Home

NVF-200LS/RS User's Manual - RubyTech Deutschland GmbH

1. e 109 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de System Diagnostics Power and Cooling Problems If the POWER indicator does not turn on when the power cord is plugged in you may have a problem with the power outlet power cord or internal power supply as explained in the previous section However if the unit power is off after running for a while check for loose power connections power losses or surges at the power outlet If you still cannot isolate the problem then the internal power supply may be defective In this case please contact your local dealer Installation Verify that all system components have been properly installed If one or more components appear to be malfunctioning e g the power cord or network cabling test them in an alternate environment where you are sure that all the other components are functioning properly Transmission Mode The default method of selecting the transmission mode for RJ 45 ports is 10 100 Mbps ETHERNET for RJ 11 port are auto negotiation VDSL Therefore if the Link signal is disrupted e g by unplugging the network cable and plugging it back in again or by resetting the power the port will try to reestablish communications with the attached device via auto negotiation If auto negotiation fails then communications are set to half duplex by de
2. DUID Type Type 1 LLT Link Layer Time zi IANA ID IAPD ID SLA ID Rapid Commit Default WAN Heb Se Figure 4 6 5 3 Dynamic IP Address Please Enable IPv6 to set the WAN IPv6 Configuration Select IPv6 Setting IPv6 IPv6 setting on the left navigation bar 42 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 6 5 2 Static IP Address To configure the WAN interface to use a static IP address select the option Static IP Address in the WAN Settings screen A screen is displayed as shown in Figure 4 6 5 4 WARM The CPE dente GA P connected I en sens piovider n ity ef the fobatrg wid Tus Secondary DIS Tarver ade Dal malt VIAM el Figure 4 6 5 4 WAN Static IP The screen contains the following details Fields in Static IP Field Description Address Version IP address assigned by your l To specify the IP Address of VC 400RT CPE s WAN link ISP Gateway Address IPv6 address assigned by your ISP This is the static IP address for the WAN interface IPv6 Gateway Address This is the default gateway IPv6 DNS Servers IPv6 Primary DNS Server uu l This is the primary DNS server Address This option allows to configure default route for relevant WAN Default WAN l mode of this WAN connection 43 RUBY Deutschland GmbH e Networking amp Communications
3. Add Modify a WAN Egress Classifier Rule Classifier Name Enable Disable Acceleration Queue Name Classifier Interface Ingress Interface Classifier Type Rate Control Enable Rate Limit Outgoing DSCP Incoming DSCP T S det queue m Upstream v DSCP Based el oO Kbps Help Figure 4 11 3 1 Add Modify a Classifier Rule DSCP Based Classifier Type Rate Control Enable Rate Limit Outgoing DSCP Incoming DSCP Incoming 802 1P Outgoing 802 1P VLAN Id Source MAC Destination MAC L3 Protocol Source IP Destination IP L4 Protocol Source Port range Destination Port range Order MFC Based v Kbps JI e L Exclude EEE Source MAC Mask L Exclude Destination MAC Mask L Exclude IPv4 e L Exclude Netmask C Exclude Netmask Ys Exclude i Exclude T Exclude Exclude IL d Last Al re Figure 4 11 3 1 Add Modify a Classifier Rule MFC Based 84 CR RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 CT Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in Add Modify a Classifier Rule Field Description m This is the name of Classifier This is an Unique identifier for an Classifier Name l T instance of classifier rule Enable This is used to enable or disable the QoS Classifier entry Classifier
4. Filter Level Default v Figure 4 3 7 System Log This page allows to manage logging options in CPE device If Local is selected the events are logged locally in the system if Remote is selected the messages are logged to a remote server If Local and Remote option is selected messages are logged locally in the system as well as to the remote server The events pertaining to the priority equal to or higher to the selected level will be logged Default level logs all events For viewing system log the events corresponding to the priority level equal to or higher than the selected level will be displayed here 26 CS RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in System Log Field Description ooo Select the mode of log The possible options are Local Mode The log text is displayed in web browser itself Remote Mode Specify the IP address and UDP port number for log transfer using syslog Local and Remote Mode This supports both options mentioned above VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Configure System Log The user can apply one of the following filters to view specific logs of certain level Default The default pre selected levels of logs are viewed Debug Debug and above levels of logs are viewed Info Informative and above level of logs are viewed Notice Notice typ
5. LINE PHONE CONSOLE aJ Figure 3 2 Rear Panel And the table shows the description Table 3 2 Table 3 2 Description of the router rear connectors Connectors Type Description The reset buttons allows users to reboot the VDSL2 or load the default settings Press and hold for 1 5 seconds Reboot the VDSL2 Router Press over 5 seconds Load the default settings l l For connecting to a VDSL2 device Do not use RJ11 and Line RJ 11 Terminal Block l Terminal Block at the same time Gigabit Ethernet l E1 E4 RJ 45 For connecting to an Ethernet equipped device CONSOLE RS 232 For connecting a PC with RS 232 serial port over a D SUB Cable Before user installed power and device please read and follow these essentials Reset Tact switch Button Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point Note Do not run signal or communications wiring and power wiring through the same wire conduit To avoid interference wires with different signal characteristics should be routed separately 13 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de You can use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that
6. To enter the Gateway address of routing entry Enter the Gateway address of routing entry Click Add to create a new static route of specified destination IP Netmask and Gateway values Click Cancel to exit from this page without saving the changes 62 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Notes 1 Static Routing functionality is used to define the connected Gateway between the LAN and WAN For example If we want to activate the Network Time Protocol NTP service and we have to define the Gateway connected to NTP server in the WAN 2 The gateway of static routing just used for switch Bridged mode When you click the IPV6 tab in the Static Routing page a screen is displayed as shown in Figure 4 8 1 1 The addition and deletion of static IPv6 routes is not supported currently Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router You can use static routing to allow different IP domain users to access the Internet through this device uw ITE Prefix Length Next Hop interface E E nl Figure 4 8 1 1 Static Routing IPv6 Tip 4 8 2 RIP Support The RIP support for enabling dynamic routes in CPE may be present in some of pre built packages To enable the RIP support
7. 3 service It can be deployed from central offices from fiber optic connected cabinets located near the customer premises or within buildings It was defined in standard ITU T G 993 2 finalized in 2005 VDSL2 was the newest and most advanced standard of digital subscriber line DSL broadband wireline communications Designed to support the wide deployment of triple play services such as voice video data high definition television HDTV and interactive gaming VDSL2 was intended to enable operators and carriers to gradually flexibly and cost efficiently upgrade existing xDSL infrastructure The protocol was standardized in the International Telecommunication Union telecommunications sector ITU T as Recommendation G 993 2 It was announced as finalized on 27 May 2005 1 and first published on 17 February 2006 Several corrections and amendments were published in 2007 through 2011 VDSL2 is an enhancement to very high bitrate digital subscriber line VDSL Recommendation G 993 1 It permits the transmission of asymmetric and symmetric aggregate data rates up to 200 Mbit s downstream and upstream on twisted pairs using a bandwidth up to 30 MHz VDSL2 deteriorates quickly from a theoretical maximum of 250 Mbit s at source to 100 Mbit s at 0 5 km 1 600 ft and 50 Mbit s at 1 km 3 300 ft but degrades at a much slower rate from there and still outperforms VDSL Starting from 1 6 km 1 mi it
8. VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 p Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in WAN Channel Config Field Description VC Channel Name Channel Name User specified VCC Name Encapsulation Mode for this VCC from dropdown LLC SNAP or VCMux mode Quality of Service for ATM VCC Available options are UBR CBR QoS Mode ET VBR nrt VBR and UBR Gal Deke vae Delay Variation NEMINEM d Delay Variation specified in terms of jitters Click Add to save the information that you have entered Encapsulation Mode Click Cancel to exit from this page without saving the changes 4 6 4 VLAN Channel confg To configure the VLAN Channel Config click the VLAN Channel Config WAN VLAN Channel Config on the left navigation bar A screen is displayed as shown in Figure 4 6 4 VLAN DISPLAY This page allows management of vlan channels Auto Detect Enable Figure 4 6 4 VLAN DISPLAY This page allows management of wlan channels Auto Detect Enable A pimi 201 ptm 201 MIIL CH 1 ethi 7 ethnl D Figure 4 6 4 1 VLAN Channel Config Display Auto Detecting does not check the checkbox 38 CS RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in VLAN Displa
9. product s or circuit layout s described herein Maximum signal rate derived form IEEE Standard specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Ruby Tech does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose Make sure you follow in line with the environmental conditions to use this product RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info amp rubytech de Foreword VDSL2 Router solution Attention Be sure to read this manual carefully before using this product Especially Legal Disclaimer Statement of Conditions and Safty Warnings RubyTech VC 400RT is a management of the VDSL2 CPE router that leverages the extraordinary bandwidth promise of VDSL2 max 100Mbps symmetric technology the next step in the delivery of new high speed Internet applications in commercial environments Quick easy economical to install and maintain the VC 400RT works over existing copper wire infrastructure VC 400RT is a CPE Customer Premise Equipment device And compitable with the VS 840S
10. Apply Shaping To apply shaping on queue Click Apply for applying the changes Queue Scheduler Type Click CANCEL to exit from this page without saving the changes 82 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de 4 11 3 Class Config To classify the upstream traffic Click the Class Config link QoS Class Config on the left navigation bar A screen is displayed as shown in Figure 4 11 3 WAN Egress Classifier Configuration Configures classification entries in CPE device to be used in conjunction with other QoS entities Classifier Classifier Queue Outgoing Figure 4 11 3 Class Config The screen contains the following details Fields in Class Config Field Description Ha Selection tab for upstream downstream Classifier configuration Order This shows the order of the classification entry Classifier Interface This is a Packet Input Source for classified flow Outgoing DSCP This is the DSCP mark for next hop Action Selection option for deleting or modifying action on chosen classifier Delete Delete button for deleting selected queue When you click Add or Modify in the Classifier Config page a screen is displayed as shown in Figure 4 11 3 1 83 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de
11. No WAN Channel Type eeng WANIPO PTM VLAN 201 Bridge WANPPP1 PTM VLAN 201 PPPoE Figure C 2 WAN Setting 3 Please refer to the section 4 5 6 to config the wan type the user can configure the Dynamic IP Address Static IP Address PPPoE mode 99 RUBY 5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel 4 pimd 204 cl WAN TYPE static IP Address 7 m Static IP Address Address Version IF address assigned by your ISP Subnet Mask ISF Gateway Address Figure C 3 Config WAN Type Click Apply for applying the changes Click CANCEL to exit from this page without saving the changes Append VC 400LT VC 400RT Performance Table Test Environment Test Items Descriptions VDSL2 CO Router x 1 VC 400LT CO Router Operation System Windows XP SP3 Loop Simulator 24 AWG simulator card Test condition Descriptions Test Items Noise injection None 100 VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Compatibility Table VC 400LT VC 400RT The following shows the band profile and band plan compatibility table Band Profile List
12. The menu below includes the sub menus of QoS Settings Queue Config and Class Config Following are the options available under QoS as shown in Figure 4 11 QoS Settings Queue Config Class Contig Figure 4 11 QoS Options 79 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 11 1 QoS Settings To configure the Quality of Service QoS Settings click the QoS Settings link QoS QoS Settings on the left navigation bar A screen is displayed as shown in Figure 4 11 1 QoS Setting Quality of Serioa settings for previcing WAN unsrregm traffic nnertiratien in CPE Ave VAN made Qos C3 Enahle Disabili Upstream Qos C Enable Disabili C3 Enable nisabli S 21P Remarking O Enable Disable The defaut DECH Marking can be used to mark all the packets on WAH uplink that do mot match any Casshecon entries of o5 Upstream Default DSCP marking E T WAM Pert Rate Limiter DO PPA Session Acceleration Setting Erase o Diable PPA Segun Accelero PRA Sesckan Acceleration C Enable 2 Disable GELD QR AND Ge Figure 4 11 1 QoS Settings The screen contains the following details Fields in QoS Settings Field Description Informative Parameter to show current WAN mode being used in Active WAN mode ape Enable This selection will enable the QoS feature in VC 400RT system Upstream QoS Enable This selection w
