XD-16 Digital Universal Dash Display User Manual
Contents
1. Info Log Connection Input Min Hold Max Hold Alarm Colors Select Input to be displayed MA input Info Range Oto 10230 RPM Will be displayed as Oto 102 x100 RPM Limit displayed range to lo to 10230 RPM Apply Limit Limit outside LED indicated range to lo to 110230 RPM Leftmost LED Rightmast LED As you can see here the display will indicate in 100 RPM This might be too coarse for many applications The limit is there because the XD 16 can only display 3 digits By applying a limit for example to 0 9990 RPM the 9 XD 16 can display the RPM in multiples of 10 RPM Ifa channel is selected that has both positive and negative values a different screen will show ua LM Programmer Version 3 00 lH xl Info Log Connection Input Min Hold Max Hold Alarm Colors Select Input to be displayed Input Info Range 2 00 to 2 00 g Will be displayed as 0to 2 00g Limit displayed range to Rn w po o Apply Lin E Use left top LED as negative indicator instead of in display fight LED indicates positive value Limit outside LED indicated range to 2 00 to 2 00 g Leftmost LED Rightmost LED This allows you to use the Indicator 1 and 2 LEDs as negative value indicators to preserve the 3 digit resolution of the XD 16 6 Once programmed power off the XD 16 and exit LM Programmer Reconnect the XD 16 to your MTS chain Note The XD 16 comes preprogrammed to display A F I2. XD 16 Digital Universal Dash Display User Manual XD 16 Manual_1 4 doc 1 VOT VIC ss ee see 3 2 The XD 16 Device The XD 16 Module 2 1 Identifying the user interface features of the XD 16 u0022240002200000000nnn nennen nennen nnnnnnn nennen nnnnnnnnnenn 4 3 Mounting and Gonnecting the XD TO ns eilt 4 4 Changing the channel display cccccccsssseceeeceesseceesseeeeeeceuaseeesssaageeeess Error Bookmark not defined 5 usinge X DIG air rear a T T NEE 5 6 Programming DER DEI einen 6 6 1 Installing the LM Programmer Software cccccccccccsseeeeescceeeeeescasseceesscaseneeessceseeeeesousneeessoassseeesssooess 6 6 2 Connecting the XD 16 device to the computer uusss 222240000seennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnn 7 6 3 Updating the Firmware attics sen 7 64 Selecting the display Channel ans inden dacs nd 9 6 5 Programming the Min Max hold functions ccccccsseeeeceeseeeceeseecceseeeceaeeeceeseeeessaseeessaesessenseesseaseeeeses 10 6 6 Programming the Warning Alarm function ccccccccccceeeceeceeceeeneeeeeeeeeeesseeeeesseeeeesaueeessaeeeeeseaeesesseseeeeeas 11 6 7 Programming the Analog needle colors ccccccccccesececceeseecceeseeecceuseeceageeecsaseeeseuseeessageeessagseesseeeeesas 13 7 Changing ihe gauge face Of ie XD 16 5 uns aei e ae esl cesestenaceenteschendtest eas N 14 GN installing the NeW gauge Rate aa
3. can be different than the screen colors With the sweep test button the XD 16 will sweep through all LEDs from left to right to give you and indication on how the color scheme you programmed will look in real life To change multiple LEDs to the same color just program one LED Then drag this LED over the other LEDs you want to program to the same color 19 2 6 Changing the gauge face of the XD 16 When you use the XD 16 to display different channels than AFR or Lambda you very likely want to change the gauge face As the LM 1 MTS system can be programmed for any 0 5V sensor the possibilities are endless Because not every possible use can be anticipated the XD 16 is designed to allow user customization 6 1 Installing the new gauge face 1 Lay the XD 16 face down on a table and remove the three Phillips screws from the outside rim of the back plate Carefully lift out the back plate with the electronics package from the bezel Laying the electronics package on its back first place the gauge face followed the glass and bezel Be sure to remove protective film from the gauge face This can be done easily with a piece of scotch tape Make sure every piece is positioned correctly on the button shaft Carefully flip the complete assembly and line up the screw hole of the bezel with the screw hole of the back plate ensuring that everything slides into the bezel correctly Holding the assembly together with one hand test the operatio
