change without notice K2L reserves the right to make changes to this document and to the products at any time without notice Neither the provision of this information nor the sale of the described products conveys any licenses under any patent rights or other intellectual property rights of K2L or others The products may contain design defects or errors known as anomalies including but not necessarily limited to any which may be identified in this document which may cause the product to deviate from published descriptions Anomalies are described in errata sheets available upon request K2L products are not designed intend2. compact Both trigger variants are realized using a LIN transceiver For the pin out refer to Section 6 9 ECL on page 25 The device can be reset by the push button If the button is pressed for less than 1 s the device is reset The same button is used for switching into the flashing mode For details see the K2L Flasher Online Help that is part of the shipment The OptoLyzer MOCCA compact provides one analog audio Line IN The analog Line IN input impedance is 10 kQ The analog input are converted into digital streams with resolutions of 8 16 or 24 bits channel both mono and stereo It has a 3 5 mm jack plug The relay is able to switch 5A as a potential free shutter For safety purposes refer to Chapter 2 Safety Instructions on page 9 For the pin out refer to Section 6 8 Relay on page 25 This interface is only available on platforms that are supporting MOST Each OptoLyzer MOCCA compact has only one MOST connector i e either a MOST150 connector or a MOST50 connector The MOST50 connector bases on an electrical physical layer ePhy whereas the MOST150 connector bases on an optical physical layer oPhy For the pin out refer to Section 6 10 MOST Connector on page 26 The USB port is a standard USB B type receptacle The LAN connector is an RJ45 receptacle according to TIA 568 3 17 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual The OptoLyzer MOCCA compact offers
3. o ooooocononononono oo 21 Table 6 2 Pin Assignment of Connector High Speed CAN 2 4 6 o oooooonoronono oo 22 Table 6 3 Pin Assignment of Connector LIN FlexRay A B 2 on nennen 22 Table 6 4 Pin Assignment of Connector LIN Low Speed CAN 0 0 0 cee ee ee ee 23 Table 6 5 Pinning of the Sync and Power Connector o o oooooon een nn 23 Table 6 6 Pin Assignment of the Relay Connector o o oo oooooooo nennen 25 Table 6 7 Technical Values none ee ee ee ee ee nenn 25 Table 6 8 Pin Assignment of the MOST50 Connector 2 2 2222 unseren nennen ee 26 Table 7 1 Device and Bus Characteristics ee ee ee ee ee ee ee ee een ee ee ee ee ee 27 Table 7 2 Mechanical Characteristics Lee ee ee ee ee ee ee ee ee ee 27 Table 7 3 Electrical Characteristics Lee ee ee ee ee ee ee ee ee ee ee een nen 28 Table 8 1 Customer Revision History ever ee ee ie ie ee ee ee ee ee ee ee ee ee eis 29 K2L OptoLyzer MOCCA compact V3 1 5 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 1 Preface 1 1 Intended Use The OptoLyzer MOCCA compact is intended to be used for developing testing or analyzing CANO FlexRay LIN or MOST based automotive products and systems by persons with experience in developing automotive devices 1 2 Scope of Delivery The OptoLyzer MOCCA compact is the hardware part of the following K2L produc
4. wall power supply or by any other power supply which is capable to deliver 12 V and 1 A If the wall power supply is not used the included power cable has to be used to connect the 12 V supply with the OptoLyzer MOCCA compact For the pin out refer to Section 6 4 Synchronization and Power on page 23 K2L OptoLyzer MOCCA compact V3 1 19 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 5 3 Connectors on the Rear Panel INTERFACE DESCRIPTION S PDIF Only OptoLyzer MOCCA compact platforms supporting MOST MOST50 as well as IN MOST150 offer an S PDIF The output is compliant to the specification IEC 60958 4 OUT with 75 Q and 0 5 Vpp 20 The output is short circuit proof The input circuit expects an unbalanced input and has an impedance of 75 0 Input sample rates from 32 to 96 kHz are accepted For the pin out refer to Section 6 5 Digital Audio In Out S PDIF on page 24 The OptoLyzer MOCCA compact offers the bidirectional transfer of audio streams between the MOST synchronous channel and the S PDIF connectors An audio stream on a MOST synchronous channel can be routed to the S PDIF output of the device It is also possible to route a digital audio stream from S PDIF input of the device to the MOST synchronous channel at the same time The following tables describe which S PDIF formats are supported by the OptoLyzer MOCCA compact Direction S PDIF IN to MOST S PDIF data from an exter