13. Web Settings Software Firmware Upgrade Configuration Settings System Log SSL Certificate Reset Figure 4 3 System Setup 20 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 3 1 Host Name Config To configure the host name of VC 400RT you have to enter host and domain name Click the Host Name Config link System Host Name Config on the left navigation bar A screen is displayed as shown in Figure 4 3 1 ES Host name Host Name Config System Time Administrator Settings Web Settings Software Firmware Upgrade Configuration Settings Domain Name abc com Enter the host name for the CPE device and the domain name you want to configure Host name can be used in place of IP address Host Name labcEpe System Log o SS L Certificate ei u pply Can co Reset Figure 4 3 1 Host Name Config Fields in Host Name Config Description Enter the host name of the VDSL2 CPE This is used to address VDSL2 CPE by Host Name l l NN l using this name instead of typing the IP address Maximun Characters 60 Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 3 2 System Time You can set System Time by connecting to a Simple Network Time Protocol SNTP server allows the Modem to synchron
14. amp Communications www rubytech de info amp rubytech de Appena E Troubleshooting Diagnosing the Router s Indicators The router can be easily monitored through its comprehensive panel indicators These indicators assist the network manager in identifying problems the hub may encounter This section describes common problems you may encounter and possible solutions Cause Defective External power supply M P P nnn nnn enn ene nnn m Check the power plug by plugging in another that is functioning properly Check the power cord with another device Check the terminal block make sure to fasten the Solution power cord If these measures fail to resolve the problem have the unit power supply replaced by a qualified distributor Note Please refer to power status table to check power input status Section 3 3 S 3 Network interface ex a network adapter card on the attached device network cable Cause or switch port is defective AE EE EE E EE EE cl 2 1 Power off and re power on the VDSL2 router 2 2 Verify that the switch and attached device are power on 23 Be sure the cable is plugged into both the switch and
15. and proximity to other network devices that are to be connected Verify the following installation requirements e Power requirements DC 12V 1A e The router should be located in a cool dry place with at least 10cm 4in of space at the front and back for ventilation e Place the router away from direct sunlight heat sources or areas with a high amount of electromagnetic interference e Check if the network cables and connectors needed for installation are available e Do Not install phone lines strapped together with AC power lines or telephone office line with voice signal e Avoid installing this device with radio amplifying stations nearby or transformer stations nearby e Please note VC 400RT internal splitter it can pass through voice spectrum is OKHz 120KHz RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 2 3 General Rules Before making any connections to the router please note the following rules e Ethernet Port RJ 45 All network connections to the router Ethernet port must be made using Category 5 UTP or above for 100 Mbps Category 3 4 UTP for 10Mbps No more than 100 meters of cabling may be use between the MUX or HUB and an end node e VDSL2 Port RJ 11 All network connections to the RJ 11port must use 24 26 gauge with twisted pair phone wiring We do not recommend the use of the telephone line 28 gau
16. cable is typically used to connect the Ethernet device to the router A 10Base T cable often consists of four pairs of wires two of which are used for transmission The connector at the end of the 10Base T cable is referred to as an RJ 45 connector and it consists of eight pins The Ethernet standard uses pins 1 2 3 and 6 for data transmission purposes Table A 1 Table A 1 RJ 45 Ethernet Connector Pin Assignments Media Dependant Dependant interface cross interface Transmit Data l 1 TX RX Receive Data Unused 1 Figure A 1 Standard RJ 45 Unused repectacle connector Please make sure your connected cables are with same pin assignment as above table before deploying the cables into your network ES Wihite orange ES White Orange BH Grange EH Grange BS Vihitetsreen E Vinibesreen BH Blue BH Blue BD White Blue EH Vihite Blue EH Green EH Green BE Vinite Eirown BH Venibemirowm E n B Grown Figure A 2 Pin Assignments and Wiring for an RJ 45 Straight Through Cable BH White Orange ES Wn elcreen a 5 BH Orange BH Green BH WhaelGreen ES Whaelcrange E Due Eg Nhite Broawn E White Bue IB Brown BH Green BH Grange ES White Brown E Ge B brown EJ Wnr e Blue Figure A 3 Pin Assignments and Wiring for an RJ 45 Crossover Cable 95 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de A 2 Telephon
17. xDSL Status on the left navigation bar A screen is displayed as shown in Figure 4 5 1 rete E ee dcc ee eg EE E ng Dee ie er er XDSL Line Status Peoia Stade informers about vL nag curaret grita cue thormar ATUAC Syrien Wasia Infenration Hear End Far End verdi 10 E55 02 42 44 42 45 060 00 Supertuma het available YESS Vergas Mondes CM 90 049 3850 IT 28 EE EE e LOS Fallure a l LPR Failure 0 d Heen S SHOWTIME EN NCD Fallure Fische Marker VOR 19 Power Hanagement Hodie DEL GHT Ps 15 LCD Failure H H rela Ce Mou cene CR 1753 Lee Typ Pun BE Correction 240 SEE Forward Error Correction 0 LASTEST Mitra Seconda FECS L Fans date bpa God kipi Errored Secondi ES L D 1672 pedem wb Ven amp 2EM kien Serverely Errored Seconds SESeL d 116 Lee of Sigel Sacondn LOSS n 108 Dowesresm Upstream Unavailable Seconedef WAS L 2 ia Diesem z i HEC Error Line Aeration AT ZE opa core d Zeie Eug Rate Fare Chit LIS i Figure 4 5 1 xDSL Status 31 CS RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in xDSL Status Field Description ATU C System Vendor Displays the Vendor ID Version Number and the Serial Information Number of the ATU C DSLAM Displays the data rate and the maximum attainable data rate Displays the performance figures of the physi
18. 192 168 16 9 File favican ice is protected ur EI M NL MN EL P NL mm Figure 4 3 7 1 View System Log 27 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de For the ease of readability the log messages of different levels are using different colors For example all the debug messages are shown in green colored text Click Download to save the file in Host Computer Click Clear to clear the log from the system Click Refresh to get the recent log Click Back to go back to System Log page 4 3 8 SSL Certificate To install a SSL Certificate for SSL tunnel click the SSL Certificate link System SSL Certificate on the left navigation bar A screen is displayed as shown in Figure 4 3 8 SSL Certificate Copy and Paste your SSL Certificate in the text box This certificate is used for HTTPS access to CPE Figure 4 3 8 SSL Certificate Click Apply to install the entered certificate Click Cancel for cancel the installation of entered certificate 4 3 9 Reset To reboot the system click Reset link System Reset on the left navigation bar A screen is displayed as shown in Figure 4 3 9 Reset CPE device Host Name Config Svstem Ti In the event that the CPE device stops responding correctly or in some way stops functioning you can perform a reset To perform the tet ne re
19. 2 EU X VAN Statistics Statistics gt LAN KE The WAN Statistics gives the per interface statistics on the WAN side xDSL gt WAN gt EF TENERE Interface WAN Channel Connection Type Route gt ge ptm PTM VLAN 1 Fix IP 4128 1602641 0 E 5207 734760 0 0 NAT gt i w VD ep Figure 4 4 2 WAN Statistics The screen contains the following details Fields in WAN Statistics Field Description Interface Name of WAN Interface Connection Type Type of WAN Connection 30 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Networking amp Communications www rubytech de info rubytech de Fields in WAN Statistics cont d Description Transmit Counters for WAN interface Total packets transmitted from this interface Total bytes transmitted form this interface Total Errorneous packets transmitted on this interface Total Dropped packets transmitted on this interface 4 5 Select xDSL You can view the xDSL link on the left navigation bar of the CPE Home page This web page is available only on DSL platforms Select the xDSL The menu below includes the sub menus of XDSL Status A screen is displayed as shown in Figure 4 5 xDSL Status Figure 4 5 Select xDSL Note These options help to monitor and configure the DSL physical parameters in the device 4 5 1 xDSL Status To view the xDSL Status click the xDSL Status link xDSL gt
20. 2 IPv6 Firewall Setting To enable or disable the firewall click the IPV6 Firewall Setting link Firewall IPv6 Firewall Setting on the left navigation bar A screen is displayed as shown in Figure 4 9 2 66 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 QR Deutschland GmbH bein iid D Communications Nun LEE Prim m 2 SE IPv6 Firewall Settings IPv6 Firewall Settings You can configure IPv6 firewall settings You can configure IPv6 firewall settings Firewall Mode CPE policy 1 Rules to block fca0 7 in forwarding path GE 2 Rules to allow only active prefix from LAN to WAN and from WAN to LAN 1 No firewall rules 3 Rule to block everything else e g Invalid prefix expired prefix Firewall Mode go ve vm ee mp mm ee ee oe we we ew ww ww ww ww ow c ow ow ow ow o ow ow ow vm vm o ow ow ow ow ow a wg ww mm ow ow ow en IPv6 Firewall Settings IPv6 Firewall Settings You can configure IPv6 firewall settings You can configure IPv6 firewall settings EPUM MUR E V Firewall Mode Low i 1 Default policy is DROP EES See 2 Allow following outbound tcp traffics 1 Allow all outbound and pinhole defined inbound traffic telnet 23 ftp 21 http 80 https 443 smtp 25 pop3 110 imaps 993 ntp 123 2 Allow allow inbound IPsec AH 50 3 Allow outbound icmpv6 traffic 3 Allow allow inbound IPsec ESP 51 4 Allow only related established inbound traffic that is initiated by
21. 8Ports VDSL2 IP DSLAM and VC 400LT VDSL2 CO Router RubyTech VC 400RT will allow operators worldwide to compete with cable andsatellite operators by offering services such as HDTV VOD videoconferencing high speed Internet access and advanced voice services including VolP over a standard copper telephone cable RubyTech VC 400RT is seen by many operators as an ideal accompaniment to a FTTP rollout where for instance fiber optic is supplied direct to an apartment block and from there copper cable is used to supply residents with high speed VDSL2 Caution RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Networking amp Communications www rubytech de info rubytech de Safety Warnings For your safety be sure to read and follow all warning notices and instructions before using the device DO NOT open the device or unit Opening or removing covers can expose you to dangerous high voltage points or other risks ONLY qualified service personnel can service the device Please contact your vendor for further information Use ONLY the dedicated power supply for your device Connect the power to the right supply voltage 110V AC used for North America and 230V AC used for Europe VC 400RT support 12 VDC power input Place connecting cables carefully so that no one will step on them or stumble over them DO NOT allow anything to rest on the power cord and do NOT locate the product where anyo
22. 9 5 Parental Control You can block access based on MAC addresses and Time of Day to certain client PCs on the LAN MAC Address Control Disable Deny All Permit All nl MAC Address Control List Date Time Select MAC Address Begi d Tue Thu hh mm Disable v a a BE EI IB ET I Figure 4 9 5 Parental Control Configuration The screen contains the following details Fields in Parental Control Field Description Oa To disable deny all permit all MAC address control feature MAC Address Control List Policy To specify whether the particular MAC address is disabled denied or permitted MAC Address To assign the controlled MAC address for local machine To select the day s and time slot when the policy has to be applied on the MAC Date Time Select address provided The Begin time entered should not be later than the End time and should be in the 24 hour format hh mm Click Add at any time during configuration to add the specified MAC address entry in the table 71 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 9 6 Application Server Settings To configure the Application Server Settings click the Application
23. Interface This is used to select upstream downstream classifier Disable acceleration This is used to disable acceleration for this classifier This is the Queue Identifier to be associated with this classifier rule This Queue Name m MM u is presented in dropdown for associating with this classifier entry Ingress Interface Packet Input Source for classified flow u Type of Classifier Multi Field Classifier MFC or DSCP or 802 1p Classifier Type T ased 85 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Click Apply for applying the changes Click CANCEL to exit from this page without saving the changes 4 12 Multicast You can view Multicast on the left navigation bar of the VC 400RT CPE homepage The menu below includes the sub menus of Proxy Settings Snooping Settings and Advanced Settings Following are the options available under Multicast as shown in Figure 4 12 Multicast gt Proxy Settings Snooping Settings Advanced Settings Figure 4 12 Multicast Options 4 12 1 Proxy Settings To configure the Multicast proxy settings in CPE click the Proxy Settings link Multicast gt Proxy Settings on the left navigation bar A screen is displayed as shown in Figure 4 12 1 Proxy This page allows the user to configure the CPE to provide multicast proxy functionality Enable IGMP Proxy ull Enable ML
24. M Cable Length DS Cable Length US Mbps US Mbps meters Mbps meters Mbps as 9495 2516 18 esea ac 4 es se wm 750 gs mm 3950 146 120 mn ao 102 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Profile 12A Annex B 998 M2x B Profile 12B Annex A M1_EU32 Cable Length DS Cable Length meters IMS Mbps meters US Mbps Mbps Pte 8585 mn ae asya men Profile 12B Annex B 997 Mic A 7 Profile 12B Annex B 998 M2x A Cable Length DS Cable Length meters a Mbps meters a ad Mbps Pie ear asas 18 osea 9050 Profile 12B Annex A M9 EU64 Profile 12B Annex B 998 M1x B Cable Length DS Cable Length US Mbps US Mbps meters Mbps meters Mbps as sss aet 18 esoe 3516 Cable Length DS Cable Length US Mbps US Mbps meters Mbps meters Fis 8555 3830 as esea am Mbps 103 e RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Profile 12B Annex B 998 M2x NUSO Profile 17A Annex A M1_EU32 Cable Length Cable Length US Mbps US Mbps meters Mbps 9079 3x9 4854 08 mm 2559 om meters Mbps er To mn ew B ams Pag TA zn amo me zm w
