User manual uniCFUGE 5 - Master Englisch - LLG
Contents
1. can lead to serious internal material damage Ensure to check rotor for any signs of damage before use Rotor amp rotor lid showing visible signs of corrosion or mechanical damage should not be used e Do not fill tubes while they are in the rotor Liquid spillage may harm the device e For safety we have provided protective earthing with power supply Make sure power supply is earthened e n the event of contamination caused by aggressive agents the rotor must be cleaned immediately using a natural cleaning liquid This is particularly important for the bores of the tubes If any damage is seen contact the service technician e Before using cleaning or decontamination methods other than those stipulates by the manufacturer contact the manufacturer to ensure that the intended method will not damage the centrifuge e The power adaptor given with centrifuge unit is designed to use for that particular centrifuge Do not use any other power adaptor 3 INSTALLATION The table top genius is supplied in a box Open the box then remove the packaging and gently take out the centrifuge from small box Before 1 time usage open the centrifuge amp ensure to remove all packaging from the rotor chamber The user manual and accessories should be kept with the centrifuge Please keep all packaging in safe storage for at least 2 years for warranty purposes 3 1 LOCATION Place the centrifuge on a flat and leveled surface ensure that the fo2. hazardous or flammable environment and must not be used to centrifuge explosive or highly reactive substances Also do not place the potential hazardous material within the clearance area envelope e f liquids are spilled on the rotor or rotor chamber the centrifuge must be cleaned carefully and properly before being used again e Prior to centrifugation the tubes should be visually inspected for material damage Damaged tubes may not be centrifuged This is because broken tubes can in addition to sample loss create imbalance which can result in further damage to the centrifuge and accessories e The capacity of 12 x 2 ml must not be exceeded as it is the maximum capacity Do not use liquid with density higher than 1 2g ml for full load operation 2 SAFETY PRECAUTIONS e Do not lean on the equipment It may damage the equipment or the harm the operator e When moving the centrifuge from a cold room to a normal room run the centrifuge for 30 minutes beforehand in the cold room to avoid condensation Alternately allow it to warm up in lab for at least three hours but do not plug in the centrifuge in order to prevent possible damage by condensation e Be sure to close the tubes lid tightly prior to centrifugation Open tubes lid can be torn off during centrifugation and can damage the rotor lid or centrifuge e Rotors and rotor lids are high graded components which are subject to extreme mechanical strain Even slight scratches and tears
3. IME TEXT BOX will disable as this timer will convert to count up timer Press STOP OPEN BUTTON to stop short spin operation 24 8 REMOTE OPERATION amp PROGRAMMING 3 4 10 CENTRIFUGE LID STATUS The above images will be display in the screen according to the status of lid This will be the indication to the user regarding lid status 3 4 11 CENTRIFUGE STATUS This symbol shows the centrifuge status When centrifuge is running the symbol rotates and when centrifuge is not running the symbol will be stable NOTE Centrifuge will get connected to computer only if USB cord is connected to both centrifuge and computer Proper selection of centrifuge COM PORT is necessary to enable the remote operation It is highly recommended not to use or work on any other application or do online work while GUI is operating 25 8 REMOTE OPERATION amp PROGRAMMING 8 4 DATA LOGGER The remote operation comes with data logger features All operations performed through the GUI will be saved in a excel sheet With the help of data logger user can view and take a print out of previously performed operations User can access the data logger file from the desktop Data logger file named as Centrifuge Data Logger will generate automatically on desktop of user s computer once operation is performed The following type of operation details will saved in an excel sheet The following type of operation details will saved in an excel sh
