3G Fixed Wireless Terminal FCT-355 User Manual
Contents
1. 5 Polarity reversing function and 12 KHz built in optional Definition of DTMF reversing signal Limit of communicating time GSM function of dialing out the prompt voice When not connecting to Telephone Office line GSM will provide the forced dial out function Setup GSM extra dialing local code Setup extra dialing local code to PSTN GSM isn t ready call will be forced to dial out from PSTN Setting of Dialing type Call Transfer PSTN TO GSM GSM TO PSTN GSM call Transfer setting time to PSTN out DTMF definition of reversed signal GSM Frequency bands Dual Band EGSM 900 and DCS 1800 MHz GSM 850 900 1800 1900 MHz optional Specific Call Transfer setting GSM to PSTN Assign mode one stage dialing Free mode two stage dialing PSTN to GSM An Incoming call will be transferred to specify GSM Number Call Transfer Restriction Setting 10 sets Short Code Setting 100 sets GSM Prefix Number Setting 30 sets Support Call ID DTMF Siemens TC 35 GSM Module SIM Card Pin code disable enable 1 2 Main panel and indicators LED and Button Color Status Description Power Red On Indicator for power supply working Network Green Flash Flash per 1 second means connection with network OK M Press this button to enter menu list or back enu to top menu Up Move up the cursor or add number Down Move down the cursor or reduce number Enter Press this button to co2. PSTN line 3 4 Connect the whip antenna and power supply adaptor to ensure voice quality please place the antenna more than 1 5 meter beyond the device 3 5 Turn ON the switch of the device if the SIM card PIN code is disable it needs about 10 to 45 seconds to finish initialization program This time is based on the signal intensity of the location 3 6 If the SIM card PIN code is set Enable when you switch on the device LCD will display Input PIN CODE User should input correct PIN code through telephone otherwise LCD will display SIM PIN ERROR Note If LCD display SIM PIN ERROR user can reboot the device and input PIN code again but the device will lock SIM card when the inputting are incorrect three times If the SIM card is locked please put it inside your mobile phone and input correct PUK code to release it 4 Make a call 4 1 Lift the handset or press Hand Free to dial the number when you hear the dial tone 4 2 Dial a number the device will choose the GSM PSTN routing automatically Least Cost Routing function 4 3 If the number is a block number See section 9 Block number setting LCD will display BLOCK NUMBER PLEASE HOOKON and then busy tone will be heard 5 Receive calls 5 1 When the device is under PSTN GSM mode user can receive calls from either PSTN line or GSM mobile 5 2 When a call is incoming the telephone bell will ringing pick up the handset or pres
3. the line is ok Interference 1 Antenna interference Please place the antenna away from the power line and telephone line and telephone as far as possible Antenna power line telephone line can not be bound together to lay out If there is a necessary cross connect please make it to be vertical cross connect There should be no transmission equipment around the equipment to avoid interference between each other 2 Bad connection of crystal connector of telephone straight line and coil line please replace them No display incoming call 1 The incoming call display function of SIM card has not been opened Please contact with SIM card operators to open the function 2 No incoming call display Please change another telephone which possesses DTMF incoming call display function Voice quality bad during calling or echo can be heard 1 Adjusting smaller volume of telephone payphone 2 Try to change a better telephone or handset 3 Weak signal Reference Network indicator flickering fast partly content Only toll free number can be dialed out It is possible the balance money not enough Please charge money for your SIM card One way conversation 1 Failure telephone or payphone Please check your telephone or payphone 2 No metering pulse for payphone Please contact with your provider No ring when calls incoming or can not receive any incoming calls 1 Failure telephone or pay