5. 2 are terminated with 120 Q at each end Therefore the OptoLyzer MOCCA compact does not terminate the bus The transmission speed ranges from 33 kbits s to 1 Mbits s 4 3 1 2 Low Speed Transceiver Low speed CAN bus systems usually have a distributed termination The value of the termination in each node depends on the number of nodes in the network To avoid effects on the total impedance of the network the OptoLyzer MOCCA compact has a weak termination of 5 6 kO A communication via the low speed transceivers ranges up to 125 kbits s Revision 1 0 04 29 13 12 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 3 1 3 Single Wire Transceiver The single wire CAN is terminated with 9 1 kQ The transmission speeds for single wire CAN are 33 kbits s on board communication and 83 kbits s off board communication 4 3 2 FlexRay The termination of a FlexRay bus depends on the bus topology Two terminations are mandatory in each active branch The OptoLyzer MOCCA compact can be installed in various topologies Therefore a termination is not implemented in the device Thus the terminations have to be realized in a different way In addition the OptoLyzer MOCCA compact does not act as a bus guardian The OptoLyzer MOCCA compact provides one FlexRay bus and is able to switch from sleep mode to wake up mode stimulated by the FlexRay bus The bus is capable of transmitting up to 10 Mbit s brutto as per Ele
6. ca Is RS ICI IO ECN mm CECI 6 2 LIN FlexRay Connector type see Figure 6 1 DE 9 The provided GND pin must not be used unless there is no other GND connection This pin must not be used for supply purpose Table 6 3 Pin Assignment of Connector LIN FlexRay A B CI A a ee Posi a rn Revision 1 0 04 29 13 22 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 3 LIN Low Speed CAN and Single Wire CAN 2 6 Connector type see Figure 6 1 DE 9 The provided GND pin must not be used unless there is no other GND connection This pin must not be used for supply purpose Table 6 4 Pin Assignment of Connector LIN Low Speed CAN ELISE SE a zer ET es Ga io wie ICI emo CEN 6 4 Synchronization and Power Figure 6 2 shows the pin assignment as it is visible on the rear panel Figure 6 2 Pin Assignment of the Sync and Power Connector Table 6 5 Pinning of the Sync and Power Connector DESCRIPTION K2L OptoLyzer MOCCA compact V3 1 23 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 5 Digital Audio In Out S PDIF Both digital connectors S PDIF In Out interface to a RCA phono socket Signal Figure 6 3 Pin Assignment of the S PDIF Connector The input circuit expects an unbalanced input and has an impedance of 75 0 The shield connects to system ground 6 6 Analog Audio In Out Both the stereo line in and
7. seven LEDs All LEDs except the Power LED are tri colors Table 5 2 LEDs INTERFACE SYMBOL DESCRIPTION COLOR DESCRIPTION Active Active This LED indicates any Reseved activity Operation This LED indicates different Red Depending on firmware states dependent on the ATS etc state of the CAN bus White Bus activity Flashing state of the MOST network platforms that are supporting MOST White Bus activity Flashing state of the FlexRay bus White Bus activity Flashing state of the LIN bus White Bus activity Flashing Power This LED indicates a Green Powered device powered device Revision 1 0 04 29 13 18 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 5 2 Rear Panel Different hardware platforms and software configurations are available for the OptoLyzer MOCCA compact As a result some connectors might not be available for a specific variant of the OptoLyzer MOCCA compact Figure 5 1 depicts a platform supporting MOST150 Bas reli Mitad High Seo CAN pudo or Sync Power C va A art EE LIN Low Speed CAN SO Es aN IN VOUT Figure 5 2 Rear Panel E G with S PDIF Interfaces All components of the rear panel are described below Table 5 3 describes the connectors from top to bottom and left to right Table 5 3 Connectors on the Rear Panel INTERFACE DESCRIPTION High Speed CAN These two connectors offer six high speed CAN instances with b