25. SNTP Backup NTP Server optional Server Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes Note Static Routing functionality is used to define the connected Gateway between the LAN and WAN For example If we want to activate the Network Time Protocol NTP service and we have to define the Gateway connected to NTP server in the WAN Please refer to static routing for your reference 4 3 3 Administrator Settings To change the password for the administrator click the Administrator Settings link System gt AdministratorSettings in the left navigation bar A screen is displayed as shown in Figure 4 3 3 This page allows the user to change the login password Administrator Settings VW t t t Host Name Config Set a password to restrict management access to CPE device System Time Disable Administrator Administrator Settings Password O Web Settings Select user admin v Software Firmware Upgrade Current Password Configuration Setti fig nos Password password can be 3 16 Characters without white space System Log SSL Certificate Re type passwor Reset Enable account Statistics gt Remote V eb access enable GL ID QUAD Ge Figure 4 3 3 Administrator Settings 22 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech
26. Server Settings link Firewall gt Application Server Settings on the left navigation bar A screen is displayed as shown in Figure 4 9 6 Application Server Settings Application layer protocol services like Web server Telnet server TFTP server FTP Server and SNMP can be enabled disabled from this Https Web Server Accept from WAN Port Http Web Server Accept from WAN Port Accept from LAN Telnet Server Accept from WAN Port 23 Accept from LAN TFTP Server Accept from WAN Port Accept from LAN FTP Server Accept from WAN Port 21 Accept from LAN SNMP Accept from WAN Figure 4 9 6 Application Server Setting The screen contains the following details Fields in Application Servers Settings Description Web Server settings Web The acceptance from WAN Server The Port Number The acceptance from LAN TFTP Server Settings TETP The acceptance from WAN Server The Port number The acceptance from LAN FTP Server Settings ETE The acceptance from WAN Server The Port number The acceptance from LAN 72 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Click Apply for committing the App Server settings Click Cancel to exit from this page without saving the changes 4 9 7 Access Control List ACL To configure the access control list click the ACL link Firewall ACL on the left navig
27. above outbound traffic 5 Rest all are dropped 4 Allow allow inbound IKE 500 5 Allow related established inbound traffic that is initiated by above outbound traffic Figure 4 9 2 IPv6 Firewall Setting The screen contains the following details Fields in UPnP Settings Field Description Click APPLY for committing the desired action Click CANCEL to exit from this page without saving the changes 4 9 3 Packet Filtering To enable Packet Filtering click the Packet Filtering link Firewall Packet Filtering on the left navigation bar A screen is displayed as shown in Figure 4 9 3 Packet Filtering Configure packet filter rule for denying the packets conforming to it C Enable Packet Filter Source Sa rce Destination IP IP Destination Port Figure 4 9 3 Packet Filtering 67 VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in Packet Filtering Field Description RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de IPV4 IPv6 Choose the appropriate tab to configure Filter IP Address range of the local machine under VC 400RT Source IP ee Destination IP IP address of the destination Filter protocol TCP or UDP Egress Interface Output interface of the packet Enable To provide more IP Addresses of the WAN interface Delete All To delete all the packet filtering ru
28. allows configurability of IPv4 and or IPv6 stack on per WAN interface 44 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Fields in PPPoE WAN WAN IPv6 Configuration Description This option allows to select following modes of IPv6 configuration Configuration Modes Stateful DHCPv6 IA_NA and IA PD SLAAC Address Configuration with DHCPv6 IA PD IANA option represents IPv6 address and parameters related to the same being IANA ID accepted by DHCPv 6 clients IANA is the Identity Association for Non Temporary Addresses option This Identifier to be configured when Stateful DHCPv6 configuration mode is selected This parameter is called Site Level Aggregation Identifier This identifier is used to configure the subnet for DHCPv6 client configuration This option allows to configure default route for relevant WAN mode of this WAN Default WAN l connection Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 6 5 4 PPPoA The PPP over ATM PPPoA mode is valid only for ATM based WAN To configure the WAN interface to use PPPoA select the option PPPoA option A screen is displayed as shown in Figure 4 6 5 6 45 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Network
29. dynamic 6rd tunnel through DHCP option or static Modes tunnel configuration Static Parameters 6Rd Prefix 6RD Prefix string 6RD BR IP 6RD Broder Relay s IPv4 address Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 4 14 3 DS Lite Configuration The VC 400RT supports DS Lite configuration mechanism To configure the Ds Lite configuration click the DS Lite configuration link IPv6 DS Lite Configuration on the left navigation bar A screen is displayed as shown in Figure 4 14 3 DS Lite Configuration Because of IPv4 address exhaustion Dual Stack Lite DS Lite was designed to let an Internet service provider omit the deployment of any IPv4 address to the customer s Customer premises equipment CPE Instead only global IPv6 addresses are provided Note To configure DS Lite on a V AN connection IPv6 must be enabled at IPv6 Setting page and native IPv6 must be enabled on that WAN connection at WAN Setting page General Settings Enable DS Lite tunnel L1 WAN Interface select interface x Configuration Modes Static DS Lite MTU foptional Static Parameters DS Lite Remote IPv6 address DS Lite tunnel IP address IPv4 Subnet Mask Lw406 Port Range Valid 0 to 65535 Ex 40000 4nnnn 410 41000 WAN interface Configuration Mode Remote IPv6 address Tunnel IP IPv4
30. equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver The equipment and the receiver should be connected to outlets on separate circuits Po Iw x Consult the dealer or an experienced radio television technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment If this telephone equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the proper functioning of
31. range of IP Type addresses The available options are Drop Reject and Accept Click Apply at any time during configuration to for adding the packet filtering rule Click CANCEL to exit from this page without saving the changes 4 9 4 URL Filtering Using URL Filtering the user can block the access to specific URLs to the web users by adding them to the list in the URL Blocking web page To configure the URL Filtering click the URL Filtering link Firewall URL Filtering on the left navigation bar A screen is displayed as shown in Figure 4 9 4 URL Blocking This web page allows you to Block URL s on the CPE device N Domain Nam Select Nothing is blocked INED LE EL Figure 4 9 4 URL Blocking 70 e RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in URL Blocking Field Description Domain URL of the domain that needs to be blocked For example Name www google com tw Select Select this option to remove the URL entry from blocked list Click Add for adding a new URL filtering entry Click Delete for deleting the existing URL filtering entry 4 9 5 Parental Control To configure the Parental Control click the Parental Control link Firewall Parental Control on the left navigation bar A screen is displayed as shown in Figure 4
32. rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Username Password Figure 4 1 Login Password 4 1 1 Home After successful login using the username admin the home page of VC 400RT is loaded in web browser for VC 400RT Uesr can aslo click the Home on the left navigation bar The home page displays the information screen as shown in Figure 4 1 1 System Statistics Version Information xDSL gt Software Version B 1 WAN DSL Firmware version 5 4 8 0 0 6 5 4 4 4 0 1 5 4 8 0 0 6 5 4 4 4 0 1 TAN Route Connected Standard Firewall gt Modem Status SILENT NAT QoS gt Wan Mode VDSL PTM Multicast gt Link Status UNCONFIGURED IPsec IP Address UNDEFINED IPv gt Connection Type PPPOE Diagnostics DNS Server 168 95 1 1 Pe 168 95 1 1 Quick Setup Home IP Address 192 168 16 207 Logout DHCP Mode Disabled Ethernet PHY Port Status PORT 1 Link Dawn PORT 2 Link Down PORT 3 Link Up 100Mb s Full Duplex PORT 4 Link Up 1000Mb s Full Duplex Figure 4 1 1 Home Information 15 RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in Home page Field Description Version Information Software Version Shows the current version of VC 400RT Software loaded on the device xDSL Information Connected The DSL Standard
33. selected from dropdown ESPHash ESP Hash algorithm to be selected from dropdown Number of retries in case key exchange fails Click Apply for applying the configured IPsec tunnel Click CANCEL to exit from this page without saving the changes 4 14 IPv6 When you click IPv6 link on the left navigation bar of the VC 400RT CPE homepage The menu below includes the sub menus of IPv6 Setting 6RD Configuration and DS Lite Configuration The following options are available as shown in Figure 4 14 IPvo Setting 6RD Configuration DS Lite Configuration Figure 4 14 IPV6 Options 90 RUBY TECH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 14 1 IPv6 Setting To enable or disable IPv6 functionality in CPE click the IPv6 Setting link on the left navigation bar A screen is displayed as shown in Figure 4 14 1 By default IPv6 is not enabled IPv6 Setting This web page alows ta enable or disable the IPv6 capabilities on the CPE device HOTE The IPv6 related settings on other web pages will be effective only if IPv6 is enabled here Enable Disable Figure 4 14 1 IPv6 Setting The system wide IPv6 feature can be enabled or disabled through this web page Select appropriate control and click Apply button for making the change effective in CPE All other IPv6 features in CPE would be in effect only when this gl
34. upstream downstream Queue configuration Sek Precedence of Queue Lower values denote higher priority Precedence i l This is the queue scheduling algorithm used for the queue The supported Scheduler queue Algorithm scheduling algorithms are SP Strict Priority or WFQ Weighted Fair Queuing Committed Shaping Rate Committed or Guaranteed Shaping Rate in Kbps or Percentage Enable This provides the status of queue entry Enabled or Disabled This button is used to add a new queue Modify This button is used to modify the selected queue entry 81 gt gt RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de When you click Add button in the Port Triggering page a screen is displayed as shown in Figure 4 11 2 1 VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Add Modify a WAN Egress Queue Entry Queue Name Queue Interface WAN se Queue Precedence Queue Drop Type RED w RED Min Threshold o RED Max Drop Probability P Queue Scheduler Type Queue Weight Apply Shaping L Enable C Figure 4 11 2 1 Add Modify a Queue Entry The screen contains the following details Fields in Add Modify a Queue Entry Field Description Name or Identifier of Queue Queue Precedence of Queue Lower values denote higher priority RED Min Threshold RED Threshold Value applicable for RED Drop algo Queue scheduling Algorithm SP or WFQ
35. which is being used currently between DSL CPE and Standard DSLAM Default WAN Connection Current WAN mode being used in CPE IP Address Shows the IP address of default WAN connection Shows the primary and secondary DNS servers configured in default WAN DNS Server connection LAN information Shows the IP address of LAN interface of CPE This IP address to be used IP Address for accessing the CPE device from LAN side e g Web Ul TELNET or UPnP sessions Ethernet PHY Port Status 4 1 2 Quick Setup The Quick Setup is located on the left side of the screen Quick Setup provides a simple and easy step for applying minimal configuration to CPE device for making it ready to use The CPE Quick Setup window is displayed as shown in Figure 4 1 2 Click on Quick Setup to view and configure the following connections 16 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de Quick Configuration of default WAN connection ta Service Provider s network WAN Setup Default WAN Connection Setup Channel Vlan d 201 Connection Type PPPoE v Username Password Figure 4 1 2 Quick Setup WAN Setup When the user clicks on Quick Setup the WAN Setup tab is displayed as shown in Figure 4 1 2 1 The WAN Setupenables the user to configure the default WAN connection The user has to supply fields and the CPE device will take all necessar
36. wiring sharing similar electrical characteristics can be bundled together You should separate input wiring from output wiring We recommend that you mark all equipment in the wiring system EISES Configure the VC 400RT Via Web Browser The VC 400RT provides a built in HTML based management interface that allow user configure the VC 400RT via Internet Browser Best viewed at using the Chrome or Firefox In order to use the web browser to configure the device you may need to allow e Web browser pop up windows from your device Web pop up blocking is enabled by default in windows XP SP2 or above e Java Scripts Enabled by default e Java permissions Enabled by default Launch your web browser and input the IP address 192 168 16 249 VC 400LT or 192 168 16 254 VC 400RT in the Web page This section explains how to configure the router section of the VC 400RT using its web based configuration The part of the circuitry as well as the router configuration menu has been ported from that of the reference kit to the VC 400RT reference board As for the menu there are only a few differences e The ptm port now is the port to the VDSL2 side The port on the LAN is brO It supports four Ethernet connections 4 1 Login The default username is admin and password is admin too The password is changeable in Administrator Settings 14 RUBY Deutschland GmbH Networking amp Communications www
37. www rubytech de info rubytech de Click Apply at any time during configuration to save the information that you have VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 entered Click Cancel to exit from this page without saving the changes 4 6 5 3 PPPoE To configure the WAN interface to use PPPoE choose the option PPPoE A screen is displayed as shown in Figure 4 6 5 5 WAN The OPE device can be connected ta your sevice provider in amy of the folowing wars Attached Channel WAH TYRE 1 ptmo 201 PPPoE E User hame Fagsward Please retype your password Service Hamit Access Concentrator tame Relay LAN gie PPPOE section oO MTU pppoa 1400 1492 papee 1400 1500 1422 PPP Option ap anna Ka Address Version P e ev WAN IPv6 Configuration Configuration Modes DUID Type IANA ID H SLA ID T Statofui DHGPU A A ana tA PD Typi 1 LLT Lirik Lanei Time baf tri D Rapid Commiut L1 el Default WAN m GEL E QE AND QR UN Figure 4 6 5 5 WAN PPPoE creation The screen contains the following details Fields in PPPoE WAN Field Description To enter a username for PPPoE session used for authentication in User Name B RAS Please retype your password Access Concentrator Name To enter the same password again to reconfirm PPP Access concentrator Name optional Relay LAN site PPPoE Session This feature allows to enable disable a PPPoE relay session Address Version This option