4. to review all permitted codes 11 4 Press Enter key again to add permitted codes LCD will display ADD PERMIT CODE on the top Pick up the handset input Prefix number For example To add 138 as a permitted number just set 138 When the SIM card of this device received a call from 138xxxxxxxx the device will transfer the call to PSTN line See section 10 5 Set GSM to PSTN transfer 11 5 Repeat press Enter key LCD will display DEL PERMIT CODE on the top Pick up the handset input Prefix number For example if you want to delete 138 just input 138 Input to delete all permitted codes 12 Short code setting Note The maximum number of this setting is 100 groups the maximum length of each group is 16 digitals When you set the short codes you can use Short code to dial out 12 1 Press Menu key when the device is standby 12 2 Press UP DOWN key to choose 7 SHORT CODE 12 3 Press Enter key LCD will display Short Code XX press UP DOWN key to review all short codes 12 4 Press Enter key again to edit short codes LCD will display EDIT CODE XX on the top Pick up the handset input Short Code For example To edit NO 06 13823709455 as a short number press UP DOWN key to choose EDIT CODE 06 set 13823709455 then press Enter key to
5. update So when you want to dial 13823709455 you can just dial O6 12 5 Press UP DOWN key you can set another short code 13 GSM Volume setting There are 5 levels can be adjusted for microphone voice and speaker voice The default setting is Microphone level 3 and Speaker level 3 13 1 Press Menu key when the device is standby 13 2 Press UP DOWN key to choose 8 GSM VOLUME 13 3 Press Enter key LCD will display VOLUME MIC SPK on the top 13 4 Pick up the handset press UP DOWN key to delete previous setting input new value from telephone The first value is for transmission Microphone and the second value is for receiving Speaker The range of inputting value is 1 to 5 13 5 Press Enter key to save and exit 14 Other Parameters setting 14 1 Press Menu key when the device is standby 14 2 Press UP DOWN key to choose 9 SET PARAMETER 14 3 Press Enter key to other set parameters press UP DOWN key to select items 14 4 Conversation Time Out setting 14 4 1 Pick up the handset press UP DOWN key to delete previous setting 14 4 2 Input a new value from 00 to 99 The maximum conversation time is 99 minutes 00 means unlimited conversation time For example If you set the value 05 it means all the conversations are limited in 5 minutes 14 5 GSM code length setting 14 5 1 Pick up the handset press U
6. 0 mA DC input voltage range 7 5V to 10V DC Maximum DC current 700 mA DC7 5V external charge current 15 2 Working environment Working temperature 0 to 45 C Relative humidity 10 to 95 Environment noise lt 60dB A Atmospheric pressure 86 to 106 KPa 15 3 GSM parameters Support HSDPA UMTS EDGE GPRS GSM Triple band HSDPA UMTS 850 1900 2100MHz Quad band EDGE GPRS GSM 850 900 1800 1 900MHz HSDPA downlink 3 6Mbps WCDMA UMTS uplink 384kbps EDGE data 237kbps downlink and 118kbps uplink GPRS data 85 6kbps downlink and 42 8kbps uplink SIM card mode 3 0 V Antenna impedance 50 Ohm 16 Appendix 16 1 Definition of grey cable If you want to connect the grey cable to a 2 wires telephone payphone the correct connection method is shown as follow 4 l 2 4 wires RJ 1 1 2 wires RJ 1 1 16 2 Trouble Shooting Trouble phenomenon Solving Methods 1 SIM card has been locked insert the SIM card into a mobile phone if the card has been locked there will display prompt in the mobile LCD which requires inputting PUK code Input PUK code then input a new PIN code and set the new PIN code as 1234 If the equipment has reciprocal SIM card lock function the PIN code of the SIM card should be opened Or the PIN code of the SIM card should be locked to avoid SIM card being locked After unlocking the SIM card insert the SIM card into the Can not dial number equipment and turn the equipment on 2 Can
7. P DOWN key to delete previous setting 14 5 2 Input a new value from 00 to 15 When the value is less than 3 the GSM calls will be sent out after 6 seconds You can press to send it out immediately Otherwise if the length of GSM numbers equal to this setting value the calls will be sent out after 2 seconds 14 6 Polarity reversal setting 14 6 1 Press UP DOWN key to select Disable or Enable 14 6 2 Press Enter key to save and exit 14 7 GSM if No PSTN setting 14 7 1 Press UP DOWN key to select Disable or Enable When you set Enable if the power supply is broken or if the device is turned off or the GSM part has been get some damage the calls will be allowed to go through PSTN line 14 7 2 Press Enter key to save and exit 14 8 PSTN if No GSM setting 14 8 1 Press UP DOWN key to select Disable or Enable When you set Enable if the PSTN part has been get some damage the calls will be allowed to go through GSM routing 14 8 2 Press Enter key to save and exit 14 9 Default setting Pick up the handset and then input 886432 to reload default setting of the factory mode The detail settings are shown as follow Work Mode GSM PSTN Transfer setting Disable Conversation Time Out 00 GSM Code Length 00 Polarity Reversal Disable GSM if No PSTN Enable PSTN if No GSM Enable 14 10 Convert Code setting IP code setting This con