4. the LM Manager software The recovery mechanism is designed to be able to recover 99 9 of the time While we don t anticipate this occurring it is possible that the XD 16 will not recover correctly and may need to be serviced at our factory If you suspect this is the case contact Innovate support 5 4 Selecting the display channel 1 Prior to selecting a channel to be displayed you must first tell the system what channels are available With your MTS chain connected together connect the serial OUT of the last XD 16 to your computer and launch LogWorks 2 Make sure that all your channels are setup properly go into Channels Configure Channels 3 Once you have all your gauges setup properly in LogWorks you may exit the application and power the MTS system down 4 Remove the XD 16 which you want to reprogram from the MTS serial chain Insert the terminator plug in the serial IN of the XD 16 and the cable that goes to the computer to the serial OUT Launch LM Programmer 5 Once in LM Programmer go to the Input tab The LM Programmer will read the MTS record You will now be able to select the channel that you want the XD 16 to display ra LM Programmer Version 3 00 Display AFR Display Lambda Limit outside LED indicated range to 10 0 to 13 4 AFR Leftmost LED Rightmost LED If you select something other than a Lambda AFR channel the display will change to _ LM Programmer Version 3 00 i lOl x
5. the XD 16 for the selected channel input 3 Manuals 4 Example Log Files 5 2 Connecting the XD 16 device to the computer 1 Connect the Serial OUT connection with the included 2 5mm stereo to DB 9 cable to a serial port on your laptop 2 Connect the terminator plug 2 5mm male plug with no cable into the Serial IN connection of the XD 16 Start the LM Programmer software The screen should look like this a LM Programmer Version 3 00 5 x Info Log Connection Input Min Hold Max Hold Alarm Colors 2003 2004 Innovate Technology Inc INNOVATE Device Type Seral Display XD 1 Firmware Version 1 00 Connected to pot COM Processor Version ATM16 8 5 3 Updating the Firmware The LM Programmer Info Set AFR tab reports the firmware version currently installed on your unit Do not update the firmware if the versions are the same A firmware update should only be necessary if there has been a new release Click the Update Firmware in the main page to upgrade to the latest firmware for the LC 1 Firmware for the LC 1 has the extension did New firmware releases are available on the Innovate Motorsports web site www tuneyourengine com under Support If your computer crashes during a firmware upgrade the XD 16 has a recovery mechanism where it will be able to retry the download again and not be disabled by half loaded firmware Switch the XD 16 off and on again and then try to restart
6. N 3735 Includes patch cable for LM 1 P N 3759 see below ST cose Fos ma T ___ QUICK START GUIDE Appendix C Limited Warranty LIMITED WARRANTY Innovate stands behind the quality of its products Innovate makes the following warranty to purchasers of its products All new Innovate products carry a six month warranty from the date of purchase If proof of purchase cannot be provided warranty will be determined by date of manufacture When Warranty Void This warranty shall terminate and Innovate shall have no obligation pursuant to it if i your Innovate product has been modified or repaired in a manner not previously authorized by Innovate in writing ii the identification markings on your Innovate product have been removed defaced or altered iii your Innovate product was subjected to accident abuse shipping damage or improper use iv your Innovate product was not used or configured as specified in the product manual or v your Innovate product was subjected to operating conditions more severe than those specified in the product manual Exclusions From This Warranty Oxygen Sensors are excluded from this warranty Repairs Under This Warranty In the unlikely event that your Innovate hardware product should prove defective during the warranty period contact Innovate Customer Support for a return material authorization RMA at 949 502 8400 Products returned for service must be securely packed to prevent damage