8. the headphone stereo output interface to an audio phone connector Right Audio Signal 4 GND Left Audio Signal Figure 6 4 Pin Assignment of the Analog Audio In Out Connector 67 USB The USB port is a standard USB B type receptacle Revision 1 0 04 29 13 24 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 8 Relay The relay is able to switch 5A as a potential free shutter Please refer also to Chapter 2 Safety Instructions on page 9 Relay type m assembled connector type RIA 31182102 m connector type to be plugged RIA 31169102 The pin assignment below is described as it is visible on the front panel Table 6 6 Pin Assignment of the Relay Connector PIN NUMBER DESCRIPTION 1 left pin Shutter input 2 right pin Shutter output 6 9 ECL This connector provides two pins The upper pin is for connecting the ECL Trigger signal the lower pin for connecting GND Connector type m assembled connector type Molex 43045 0201 m connector type to be plugged Molex 43025 0200 Table 6 7 Technical Values PARAMETER VALUE K2L OptoLyzer MOCCA compact V3 1 25 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 6 10 MOST Connector 6 10 1 MOST50 Connector type AMP 1376350 1 Figure 6 5 shows the pin assignment as it is visible on the front panel Figure 6 5 PIN Assignment of the MOST50 Connector Table 6 8 Pin Assignme
9. CA compact is able to scan the six CAN buses in sleep mode and if stimulated to switch from sleep mode into wake up mode In addition the OptoLyzer MOCCA compact can be waked up via FlexRay LIN or ECL K2L OptoLyzer MOCCA compact V3 1 15 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 5 Hardware Description 5 1 Front Panel Different hardware platforms are available for the OptoLyzer MOCCA compact Figure 5 1 depicts a platform supporting MOST150 Program Reset OptoLyzer Figure 5 1 Front Panel E G All components of the front panel are described below Table 5 1 describes the connectors from left to right and top to down whereas Table 5 2 describes the LEDs Revision 1 0 04 29 13 16 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 5 1 Connectors on the Front Panel INTERFACE SYMBOL DESCRIPTION Analog Audio Out ECL or Trigger Program Reset Program Reset Analog Line IN K2L OptoLyzer MOCCA compact V3 1 The OptoLyzer MOCCA compact provides one headphone stereo output It has a 3 5 mm jack plug Output Power Py Max Rms 1 4 mW at R 16 Q Vout 150 MVRms OptoLyzer MOCCA compact platforms supporting MOST m ECL can be used to wake up the OptoLyzer MOCCA compact according to different ECL implementations OptoLyzer MOCCA compact platforms without MOST The trigger can be used to wake up the OptoLyzer MOCCA
10. al Commission http www iec ch Revision 1 0 04 29 13 8 K2L USER MANUAL K2L OptoLyzer MOCCA compact V3 1 OptoLyzer MOCCA compact User Manual Chapter 2 Safety Instructions 2 1 Supply and Synchronization The OptoLyzer MOCCA compact devices could be cascaded via Sync Power connector One of the two Sync Power connectors is intended to be used for the power supply and the other for cascading the OptoLyzer MOCCA compact by using an optional sync cable During cascading caution has to be taken since the first device in the chain can take the maximum current of 3 A Do not cascade more than eight devices in chain For all setups either a fuse of max 4 A in the supply cable to the first device or the use of the current limitation of the laboratory power supply is mandatory 2 2 Relay The Relay feature of the device is designed to switch other 12 V powered devices The capability is limited to 5A at 16 V maximum Always use core cable ends of appropriate length and diameter to prevent unintended connections K2L OptoLyzer MOCCA compact V3 1 9 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 3 Definitions Limit Class 3 1 Emission The OptoLyzer MOCCA compact has passed the requirements according to the standard EN 55022 2010 class A Warning The OptoLyzer MOCCA compact is a class A product In a domestic environment this product may cause radio interference in which case the user may b