8. ck codes 10 Call Transfer setting This device can transfer calls either from PSTN line to GSM network or from GSM network to PSTN line 10 1 To set PSTN to GSM transferring 10 2 Press Menu key when the device is standby 10 3 Press UP DOWN key to choose 5 Call Transfer 10 4 Set PSTN to GSM transfer 10 4 1 Press UP DOWN key to choose 1 PSTN TO GSM 10 4 2 Press Enter key user can choose Enable or Disable and Enable Free gt Ifyou select Disable mode the device will not transfer the calls from GSM gt If you select Enable Assign mode when someone call the SIM card number of this device the device will transfer the call to an appointed PSTN number Press Enter key to set this number then press to save and exit gt If you select Enable Free mode when someone calls the SIM card number of this device the device will give a dail tone to prompt caller and let caller to continue inputting destination number For example When you set PSTN TRANSFER TO GSM number 138xxxxxxxx If someone is calling in from PSTN line the call will be transferred to 138xxxxxxxx Note If the GSM mobile phone is rejected receiving the call the call will be returned to the telephone which is connecting the device 10 5 Set GSM to PSTN transfer 10 5 1 Press UP DOWN key to choose 2 GSM TO PSTN 10 5 2 Press Enter key there are 3 modes can be chose
9. devices which can gender interference around the equipment for example television radio computer or magnetic memory media for example compact disk etc Only its own suitable power adapter can be used in the device Any other power adaptors maybe damage this device and this kind of damage is out of the scope of maintenance If it is found that the device is unable to login GSM network please make sure that the SIM card is installed correctly The device does not identify the old SIM card of 5V and 1 8V Please make sure to use the GREY cable to connect between Phone port and your telephone Otherwise you can not hear the dial tone and can not dial out any number Please make sure the cable length between the device and your telephone is less than 100 meters If this device is upgraded we will not notice the user The real appearance and function of this product are based on the real substance The EMI and ESD protection circuitry don t response or input impedance of the audio input The audio signal has a flat frequency response between 300 and 3400 Hz Outside this range the response will attenuate sharply 1 Main description 1 1 Features Conversion of wire amp wireless communication Auto select economic route LCR With LCD display for easy programming Code Conversion Setting Through the connection towards local PSTN line the phone calls will proceed with code transfer dialing process Volume modulating setting 1
10. ix number just input 13 press Enter key to input another GSM prefix number 8 5 2 Delete GSM prefix number Press UP DOWN key to review all GSM prefix numbers Twice press Enter when the second row of LCD display DEL you can delete GSM prefix numbers Pick up the handset of telephone input GSM prefix number then press to finish input You can input to delete all GSM prefix numbers For example To delete 13 as a GSM prefix number just input 13 then press Enter key Press Menu key to return main menu 9 Block number setting Note The block numbers are used for GSM routing only The maximum numbers of this setting are 30 groups the maximum length of each group is 12 digitals 9 1 Press Menu key when the device is standby 9 2 Press UP DOWN key to choose 4 Block Number 9 3 Press Enter key LCD will display blocked codes press UP DOWN key to review all blocked codes 9 4 Press Enter key again to add block codes LCD will display ADD BLOCK CODE on the top Pick up the handset input Prefix number For example To add 00 as block number just set OO 9 5 Repeat press Enter key LCD will display DEL BOLOCK CODE on the top Pick up the handset input Prefix number For example if you want to delete 00 just input OO Input to delete all blo
11. n Disable Enable Assign and Enable Free gt Ifyou select Disable mode the device will not transfer the calls from GSM gt If you select Enable Assign mode when someone call the SIM card number of this device the device will transfer the call to an appointed PSTN number Press Enter key to set this number then press to save and exit gt If you select Enable Free mode when someone calls the SIM card number of this device the device will give a Beep sound to prompt caller and let caller to continue inputting destination number The caller can also input short codes See section 12 Short codes setting when he heard Beep sound Press Enter key to set this number then press to save and exit Note For GSM to PSTN transfer function you must set Permitted Code in 6 TRANS RESTRICT Only after you have set the permitted GSM codes successfully the calls can be transferred otherwise the telephone which is connecting the device will ring 11 Transfer restrict setting Note Only when someone calls the SIM card number of the device this function is available The maximum number of this setting is 30 groups the maximum length of each group is 12 digitals 11 1 Press Menu key when the device is standby 11 2 Press UP DOWN key to choose 6 TRANS RESTRICT 11 3 Press Enter key LCD will display permitted codes press UP DOWN key