4. N the ongoing operation from the unit 8 4 UNDERSTANDING THE GUI AND OPERATION After installing the GUI software open GUI software by double clicking the software icon The following GUI window will open on computer screen GUI SCREEN Shows Connection Status Shows Centrifuge Lid Status Shows Centrifuge Details Program Setting amp Selection Operation Status Indicator Program of99 gt SPEED RPM MIN SEC RPM ie 0 o ee Min Sec Operating Panel Date Friday 27 September 2013 Shows Current Date amp Time Ti 2 22 38 PM j _ Sample Number amp Note Details 19 8 REMOTE OPERATION amp PROGRAMMING 8 4 1 COM PORT CONNECTING AND DISCONNECTING UP DOWN BOX TEXT BOX COM2U BUTTONS COM2O Centrifuge Connected Once you connect the USB cable the COM PORT for the centrifuge is detected automatically Now click on the CONNECT button to connect shaker and computer for remote operation After connection the TEXT BOX will show COM M12P Connected and the following change of diagram will appear in GUI screen gt Ht wae NIRIER ya Ir ne Disconnected Connected NOTE Once the software is connected the buttons on the centrifuge are deactivated amp only stop button will operate 8 4 2 CENTRIFUGE DETAILS ID AB1309AA0001 Version G1 2 D1 2 Operation No 0 After centrifuge connection the centrifuge ID and vers
5. THE ROTOR 1 Always balance the rotor before centrifugation Following are symmetrical loading of centrifuge tubes to rotor 2 The above is the correct method of loading the tubes in the rotor The samples in the tubes should be of equal volume 3 Symmetrical loading of tubes in the rotor is necessary Otherwise vibration or imbalance can occur which can cause serious damage to the centrifuge 4 If the tubes are not loaded symmetrically then the imbalance detector will cut off the running centrifuge for device amp user safety This will stop the centrifuge and Err 55 will be seen indicating tubes are not loaded symmetrically To resume operation load tubes symmetrically amp restart the centrifuge 5 Incorrect method of loading tubes in centrifuge rotor NOTE ncorrect method of loading tubes can lead to an accident 13 7 OPERATING THE CENTRIFUGE 7 1 SWITCH ON THE CENTRIFUGE Switch ON After connecting the power adaptor switch ON the power mains amp the switch at the rear side of the centrifuge Make sure to check the rotor fitment before use Centrifuge will not operate with open lid NOTE Maintain a gap of 3 seconds between switch OFF and switch ON again DO NOT switch OFF and ON again instantly 7 2 SETTING SPEED AND TIME After closing the centrifuge lid press SPEED BUTTON to select speed setting Now rotate the SETTING KNOB clockwise to increase the speed value and rotate
6. Te LABWARE Operating Manual Centrifuge uniCFUGE 5 CONTENTS 1 Product Descriptio ne een 1 1 1 Introduction 1 2 Intended Use 1 3 Salient Features 1 4 Standard Accessories 1 5 Technical Specification 2 Safety PrecautioNs en ee 4 3 IVS CAN ALONG ee a n 3 1 Location 3 2 Connecting Power Adaptor 4 Standard Parts Listing 2224s020222202000000000nenenennnennnn nenne nnnnnnn nennen 7 5 User Interface and Display 22us020222202000000nnenenennnnnnn nenne nennennnnennnn 8 6 Rotor Installation een 10 6 1 Rotors and Accessories 6 2 Rotor Removing amp Replacing Process 6 3 Balancing the rotor 7 Operating the Centritupfe u nnninienernne 13 7 1 Switch ON the centrifuge 7 2 Setting Speed and Time 7 3 Switching to RCF Display 7 4 Short Spin Centrifugation 7 5 Opening Centrifuge Lid in Power Failure 7 6 Imbalance indicator 8 Remote Operation amp ProgrammMing cccccccccccccceccsccssecssecsceseeeseeees 17 8 1 System Requirement 8 2 Installing GUI software 8 3 Connecting USB cable 8 4 Understanding the GUI and its Operation 8 5 Data Logger 9 Maintenance and Cleaning cccscscccescsssseceecessseecesceceeecesenceseeeeauees 26 10 Tro bleshooting nee 27 11 Ordering INFOrMALtION cc cc ccsesssteceecessseseeceecessnsaeseeceeceeaeceeeeceneness 29 12 Warranty StateMentt cccccseccsecsessssssssseesceeceeceecseassaeceeceeceec