38. you must set up a gateway to connect different network segment Regarding how to configure a default gateway at switch bridged mode for crossing various network segments please refer to the section 4 8 1 for your reference Answer Configuration gateway example from static routing Destination LAN IP 0 0 0 0 Subnet Mask 0 0 0 0 Gateway 255 255 255 0 Note Static Routing functionality is used to define the connected Gateway between the LAN and WAN VC 400RT support the ADSL backward compatible therefore the VC 400RT can connect to ADSL2 IP DSLAM Annex B Answer lf you forgot your password you must reset your router Unfortunately this process will change all your settings back to the factory defaults To reset the router locate the reset on the rear panel of the unit With the router powered on use a paperclip to hold the en button down for over 5 seconds Release the button and the router will go through its reboot process The default ip is 192 168 16 254 When logging in the default username and password both are admin a M e M M e M E M M mn a e e M e ann M M ann an ann an ann M M M M
39. 16 49285 192 168 16 16 2382 Figure 4 10 2 The screen contains the following details Fields in Virtual Server Page Field Description Enable Virtual Server Port Type Add Dynamic z E Delete e Dynamic em ET Configured Application Name for Virtual Server rule Hemote IP Remote IP address of Virtual Server rule G Sm Private Port ending range for single port the start and end both are same Public Start l Public Port starting range Enabled To enable the specified entry of the virtual server Click Add to add a Virtual Server entry When you click Add button in the Virtual Server page a screen opens with a new web page as shown in Figure 4 10 2 1 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Configure Virtual Server Configure the CPE device as a Virtual Server so that external service requests can be redirected to the internal Servers such as FTP or WEB Application Name Select an application Select One v Custom application Protocol Private 1P e Jl ie Remote IP d o i o f 0 optional Public Port Range Private Port Range o FH Enable WAN Interface WANPPP1 v Help Figure 4 10 2 1 Virtual Server Add The screen contains the following details Fields in Virtual Server Add Field Des
40. 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 3 1 Front Panel The figure shows the front panel Figure 3 1 Q RUBY PWR E1 E2 E3 E4 LINK CH En VC 400RT an vet Figure 3 1 Front Panel VC 400RT 3 2 Front Indicators The router has Six LED indicators The following Table shows the description Table 3 1 Color Status Descriptions On Steady Lights to indicate that the VDSL2 router had power The device is not ready or has malfunctioned On Steady The device has a good Ethernet connection Ethernet The device is sending or receiving data LED The LAN is not connected or has malfunctioned On Steady The Internet or network connection is up LINK VDSL2 The device is sending or receiving data LED Slow o mE The Internet or network connection is down Blinking Table 3 1 LED Indicators Description and Operation Note It is normal for the connection between two Routers to take up to 3 minutes due to VC 400LT A to establish a link mechanism in auto negotiation with detects and calculates CO and CPE both PBO and PSD level noise levels and other arguments for getting a better connection 12 RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 3 3 Rear Panel The following figure shows the rear panel Figure 3 2
41. 9 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 2 Select the Menu Level There is an easy Setup for end users at the setup of VC 400RT with SYSTEM Statistics xDSL WAN LAN Route FIREWALL NAT QoS Multicast Ipsec IPv6 Diagonstics Quick Setup Home Logout for more detail configurations VD5L2 CPE Routen System otatistics F i Viena lndormation xDSL afue Verum WAM DAL Frane vers 4 8 0 0 6 344401 34 20 04 344401 LAM ST bnftargnabinn Route Connected Standard Firewall i Hadar Ser SE REQUEST MATE Default WAM Connection Qoz Wan Made V SL PTM Multicast F Link Status UNDEFINED IP Address UNDEF DED liii Donnera Teo irage Dhs Sar a Diagnostics LAM information DD Addreda ESA Ai Kik Quick Setup Home DHCP Mode Disables Logs Sk S1 s PHY Pert Stalin f POSTE Link Down POET Z Link Dena PORT 3 Link Un on Rall Dunt PORT 4 Ling Ws LOM Fol Duplex K las Figure 4 2 Select the Menu Level VC 400RT 4 3 Select SYSTEM Select the SYSTEM The menu below will be used frequently It includes the sub menus of Host Name Config System Time Administrator Settings Web Settings Software Firmware Upgrade System Log SSL Certificate and Reset A screen is displayed as shown in Figure 4 3 Host Name Config System Time Administrator Settings
42. AN Settings on the left navigation bar In case the Secondary level subnet Range checkbox is checked some additional data and options will be on display A screen is displayed DHCP Server mode as shown in Figure 4 7 2 LAM Settings You can configure LAN sattings of CPE Device such as LAN TP Address and DHCP configuration IP Address TA Subnet Mask MAC Adina Secondary level subnet Range IP Address Reservation Chck Here Figure 4 7 2 LAN Settings DHCP Server 55 RUBY TECH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in LAN Settings Field Description IP Address Used to enter the LAN interface IP Address of CPE device MAC Address of LAN bridge device It can be overridden by specifying the user MAC Address l supplied MAC address here Secondary IP Address This is to enter the secondary IP address To choose the mode of DHCP in VC 400RT The options available are Disable Server and Relay Agent The default value is Disable If DHCP Mode is set to Server there are some additional options available which are shown in Figure 4 7 2 IP Pool Starting Address To enter the starting IP Address of the DHCP DHCP Mode server pool IP Pool Ending Address To enter the ending IP Address of the DHCP server pool Lease Time To specify the lease period for DHCP alloca
43. ATM PVC Scheduling Supports ATM Total Upstream Priority Queues Support uPnP PPPoE PPPoATM IPvA IPv6 NAT NAPT Support static routing for IPv4 and IPv6 forwarding so so Support Firewall functions contains Packet filtering DMZ Mac Address ased filtering Parental Control Application based filtering Support DHCP Server DHCP Relay DHCP Client DHCPv6 Client DHCPv6 Server DNS DNS Proxy or Relay DNSv6 Proxy or Relay NTP Client HTTP1 1 server Support Multicast IP table IGMP v3 Proxy and Snooping Support IEEE 802 1p VLAN Priority and mapping to DSCP Supports HTTP HTTPS SSL web management Support remote management and monitor Support configuration backup and restore Provides surge protection for Line port Supports jumbo frame up to 10k bytes Supports IEEE 802 1w RSTP Support Router amp Switch Bridged mode selection Supports 8 queue MFC DSCP both type QoS 999999999 Note 1 Features and specifications in this manual are subject to change without prior notice 2 Firmware upgradeable for future enhancement 97 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Product Specification 4 x RJ 45 10 100 1000Mbps Ethernet port 1 x RJ 11 Terminal Block connector for VDSL2 line port 1 x RJ 11 connector for POTS ISDN device 1 x console port RS232C 115200bps Physical Interface 1 x Power LED LE
44. Band Plan List 0 VDSL2 Profle8a 1 VDSU2Prfleb 2 VDSUZ2Prfle o 3 uereg 4 VDSU2Prlei2a 5 VDSU2Prflei2b 6 VDSU2Prflei7a 8 VDSU2Prfle7b Annex C 8K 1M1 Annex B 998E17 M2x A Band Profile Band Plan 0 8a Performance Table Tip US Up Stream DS Down Stream Annex B 998E17 M2x NUSO The performance data below is for reference only the actual data rate will vary depending on the quality of the copper wire and environment factors e e e em e e mm mm mm e mm mm mm mm mm mm mm e e e RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Profile 8A Annex B 997 M2x M Profile 8B Annex B 997 M2x A Cable Length Cable Length US Mbps US Mbps meters Mbps te sesa 2798 ww xo fan meters Mbps as sooi 2854 e Ian am e 2080 067 Profile 8B Annex B 997 M2x M Profile 8C Annex B 998 M2x M Cable Length DS Cable Length US Mbps US Mbps meters Mbps meters Mbps Pie seas enio e asas oar Profile 8D Annex B 997 M2x A Profile 12A Annex AM 9 EU64 Cable Length DS Cable Length meters US Mbps Mbps meters US Mbps Mbps a so 2854 ae esas ayi 31e se asi 9 nl ss 19 209 05 m anos ar Profile 12A Annex B 998 M1 x B Profile 12A Annex B 998 M2x
45. Config on the left navigation bar A screen is displayed as shown in Figure 4 6 3 WAN Channel Configuration This page allows management of layer 2 channels for WAN Auto Detect Enable Figure 4 6 3 WAN Channel Configuration This page allows management of layer 2 channels for WAN Auto Detect Enable O ATM Channel Name VPUNCI Encapsulation Mode Link type ATM QoS vcc channel 1 0 35 LLC SNAP rfc2684 eoa nas Help Figure 4 6 3 1 WAN Channel Config Auto Detecting does not check the checkbox 36 RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in WAN Channel Config Description The ATM based WAN channels are configured through the ATM tab Auto Detect Enable To enable Auto Detect VPI VCI Virtual Path Identifier and Virtual Channel Identifier Shows AAL5 Link type for ATM VCC values such as EoATM IPoATM Link type 2 PPPoATM IF Name ATM Channel interface name in system When you click Add inside the WAN Channel ATM tab a screen is displayed as shown in Figure 4 6 3 2 WAN ATM VCC Creation VC Channel Name D 1 VPI VCI 0 32 0 255 32 65535 Encapsulation Mode Link type QoS Mode Peak Cell Rate P cells sec Cell Delay Variation jitters Add Figure 4 6 3 2 WAN Channel Config ATM VCC Creation 37 RUBY
46. D Indicators 4 x Link Active Status for Ethernet port 1 x Link LED for VDSL2 port Typical Power B Consumption EMI Compliant FCC Class B EMS EMS Compliant CE mark ClassB B Storage Temperature 20 C 70 C 4 F 158 F RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Appendage Router Mode select This appendix describes how to select the router mode The VC 400RT default mode is switch bridged mode please refer to the following steps to select the router mode or switch mode Select the Router mode 1 To configure the router mode settings click the LAN Settings link LAN gt LAN Settings on the left navigation bar Then select the Server atthe DHCP Mode and click Apply at any time during configuration to save the information that you have entered A screen is displayed as shown in Figure C 1 DHCP Server IP Pool Starting Address 192 168 14 SE IP Pool Ending Address 182 i 4 68 i 4 i 254 Lease Time Half hour v Local Domain Name dsigw lantig com optional IP Address Reservation Click Here GELS Gla GELANG Figure C 1 DHCP Mode Server 2 Click the WAN Setting link WAN Setting WAN on the left navigation bar to specify the WAN setting Please cancel the check of the Auto Detect Enable and Add to config the wan type WAN Setting Auto Detect Enable EC 1
47. D Proxy A WAN TS Figure 4 12 1 IGMP Proxy The screen contains the following details Fields in IGMP Proxy Description Enable IGMP E Enable or Disable the IGMPv3 IGMPv2 Proxy functionality Select one of the WAN interfaces from the drop down menu on which Multicast Proxy functionality to be enabled 86 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 4 12 2 Snooping Settings To configure the Multicast Snooping settings click the Snooping Settings link Multicast gt Snooping Settings on the left navigation bar A screen is displayed as shown in Figure 4 12 2 Snooping This page allaws the user to configure the CPE to provide multicast snooping functionality Enable IGMP MLD Snooping A Figure 4 12 2 IGMP Snooping The screen contains the following details Fields in Fields in Snooping Field Description E REE Enable or Disable the IGMPv3 IGMPv2 Snooping functionality Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 4 12 3 Advanced Settings To configure the advanced settings on Multicast features click the Advance
48. E WARRANTY STICKER AS If Removed SHOWN OR THE WARRANTY IS VOID 2 NARRANTY VOID IF USE COMMERCIAL GRADE POWER ADAPTER IS USED AT HARSH ENVIRONMENTS 113
49. Figure 4 14 3 DS Lite Configuration 02 CS RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in DS Lite Configuration Field Description General Settings Enable DS Lite tunnel To enable disable DS Lite functionality in CPE Modes to configure DS Lite tunnel on a WAN interface Configuration Modes Currently Static Dynamic DHCPv6 option 64 and Lw406 DS Lite modes are supported Static Parameters IPv6 address of the remote tunnel endpoint DS Lite Remote IPv6 address When you select Dynamic mode this field is disabled Subnet Mask IPv4 Address subnet mask Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 4 15 Diagnostics When you click Diagnostics link on the left navigation bar of the VC 400RT CPE homepage The menu below includes the sub menus of Diagnostic Test Suite The following options are available under Diagnostics as shown in Figure 4 15 Diagnostics gt Figure 4 15 Diagnostics Options 93 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 15 1 Diagnostic Test Suite To configure the Diagnostic Test Suite settings click the Diag
50. N Setting Auto Detect Enable WAN Setting Auto Detect Enable Default WANIPO PTM VLAN None Bridge Figure 4 6 5 1 WAN Setting The VC 400RT can support up to maximum 16 WAN connections in system When a hardware based QoS is enabled in system it limits the number of VCCs to 8 only for ATM based WAN For creating a new WAN connection click Add in the WAN setting page Please follow the rest of the steps for creating the WAN connection 40 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info amp rubytech de The last column named DEFAULT GATEWAY allows to select the WAN for relevant WAN mode setting in WAN setting web page When the user clicks any of the radio button he will be asked to confirm the same If the user clicks Apply the default gateway will be configured on the selected WAN connection otherwise the changes will not be applied The screen contains the following details Fields in WAN Settings Field Description Auto Detect Enable To enable Auto Detect WAN Channel Provides information of layer 2 WAN channel configured Default VolP This option is present in only IAD models where VolP is supported this Interface is default interface for VolP packets When you click Add button in WAN Settings web page a screen is displayed as shown in Figure 4 6 5 2 WAN The CPE device can be connected to your