12. n P O PSTN call out G l GSM call in G O GSM call out 6 3 Press UP DOWN key to show other records 7 Date and Time setting 7 1 Press Menu key when the device is standby 7 2 Press UP DOWN key to choose 2 Date amp Time 7 3 Press Enter key LCD will display Day Month Year Hour Minute Press UP DOWN to set the Items and press Enter to save 8 Work mode setting 8 1 Press Menu key when the device is standby 8 2 Press UP DOWN key to choose 3 Work Mode 8 3 Press Enter key LCD will display Single GSM Dual PSTN GSM or Single PSTN 8 4 Press UP DOWN key to choose right work mode and press Enter key to save 8 5 GSM routing number setting If you choose PSTN GSM mode the top row of LCD will display Set GSM Dial code the second row will display Enter Y Menu N press Menu key to return and press Enter key to set GSM prefix numbers The maximum GSM prefix numbers are 30 groups The maximum length of each group is 10 digitals For example 9 means when user dialing 9xxxxxxxx calls will be sent out from GSM routing 8 5 1 Add GSM prefix number Press UP DOWN key to review all GSM prefix numbers Press Enter to add GSM prefix numbers Pick up the handset of telephone input GSM prefix number then press to finish input For example To set 13 as a GSM pref
13. nfirm and enter Table 1 1 LED and Button 1 3 Rear panel and interfaces Item Interface Description Antenna SMA Connect with a whip antenna 3 M RG58 cable PTP BD RJ 45 For data tariff download Printer DB 9 F For print out call list Optional Line RJ 11 Connect to PSTN line Phone RJ 11 Connect to phone or payphone ON OFF Power switch BAT For extended backup accumulator battery 6V 4AH DC 7 5V AC DC power adaptor port Table 1 2 Interfaces 2 Work mode This device has 3 work modes GSM only PSTN only and PSTN GSM 2 1 GSM only mode A GSM mark will be displayed on the top right corner of LCD User can only dial and receive calls from GSM only under this mode 2 2 PSTN mode A PSTN mark will be displayed on the top right corner of LCD User can only dial and receive calls from PSTN line only under this mode 2 3 PSTN GSM mode A PSTN GSM mark will be displayed on the top right corner of LCD User can dial out either from PSTN or GSM under this mode When user has set GSM prefix number the calls will switch to GSM routing automatically as a least lost router Note If the power supply is broken or if the device is turned off all the calls will go through PSTN line 3 Installation 3 1 Open the cover board of bottom side then insert SIM card 3 2 Connect the GRAY cable to Phone port and telephone 3 3 Connect the White cable to Line port and
14. not detect any SIM card Please check the contact spring of the SIM card holder or the contact point of the SIM card to see whether there is abrasion ageing or stain in the SIM card And then install the SIM card again 3 Bad connection of antenna or antenna rupture please check whether the core of the antenna is well connected or change the antenna 4 Telephone setup Please check whether the dialing system is DTMF or whether the phone lock is opened 1 Bad connection of antenna or antenna rupture please check whether the core of the antenna is well connected Network indicator or change the antenna flickering fast 2 Weak signal Please adjust the position of antenna and observe signal quality of LCD screen to get the best call effect LCD display Error PIN SIM card locked user access be refused Please connect with vendor or owner to unlock Power indicator OFF 1 Connection problem of power adaptor or backup battery Please check the status of power adaptor or backup battery 2 The adaptor or main board is burned Please contact with your provider No dialing tone 1 It is possible that the grey cable isn t used to connect with your telephone or payphone You should use this special cable to connect between the terminal and telephone payphone The definition of the gray cable is shown in section 16 1 2 Bad line connection Please check whether the electrical function of