7. a ont arate iecentens onion tanidenek isms 14 Te GtedleacUstom labelia sen ss ae ai 15 7 3 Assembly sequence of the XD 16 with foil face 2 44000440400RRnennnnnnennn nennen nnennnn nennen nnennnnnnnnne nennen 15 Appendbe Ar SpEciiicatiens anna na 15 Appendix B Kil GONtEnse ee ae ai 16 Appendix Gs Eimited Warraniyalzsss ae ae ee 17 FACVISION HISTORY sa ae Renee 18 1 Overview The XD 16 is a programmable digital display used as dash mounted instrument for the Innovate Motorsports sensor devices The XD 16 fits into a standard 52mm 2 1 16 gauge hole Multiple XD 16 s can be daisy chained to build and entire programmable dash XD 16 gauge faces can be user customized The XD 16 can also be used to initiate and control recording on the LM 1 or other Innovate Recording devices can initiate free air calibration for Innovate Motorsports wideband controllers and indicate wideband controller status In addition the XD 16 can be programmed to hold minimum maximum values of the displayed channel and provide warnings alerts depending on programmable warn conditions 2 The XD 16 Device The XD 16 set contains the following parts The XD 16 Module Analog Pointer LEDs Light Sensor Function _ _ Function indicator 1 Y oe Indicator 2 Main Humer Display Contral Button Record Indicator 2 1 ldentifying the user interface features of the XD 16 The analog pointer LED s 21 total act as a digital
8. and shipped charges pre paid along with proof of purchase and the return material authorization number to the Innovate repair location as instructed by Customer Service Innovate within a reasonable amount of time from its receipt of your product so shipped will ship to you at its option the repaired product or a new or reconditioned product of comparable or greater specified functionality All repaired or replacement products shall be warranted for the remainder of the original product warranty Disclaimer INNOVATE MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO YOUR INNOVATE PRODUCT OTHER THAN THE LIMITED WARRANTY SET FORTH ABOVE No Innovate dealer agent or employee is authorized to make any modification extension or addition to this warranty unless enforceable or unlawful under applicable law INNOVATE DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY NONINFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE AND THE LIABILITY OF INNOVATE IF ANY FOR DAMAGES RELATING TO ANY ALLEGEDLY DEFECTIVE PRODUCT SHALL UNDER ANY TORT CONTRACT OR OTHER LEGAL THEORY BE LIMITED TO THE ACTUAL PRICE PAID FOR SUCH PRODUCT AND SHALL IN NO EVENT INCLUDE INCIDENTAL CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES OF ANY KIND EVEN IF INNOVATE IS AWARE OF THE POSSIBILITY OF SUCH DAMAGES Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
9. chain has 12 channels 6 from LM 1 1 from LC 1 and 5 from LMA 3 If you are running LC 1s the rule is LC 1s first then LMA 3s SSI 4s and TC 4s Then goes the DL 32 which is going to record the information coming from the other products Lastly you connect your XD 16s which can be setup to display any channel in the serial chain To Computer 4 Using the XD 16 When the XD 16 powers up it will briefly go through a sequence where it lights up all its LEDs This is a function and diagnostic test Holding down the Control button during power up will continue to light up all LEDs until the button is released 4 1 Sensor Warm up For example this would indicate that he heater is warmed up to 56 The Function Indicator 2 is lit 4 2 Heater Calibration The last digit is the count down of the heater calibration 4 3 Free air calibration in process When shown steady free air calibration is in progress If blinking and not going away after 5 seconds the LM 1 requests a free air calibration as happens after a heater calibration Blinking CAL can also happen if the control button is pressed rapidly 3 times Pressing it then again initiates a free air calibration If this is unintentionally pressed the CAL request goes away after 5 seconds 4 4 Normal Operation With function indicator 1 lit this shows AFR 4 5 Normal Operation very lean mixture or free air Switching between cud and od Shows the free air content of
10. cket leaving the XD 16 cables in the back accessible 3 Connect the RED wire from the back of the XD 16 to a switched 12V source in your car A switched 12V source goes on as soon as the ignition on the car is on or the engine runs Make sure the connection is fused with at least a 2A fuse 4 Connect the BLACK wire to ground The ground should be shared with other MTS devices for example LC 1 DL 32 SSI 4 TC 4 LMA 3 etc 5 Connecting Signal Source 5 1 If connecting to a LM 1 connect the LM 1 patch cable P N 3759 to the LM 1 s Serial Port Plug the 2 5mm male stereo end into the XD 16 Serial IN port female 2 5 mm socket marked IN 5 2 If connecting to an LC 1 or other MTS device connect the male 2 5mm Stereo to male 2 5mm Stereo cable between the Serial OUT port of the device to the Serial IN port of the XD 16 The rule is LC 1s first then LMA 3s SSI 4s and TC 4s Then goes the DL 32 which is going to record the information coming from the other products Lastly you connect your XD 16s which can be setup to display any channel in the serial chain 6 If using a computer to datalog or download LM 1 data connect the XD 16 to Computer cable between the Serial OUT port of the XD 16 and the computer s serial port The following diagram show how to connect multiple Innovate Motorsports devices to form a logging and display chain The example chain consists of a LM 1 a LC 1 a LMA 3 and 2 XD 16 s In this case the