11. aud rates from 40 kbit s 1 3 5 to 1 Mbit s depending on the cable length The CAN instances 1 3 4 and 5 are hard 2 4 6 specified as high speed CAN interfaces whereas the CAN instances 2 and 6 can also be used as low speed or as single wire CAN interfaces The CAN interfaces can be controlled by a customer application Details about the CAN bus properties are described in Section 4 3 1 CAN on page 12 For the pin out refer to Section 6 1 High Speed CAN on page 21 LIN FlexRay This DE 9 socket combines pins assigned to the FlexRay bus and pins assigned to the LIN channels 3 4 5 and 6 For the pin out refer to Section 6 2 LIN FlexRay on page 22 LIN Low Speed This DE 9 socket combines two low speed and two single wire CAN interfaces CAN CAN instances 2 and 6 as well as two LIN channels 1 and 2 These CAN instances can be Single Wire CAN 2 6 used either as high speed CAN interfaces or as low speed CAN interfaces or as single wire CAN interfaces These CAN interfaces can be controlled by a customer application For the pin out refer to Section 6 3 LIN Low Speed CAN and Single Wire CAN 2 6 on page 23 The Synchronization Sync and the Power connector have the identical pin assignment i e each socket can be used either for synchronization or power purposes Restrictions are described in Section Chapter 2 Safety Instructions on page 9 The OptoLyzer MOCCA compact is intended to be powered by the optional available
12. compact and the embedded OS81082 INIC is realized by MediaLB 3 Pin with 1024Fs MOST 150 Data exchange between the OptoLyzer MOCCA compact and the embedded OS81110 INIC is realized by MediaLB 6 Pin with 2048Fs SpyNIC for MOST Each speed grade of an OptoLyzer MOCCA compact has also an appropriate SpyNIC for MOST on board Both speed grade variants of the SpyNIC are spying control packet and allocation messages A node is realized at the same time The accuracy of SpyNIC time stamps is 1 us StressNIC for MOST Each speed grade of an OptoLyzer MOCCA compact has also an appropriate StressNIC for MOST on board Both speed grade variants of the StressNIC are supporting dedicated use cases for simulating some common network error situations e g light lock stress buffer full simulation etc By default the StressNIC for MOST is electrically bypassed but can be enabled by appropriate software e g ATS 1 An optical MOST25 interface is provided by the former hardware version MOCCA compact V2 3 Revision 1 0 04 29 13 14 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 3 5 Ethernet Auto MDIX is supported therefore the LAN interface can connect via straight and crossed patch cables The physical layer 100BASE TX is supported The OptoLyzer MOCCA compact is able to configure different MACs during run time The accuracy of Ethernet time stamps is 500 us 4 3 6 Sleep Mode The OptoLyzer MOC
13. ctrical Characteristics Relay for external load potential free 12 V DC shutter Revision 1 0 04 29 13 28 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 8 Revision History Table 8 1 Customer Revision History REVISION LEVEL amp SECTION FIGURE DATE ENTRY CORRECTION Rev 1 0 Initial Version 04 29 13 K2L OptoLyzer MOCCA compact V3 1 29 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Further Information For more information on K2L automotive products including integrated circuits software and MOST development tools and modules visit our web site http www K2L de Direct contact information is available at http www K2L de contact K2L GmbH Bannwaldallee 48 D 76185 Karlsruhe Germany Technical Support Contact information for technical support is available at http www K2L de contact Revision 1 0 04 29 13 30 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL
14. ctrical Physical Layer Specification Version 2 0 The accuracy of FlexRay time stamps is 500 us for the static part of the schedule 43 3 LIN Both LIN master and LIN slave functionality are supported The accuracy of LIN time stamps is 1 us The OptoLyzer MOCCA compact supports a maximum transmission speed of 20 kbit s brutto K2L OptoLyzer MOCCA compact V3 1 13 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 3 4 4 3 4 1 4 3 4 2 4 3 4 3 4 3 4 4 MOST The OptoLyzer MOCCA compact platform supporting MOST50 is able to switch the clock mode of the embedded OS81082 INIC and thus supports a 44 1 kHz as well as a 48 kHz network whereas the OptoLyzer