7. Variable 500 15000 rpm Speed Accuracy 100 rpm Maximum Volume 12 x 2 ml microtubes Maximum RCF 15596 xg Ambient Temperature 5 40 degree C Permissible Relative Moisture lt 80 Acceleration Time 20 2 seconds Deceleration Time 28 2 seconds Noise Level lt 62 dB Size L x B x H 262 x 230 x 131 mm Weight 4 04 Kg with rotor Input Power 110 240 VAC 50 60 Hz Output Power 24VDC 6A Rated input of Adaptor 3A Power Requirement 2 SAFETY PRECAUTIONS e Never use the centrifuge in any manner not specified in this manual e Equipment used in any manner not specified in this manual or by the manufacturer the protection provided by the equipment may be impaired e Never move the centrifuge while the rotor is spinning e The rotor and the rotor lid must always be securely fastened If the centrifuge makes unusual noise during operation the rotor or rotor lid fitment needs to be checked Switch OFF the device immediately by pressing STOP check fitment amp fasten it well e The rotors must be loaded symmetrically Each tube should be counter balanced by another tube of same weight e Do not use centrifuge or rotor that have not been correctly installed or damaged e Repairs must only be performed by authorized service technician e Only use recommended original rotors and spare parts for best result amp product safety e Centrifuge may be used for the specified applications only It must not be operated in a
8. and not its repair For repair please contact the supplier For your reference make a note of the serial number date of purchase and supplier here Serial No Purchase Date Supplier 1 PRODUCT DESCRIPTION 1 3 SALIENT FEATURES Centrifuge has following features 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Imbalance detector with auto cutoff Large back light digital LCD display High centrifugal force which delivers 15000 RPM 15596 x g RCF USB port for remote terminal control capability Remote operation with data logger Lid safety interlock amp auto lid open Convenient and easy user interface Quick acceleration and deceleration time One touch short spin centrifugation Last run memory feature Emergency lid release during power cutoff Countdown timer Automatic internal diagnosis amp error display Speed setting by RPM RCF mode Fully autoclaveable high strength aluminum rotor with metal lid Small footprint 1 4 STANDARD ACCESSORIES o gt OF a gS oe ee gt Power supply Adaptor amp USB cable 12 slots microtube rotor Pre installed T Allen wrench Adaptors for 0 4 0 5 ml tubes set of 12 Adaptors for 0 2 ml tubes set of 12 Software CD Product user manual amp warranty guide 1 PRODUCT DESCRIPTION 1 5 TECHNICAL SPECIFICATIONS Motor Type Brushless DC Motor Maximum Speed 15000 rpm Run Time 30 sec to 999 mins amp infinite mode Speed Setting
9. anti clockwise to decrease the speed value The minimum and maximum speed of the centrifuge is 500 rom and 15000 rpm respectively You can speed up the speed value by rotating setting knob quickly 1 Pressing the speed button ONCE will make the speed change in interval of 1000s For example if speed is 10000 rpm then next speed will be 11000 rpm 14 7 OPERATING THE CENTRIFUGE 2 Pressing the speed button TWICE will make the speed change in interval of 100s For example if speed is 10000 rpm then next speed will be 10100 rpm 3 Pressing the speed button more than 2 times will again start the process from point 1 4 The input will be accepted if we leave the setting knob idle for 3 seconds The value will blink five times to indicate acceptance The speed can be changed while the centrifuge is running Press the speed button amp follow above steps Changing the speed between the ongoing centrifugation will run the centrifuge at updated speed for the rest of time as indicated by the timer Press TIME BUTTON to select time setting Now rotate the SETTING KNOB clockwise to increase the time and rotate anti clockwise to decrease the speed The centrifuge timer set for run between 30 seconds to 999 minutes or operated in infinite time mode Infinite timer will be indicated by 4 30 in display The minimum time setting is 30 seconds The timer in the centrifuge is countdown timer and time in the display will be i