15. o amp G Fixed Wireless Terminal FCT 355 User Manual MAXCOMM CO LTD Introduction This Users Manual mainly introduces the FCT 355 3G GSM FWT_FXO converter developed by our company It includes the equipment type performance and specification structure and application described in details in corresponding chapters This User s Manual is the first edition Our company reserves the right of upgrading the edition FCT 355 3G GSM FWT_FXO converter USER MANUAL Version 1 0 Date July 28 2007 Copyright of First Edition 2007 All rights reserved No part of this document may be reproduced or used in any form or by any means including but not limited to photocopy photograph magnetic or other record without the prior agreement and written permission Very Important Notes Before installation 10 11 Please make sure the area where the converter is used can receive radio frequency signal Please never use the equipment in an environment where exist explosive possibilities for example gas station chemicals flammable gas gas transport car or warehouse Please never use the equipment in an explosive area or a place where marked with Turn off Wireless Transmitting Device This device should be avoided using in the hospital for medical electronics equipment such as pacemaker and audiphones are easily disturbed by it There would gender electromagnetic field around the equipment so please never put other
16. phone Please check your telephone payphone or change it 2 Terminal set error or terminal failure Please contact with your provider Off hook and busy tone Please check the network Note Special statement Any result due to the action of changing the parameters of the equipment without the certification of our company has no relation with our company And please never randomly change the SIM card to test the equipment for the users who has set the reciprocal SIM card lock function Please use the original card to avoid unnecessary trouble caused by SIM card 16 3 Typical Applications i AN be A Most User PABX Converter PSTN Line Phone A To be a PABX Extension i 4 Q es gt f a iMoti e User PSTN Line 2 PABX GG Co nete erm odie ea g esm gt i i tA Pa d or a a PSTN it Converter C To be a Mobile call Transfer Box 18
17. s Hand Free to receive the call 5 3 When user receives a GSM call under PSTN talking Beep sound can be heard from the telephone That means there is a GSM call incoming user can receive this GSM call when he finished PSTN talking 5 4 When user receives a PSTN call under GSM talking Beep sound can be heard from the telephone That means there is a PSTN call incoming user can receive this PSTN call when he finished GSM talking 5 5 When the device is used as a PABX extension it maybe transfers a call from PSTN to GSM mobile phone You must set the transfer function If the GSM mobile phone is rejected receiving the call the call will be returned to the telephone which is connecting the device For example If someone is calling in from PSTN line and extending to 803 the call maybe will be transferred to GSM mobile phone Suppose that the GSM mobile phone is rejected receiving the call then the call will be returned to telephone A PSTN Line Telephone 801 Telephone A 803 Telephone Device TelephoneA Mobile Phone 802 6 Call Record User can review the latest 20 records remain in the device 6 1 Press Menu key when the device is standby LCD will display 1 Call Record 6 2 Press Enter key to show the first record The top row display Call Type Call Duration and Call Date Time the second row display dial ID Call Type P l PSTN call i
18. vert code setting is used for GSM routing only the maximum numbers of convert codes are 30 groups the maximum length of each group is 7 digitals 14 10 1 Press Menu key when the device is standby 14 10 2 Press UP DOWN key to choose 7 Convert Code 14 10 3 Press Enter key LCD will display convert code setting press UP DOWN key to review all convert codes For example 0 gt 179510 means 17951 is a GSM IP code after set this code when you dial Oxxxxxxxx it will send out 1795 1Oxxxxxxxx 14 10 4 Press Enter key again to add convert codes LCD will display ADD CONVERT CODE on the top Pick up the handset input Prefix number Converted Number then press to save and ready to add another convert code Press Menu key to return For example if you want to convert 95 to 0 just input 95 0 After set this code when you dial 95xxxxxxxx it will send out Oxxxxxxxx 14 10 5 Repeat press Enter key LCD will display DEL CONVERT CODE on the top row Pick up the handset input Prefix number For example if you want to delete 95 gt 0 just input 95 Input to delete all convert codes 15 Technical Parameters 15 1 Power supply AC Input voltage 160V to 280V Power adaptor output DC7 5V 1 5A Backup battery 6V 4AH Lead Acid battery Optional accessory Maximum charge current 60
Download Pdf Manuals
Related Search