51. OUTER nnn tnnc 2d HABDWATRETDNISTAEDATION EE 2 2 PRE INSTALLATION REQUIREMENTS assssssisseeeseennniniuenetannikkkntnn annn A nkkan aAA A AEEA EEEEARAAEEEEEEEER AA EEEEEEEERREEEEEEEE EEEE EEEE EE aeai E een EEEE E 2 4 CONNECTING THE yO TE Rei ea a seen CO CONNECTING THE RJ 11 RJ 45 PORTS ee ee 2 OND EZ AP PUIG ATION curona iee suc ee EE GAPS HARDWARE DESCHIDTION nnnc C Nice uiis T 3 2 FRONT INDICATORS SS FEAR FANE eege GRARPTERM CONFIGURE THE VC 400RT VIA WEB BROWSER BNO GAIN M d TT TOI LEE el Ner DUCK SE D o EE aviez MANI RT AS SELECT SYS EM diete 4 331 HOSEN UAE e DEE A SEA ISI NE EE 4 9 9 Administrator Settings so cs ssuce cseanentmuisnadeesansevediexcmacioesenetndaedenncanvbseentsegadivewustencedeenecaieapeacnendeneoacectbameoteescee a SA VO UUM MR E TTD reelle serie 4 3 5 Solare Firmware Upgrade oe aues acide iuit tanni ee een 4 9 0 GOMUGUI ATION SEINS sson arora aaie E E a a E a AEE a N SOTT E Le ME e e Ben e e BR EE E WEE Re NE EE e D 45 E WE E RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info ru
52. Open Port Start Open Port Start range Open Protocol to be opened from external input TCP UDP or Protocol TCP UDP Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 78 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 10 4 DMZ To configure the DMZ Demilitarized Zone click the DMZ link NAT gt DMZ on the left navigation bar Upon configuration of DMZ all traffic sent towards RG would be unconditionally forwarded to DMZ Lan Host A screen is displayed as shown in Figure 4 10 4 DMZ Demilitarized Zone If you have a local client PC that cannot run an Internet application properly fram behind the NAT firewall you can open the dent up to unrestricted two way Internet access by defining a virtual DMZ Host Enable a IP Address of Virtual DMZ Host 132 hs h a Apply Apply ance Cancel Figure 4 10 4 DMZ Demilitarized Zone The screen contains the following details Fields in DMZ Description To enable or disable the DMZ setting of VC 400RT CPE Select the check box to enable Click Apply for applying the configured DMZ Click Cancel to exit from this page without saving the changes 4 11 QoS You can view QoS on the left navigation bar of the VC 400RT CPE homepage
53. Password Configure Figure 4 1 2 3 WAN setup PPPoE The screen contains the following details Fields in WAN setup PPPoE Field Description Channel Vlanld Specify VLAN Id Username Enter a valid Username 18 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Click Configure to configure the selected WAN connection setup Quick Configuration of default WAN connection to Service Provider s network Default WAN Connection Setup Channel VlanId 201 Connection Type IP address Subnet Mask Gateway Configure M Help Figure 4 1 2 4 WAN setup Static IP The screen contains the following details Fields in WAN setup Static IP Field Description Channel Vlanld Specify VLAN ld Specify the Gateway address of the VC 400RT CPE s WAN Click Configure to configure the selected WAN connection setup IP Address specify the IP Address of VC 400RT CPE s WAN link When WAN mode is other than ATM the corresponding web pages will be available in WAN setup Those web pages will not ask user for fields like ATM VCC etc eee ee ee ew em ew ew ew ew ew em em ew ew em ew ew em em ew zz em em ew ew zz zz zz em zz em ew ew 2 2 2 ew 2 zz ew zz zz zz zz 2 2 em 2 2 2 2 2 2 2 ew 2 2 em 2 2 em ew ew em em zz em zz ew em zz zz zz em 2 2 2 zz zz 2 2 zz 2 zz 2 2 em ew ew em 2 em ew ew em ew ew ew em wm e 1
54. RED VVANPPP1 Connect Gateway Information DNS Information Primary Secondary Figure 4 6 6 1 WAN Status IPv6 Tab The screen contains the details as described in table of Fields in WAN Status 4 6 7 DNS To configure the Domain Name Server DNS address click the DNS link WAN DNS on the left navigation bar A screen is displayed as shown in Figure 4 6 7 For statically configured WAN it is mandatory to configure DNS addresses through this page Domain Name System DNS A Domain Name System DIS server translates hostnames or domain names to IP addresses Most ISPs provide a DNS server for speed and convenience Since your Service Provider may connect to the Internet with dynamic IP settings it is likely that the DNS server IP addresses are also provided dynamically However if there is a DNS server that you would rather use you need to specify the IP address below IPva APv T TR Domain Name Server DNS Address D L8 B8 i Figure 4 6 7 DNS Configuration Secondary DNS Address optional 50 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 p Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in DNS Field Description Select the appropriate tab to configure IPv4 or IPv6 IPv6 IPv4 IPv6 support Is currently not available for DNS configuration Secondary DNS Address Enter the
55. RUBY Y VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications H www rubytech de info amp rubytech de IeLUWOrKITIg t LommMunNIcations www rubytech de info rubytech de R LINE PHONE POWE Resel a RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de Copyright Copyright 2012 by RubyTech Deutschland GmbH All rights reserved Trademarks RUBYTECH is a trademark of RubyTech Deutschland GmbH Other brand and product names are registered trademarks or trademarks of their respective holders Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics With respect to any examples or hints given herein any typical values stated herein and or any information regarding the application of the device Ruby Tech Deutschland GmbH hereby disclaims any and all warranties and liabilities of any kind including without limitation warranties of non infringement of intellectual property rights of any third party Statement of Conditions In the interest of improving internal design operational function and or reliability RUBY TECH reserves the right to make changes to the products described in this document without notice RUBYTECH does not assume any liability that may occur due to the use or application of the
56. Registered user name with DDNS service provider Click Apply for applying the DDNS changes into system Click Cancel to exit from this page without saving the changes 4 6 9 OAM Configuration This page provides ATM F5 based OAM test Hence the settings are valid only for ATM based WAN To configure the ADSL OAM settings click the OAM Configuration link WAN OAM Configuration on the left navigation bar This release supports only F5 type of OAM tests as shown in Figure 4 6 9 ADSL OAM Configuration OAM Setting Table No VPI VCI Loopback TX Cells Update Entry 0 35 Disable DUU 3 2 0 Disable DUU 3 CH OAM Settings Select Made VPI Channel lo VCI Channel Select Method PING Loopback C Enable Transmit interval time 60 10000 Milliseconds Humber of Tx Cells 1 100 Figure 4 6 9 ADSL OAM F5 Test 52 e RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in ADSL OAM F5 Test page Description This table displays all active connections with following OAM parameters information No Number VPI Virtual Path Identifier OAM F5 Settin d VCI Virtual Connection Identifier Table Loopback Enabled or Disabled Transmit Time actual value in milliseconds Tx Gells No of cells to be transmitted Update Entry F5 Transmit Configures the time i
57. VLAN pool Pool This displays the current configured VLAN pool for auto detect in MII 0 VLAN Pool MII 0 WAN mode Add Delete MII O VLAN to ssl Add or delete VLAN to MII 0 VLAN pool OO VCC Pool This displays the current configured VCC pool for auto detect in OO ADSL ATM WAN mode Add Delete VC to Pool Add or delete VCC to ADSL ATM VCC pool Select this to enable VCC auto detection from the specified pool for ADSL ATM WAN mode L2 ADSL PTM VLAN Auto Select this to enable VLAN auto detection from the specified pool L2 VDSL PTM VLAN Auto Select this to enable VLAN auto detection from the specified pool for VDSL PTM WAN mode L2 VCC Auto Detect 35 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Fields in Auto detect Config cont d Field Description L2 MII 1 VLAN Auto Select this to enable VLAN auto detection from the specified pool for Detect MII 1 WAN mode Select this to enable WAN auto detection in sequence of L3 VCC Auto Detect PPPoE DHCP in ADSL ATM WAN mode L3 VDSL PTM VLAN Select this to enable WAN auto detection in sequence of Auto Detect PPPoE DHCP in VDSL PTM WAN mode L3 MII 0 VLAN Auto Select this to enable WAN auto detection in sequence of Detect PPPoE DHCP in MII O WAN mode 4 6 3 WAN Channel Config To configure the WAN Channel Config click the WAN Channel Config WAN gt WAN Channel
58. a single telephone wire that can installation within suitable distance depends on speed Figure 2 2 Projekt VDSL2 DSLAM g RUBY 200 Mbit s voll duplex LAN Verbindung egen eared Garon ber bestehende Telefonverkabelung fuesen 27 9200 Haibach P COD Node Fo aech Figure 2 2 VC 400RT application 2 6 1 Connect the VC 400LT and the VC 400RT to the Line The objective for VDSL2 is to pass high speed data over a twisted pair cable In the setup connect VC 400LT to VC 400RT through phone wire 24 26 AWG or line simulator or any other hardware representation of a cable network with or without noise injection and crosstalk simulations 10 RUBY h VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 2 6 2 Connect the VC 400LT and the VC 400RT to LAN Devices In the setup usually an Ethernet tester serves as a representation of the LAN side as well as a representation of the WAN side 2 6 3 Run Demos and Tests The Ethernet tester may send data downstream as well as upstream It also receives the data in order to check the integrity of the data transmission Different data rates can be tested under different line conditions BHSBISESI Hardware Description This section describes the important parts of the vdsl2 router It features the front panel and rear panel P 0 WE Ek VC 400RT Outward l1 RUBY VC
59. able the particular packet filtering rule To specify the output interface of the packet from dropdown options e g WAN2 Click Apply at any time during configuration to for adding the packet filtering rule Click CANCEL to exit from this page without saving the changes Add a packet filtering rule Allows to ceate a packet filtering rule thereby conforming traffic is denied access Ingress Interface Any v Exclude Egress Interface Any s Exclude IP Version P IPv6 Destination Address H C Exclude IPv6 Source Address HL C exclude Protocol Any v Exclude Destination Port k Exclude Source Port Exclude Target Drop sw Enable this rule Figure 4 9 3 2 Add a Packet Filtering Rule for Firewall IPv6 69 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in Add a Packet Filtering Rule IPv6 page Field Description Ingress To specify the input interface of the packet from dropdown options e g Interface WAN1 Exclude To exclude the selected option IP Source Address To specify the source IP address To specify the range of the source port Valid for protocols TCP or UDP Source Port only The destination IP can be a SINGLE address or a SUBNET or All Destination IP involving a
60. address of the secondary DNS server if available It optional is an optional parameter Click Cancel to exit from this page without saving the changes Click Apply for deleting the WAN connection 4 6 8 DDNS The Dynamic DNS is useful for getting a FQDN URL registered for a dynamic IP address to a DNS service provider The VC 400RT software integrates support for three Dynamic DNS service providers e dhs e dyndns e dyns The user needs to register first with a chosen DNS Service provider The registered information needs to be configured in DDNS settings web page To configure thee registered information in DDNS settings page click the DDNS link WAN gt DDNS on the left navigation bar A screen is displayed as shown in Figure 4 6 8 DDNS Settings Dynamic DNS allows you to update your dynamic IP address with one or many dynamic DNS services So anyone can access your FTP or Web service on your computer using DNS like address Enable DDNS Support PASTE EEE L yn dhs org Q dyndns dyndns org Q dyns dyns cx Figure 4 6 8 DDNS Settings 51 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in DDNS Field Description Enable DDNS support Check box to enable DDNS support in CPE DDNS Server Dynamic DNS Server Provider User Name
61. ation bar This can be used for allowing specified IP addresses to access the VC 400RT CPE from WAN The system allows upto 16 ACL entries to be configured in the CPE device A screen is displayed as shown in Figure 4 9 7 Access Control IP Address Figure 4 9 7 Application Server Settings The screen contains the following details Fields in ACL Setting Field Description Enable ACL To enable disable ACL settings Click Apply after filling the IP address for adding the entry in ACL list Click Cancel to exit from this page without saving the changes 4 10 NAT You can view the NAT on the left navigation bar of the VC 400RT CPE homepage The menu below includes the sub menus of NAT Settings Virtual Server PortTriggering and DMZ Following are the options available under NAT as shown in Figure 4 10 13 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 e Networking amp Communications www rubytech de info rubytech de NAT Settings Virtual Server Port Triggering DMZ Figure 4 10 NAT Options 4 10 1 NAT Settings To configure Network Address Translation NAT click the NAT Settings link NAT gt NAT Settings on the left navigation bar A screen is displayed as shown in Figure 4 10 1 NAT Settings Network Address Translation HAT allows multiple users at your local site to access the Internet through a single public IP address or multiple public IP addresses NAT ca
62. ble list of VC 400RT click on the Routing Table List link in the left navigation bar A screen is displayed as shown in Figure 4 8 3 Routing Table The Rauting table displays configured rautes and interfaces an CPE device E 192 168 16 0 2323 232 255 l0 0 0 0 0 Figure 4 8 3 Routing Table List 64 RUBY TECH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in Static Routing Field Description Destination IPv4 address for route IPv4 gateway address for this route This depends on the interfaces currently configured in the system Possible values are brO Bridge interface ethO First ethernet mur interface eth1 Second ethernet interface maybe connected to an external switch nas lt i gt e g nasO Ethernet over ATM interface Applicable only to ATM WAN ppp lt i gt e g pppO PPPoE or PPPoA interface Routing Table List IPv6 Tab If IPv6 functionality is enabled through Quick Setup gt IPv6 then the Routing Table List web page also lists all IPv6 routes in system under IPv6 tab as shown in Figure 4 8 3 1 Routing Table The Routing table displays configured routes and interfaces on CPE device uen ty fc00 64 gt 256 br 64 256 br 80 64 256 f102 1 128 f102 1 0 t 8 256 b IPv6 functionalities are not supported in this