10. ation will always start from the 1st line After changing speed and time for centrifugation according to user requirement click on SAVE button to save set the program Follow the same procedure for other lines of the program as needed 8 4 4 PROGRAM NOTE AND SAMPLE NUMBERS User can write the details of each sample used for centrifugation for their reference User can also write General Note regarding the sample used operation details or any other specific information which is worth mentioning according to user in General Note TEXT BOX as shown in below diagram The data entered here would be saved in the data logger report Sample Numbers Details 202 105 mm 0598 1235 11 ave Program General Note 5 6 11 12 has sample Number 3205 Click on the CLEAR BUTTON to clear the sample number and general note details of the program 22 8 REMOTE OPERATION amp PROGRAMMING 8 4 5 PRE SET PROGRAM SELECTION AND OPERATION Click on the PROGRAM SCROLL BUTTON to select the required pre set program out START After selecting required program click on START BUTTON to start the operation of total 99 programs Operation will start from 1st line of selected program There is a delay or pause of 8 seconds between all 4 lines Once operation of 1st line is over it will wait for 8 seconds to start the 2nd line operation During the operation all the buttons on the device and boxes of the GUI will be disa
11. bled except STOP OPEN button When the ap centrifuge is running the symbol in the GUI will rotate NOTE There is delay or pause of 8 seconds between all 4 lines 8 4 6 STOP OPERATION STOP OPEN Click on STOP OPEN BUTTON to stop the ongoing operation Centrifuge lid opens automatically when the rotor comes to standstill User can also stop the ongoing Operation by pressing STOP OPEN button in device The lid status will be indicated on the GUI screen 23 8 REMOTE OPERATION amp PROGRAMMING 3 4 7 ACTIVE LINE SPEED DISPLAY RPM TEN This SPEED UP DOWN BOX is used to read speed value of active line of the program For example if line 3 of 46th program is running then this SPEED UP DOWN BOX will display the speed value of line 3 of 46th program It can be used to change the speed value of active line Click on RPM or RCF BUTTON to read speed value in RPM or RCF mode for active line 3 4 8 ACTIVE LINE TIME DISPLAY TIME TEXT BOX is used to read remaining time value of active line of the program For example if line 3 of 46th program is running then this TIME TEXT BOX will display the remaining time value of line 3 of 46th program This is countdown timer 3 4 9 SHORT SPIN CENTRIFUGATION Short ish sa After setting required speed in SPEED UP DOWN BOX click the SHORT SPIN BUTTON for short spin operation The timer value in this mode is incremental in seconds During short spin operation this T
12. ct fails within the specified period of time because of a defect in material or workmanship contact LLG The software is made available with the centrifuge kit It is designed to work on Windows XP SP3 Windows 7 The software should be used as explained in the user manual The warranty does not cover the software failures due to issues in user system computer or laptop Products received without proper authorization will not be entertained All items returned for service should be sent postage prepaid in the original packaging or other suitable carton padded to avoid damage LLG will not be responsible 31 12 WARRANTY STATEMENT for damage incurred by improper packaging LLG may elect for onsite service for large equipment Some states do not allow limitation on the length of implied warranties or the exclusion or limitation of incidental or consequential damages The purchaser agrees that there is no warranty of merchantability or of fitness for any intended purpose and that there are no other remedies or warranties expressed or implied which extend beyond the description on the face of the agreement This warranty is only applicable to the original purchaser No individual may accept for or on behalf of us any other obligation of liability or extend the period of this warranty This warranty is valid only if the warranty is registered with the supplier within 30 days from the date of purchase The purchaser agrees