11. damages so the above limitations or exclusions may not apply to you 217 Revision History 1 0 2 5 05 Initial release 1 1 3 16 05 Corrected misc errata 1 2 4 11 05 Corrected section 2 2 1 3 2 06 06 Added XD 16 information 1 4 08 23 07 Added Appendix B Kit Contents 18
12. f you have multiple A F channels the unit will display the first one on the chain 5 5 Programming the Min Max hold functions Click on the Min Hold or Max Hold Tab on the top of the window The following screen will show up 10 LM Programmer Version 3 00 I x Info Log Connection Input Min Hold Max Hold Alarm Colors W Enable Function Hold only if Throttle jsmorethan 77 is less than feo k for at least foa Seconds max 10 Seconds Programming the Min or Max hold function should be pretty self evident You can enable the function You can also make the hold function depending on another channel In this example the Max hold function will be programmed so that the leanest AFR is only stored during WOT operation and only if the condition persists for more than 0 2 seconds In this case AFR was used as input and you don t want to store the leanest AFR during closed throttle where the injectors cut off Any channel can be programmed as dependency You can program any minimum persist time between 0 and 10 seconds 5 6 Programming the Warning Alarm function Click on the Alarm tab on the top of the screen oe ras LM Programmer Version 3 00 Again the programming is very similar to the Min Max hold programming as described in 4 6 Except here the Alarm condition can be programmed to be dependent on two other channels and time During an Alarm the XD 16 will flash the indicated value a
13. lay mode Pressing the Control button while the blinking CAL is displayed will initiate a free air calibration on ALL connected wideband devices 5 Programming the XD 16 You will need 1 XD 16 to Computer cable male 2 5mm Stereo to DB 9 2 XD 16 Terminator plug single male 2 5mm Stereo plug 3 A laptop computer 4 When powered by the car the ignition of the car must be on to power the XD 16 Alternatively you can power the XD 16 with a suitable power source between 8V and 25V A normal 9V battery can be used to power the XD 16 Always disconnect and connected the serial ports labeled IN and OUT with the unit OFF 5 1 Installing the LM Programmer Software Put the included CD in your CD drive on your computer and follow the instructions on screen The Software will be installed including pre set directories for log data and downloaded software The LM Installer also puts entries for the LM Software in the Start Menu of your computer under the heading Innovate Ge The following items will be installed on your hard drive 1 LM Programmer This is used to program the XD 16 2 LogWorks This is a comprehensive data logging and analysis package to download and analyze engine data recorded with Innovate devices It also allows real time logging and display LogWorks allows you to program the relationship between sensor voltages recorded by the LM 1 or LMA 3 and the indicated values This relationship will be programmed into
14. n of the button and as necessary adjust by rotating bezel glass and gauge face Reinstall the 3 Phillips screws 14 6 2 Create a custom label Note To customize you will need to use a blank white gauge face supplied with every XD 16 Innovate Motorsports will provide downloadable pdf file templates for the most common sensors at www innovatemotorsports com Print these templates on clear overhead foil suitable for your printer Any stationary store carries those Depending whether you use an inkjet or laser printer different foils will be needed Exacto knife or razor blade or scissors Piece of plywood or sturdy cardboard as cutting background Do not use the kitchen table A 1 8 hole punch Leather equipment stores or horse tack stores carry those A small Phillips screw driver Blank white XD 16 face included S aloe ea 6 3 Assembly sequence of the XD 16 with foil face D w Bezel Electronics Package Front Control and back plate Glass Blank button Printed face foil face Appendix A Specifications Supply voltage range 8V to 25V Current draw lt 600 mA Weight 30z 82g Serial port speed 19 2 kb Max serial port cable length 15 ft Current draw depends on outside brightness and number of LED segments lit 15 Appendix B Kit Contents Standalone Gauge Kit P N 3781 As Shown below XD 16 Kit P N 3780 Excludes LC 1 Sensor P N 3737 and Bung Plug P