63. bytech de ER EN AO SELECT WAN EE 32 4 6 1 WAN Mode Selection srein EAE RET EEEa 32 46 2 Auto Delect Seting ERR 33 4 6 9 WAN Ghannel ee e DEE 36 46A V LAN Channel Con nee een 38 E WAN SS JR ee RET 40 Ee 48 Ap IN 50 40o DON m 51 46 9 OAM COMIGUIATO eege deet Eeer 52 A SELECT EAN E 54 Al LAN JU cT a ne er 55 A472 EAN SEIN ee ee ee ee ee 55 A UPR WIC VI COS IST ee ee ee nie 60 4 7 4 LAN Switch Port OC LUNG near ea 60 EE eege 61 4 8 SELECT ROUTE ee 61 e AR Ten Gel le seen S m 62 AB o RIP SUBDOE Eege 63 483 Routing Tale LIS c 64 AI ELECT EIRE WAL geen 65 A O21 TIVE WW E S e N BE 66 4 9 2 IPv6 Firewall Gettmng lessen nennen nnnm nnn nnn nnns 66 4 9 3 Ice FIG ocn n EACRLIToREXS vos SIR ERU ERUPSAM EEUU EUM UDPdEX ER CRF TEN ME EAM EA OP GRNRESE 67 2 IA E MN MN avenue I D mmm 70 4 95 Paremal os OHIO MET E 71 4 9 6 Application Server Gettnges 72 4 9 7 Access Control List TAG anna 73 NIU HR 73 NIU MEE SC WINGS MER m 74 Behe WIEN SOLVE castos tenuta ee EE 74 AMOS FOr Beie CT eR m 77 SRI ED c 79 AA OOS e n 79 AAE TOO S CUN RET TR 80 A112 eue CONG DEE 81 Gis ESAE E oa ONIN e E 83 412 ON Lg E nee een 86 RUBY Deutschland GmbH Networking amp Commun
64. cal xDSL line 4 6 Select WAN You can view WAN link on the left navigation bar for WAN related settings Select the NAT The menu below includes the sub menus of WAN Mode Selection WAN Channel Config VLAN Channel Config WAN Setting WAN Status DNS DDNS and OAM Configuration A screen is displayed as shown in Figure 4 6 WAR Mode Selection Auto Detect Contig WAN Channel Contig VLAN Channel Contig WARN Setting DNS DONS GAM Configuration Figure 4 6 WAN options 4 6 1 WAN Mode Selection To configure the WAN Mode Setting click the WAN Mode Selection WAN gt WAN Mode Selection on the left navigation bar A screen is displayed as shown in Figure 4 6 1 32 e RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 WAN Mode Selection This page allows to select the physical WAN made in CPE device This has to be first configured before any WAN configuration is done Failover Support Physical WAN Selection Physical WAN Type Auto DSL v Negotiated WAN Mode Connecting Figure 4 6 1 WAN Mode Setting Seleted Auto Failover Support d Physical WAN Selection Physical VAM Type TC Type ES a Figure 4 6 1 1 WAN Mode Setting Seleted ADSL2 VDSL2 The screen contains the following details Fields in WAN Mode Setting Field Description LLLI Failover Support Select this chec
65. ce can be downloaded to PC using BACKUP button and can be uploaded back using RESTORE button System Time Administrator Settings Web Settings Software Firmware Upgrade Backup Backup to local host Configuration Settings System Log SSL Certificate Reset Statistics gt Restore Restore from local host G Figure 4 3 6 Configuration Settings 24 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 p Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Fields in Configuration Settings Field Description Backup to local host This will backup the current active configuration of CPE in Host machine Click Next to start the firmware upgrade process Click Cancel to exit from this page without saving the changes B Backup Current Active Configuration As mentioned before this option allows user to backup the current active configuration running in router system This is very helpful when a user wants to backup the current working configuration of router for rollbacks if required in future It is recommended that before any complex nature of configuration is done by user the current active configuration should be backed up in host machine The Local Host Configuration backup are shown in Figure 4 3 6 1 Confisuration Backup This feature saves the configuration of the device to a file in azipped format Click Here Figure 4 3 6 1 Configuration Backup Wh
66. click the RIP Support link Route RIP Support on the left navigation bar A screen is displayed as shown in Figure 4 8 2 Dynamic Routing The dynamic routing feature of the router can be used to allow the router to automatically adjust to physical changes in the network s layout The router uses the dynamic RIP protocol It determines the route that the network packets take based on the fewest number of hops between the source and the destination The RIP protocol regularly broadcasts routing information to other routers on the network Dynamic Routing Enable Disable Listen Mode RIP2 Supply Mode IR RIP2 ze RIPng RIPng O Enable Disable GL A LAS QC Figure 4 8 2 Dynamic Routing 63 CS RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in Dynamic Routing Field Description Dynamic Routing To enable or disable the Dynamic Routing RIP in CPE To configure the supply mode of RIP to Disabled RIP1 RIP2 Supply Mode Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 8 3 Routing Table List The Routing table allows you to see how many routings on your VDSL2 router routing table and interface information To view the Routing entry ta
67. corresponding device 2 4 Verify that the proper cable type is used and its length does not exceed specified limits Solution pis 2 5 Check the router on the attached device and cable connections for possible defects 2 6 Make sure that the phone wire must be connecting VC 400RT first when powered on 2 Replace the defective router or cable if necessary E 106 VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Solution 3 1 Please make sure that the phone wire must be connected between VC 400LT CO and VC 400RT CPE when both are power on VC 400LT CO will do link speed function depending on phone wire length therefore if VC 400LT CO can t detect VC 400RT CPE over phone wire while both power on this will cause the link to fail 3 2 Please check phone wire we recommend use 24 26 gauge with twisted pair and without rust 3 3 3 Please reinsert power when change cable length or link time over 3 minutes Seege Note Phone wire must meet CAT 3 standard or above and without clustering otherwise will cause more cross talk issue to reduce DSL power driver Answer Very high speed digital subscriber line 2 VDSL2 is an access technology that exploits the existing infrastructure of copper wires that were originally deployed for traditional telephone
68. creen is displayed as shown in Figure 4 13 1 IPsec Tunnel Confisuration On this page you can configure different IPsec tunnels Figure 4 13 1 IPsec Tunnel Configuration When you click Add button in the IPsec Tunnel Configuration page a screen is displayed as shown in Figure 4 13 1 1 Add IPSec Tunnel Confisuration Tunnel Name AUTH METHOD Prefixed Key PSK Secret E KE Mode ikev2 WAN Interface DOSEN Peer Address o o D o Peer Subnet ja o ra o ly o Enable u IKE Cipher aes192_cbe IKE Hash shat IKE DH Group modp1536 ze IKE PRF aes xbc WM ESP Cipher aes128 cb cbe bc ei ESP Hash shat si Key Lifetime 80 Minutes Retry lo means always retry He Figure 4 13 1 1 Add IPSec Tunnel Mode Configuration 89 gt RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in Add IPSec Add Configuration Field Description Tunnel IPsec Tunnel name Name PSK Shared secret string used for tunnel authentication Secret San WAN on which tunnel to be created Interface Peer Remote tunnel end point address Address Enable or Disable of tunnel IKE Hash Hash algorithm to be selected from dropdown IKE PRF PRF algorithm to be
69. cription Application Specify Application name from dropdown or custom name for Virtual Name Server rule Private IP Specify Private IP address of Virtual Server rule Public Port Specify Public Port range Enabled To enable the specified entry of the virtual server tick on check box Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 76 CS RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 10 3 Port Triggering To configure Port Triggering click the Port Triggering link NAT Port Triggering on the left navigation bar A screen is displayed as shown in Figure 4 10 3 Port Triggering You can configure the CPE device for Port Triggering functionality In other words depending on the requested service TCP UDP port numbers the CPE device redirects the external service request to the appropriate server located at another internal IP address You can add maximum of 16 entries ie e Application Trigger Trigger Trigger External External Open Enable Name Start Port End Port Protocol Start Port End Port Protocol i Figure 4 10 3 Port Triggering The screen contains the following details Fields in Port Triggering Field Description Application Te Port Triggering Application Name Trigger End T
70. ct Pool Config ADSL PTM VLAN Pool 101 0 S See Add Delete ADSL PTM VLAN to Pool E VDSL PTM VLAN Pool 201 0 Add Delete VDSL PTM VLAN to Pool 5 MII 1 VLAN Pool 301 0 Add Delete MII 1 VLAN to Pool m MII O VLAN Pool 401 0 Add Delete MII O VLAN to Pool YCC Pool 1 0 32 8 35 0 35 Add Delete VCC to Pool l e i i Auto Detect Layer Specific Setting L2 VCC Auto Detect L3 Ycc Auto Detect a HTML OO EUER L3 ADSL PTM Auto Detect Detect Bei Nonum L3 VDSL PTM Auto Detect L2 MII 1 MAN Auto Detect L2 MII 0 VLAN Auto Detect L3 MII 1 Auto Detect L3 MII O Auto Detect s s S s K Figure 4 6 2 Port Mapping Configuration 34 CR RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 CT Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in Auto detect Config Field Den This displays the current configured VLAN pool for autodetect in ADSL PTM VLAN Pool ADSL PTM WAN mode Add Delete ADSL PTM Add or delete VLAN to ADSL PTM VLAN pool VLAN to Pool This displays the current configured VLAN pool for autodetect in VDSL PTM VLAN Pool VDSL PTM WAN mode Add Delete VDSL PTM Add or delete VLAN to VDSL PTM VLAN pool VLAN to Pool This displays the current configured VLAN pool for autodetect in MII 1 VLAN Pool MII 1 WAN mode Add Delete MII 1 VLAN to Add or delete VLAN to MII 1
71. ctions Select the Route The menu below includes the sub menus of Static Routing RIP Support and Routing Table List Following are the options available under Route menu as shown in Figure 4 8 61 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Route gt Static Routing RIP Support Routing Table List Figure 4 8 Route Options on the Left Navigator Bar 4 8 1 Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router You can use static routing to allow different IP domain users to access the Internet through this VDSL2 Router device To setup Static Routing click the Static Routing link Route gt Static Routing on the left navigation bar A screen is displayed as shown in Figure 4 8 1 Static Routing The static routing function determines the path that data follows over your network before and after it passes through your router You can use static routing to allow different IP domain users to access the Internet through this device The default route cannot be added from this web page The default route is added in system automatically based upon the Gateway selection in WAN Settings page GEET L d I t Figure 4 8 1 Static Routing Configuration The screen contains the following details Fields in Static Routing
72. d Settings link Multicast Advanced Settings on the left navigation bar A screen is displayed as shown in Figure 4 12 3 IGMP Advanced Settings Configurable parameters to tune IGMP performance cy pe Fast Leave O Group Query Response Interval O j 1 125 seconds Group Last Member Query Interval al 1 3600 seconds Group Last Member Query Count L 1 10 ee Qi a Qs p Figure 4 12 3 Multicast Advanced Settings 87 RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in Multicast Advanced Settings Field Description IPv4 IPv6 Choose the appropriate tab to configure either for IPv4 or IPv6 Group Query Interval Specify Group Query Interval in range of 1 3600 seconds vide ast empon NEN Group Last Member Query Interval in range of 1 3600 seconds 4 13 IPsec When you click IPsec on the left navigation bar of the VC 400RT CPE homepage The menu below includes the sub menus of Tunnel Mode The following option Tunnel Mode is available under IPsec as shown in Figure 4 13 Deech Figure 4 13 IPsec Option 88 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 13 1 Tunnel Mode When you click the Tunnel Mode link IPsec Tunnel Mode on the left navigation bar a s
73. d electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately 112 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Warranty The original product that the owner delivered in this package will be free from defects in material and workmanship for one year parts after purchase There will be a minimal charge to replace consumable components such as fuses power transformers and mechanical cooling devices The warranty will not apply to any products which have been subjected to any misuse neglect or accidental damage or which contain defects which are in any way attributable to improper installation or to alteration or repairs made or performed by any person not under control of the original OWner The above warranty is in lieu of any other warranty whether express implied or statutory including but not limited to any warranty of merchantability fitness for a particular purpose or any warranty arising out of any proposal specification or sample We shall not be liable for incidental or consequential damages We neither assume nor authorize any person to assume for it any other liability WARNING WARNING Warranty Void 1 DO NOT TEAR OFF OR REMOVE TH
74. de Fields in AdministratorSettings Description Select User Select user type The available options are Admin and support user The user should specify the new password desired The password Password should be at least 3 characters and not more than 16 characters in length without a white space Fields in AdministratorSettings Cont d Field Description Enable Account To enable the user account login Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 3 4 Web Settings This page shows the details of Web login timeout settings for the CPE device in seconds Click the Web Settings link System Web Settings on the left navigation bar and a screen is displayed as shown in Figure 4 3 4 ETE Web Timeout Settings Host Name Config Set Autologouttime in seconds limit for CPE device System Time Administrator Settings Web Settings ELM GEIL Software Firmware Upgrade Configuration Settings System Log Autologout Duration 1800 Figure 4 3 4 Web Settings Fields in Web Settings Description Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 23 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info ruby