MOCCA compact platform designed for a MOST150 network has a fixed clock mode of 48 kHz OptoLyzer MOCCA compact platforms of any speed grade have an INIC a SpyNIC for MOST and a StressNIC for MOST on board The accuracy of INIC MOST time stamps is 500 us When analyzing data e g when interpreting an acknowledged code it is important to know how the chips INIC SpyNIC for MOST StressNIC for MOST are arranged inside the OptoLyzer MOCCA compact OptoLyzer MOCCA compact Figure 4 2 Order of Chips inside the OptoLyzer MOCCA compact The MOST feature is optional for OptoLyzer MOCCA compact platforms e there are OptoLyzer MOCCA compact platforms supporting MOST50 or MOST150 or without MOST j MOST 50 Data exchange between the OptoLyzer MOCCA
15. e ERONDA 14 4 3 4 4 StressNIC for MOST iia 14 o nn ne ee ea erde pee ee Pees Ama 15 4 3 6 Sleep Mode nase oes ne ds eee oe ee bee Leese ee ee ee ee dee ee ee ee ee ae 15 Chapter 5 Hardware Description eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee 16 5 1 Front Panel sir Ad gu ee ee ghd ceded ea ha chee een en er Hair bed 16 5 2 Rear Patel vun cowed ern ee ae Done De ner E E ei oan ees 19 Chapter 6 Pin Assignment of the Connectors eeeeeeeeeeeeeeeeeeeeeeeeeeee 21 6 1 HON peca CAN sore Saar paa oat ee cee Keen De d Thig ie S r d Pease Ges eee 21 6 2 LIN Fl xRaAY six aan ae eee hend eher ee nee re 22 6 3 LIN Low Speed CAN and Single Wire CAN 2 6 o oocococoonono een en 23 6 4 Synchronization and Power Lee ee ee ee nennen een een 23 6 5 Digital Audio In Out S PDIF 0 0 0 0 0 ee eis ee ee ee ee eee ees 24 6 6 Analog Audio In Out 0 0 6 ee eee eee eens 24 6 7 USB erori armas pe eae ee an oe fe ose ed Geen mm mam e aes ees 24 6 8 ROI cu anord ar whe dos E we mun dh ed wea ees ohn eee ae eee ee eens ee eee eee 25 6 9 BC cea eee aes oie eee Pees decease eee aoe eee ee beeen epee edad 25 6 10 MOST CORNCCION u au usa hb bce ded nn hr air HC AGE Sede add ORE eS Eee ES 26 BIO 1 O ST 22442 rescato rra aa re ew aes be eee bees eee ees 26 6 10 2 MOST150 ui c eee eee teeta 26 Revision 1 0 04 29 13 2 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 7 Tech
16. e oo st Sh ree ae ae ae da ee eee eae ae 6 1 3 Definitions of Terms o moss raras ensure rennen T 1 4 FREICTONCCS eS 8 Chapter2 Safety Instructions soco cotos 6s ai ii ae 9 2 1 Supply and Synchronization a na aaa ee ee een een 9 2 2 CIA eigin a da ag ce cate eE er er ee ee ae dec wed ee a ne wee wed mh si 9 Chapter 3 Definitions Limit Class ooooooooooooocoooc rocoso 10 3 1 ALS 0 y nen aoa Gran agh eens oe aoe er We a ee ears ea oo Sn ar de ah aoin ie gig 10 Chapters INtOdUCHON are aa een AB airis go 11 4 1 Feature Summary ee ee ee ee ee ee se se ee ee ee ee ee ee eee ee ee ee ee eis 11 4 2 BIOCK DIAGO aan ee ones ana near Eee di does een wad e 12 4 3 Properties of Embedded Bus Systems i e ee ee ee ee ee ee ee ee ee ee ee eis 12 dol CAIN en ee a heed re mm reir de e ae eee nee ee 12 4 3 1 1 High Speed Transceiver 222022400200000n0nnnnnnnnnn nano nnnn nenn nun nano nano nenn nenne nano name nennen 12 4 3 1 2 Low Speed Transceiver nnuuesssenssennnonnnnnnnnonnnennnnnnnnnnnnennnnnnnnnnnnennnennnn nenne nnnennnnnnnnnn 12 4 3 1 3 Single Wire Transceiver uususuasssannnonnnnnnnnnnnnnnnnennnnnnnnonnnennnn nenne nano nnne neue nenne nnne nennen 13 A ds coc ae ne ne cannes ne ee pe ae a Bde Rewe ner ee 13 ASS ARA 13 Moe MOO osado nee a ae er een ee ee 14 SAT MIST ee ae ee ee nenne 14 3A 2 NOS I ee ee ee een ne ee ee ee 14 4 3 4 9 SPYNIC Tor MOST u0445s04 04n004n000 BAAR nannten hen n
17. e required to take adequate measures Revision 1 0 04 29 13 10 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 4 Introduction The OptoLyzer MOCCA compact is an out of the box automotive bus interface combining most of the current automotive field buses The device can be used e g as an automotive bus interface featuring simulation via PC or as an analyzing device for the different automotive bus networks Due to its PC compatible connections including USB 2 0 and 10 100 Mbit s Ethernet it is easily possible to control the embedded OptoLyzer MOCCA compact software from the PC including monitoring tracing and logging of data exchange over the different field bus systems On MOST the OptoLyzer MOCCA compact provides comfortable spy and stress functionalities The OptoLyzer MOCCA compact is available in different hardware platforms optimized for dedicated use cases e g with or without MOST connector different MOST speed grades 4 1 Feature Summary The following list covers the key features of the hardware platform Some of the options may not be available in specific configurations 6 high speed CAN buses two of them selectable either as high or low speed transceiver or single wire CAN 1 FlexRay bus 6 LIN buses m MOST150 MOST5O0 or without MOST USB 2 0 port supporting high speed with 480 Mbit s and full speed with 12 Mbit s Ethernet connection with 10 100 Mbit