13. d be avoided Liquid should not come into contact with the motor 6 After cleaning ensure that all parts are dried 7 Regularly cleaning of the rotor is important 8 If the rotor chamber needs cleaning clean with cloth or sponge moistened with a neutral detergent solution 9 Do not place the rotor into the cleaning solution 10 If corrosive toxic or pathogenic bacteria are accidentally spilled in the rotor or rotor chamber the centrifuge must be decontaminated thoroughly 27 10 TROUBLESHOOTING This centrifuge has a self diagnostic function If a problem occurs an error warning code will be displayed on the display screen and the operator can determine the malfunction with the warning code below ERROR PROBLEM SOLUTION No display No main power Power check amp proper plug connection in of mains cable at both ends Check the mains fuse of the lab Improper connection Connect adaptor properly Lid not closed correctly Close lid correctly Error with lid closing and Contact service opening mechanism Rotor not loaded Load rotor symmetrically amp symmetrically restart centrifuge cannot be opened a stop Power failure Emergency lid release after rotor stops Centrifuge shakes Rotor not loaded Load rotor symmetrically amp during acceleration symmetrically restart operation amp Exceptional running noise Either a broken tube Replace broken tube For damage to the rotor or damaged roto
14. e imbalance operate the centrifuge The imbalance detection feature cannot be deactivated as it is factory fitted 17 8 REMOTE OPERATION amp PROGRAMING For programming and remote operation the centrifuge needs to be connected to a computer 8 1 SYSTEM REQUIREMENT The GUI software and data logger file required the following minimum system requirement to operate Operation System Windows 7 with i3 Processor or more having 32 bit or 64 bit operating system and Windows XP SP3 Microsoft NET framework 4 and Microsoft Office Excel 2007 or 2010 is required for operating GUI 8 2 INSTALLING GUI SOFTWARE Software CD is provided with the centrifuge kit Install the software from the CD by running the setup file After installation the GUI software icon and centrifuge data logger file will appear on the desktop 8 3 CONNECTING USB CABLE Connect one side of USB cable to back side of centrifuge and another side to computer USB port Without USB connection the centrifuge will not operate through software USB connection is shown below 18 8 REMOTE OPERATION amp PROGRAMMING After connecting USB display of centrifuge will show the USB connection Top left symbol in centrifuge display indicates USB connection USB CONNECTED HOLH Once the USB cord is connected centrifuge unit controls will be disabled The centrifuge can now be run using the program Only the STOP OPEN BUTTON will work to STOP OPE
15. e g n R N m See T Allen Ke Rotor Nut Max Speed 15000 y Max RCF 13080 6 263 535 Note Rotor and Accessories given recommended by manufactured should be used with the equipment 11 6 ROTOR INSTALLATION 6 2 INSTALLING AND REMOVING ROTOR Upon reception of centrifuge the rotor comes pre installed In case if you want to remove or replace rotor follow the below mentioned procedure 6 2 1 REMOVING ROTOR 1 Do not remove or loosen the rotor lid before attempting to remove rotor Remove rotor together with the lid 2 Using T Allen Key loosen the rotor nut by turning it anti clockwise Do not try to pull the rotor rotor will come up automatically 3 Once the rotor nut is loosen completely pull up rotor and lid vertically 6 2 2 REPLACING ROTOR 1 T Allen Key To Tighten Rotor Lid Nut 2 Rotor Lid 3 4 Note 1 Check the rotor is firmly tightened before running To replace or install the rotor take rotor and load vertically on the motor shaft Place the rotor nut in the center hole of the rotor onto the motor shaft Put T Allen Key in rotor nut amp turn clockwise to tighten and anti clockwise to loosen rotor After properly fastening rotor place rotor lid on the rotor lid nut with hand by rotating rotor lid nut clockwise 2 Do not remove or loosen the rotor lid cap before removing rotor 12 6 ROTOR INSTALLATION 6 3 BALANCING
16. eeceeeeeees 30 13 Product DispoSal ccccssssssecescsssseceeceseseeeceecesesaeecesceeaeeceeeusesseeesanees 32 1 PRODUCT DESCRIPTION 1 1 INTRODUCTION Thank you very much for purchasing LLG uniCFUGE 5 You are using the table top genius high speed micro centrifuge The product is equipped with a maintenance free drive a large display amp a simple interface for silent amp efficient operation for daily lab usage This next generation micro centrifuge can be operated via USB with facility of data logger and comes with a host of safety features including imbalance detection The programmable centrifuge can deliver upto 15000 rpm and can process volumes upto 12 x 2 ml microtubes It can also accept different types of microtubes including 0 2 ml 0 4 ml amp 0 5 ml micotube when used with the reduction adapters supplied along with the unit A separate strip rotor is also available for using 2 x 8 PCR strips 1 2 INTENDED USE Centrifuge is used in various laboratories to separate particles from suspension or even macromolecules from solutions according to their density The different biological substances that are usually separated by centrifugation are microbial cells mammalian cells organelles proteins DNA and RNA It is majorly used in research laboratories NOTE Before using the centrifuge please read this user manual carefully This user manual is intended to assist with the operation and care of the unit only