75. e and above level of logs are viewed Warning Warning type and above levels of logs are viewed Error Error type and above levels of logs are viewed Critical Critical type and above levels of logs are viewed Alert Alert type and above level of logs are viewed Emerg Emergency type of log information is viewed Click Save Changes to configure the system log settings View System Log w 99 9 999 Click View Log to fetch the logs in browser When you click View log button a screen is displayed as shown in Figure 4 3 7 1 This screen is an example of system log of default level as shown in the browser System Log liv 29 23 34 50 nane dasemon info re end 1663 Ve amp uthHandlar per failed Nov 29 23 34 50 none daemon info mira hitpd 1683 Ve uthHandler pir failed Now 29 23 23 24 mana deemon err rini hetpd 1653 f Det vian ip eonig returned failure Woy 29 23 44 23 none daemon infa mini hikgd 1563 192 168 16 9 File lavicnn ve rs protected How 29 23 44 77 mone daemon infa mins Fitpd 1663 192 168 16 9 File fawican ics is protected Him 29 23 44 30 mone deeman inio mini hitad 1683 192 155 16 9 File favican ice is protected hoy 29 23 44 30 nane daemon inZn mini Fittnd 1663 183 168 16 9 File favicnn ico is protected Nov 29 23 44 31 none deemon infg mini htrpd 1653 192 168 16 9 File favicon vo rs protected liv 29 23 53 31 mane dasmen inio mini Fittpd 1663
76. e wire Standard telephone wire of any gauge or type flat twisted or quad is used to connect the Modem to the telephone network A telephone cable typically consists of three pairs of wires one of which is used for transmission The connector at the end of the telephone cable is called an RJ 11 connector and it consists of six pins POTS plain old telephone services use pins 3 and 4 for voice transmission A telephone cable is shown below Figure A 4 A B Figure A 4 Telephone cable The A and B connectors on the rear of the Modem are RJ 11 connectors These connectors are wired identically The RJ 11 connectors have six positions two of which are wired The Modem uses the center two pins The pin out assignment for these connectors is presented below Table A 2 Table A 2 RJ 11 Pin out Assignments 96 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Spe Product Specification Key Features amp Benefits Support ATM and PTM transmission mode auto detection ADSL Annex B backward compatible Supports high bandwidth up to 100Mbps symmetric over line ports Support 8a 8b 8c 8d 12a 12b 17a 17b and 30a band profile and Support 997 998 band plan Support ATM TC ATM and AAL5 ATM Flow Throughput OAM Cell Filter and Forwarding AAL5 SAR PVC ATM Traffic Class ATM PVC Shaping
77. econdary DNS Prefix Delegated view D E GG 58 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Figure 4 7 2 3 LAN Settings IPv6 Tab Option 2 SLAAC LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCPv6 configuration LAN IPv6 Configuration IPv6 Address fc00 1 64 IPv6 Address Auto Configuration Auto Configuration Mode Statefull DHCPv6 v Statefull DHCPv6 IPv6 Pool Start Address fc00 100 IPv6 Pool End Address fc00 200 Primary DNS fc00 1 Secondary DNS DNS Domain name lantiq com Prefix Delegated view GU IP GL IAS OLD Figure 4 7 2 4 LAN Settings IPv6 Tab Option 3 Statefull DHCPv6 Server For LAN interface the VC 400RT uses SLAAC based prefix assignment to LAN hosts The IPv6 prefix obtained from DHCPv6 on WAN is automatically passed to LAN hosts for their IPv6 address configuration The screen contains the following details Fields in LAN Settings IPv6 Field Description LAN IPv6 Configuration IPv6 Address IPv6 Address of CPE IPv6 Address Autoconfiguration Auto Configuration Mode on LAN interface for LAN hosts Stateless Auto Config SLAAC Statefull DHCPv6 Stateless Auto Config SLAAC Statefull DHCPv6 Stateless Address Autoconfiguration Stateless Address Autoconfiguration Auto Configuration Mode Prefix Prefix Length IPv6 Pr
78. efix and Length Configuration Primary DNS Primary DNS for IPv6 name resolution Statefull DHCPv6 Primary DNS Primary DNSv6 Address Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes When you click Prefix Delegated view button in the LAN Settings IPv6 page a screen is displayed as shown in Figure 4 7 2 5 59 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de Prefix Delegated br 2001 db8 36 500 64 Figure 4 7 2 5 Prefix Delegated view Click Back to exit from this page 4 7 3 UPnP Devices List To discover the UPnP Devices in LAN network click the UPnP Devices link LAN UPnP Devices on the left navigation bar A screen is displayed as shown in Figure 4 7 3 UPnP Devices List The UPnP Devices list allows you to see al UPnP devices that are discovered by the CPE 192 168 16 207 ADSL Router InternetGatewayDevice aaa00001 bfde 1103 832c 00056e020010 192 168 16 254 D Link Internet Gateway Device 0015E909 A59E D317 C7 98 0000COA810FE Figure 4 7 3 UPnP device list The screen contains the following details Fields in UPnP Device List _ Description Click Refresh to view a new UPnP devices list 4 7 4 LAN Switch Port Setting To discover the All LAN Port Setting in LAN network clic
79. en you click Backup button as shown in Figure 4 3 6 1 it will backup the config settings of CPE in connected PC from where Web UI is being accessed 25 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de B Restore Previous Backed up Configuration As mentioned before this option allows user to restore the earlier backed up configuration in router system This operation is handy for restoring the system to last backed up configuration mode The Local Host Configuration restore are shown in Figure 4 3 6 2 The system will go for reboot after configuration is restored When CPE boots up it will be running with newly applied configuration Configuration Restore The CPE device configuration file backed up earlier can be loaded back on CPE device Enter the path and name of the Configuration file and then click the APPLY button below You will be prompted to confirm the restore process NOTE The Configuration file should be in gzipped i e with suffix gz Figure 4 3 6 2 Configuration Restore Click Apply button to restore the config settings 4 3 7 System Log To view the logs produced in system click the System Log link System System Log on the left navigation bar A screen is displayed as shown in Figure 4 3 7 System Log Configure System Log Local Remote O Local and Remote Filter Level Default v View System Log
80. escription This option allows to select following modes of IPv6 configuration Stateful DHCPv6 IA NA and IA PD SLAAC Address Configuration with DHCPv6 IA PD This option allows to configure different DUID DHCP Unique Identifier types Type 1 LLT Link Layer Time Type 2 EN Enterprise Number Type 3 LL Link Layer IANA option represents IPv6 address and parameters related to the same being accepted by DHCPv6 clients IANA is the Identity Association for Non Temporary Addresses option This Identifier to be configured when Stateful DHCPv6 configuration mode is selected IAPD options represent one or more IPv6 prefix and parameters related to it IAPD is the Identity Association for Prefix Delegation This identifier to be configured in both Stateful DHCPv6 or SLAAC DHCPV 6 configuration modes This parameter is called Site Level Aggregation Identifier This identifier is used to configure the subnet for DHCPv6 client configuration This declaration enables DHCPv6 client to request the DHCPv server to perform a Rapid Commit Handshaking will happen with two DHCPv6 messages This option allows to configure default route for relevant WAN mode of this WAN connection Click Cancel to exit from this page without saving the changes 4 6 5 5 Bridge The option Bridge enables the bridge mode which is a common connection method used for xDSL modem Select this option on WAN Settings page and clic
81. f frequent errors that require the source transmitting computer or terminal to resend some packets of data SNR measures the quality of a transmission channel over a network channel The greater the ratio the easier it is to identify and subsequently isolate and eliminate the Source of noise l Some testing program which is base on TCP IP protocol such as FTP Iperf NetlQ the We recommend to test VDSL2 bandwidth best by Smartbit equipment if you don t have T Smartbit we recommend test that by IPERF program and TCP window size must be me settled max 64k the parameter as iperf c server IP address i 1 t 50 w 65535 for client side Re Please note VC 400RT is a remote side CPE side it must be connected to the CO side to work Tone mode Band profile and band plan setting must be compatible to Answer each other if not access error will show when applied Please deactivate and activate once the setting has been changed D e ee E E E nn nn nn nn nn nn nn nn nn E E E nn nn nn nn nn nn nn nn nn nn mn nn nn nn nn 108 gt RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 When the application is used within the LAN the switch bridged mode is not necessary to set up a gateway However if the application crosses various network segments LAN to WAN or WAN to LAN
82. fault Based on this type of commercial standard connection policy if you are using a full duplex device that does not support auto negotiation communications can be easily lost i e reset to the wrong mode whenever the attached device is reset or experiences a power fluctuation The best way to resolve this problem is to upgrade these devices to a version that support Ethernet and VDSL Physical Configuration If problems occur after altering the network configuration restore the original connections and try to track the problem down by implementing the new changes one step at a time Ensure that cable distances and other physical aspects of the installation do not exceed recommendations System Integrity As a last resort verify the switch integrity with a power on reset Turn the power to the switch off and then on several times If the problem still persists and you have completed all the preceding diagnoses then contact your dealer 110 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de DER Compliance Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device pursuant to Part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This
83. ge or above The RJ 11 connectors have six positions two of which are wired The router uses the center two pins The pin out assignment for these connectors is presented below RJ 11 Pin out Assignments Pint MNEMONIC FUNCTION Unused Unused Unused Unused RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de 2 4 Connecting the Router The router has four Ethernet port which support connection to Ethernet operation The devices attached to these ports must support auto negotiation 10Base T 100Base TX 1000Base TX unless they will always operate at half duplex Use any of the Ethernet ports to connect to devices such as Monitor system Server Switch bridge or router Notes 1 Ihe RJ11 Terminal Block Line port is used to connect the telephone that is connected to VDSL2 CO and CPE router Point to point solution 2 Slave device CPE must be connect to the Master device CO through the telephone wire The Slave cannot be connected to another Slave and the Master cannot be connected to another Master 2 5 Connecting the RJ 11 RJ 45 Ports The line port has 2 connectors RJ 11 and terminal block It is used to connect with VC 400LT CO using a single pair phone cable to VC 400RT CPE bridge side point to point solution Take note that VC 400RT line port cannot be used at the same time Either RJ 1 1 port
84. ications www rubytech de info rubytech de e VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 A122 PIOXY Oe Rem EE A 86 A122 SOO OIC Bn Te EO Do E 87 4 12 3 Advanced Rue secte astetostenesi een ee 87 BT 88 AST Tne LA ae 89 PREMIT sr 90 Qi E PVG Se ING NOR m t 91 ENEE 91 4 14 9 DS Lite Contig rdtlOliassaec ucc em 92 dd 5 DIGIC e 93 4 15 1 Diagnostic Test SUING E 94 EENEG CABLE REQUIREMENTS nmn 95 BEBENDIREI PRODUCT SPECIFICATION nnn 97 WRENS ROUTER MODE SELECT nnnc 109 APPEND VC 400LT VC 400RT PERFORMANCE TABLE mRRHMRRn 109 MPENDE TGOUIDL EGHOOTING 110 BEBENDEREI COMPLIANCE INFORMATION 111 WARRANTY su 0000000 anna rennen gene 113 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubvtech de info rubytech de CHAR Installing the Router 2 1 Hardware Installation This chapter describes how to install the router and establish the network connections The VC 400RT may be installed on any level surface e g a table or shelf However please take note of the following minimum site requirements before you begin The VC 400RT has 2 pre installed rubber feet 2 2 Pre installation Requirements Before you start the actual hardware installation make sure you can provide the right operating environment including power requirements sufficient physical space
85. ill enable the upstream QoS Downstream QoS Enable This selection will enable the downstream QoS 8021P Remarking Enable Disable This will enable disable global 8021P Remarking WAN Port Rate Limiter Check box for limiting physical port rate limit on WAN upstream link PPA Session Acceleration Setting PPA Session To enable disable the session acceleration feature Acceleration Click Apply for applying the QoS setting changes into system Click CANCEL to exit from this page without saving the changes 80 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 11 2 Queue Config To configure the Queue Config click the Queue Config link QoS Queue Config on the left navigation bar A screen is displayed as shown in Figure 4 11 2 WAN Egress Queue Configuration Configure queues in CPE device to be used for QoS controlled traffic flows The queue entries configured here will be used by classifier to place packets appropriately Queue Queue Drop Schedule Queue Committed Peak Enable Action Name Precedence Algorithm Algorithm Weight Shaping Rate Shaping Rate i 8 DT SP 0 Yes CH def queue 60000 gi 1 DT SP 60000 Yes Q qz 2 DT SP 0 60000 Yes Q Figure 4 11 2 Queue Config The screen contains the following details Fields in Queue Config Upstream Field Description Raa a Selection tab for
86. ils Fields in LAN Settings Field Description Host Name Host Computer name MAC Address MAC address of Host computer for which static IP reservation is needed To add this IP reservation entry Click APPLY to save the changes that you have entered Click CANCEL to exit from this page without saving the changes The following pages describe the LAN Settings for IPv6 LAN Settings IPv6 Tab If IPv6 functionality is enabled through Advanced Setup IPv6 then LAN Settings web page also presents IPv6 tab Based on the Auto Configuration Mode the following screens are displayed is as shown in Figure 4 7 2 2 Figure 4 7 2 3 and Figure 4 7 2 4 LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCPv6 configuration ee ty IPv6 Address fe00 1 _ Je Auto Configuration Mode Stateless Address Autoconfiguration Stateless DHCPv6 v Prefix Prefix length fe00 Hu 54 Stateless DHCPv6 Primary DNS fc00 1 Secondary DNS DNS Domain name llaniqgcom t Prefix Delegated Help Figure 4 7 2 2 LAN Settings IPv6 Tab Option 1 SLAAC Stateless DHCPv6 LAN Settings You can configure LAN settings of CPE device such as LAN IP Address and DHCPv6 configuration H ty IPv6 Address ap ie Auto Configuration Mode Stateless Address Autoconfiguration v Prefix Prefix length Ion m M D Route Primary DNS fc00 1 S