18. ed authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage Any and all such uses without prior written approval of an officer of K2L will be fully at your own risk The K2L logo is a trademark of K2L Other names mentioned may be trademarks of their respective holders K2L disclaims and excludes any and all warranties including without limitation any and all implied warranties of merchantability fitness for a particular purpose title and against infringement and the like and any and all warranties arising from any course of dealing or usage of trade In no event shall K2L be liable for any direct incidental indirect special punitive or consequential damages or for lost data profits savings or revenues of any kind regardless of the form of action whether based on contract tort negligence of K2L or others strict liability breach of warranty or otherwise whether or not any remedy of buyer is held to have failed of its essential purpose and whether or not K2L has been advised of the possibility of such damages K2L OptoLyzer MOCCA compact V3 1 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table of Contents Chapter Prine ss riores en a Ch dh gh ah i ae een 6 1 1 Intended Use vu u dwanec warn Blas ale dde oe ee ee ee ee se ed ee hw Odd a ee ee ee ee 6 1 2 Scope of Delivery 20 4 2 548 cav
19. nal S PDIF source routed to the MOST network The S PDIF IN is routed through a sample rate converter The signal can be either a mono or stereo signal OO O N oO MOST Supported Framerates 8 bit channel 8 bit channel 16 bit channel 16 bit channel 32 96 kHz 24 bit channel 24 bit channel Direction MOST to S PDIF OUT S PDIF data from the MOST network routed to an external S PDIF sink The signal can be either a mono or stereo signal Revision 1 0 04 29 13 20 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter6 Pin Assignment of the Connectors 6 1 High Speed CAN Connector type for both High Speed CAN connectors DE 9 Figure 6 1 shows the connector pin assignment as it is visible on the rear panel 00000 0000 Figure 6 1 DE 9 Connector The provided GND pins must not be used unless there is no other GND connection These pins must not be used for supply purpose Table 6 1 Pin Assignment of Connector High Speed CAN 1 3 5 IN IN ern CSC ECC ee Tan ern I ECC O es O cmd Os Tonne Os IE III IN 1 Ot re The provided GND pins must not be used unless there is no other GND connection These pins must not be used for supply purpose K2L OptoLyzer MOCCA compact V3 1 21 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Table 6 2 Pin Assignment of Connector High Speed CAN 2 4 6 SIGNAL DESCRIPTION i a 3
20. nical Specifications ooooooooooooococr roo r roo ros 27 Chapters Revision History 2 42 22 ea aa km 29 K2L OptoLyzer MOCCA compact V3 1 3 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual List of Figures Figure 4 1 Block Diagram 2 00 nennen een ernennen 12 Figure 4 2 Order of Chips inside the OptoLyzer MOCCA compact 0 00000 e eee 14 Figure df Fon Panel E G kerora UU a a re Be a mw Ara En ae 16 Figure 5 2 Rear Panel E G with S PDIF Interfaces 2222 on oeuee eee eee 19 Fig re 6 1 DE 9 Connector ss cca e Rn ar a en ea dd a Dane 21 Figure 6 2 Pin Assignment of the Sync and Power Connector 0 00 ccc eee nenn 23 Figure 6 3 Pin Assignment of the S PDIF Connector even ee eee 24 Figure 6 4 Pin Assignment of the Analog Audio In Out Connector 00 0000 ee 24 Figure 6 5 PIN Assignment of the MOST50 Connector o oococoonoco nenn 26 Revision 1 0 04 29 13 4 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual List of Tables Table 1 1 Definitions of TermS 2 nananana anaana ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee T Table 5 1 Connectors on the Front Panel ee ee ee ee ee ee eee ee ee 17 HE sisi Et re oe da ais en aria ee ee ee ee rn 18 Table 5 3 Connectors on the Rear Panel o ooooooror nen 19 Table 6 1 Pin Assignment of Connector High Speed CAN 1 3 5