15. nd the analog needle LEDs at maximum brightness until the Alarm condition goes away 12 5 7 Programming the Analog needle colors Click on the Colors tab iat LM Programmer Version 3 00 oj x Log Connection Input Min Hold Max Hold Aam Colors Min Hald Max Hold Indicator color BU E a LQ indicator color u gt 13 8 15 6 16 1 12 8 16 6 Double 123 17 0 ui a ae Br 75 other LED change E iii 18 0 8 set tto ine Same color 109 18 4 oz Ovo ez KR Factory default colors Sweep Test This shows the current color settings for all the 21 LEDs plus the indicator colors used when reviewing Min Max hold To change the color of an individual LED double click with your mouse on the LED to change The following dialog box will show up Set Color The currently selected LED is also highlighted By changing the sliders for red green and blue any color out of a set of 32767 colors can be created Any color can be created by mixing red green and blue light at varying ratios The XD 16 can be programmed for 32 different values for each red green and blue And 32x32x32 is 32768 But black all off is hardly used While moving the sliders the simulated LED on the screen changes color and also the appropriate LED on the XD 16 at the same time Because computer screens use a different technology to create colors than the XD 16 the actual colors on the XD 16
16. needle The range and individual colors of this needle is freely programmable The Function indicators 1 and 2 are used to indicate between display heater warm up or O2 content when the XD 16 is programmed as AFR Lambda display default When used to display other channels the indicators can be used to indicate the sign of the displayed value By using the indicators as sign display positive or negative one of the three numerical displays is not wasted to show a sign This functionality is programmable The main numeric display shows the numeric value of the displayed channel When the XD 16 is used as AFR Lambda display it will also show the status of the wideband controller The light sensor allows the XD 16 to adjust its brightness to the light level of the environment At night the full on display would be much too bright and would interfere with the operation of the vehicle During sunlight the XD 16 will go to maximum brightness to allow readability The Control Button is used to control various aspects of the XD 16 and attached wideband controller or recording device like the LM 1 The record indicator will blink when a LM 1 or other Innovate Motorsports recording product is attached and actively recording 3 Mounting and Connecting the XD 16 1 If not using a commercial gauge pod cut a 52mm 2 1 16 hole into the intended dash location 2 Insert and mount the XD 16 and mount it with the included mounting bra
17. the gas the sensor sees 4 6 No Connection detected If the display shows lll The XD 16 cannot receive data from the LM 1 or other devices Make sure all the connections are fully seated 4 7 Start Stop Recording Press the Control button once to start recording The Record indicator light will blink Press the Control button again once to stop recording The Record indictor will switch off 4 8 Clear Recording Memory of LM 1 5 Press and hold the Control button until rES for Reset shows 4 9 Review Min Max hold Press the Control button twice rapidly The XD 16 will show the last minimum value indicated Note that the XD 16 will remember the minimum value even if power is switched off Minimum value is indicated by alternating between Lo and the minimum value stored Holding the Control button down for a few seconds while this is displayed will reset the minimum value Press the Control button instead only briefly will show the maximum value indicated It is indicated by alternating between Hi and the maximum value stored Press the Control button again briefly to return to normal operation Holding the Control button down for a few seconds while this is displayed will reset the maximum value 4 10 Initiating a free air calibration Press the Control button three times rapidly The display will show a blinking If the button was press accidentally three times wait for 5 seconds The XD 16 will return to normal disp
Download Pdf Manuals
Related Search