user manual - power-pond
Contents
1. POWER POND ysg Solar Charqer 7 2 Watt user manual for POWER POND use Solar charger 7 2 Watt www POWER POND de POWER POND USB Solar Charqer 7 2 Watt Content First steps general use of the USB solar charger page 1 3 Using with mobile devices page 4 Using with Apple devices page 5 Specifications page 6 Troubleshooting page 7 General notes on batteries page 8 How can I measure the performance of the USB Solar Charger right page 9 11 Need help with the USB solar charger Call 0049 6471 3801767 www POWER POND de POWER POND USB Solar Charger 7 2 Watt First steps general use of the USB solar charger The POWER POND USB solar charger converts sunlight into energy The stronger the light source the more energy is produced Unfold the solar charger and towards the sunlight source making sure the solar sunlight receives as much sunlight as possible Plug your original charging cable to the mobile device to connect it with the POWER POND USB solar charger With the nylon loops attached along the edge you can suspend and firmly secure the USB solar power charger v www POWER POND de POWER POND usp Solar Charger 7 2 Watt The presence on the inside pocket is suited well for storing smaller an external power bank and smaller Smartphones www POWER POND de POWER POND usp Solar Charger 7 2 Watt Next to the aforementioned pocket is another loop With it you can fold the top2. age to charge the battery Many users may notice only the shortened term of the instrument Most fresh batteries require an input voltage of about 500 800 mA at about 5 0 to 5 3 volts Basically the consumer device determines the required voltage NOT the power source The power source provides only the maximum voltage available Even if you have a 2000 mA output but only 500 800 mA smaller devices such as smartphones are usually needed not available in 2000 mA The charging behavior and the energy need is always dependent on the manufacturer type age of the battery and ambient temperature falls and always different from How can measure the performance of the USB solar charger right www POWER POND de POWER POND USB Solar Charger 7 2 Watt Quite simple really but please note a few things In order to achieve accurate power measurement please connect a USB rechargeable battery having at least 30 capacity behind the USB power meter Why can t I use my phone The mobile phone is NOT the full power decrease the internal limit in the mobile phone this regulates by itself Why do have to take a USB battery Power Bank This performance is taken as it arrives straight and the full available energy is therefore used Why should the USB battery have at least 30 If the USB battery is empty the existing reacts in the USB battery electronics such as a cell phone and loads very gently at first the USB battery unti
3. l it has reached a certain capacity Here are some pictures for illustration www POWER POND de POWER POND USB Solar Charger 7 2 Watt om Amperemeter It measures the current flowing Current V and A and adds the percolated Ampere the measured current from an iPad mini is about 643 mA on iPad 2 about 678 mA Devices switch to a 12000 mAh USB Battery The measured current here is about 917 mA www POWER POND de POWER POND www POWER POND de paqe Il
4. part position of the pocket and the USB port completely to the rear In strong sunlight the dark materials mounted there will heat up very quickly Wwww POWER POND de POWER POND usg Solar Charger 7 2 Watt Using with mobile devices Connect your mobile device to the USB port of the POWER POND solar charger via your charging cable when sunlight is sufficient The charging process starts immediately The respective charging voltage and speed mainly depend on the intensity of the available sunlight The electronics automatically determines the required charging Voltage V and current mA of the device www POWER POND de page 4 POWER POND usp Solar Charger 7 2 Watt Using with Apple devices Apple devices need more power than any other devices on the market Therefore you must pay particular attention to there being enough sunlight If the energy output of the solar charger falls below a certain threshold the message accessory is possibly not supported appears in the display screen The energy used by Apple devices is about 1 3 below that of the conventional devices available on the market The mobile devices of Apple also need a higher voltage for charging Thus the current mA which in turn slows the charge is reduced For larger devices such as the Apple iPad much energy lots of light must be available prior to loading If the Apple iPad do not immediately go into the state of charge please clo
5. safety circuit of the solar charger sets in and turns off and back on automatically This can have the following reasons 1 It is not enough light present Use the solar charger with sufficient light Under 4 2 volts and 400 mA output power the USB port for safety switches off automatically because another charge would affect the battery life 2 Charging the battery below these values decreased substantially and durably the life cycles of your battery The terminal of the battery is worn out due to its age and needs a very high voltage Replace the battery or you are using an intermediate energy storage The available light is not enough to charge the battery but if any that the terminal monitors the charging voltage which has a higher consumption It is primarily dependent on the light output In a dull cloudy day or in the morning or evening twilight the loading speed is much slower www POWER POND de POWER POND Lithium ion batteries as used in most mobile devices typically have a life cycle of 500 full discharges and charges Complete discharge also means twice a discharge to 50 and charging to 100 Also the ambient temperature is a not insignificant factor which favors or limits the life cycle of the battery If the life cycle is reached the battery does not cease suddenly to perform The current storage capacity is radually reduced the charging process takes usually longer and it needs a higher input volt
6. se for two seconds completely the solar modules red indicator light goes off connect the iPad Cover then the solar panels back on For you to avoid charging crashes we therefore recommend you to always use a small or medium size USB Power Bank 3000 6000 mAh they are adequately sized and the size of most external batteries fit into the existing pocket Specifications www POWER POND de POWER POND USB Solar Charger 7 2 Watt Solar panels Performance of one solar unit Energy efficiency Circuit parallel Type of solar cell Sealing the solar cell Max USB output voltage Polyester fabric Folded dimensions Dimensions Weight 4 Max each 5 5 Volt 318 mA 19 2 series Monocrystalline PET lamination 5 5 Volt 1272 mA Abrasion tear and water resistant 600D PVC Remark the cloth with pvc is waterproof but it can t be soaked in water Ca BxTxH 120x180x37 mm Ca BxTxH 575x180x17 mm Ca 3009 www POWER POND de POWER POND USB Solar Charger 7 2 Watt Troubleshooting General Notes on batteries Red LED is not lit Red LED lights up but when plug in a device they will start to flash My device has less battery than before loading shows that it loads My device will load slower than when load it from an AC outlet There is not enough light output available Please place the solar charger directly into the sun The current performance is not enough to load terminal The
Download Pdf Manuals
Related Search