User Manual
Contents
1. User Manual aoe Volume Control Battery Type RO3P AAA Battery voltage 1 5V 2 Standby current 0 040mA Ni fees ee ff working Current 100mA i 1 Power ON self test T The unit will sound as DiDi on loading battery Sensitivity Control 2 Switch on the unit Hold press V key for 3 to switch on the unit the 3 groups LED indicators will flash thrice and speaker will sound thrice Then the unit will enter stand by mode 3 Adjust the volume In standby mode press V key to adjust the volume there are 6 levels including mute 4 Select the tone ANACONDA In standby mode press T key to set sound tone There are 7cycle optional tones for choice NAY 5 Senstivity adjustment J ee To change the senstivity of the unit press S key There are 4 levels for choice initial setting is max level The unit will be triggered in case the fishing line move 3 5mm distance in case the senstivity level is set as max level The aker will beep once to indicate the sensitivity is set as level 1 beep twice as level 2 and so on 6 Casting or winding fishing line identification The unit is able to indentify the fishing line is casting or winding There are 7 cycle optional tones for choice for casting the fishing line and only 1 tone for winding the fishing line 7 Night Light In standby mode hold press T key for 1 5 will start night light The LED under the roller will light up hold press T key for 1 to turn it2. 048 602 604_EN indd 1 31 10 14 08 21 NIANA TIK AKA RECEIVER Volume Memory Ae User Manua pu Al d past arm mode uA Battery Type 6F22 mii Battery voltage 9V Power off current consumption OMA Tone 1 Switch on the unit Load battery then switch Power button on the back side of the unit to ON Five LED indicators flash in sequence of red gt green gt blue gt yellow and the unit will beep as DiDiDiDi Then the unit enter standby mode 2 Adjust the volume In standby mode press V button to adjust the volume there are 6 levels including mute 3 Select the tone In standby mode press T button to select sound tone there are 7 cycle optional tones for choice 4 Alarm mode selection In standby mode press the function key on the left down side of the receiver to select alert mode there are 3 modes for choice light sound mode light sound vibration mode or light vibration mode 5 Function for KEY M In standby mode press M key will indicate the last recorded alert received from transmitter 6 Pair transmitter to your receiver In standby mode you may choose one channel to pair a transmitter First please choose the channel you need to pair press S key to choose the 1st channel and the red indictor will light up Press S again and again will change indicator in sequence of red gt green gt blue gt yellow from left to right on your unit
3. Each color indicator represents one channel Suppose you choose the blue indicated channel on receiver rotate the roller on the transmitter the receiver will resoonse by beep and the blue indicator on transmitter flashes this indicate the paring job is done Just following the same steps to pair other transmit ters You need change to other channel in case you find the indicator light is weak while paring as this means the channel is already paired to some transmitter Or you may choose to erase the saved setting for this channel then pair to a new receiver Please refer to the below instruction for how to erase the paired code 7 Erase the paired code To erase the paired code in the receiver press the S key in standby mode select LED indicator to choose the channel you need erase then press S key till the light change from low light to high light 8 Erase all the paired code in the receiver To erase all the paired code in the receiver press S key and do not release till the 4 LED indicator flash at the same time then release the key All the paired codes will be erased 9 On working In standby mode the receiver will alert in selected mode in case transmitter start alarm You will see the pairing LED indicator lights up and the white LED indicator flashes the receiver will stop alert in case transmitter stops alarm the white LED indicator truns OFF and the paring LED indicator flashes which means there has been some alert
4. OFF 8 Low battery detection low battery alert The unit will auto detect the battery voltage in standby mode in case battery voltage is lower than setting the speaker will generate DiDi sound you should replace the battery imediately to ensure the unit works normally In case battery is not replaced in time the unit will beep at intervals of 1 minute till battery is replaced 9 On working In standby mode roll the roller will trigger on the speaker and the LED indicator In case fish line is move forwarde the LEDs on the left side and down side of the roller flash in case fish line is move backward the LEDs on the right side and down side of the roller flash the unit transmits alert signal to receiver In case the roller stop rolling the speaker and signal transmition will stop the LED stop flashing and keep light on then switch off after another 15 10 Power OFF Press V key for 1 5 to turn OFF the unit The 3 groups LED indicators will flash once and there will be DiDiDi sound NOTICE 1 The max battery voltage should no more than 5V otherwise may have the internal electronics parts damaged 2 Each main unit receiver only work and response to paired transmitter s 3 To save energy the main unit should be powered off in case no usage The battery should be taken out in case long time no use 4 To ensure good performance please make use of good quality battery WWW SAENGER TTS DE Seite 1 Manual 2
5. The unit will return to stand by mode in case no further alert signal is received in the coming 10 seconds 10 Low battery detection low battery alert The unit will auto detect the battery voltage in standby mode in case battery voltage is lower than expectation the speaker will generate DiDi sound you should replace the battery imediately to ensure the unit works normally In case battery is not replaced in time the unit will beep at intervals of 1 minute till battery is replaced 11 Power OFF Switch the unit to OFF to turn the unit off 12 Auto save Function The unit will keep setting in memory The last setting will be recalled even the unit is powered OFF or the battery has been removed NOTICE 1 The max battery voltage should no more than 10V otherwise may have the internal electronics parts damaged 2 Each main unit receiver only work and response to paired transmitter s 3 To save energy the main unit should be powered off in case no usage The battery should be taken out in case long time no use 4 To ensure good performance please make use of good quality battery Seite 2 WWW SAENGER TTS DE Manual 2048 602 604 EN indd 2 31 10 14 08 21
Download Pdf Manuals
Related Search