17. eet A B C D E F G H 7 Date Friday 19 July 2013 8 Time 4 45 25 PM 9 Centrifuge ID AA1307B30001 10 VersionNo 61 2 D1 2 Operation No 1 12 S1 13 S2 14 53 15 54 16 S5 17 S6 18 S7 19 S8 20 S9 21 S10 22 S11 23 512 24 Note NORMAL Operation 26 P 1 27 L 1 28 SET SPEED 15000 RPM 29 SET TIME 2 Min And 51 Sec m un 31 STOP TIME 2 Min And 27 Sec 32 Run TIME 0 Hour And 0 Min And 24 Sec ERROR STATUS 4 gt Centrifuge Data L er Sheet2 Sheet3 ww W NOTE The GUI software will not operate if Centrifuge_Data_Logger file is open Ensure to close the log sheet before remote operation 26 9 MAINTENANCE AND CLEANING 1 The rotor and the outside of the centrifuge should be cleaned regularly with a moist cloth 2 Ensure that while cleaning the unit is not plugged in 3 Wear protective gloves amp safety glass while operating amp cleaning the device 4 The brushless motor in the centrifuge requires no routine maintenance Any required service should be performed by authorized qualified personnel only Repairs performed by unauthorized personnel may void the warranty 5 Always keep the centrifuge housing rotor chamber rotor and rotor accessories clean All parts should be wiped down periodically with a soft cloth For more thorough cleaning use a neutral cleaning agent Ph between 6 and 8 applied with a soft cloth Excessive amounts of liquid shoul
18. et speed and time values Rotate the knob 4 clockwise to increase and anti clockwise to KNOB decrease values 5 START Press button to START running centrifuge l BUTTON RPM RCF e BUTTON Use to set read RPM RCF values J SHORT SPIN Press amp hold button after setting the required l BUTTON speed to run centrifuge for short time 5 USER INTERFACE AND DISPLAY 6 7 1 2 Min Sec RPM RCF Min Sec Description Indicates centrifuge status When centrifuge is running the symbol rotates and when centrifuge is not running the symbol is stable Indicates the speed value at which centrifuge is running x g indicates the value in RCF mode The timer is a countdown timer Indicates the time for which the centrifuge will run Indicates the time in Min Sec mode Indicate RPM or RCF mode and shows corresponding values Centrifuge is connected via software When this mode is active control panel buttons except stop button will be deactivated 10 6 ROTOR INSTALLATION 6 1 ROTORS AND ACCESSORIES uniCFUGE 5 could accommodates 2 types of rotors amp comes with 2 types of reduction adaptors Below is the chart detailing Maximum RCF of rotors amp reduction adaptors 12 tubes rotor 1 5 2 0ml tubes 0 5ml 0 4ml tubes 0 2ml tubes Max Speed 15000 15000 15000 15000 Max RCF 15596 12577 12074 10816 PCR Strip Rotor 0 2ml PCR Strip For PCR Optional rotor ET OS CES Ba N N Nas aer a iy 4 IN ea
19. fuge is 15596 x g The system will automatically convert the values from RPM to RCF and vice versa 7 4 SHORT SPIN CENTRIFUGATION Press SHORT SPIN BUTTON Short Spin Centrifugation is the feature for short pulse run It will run as long as the button is pressed Set rotational speed prior to short spin as required During short spin the timer will be in incremental mode After releasing short spin button the time in the display will show duration of short spin 7 5 OPENING CENTRIFUGE LID IN POWER FAILURE Disconnect the centrifuge from the main supply Wait until the rotor has come to a standstill this may take longer time Over the rotor has stopped lift up the centrifuge and pull out the emergency lid release cap This will open the centrifuge lid After the centrifuge lid opens push the thread back in the hole with hand and fit the emergency release cap back in the hole 16 7 OPERATING THE CENTRIFUGE Release pin J 7 6 IMBALANCE INDICATIOR The centrifuge is equipped with an imbalance detection safety feature When the rotor is not loaded symmetrically the imbalance detector gets activated and will cut off the centrifugation The error Err 55 will be shown on the display To bring back the centrifuge to normal condition switch OFF and switch it ON Then open the centrifuge lid and correct the imbalance load using method described in the balancing the rotor section page no 13 of this manual After correcting th