21. nt of the MOST50 Connector PIN NUMBER DESCRIPTION 1 4 5 8 Not connected ETXN ERXN ERXP 6 10 2 MOST150 Connector type Tyco Micro FOT 2 0 The orientation of the Rx and Tx path is printed on the panel The MOST150 connector is designated for a 2 0 optical header cable The direction is visible on the cable a Tx Optical output for MOST network Rx Optical input for MOST network Revision 1 0 04 29 13 26 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual Chapter 7 Technical Specifications The table below covers characteristics of the OptoLyzer MOCCA compact and its bus interfaces Table 7 1 Device and Bus Characteristics PARAMETER VALUE 512 kB external 240 kB internal Flash Memory 2 MB internal Controllers Controller Renesas V850E2 FL4 h 160 MHz CAN Transceivers Low Speed CAN Transceiver NXP TJA 1054 most cats ye a MOST Controllers S PDIF I O electrical via 2 x cinch input sample rate 32 96 kHz USB Cypress EZ USB 2 0 The table below covers mechanical characteristics of the OptoLyzer MOCCA compact Table 7 2 Mechanical Characteristics PARAMETER VALUE UNIT Dimensions H x W x D EA Ambient Temperature Range 40 70 INN K2L OptoLyzer MOCCA compact V3 1 27 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual The table below covers electrical characteristics of the OptoLyzer MOCCA compact Table 7 3 Ele
22. s a S PDIF coaxial input and output for audio streaming over MOST Analog audio input and output for audio streaming over MOST MOST ECL support or generic trigger in output Relay to switch external loads of up to 5 A Time stamp synchronisation with cascaded OptoLyzer MOCCA compact devices over power cables a SpyNIC for MOST on board a StressNIC for MOST on board K2L OptoLyzer MOCCA compact V3 1 11 Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 4 2 Block Diagram A block diagram shows the features available for the OptoLyzer MOCCA compact V3 1 In order to minimize crossing lines the FPGA was split in two blocks 4x CAN High Speed High Speed or 2x CAN Low Speed or Single Wire CAN l 6x LIN Flash mm 5A y ie La 5 FlexRay Debug amp IC IN Flash RAM 2S OUT Analog 240 kByte IN 32 96 kHz OUT 10 100 BASE TX RAM S PDIF 512 kByte USB 2 0 M ST 3 6 Pin a 12S MediaLB Figure 4 1 Block Diagram 4 3 Properties of Embedded Bus Systems The OptoLyzer MOCCA compact is intended to be used as stimulation test and analysis device for automotive field buses with DUTs connected to them Therefore the design is constrained to ensure the behavior to be as passive as possible 4 3 1 CAN The accuracy of CAN time stamps is 500 us 4 3 1 1 High Speed Transceiver High speed CAN bus systems according to ISO 11898 2
23. ts e g ATS OptoLyzer MOCCA compact bundle inclusive OptoLyzer Suite support for MOST50 and MOST150 The delivery covers the following OptoLyzer MOCCA compact Power cable MOST cable USB cable USB stick license dongle CAN termination resistors optional Sync and power cable optional Adaptation Kit optional Check your shipment for completeness If you have any complaints direct them to sales K2L com Providing the delivery note number eases the handling Revision 1 0 04 29 13 6 K2L OptoLyzer MOCCA compact V3 1 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 1 3 Definitions of Terms For better understanding of the following chapters this section provides explanation to special terms used in the description of the OptoLyzer MOCCA compact user manual Table 1 1 Definitions of Terms ATS Automotive Test System Test Automotive Test System O EEE CI 1 o o pMoste Media Media Oriented Systems Transport Media Oriented Systems Transport Transport ee introduced from Radio Corporation of America K2L OptoLyzer MOCCA compact V3 1 T Revision 1 0 04 29 13 K2L USER MANUAL OptoLyzer MOCCA compact User Manual 14 References 1 Electrical Physical Layer Specification Version 2 0 Refer to FlexRay Consortium 2 International Organization for Standardization http www iso org 3 Telecommunications Industry Association http www tiaonline org 4 International Electrotechnic
Download Pdf Manuals
Related Search