20. g de Distributed By 34
21. ion will display in the GUI screen The operation number shows the number of operation performed using the software 20 8 REMOTE OPERATION amp PROGRAMMING 8 4 3 SETTING A PROGRAM Remote operation provides centrifugation with 99 programs and each of maximum 4 lines It can be used to pre set program for specific regular operations User can save upto 99 programs according to their needs The same can be used for the cases mentioned below 1 Run centrifuge for 2 minutes and 7 seconds with speed 15000 RPM 2 Then take a pause of 30 seconds 3 Then run centrifuge for 3 minutes and 22 seconds with speed of 7500 RPM 4 Then take a pause of 4 minutes and 15 seconds PROGRAM Program d SCROLL BUTTON SPEED TIME UP DOWN Line 1 UP DOWN BUTTONS BUTTONS Line 2 Line 3 Line 4 SAVE BUTTON Note There is delay of 8 seconds between all 4 lines After filling at least one program line the centrifuge display will change as shown below ATLEAST 1 PROGRAM LINE FILLED 21 8 REMOTE OPERATION amp PROGRAMMING Click on the PROGRAM SCROLL BUTTON to select the required program out of total 99 programs you wish to set User can save up to 99 programs Start with the 1st line click on the SPEED UP DOWN BUTTON to select value of the specific line of the program Speed can be set only in RPM mode Same way click on TIME UP DOWN BUTTON to select time value of specific line of the program Up to 4 lines of a program can be saved Oper
22. n Min Sec mode The same will showed on the display 1 Pressing the time button ONCE will make the time change in interval of minutes For example if time is 005 00 5 Mins O Sec then next time will be 006 00 6 Mins O Sec 2 Pressing the time button TWICE will make the time change in interval of seconds For example if time is 005 00 5 Mins O Sec then next time will be 005 01 5 Mins 1 Sec 3 Pressing time button more than 2 times will start the process from point 1 4 The input will be accepted if we leave the setting knob idle for 3 seconds The value will blink five times to indicate acceptance 15 7 OPERATING THE CENTRIFUGE Press START BUTTON to start operation and press STOP OPEN BUTTON to stop a the ongoing operation When the centrifuge is running the symbol amp Y will be rotating Pressing the STOP OPEN BUTTON will stop the operation as well as it will open the centrifuge lid automatically once the rotor comes to a stop If the time gets over the centrifuge will stop and lid will automatically open When the a7 centrifuge is not running the symbol CY will be stable To open the lid without a run press the stop open button 7 3 SWITCHING TO RCF DISPLAY Press RPM RCF BUTTON to change the mode from RPM to RCF Relative centrifugal force After pressing the button the display will show the speed in RCF Maximum RCF speed of the centri
23. r motor motor is cause for run contact service noise representative Rotor damaged Remove amp change rotor Display error Loose connection of Contact service display representative 28 10 TROUBLESHOOTING ERROR PROBLEM SOLUTION Err 1 Lid latch Limit switch is Open lid and close it not pressed properly Power tripping Cable not fit properly Remove cable and connect properly Last run memory not Turing ON centrifuge Keep 3 seconds gap displayed immediately after turning between switch OFF and it OFF switching ON again System gets hang Electronics error Switch off centrifuge and then switch it ON again If the error still shows contact service representative IMPORTANT NOTE 1 If system gets hang or get hot due to over current switch OFF amp switch ON restart the centrifuge and check it again 2 Maintain 3 seconds gap between switch OFF and switch ON Instant ON OFF can lead to a reset erasing last run memory 3 If motor gets hot due to which there will be fluctuation in speed value then allow centrifuge to get cold for atleast 30 minutes Do not do any operation for 30 minutes 4 It is highly recommended not to use or work on any other application or do online work while GUI is operating 5 The GUI Software will not operate if Centrifuge_Data_Logger file is open Close the Centrifuge Data Logger file and open software for remote operation 6 Do not use liquid with density highe
24. r than 1 2g ml for full load operation 29 11 ORDERING INFORMATION Proposed product coding for Centrifuge M12 code code Colour 110V to 230V Power supply for M12P R12 12 slot rotor 2stripsPCRrotor RSR o O RotorNut RNP M12 Allenkey CP adaptors 0 2 0 4ml DI o adaptors 0 4 0 5m D2 Rotor lid metal 12 slot E12 Strip Rotor metallid ESR o Rotor lid plastic 12 slot mp Cable M12 NOTE M12 1112 is the default code for centrifuge 30 12 WARRANTY STATEMENT It warrants that uniCFUGE 5 will be free from defects in material and workmanship for a period of two 2 years from date of purchase LLG sole obligation shall be to repair or replace at its option any product or part thereof that proves defective in material or workmanship within the warranty period provided the purchase notifies LLG of any such defect LLG DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE This warranty is valid only if the product is used for its intended purpose and within the guidelines specified in this instruction manual This warranty does not cover damage caused by accident neglect misuse improper service natural forces or other causes not arising from defects in original material or workmanship This warranty does not cover damage to paint or finish In an unlikely event if this produ
25. that there is no warranty of merchantability or of fitness for any intended purpose and that there are no other remedies or warranties expressed or implied which extend beyond the description on the face of the agreement This warranty is only applicable to the original purchaser No individual may accept for or on behalf of us any other obligation of liability or extend the period of this warranty This warranty is valid only if the warranty is registered with the supplier within 30 days from the date of purchase 32 13 PRODUCT DISPOSAL In case the product is to be disposed of the relevant legal regulations are to be observed Information on the disposal of electrical and electronic devices in the European Community The disposal of electrical devices is regulated within the European Community by national regulations based on EU Directive 2012 19 EU on waste electrical and electronic equipment WEEE According to these regulations any devices supplied after 13 06 05 in the business to business sphere to which this product is assigned may no longer be disposed off in municipal or domestic waste They are marked with the following symbol to indicate this As disposal regulations within the EU may vary from country to country please contact your supplier if necessary 33 Lab Logistics Group GmbH LLG GmbH Am Hambuch 1 D 53340 Meckenheim Tel 49 2225 9211 0 Fax 49 2225 9211 11 RB WR www lig de info ll
26. ur feet of this centrifuge stand in the surface firmly Avoid installing on a slippery surface or surface prone to vibration 1 Ideal ambient temperature is 20 C 5 C avoid placing the centrifuge in direct sunlight 2 Keep clearance of at least 10 cm on both sides and at least 30 cm behind it to guarantee the cooling efficiency 3 Keep away from heat or water to avoid sample temperature issues or centrifuge failures 4 Do not place the centrifuge so that it become difficult to operate the device 3 2 CONNECTING POWER ADAPTOR 1 Connect one side of power adaptor to rear side of centrifuge and other to supply as shown in the figure below 2 Rotate clockwise the adaptor nut to tighten the adaptor with the centrifuge Ensure the power switch is OFF while connecting the power adaptor 4 STANDARD PARTS LISTING Centrifuge Lid Aluminum Lid Lock Pin Protection Lid Rotor Lid Nut Rotor Lid Rotor Display Control Panel USB Port Power Adaptor ON OFF Switch Port Emergency Lid 4 N en Suction Cups 5 USER INTERFACE AND DISPLAY 7 6 4 5 1 2 3 1 STOP OPEN Press button to STOP the ongoing operation Lid l BUTTON opens automatically after rotor comes to a stop gt SPEED Press button to select SPEED mode Then rotate BUTTON SETTING KNOB to set desired run SPEED 3 TIME Press button to select TIME mode Then rotate BUTTON SETTING KNOB to set desired run TIME SETTING Use to s
Download Pdf Manuals
Related Search