87. ing amp Communications www rubytech de info amp rubytech de WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel 5 VCC prpoatm 1 WAN TYPE PPPoA E User Name Password Please retype your password MTU pppoa 1400 1492 pppoe 1400 1500 1492 PPP Option Auto Connect v Address Version IPv4 IPv6 WAN IPv6 Configuration Configuration Modes Stateful DHCPv A NAandlA FD v DUID Type Type 1 LLT Link Layer Time e JANA ID D TAPD ID 0 SLA ID 0 i Rapid Commit m Default WAN EI Figure 4 6 5 6 WAN PPPOA creation The screen contains the following details Fields in PPPoA WAN Field Description User Name To enter the username to be used in the PPPoA session Please retype your password To enter the password again to reconfirm This feature allows to automatically re connect to the service Dial on Demand provider once the connection was lost The checkbox can be enabled or disabled for this feature For PPPoA the only supported IP addressing is IPv4 currently The IPv6 for PPPoA is not available in this version of VC 400RT Address Version 46 VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 d CR RUBY Fields in PPPoA WAN IPv6 Configuration Configuration Modes DUID Type IANA ID IAPD ID SLA ID Rapid commit Default WAN Click Apply at any time during configuration to save the information that you have entered D
88. is connected or terminal block is connected using a straight connection Figure 2 4 or cross over connection Figure 2 5 When inserting a RJ 11 plug make sure the tab on the plug clicks into position to ensure that it is properly seated 9 Do not plug a RJ 11 phone jack connector into the Ethernet port RJ 45 port This may damage the NV 600A router Instead use only twisted pair cables with RJ 45 connectors that conform to Ethernet standard Figure 2 1 VC 400RT line ports straight connection RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Notes 1 Be sure each twisted pair cable RJ 45 ethernet cable does not exceed 100 meters 333 feet 2 We advise using Category 5 7 UTP STP cables for Cable bridge or Router connections to avoid any confusion or inconvenience in the future when you attached to high bandwidth devices 3 RJ 11 VDSL2 Line port use 24 26 gauge with twisted pair phone wiring we do not recommend 28 gauge or above 4 Be sure phone wire has been installed before VC 400RT powered on 2 6 VDSL2 Application The router s line port supports 100Mbps 0 3km for data service across existing phone wiring It is easy to use which do not require installation of additional wiring Every modular phone jack in the home can become a port on the LAN Networking devices can be installed on
89. ize the system clock to the global Internet The synchronized clock in the Modem is used to record the security log and control client filtering This page provides the time zone selection and NTP Network Time Protocol configuration Click the System Time link System System Time on the left navigation bar and a screen is displayed as shown in Figure 4 3 2 System Time Host Name Config System Time Administrator Settings Web Settings Software Firmware Upgrade Connecting to a Simple Network Time Protocol SNTP server allows the CPE device to synchronize the system clock to the global Internet Current System Time Configuration Settings Set Time Zone GMT 05 30 Calcutta Chennai Mumbai New Delhi Sri Jayawardenepura v System Log M SSL Certificate SNTP Client Enable l Reset Primary SNTP Server 0 asia pool ntp org b4 Statistics Secondary SNTP Server 1 asia pool ntp org v Optional aen mm S e aa Figure 4 3 2 System Time Configuration 21 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 p Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Fields in System Time Field Description Current System SE l Current Time in System shown in Day Date and Time of day ime SNTP Client Tick on Check box if SNTP client has to be enabled Fields in System Time Cont d Field Description Secondary
90. k Next A screen is displayed as shown in Figure 4 6 5 7 47 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel D ptm v WAN TYPE Bridge EI Default WAN Figure 4 6 5 7 Bridge WAN Setting The screen contains the following details Fields in Bridge Configuration Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 6 5 6 Delete This option allows to delete the selected configured WAN connection This makes WAN connections free to re choose the type of protocol and other parameters configuration Click Cancel to exit from this page without saving the changes Click Apply for deleting the WAN connection 4 6 6 WAN Status To display the status report of VCCs click the WAN Status link WAN WAN Status on the left navigation bar A screen id displayed as shown in Figure 4 6 6 48 e RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 WAN Status WAN Channel Connection Status Connectio
91. k the LAN Switch Port Setting link LAN gt LAN Switch Port Setting on the left navigation bar A screen is displayed as shown in Figure 4 7 4 60 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de All LAN Port Setting You can specify the ethernet ports setting Users can choose Auto 10M 100M 1000M 10M Full Half or 100M Full Half made Auto Force 10Mb Half Force 10Mb Full Force 100Mb Half Force 100Mb Full LL ADDV Figure 4 7 4 All LAN Port Setting Default value is Auto 10 100 Full Half Click APPLY to save the information that has been entered Click CANCEL to exit from this page without saving the changes 4 7 5 LAN Port Status To discover the LAN Port Status in LAN network click the LAN Port Status link LAN LAN Port Status on the left navigation bar A screen is displayed as shown in Figure 4 7 5 Lan Status The following information provides a view of the current Ethernet ports status of the unit Ethernet PHY Port Status PORT 1 Link Down PORT 2 Link Down PORT 3 Link Down PORT 4 Link Up 100Mb s Ful Duplex Figure 4 7 4 LAN Port Status Example Table Input 1 Output 1 Input 2 Output 2 Input 3 Output 3 Input 4 Output 4 Input 5 Output 5 4 8 Select Route If there are multiple routers installed on your network it is necessary to configure the VDSL2 router unit s routing fun
92. kbox to enable Dual WAN support Primary WAN Selection Choose the WAN type from the drop down list For multi WAN mode supported i CPE image the dropdown will present following options ADSL2 VDSL2 Physical WAN Type xDSL Auto WAN Ethernet over MII 0 WAN Ethernet over MII 1 3G WAN and LTE WAN TC Transmission Convergence Selection Choose the Transmission Convergence from the drop down list 1 ATM TC or 2 PTM TC or 3 Auto This field is displayed only if ADSL2 or xDSL is chosen as the WAN type Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 6 2 Auto Detect Setting Auto detect feature is a fully automatic way to find and configure VC channel or VLAN channel for active WAN PHY of the device and WAN protocol for the same either PPPoE DHCP 33 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de User has to provide pool of VC channels or VLAN channels which will be probed one by one sequentially and upon successful detection of a channel WAN protocol probing will be done and configured in the device To configure the Auto Detect Config click Auto Detect Config WAN Auto Detect Config on the left navigation bar A screen is displayed as shown in Figure 4 6 2 Auto Detect Setting Auto Dete
93. les configured in system Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes When you have chosen IPv4 tab and click Add button in the Packet Filtering page a screen is displayed as shown in Figure 104 If you choose IPv6 tab and click on Add button a screen is displayed as shown in Figure 4 9 3 2 Adda packet filtering rule Akron to cesta a packet Fibenng rule thenghy conforming mae s denied access Probal ALL Source I Type SUBNET v Source IP Address Source Metmast Source Part Destinsbon IF Type SUBHET J Destination IP Address Destination Hamazi Figure 4 9 3 1 Adda Packet Filtering Rule for Firewall IPv4 68 VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 CS RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in Add a Packet Filtering Rule page Field Description Protocol To select the protocol The options available are ALL TCP rotoco UDP ICMP AH and ESP IP Address To specify the source IP address To specify the range of the source port Valid for protocols Source Port TCP or UDP only IP Address To specify the destination IP address Destination To specify the range of the destination port Valid for Port protocols TCP or UDP only Egress Interface To enable dis
94. m soar o4 Profile 17A Annex B 997 Mic A 7 Profile 17A Annex B 998 M1x B Cable Length DS Cable Length meters US Mbps Mbps meters US Mbps Mbps a mo Mr as M0 mr ww sa 4s o s um wm xs Me mm 34 156 Profile 17A Annex B 998 M2x A Profile 17A Annex B 998 M2x M Cable Length Cable Length US Mbps meters Mbps ag mo Gm ww Ian 4 amp we man ue mm xsv zm mm sser oso Profile 17A Annex B 998 M2x B Profile 17A Annex C Cable Length Cable Length US Mbps US Mbps meters Mbps meters Mbps as wo 3399 ae mo ae wm sm sm mm nl ue wm ser am mm zu 39 Profile 17A Annex C_1M1 Profile 17B Annex B 998 M2x M Cable Length DS Cable Length US Mbps US Mbps meters Mbps meters Mbps a 40 369 as 100 8098 meters xps Mbps is M0 mn ww 3 7m mm mm an wm ena mm 20s oss 104 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Profile 17B Annex B 998 M2x B Profile 30A Annex A M1_EU32 Cable Length DS Cable Length US Mbps US Mbps meters Mbps meters Mbps a m 339 as 100 m Cable Length DS Cable Length US Mbps meters p meters 105 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking
95. n Type Name 1 e d PTM VLAN 201 PPPoE UNCONFIGURED Unconfigured Unconfigured WANPPP1 Gateway Information DNS Information Primary Secondary u Figure 4 6 6 WAN Status The screen contains the following details Fields in WAN Status Field Description IPv4 IPv6 Choose the appropriate tab to view the status For the currently configured WAN interface this gives the layer 2 WAN Channel WAN channel information such as ATM VCC The type of the connection mode in which VC 400RT is Connection Type l configured Displays the connection status of the WAN An Displays the IP address in use Configured Connection Name Displays the configured connection name Gateway Information Provides information about the gateway DNS Information Provides information about the primary and secondary DNS The control buttons shown against few WAN are explained below Fields in Control Fields displayed in WAN Status Screen Field Description button it tries to establish PPP link this button it brings down the PPP link to establish renew the current lease to release the current lease 49 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de When you click on the IPv6 tab in the WAN Status page a screen is displayed as shown in Figure 4 6 6 1 WAN Status ZE y f FIM Soen PPPoE UNCONFIGURED UNCONFIGU
96. n also prevent hacker attacks by mapping local addresses to public addresses for key services such as the Web or FTP 9 Enable Disable Figure 4 10 1 Network Address Translation NAT Settings The screen contains the following details Fields in Network Address Translation Click Apply for activating or deactivating the NAT feature Click CANCEL to exit from this page without saving the changes 4 10 2 Virtual Server To configure the virtual server click the Virtual Server link NAT Virtual Server on the left navigation bar A screen is displayed as shown in Figure 4 10 2 74 VC 400RT Managed VDSL2 CPE Router MANUAL Ver Virtual Server A 5 RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de e You can configure the CPE device as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses In other wards depending on the requested service TCP UDP port numbers the CPE device redirects the external service request to the appropriate server located at another internal IP address Application Name Skype UDF at 1 192 1068 16 21 31082 192 168 16 21 2382 Skype TCP at 2 192 168 16 21 31082 192 168 16 21 2382 Skype LIDP at 3 192 168 16 16 49285 192 168 16 16 2382 Skype TCP at 4 192 168 16
97. n ms for the interval to send F5 loopback Interval time cells Number of Tx cells Count to total number of transmitted ATM cells Click Test to view the OAM F5 results When you test the OAM Configuration the F5 result is displayed as shown in Figure 4 6 9 1 and this may be a failure or successful OAM F5 result OAM F5 Ping Successful VPI VCI 0 35 Cells Tx 5 Cells Rx Cells Not Rx 5 Max Resp Time d Min Resp Time 0 Avg Resp Time millisecs 0 Figure 4 6 9 1 Test Successful 53 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de OAM F5 Ping Failed VPI VCI U Cels Tx Cells Rx Cells Not Rx Max Resp Time Min Resp Time Avg Resp Timelmilisecs Figure 4 6 9 2 Test Failed Ld mn oo tn c tn The screen contains the following details Fields in ADSL OAM F5 Test Page Field Description VPI VCI Displays the selected VPI VCI channel of the OAM F5 Setting Table Cells Rx Count of total number of received ATM cells Max Resp Time Displays the maximum response time in milliseconds Avg Resp Time milisecs Displays the average response time in milliseconds 4 7 Select LAN When connecting the VC 400RT to a new control PC one may want to go through the following steps in order to make the IP address previously set by ifconfig in the console or on some later occasion one may want to change i
98. ne can work on the power cord DO NOT install nor use your device during a thunderstorm There may be a remote risk of electric shock from lightning DO NOT expose your device to dampness dust or corrosive liquids DO NOT use this product near water for example in a wet basement or near a swimming pool Connect ONLY suitable accessories to the device Make sure to connect the cables to the correct ports DO NOT obstruct the device ventilation slots as insufficient air flow may harm your device DO NOT place items on the device DO NOT use the device for outdoor applications directly and make sure all the connections are indoors or have waterproof protection place Be careful when unplugging the power because may produce sparks Keep the device and all its parts and accessories out of children s reach Clean the device using a soft and dry cloth rather than liquid or atomizers Power off the equipment before cleaning it This product is recyclable Dispose of it properly RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Table of Contents Table of Contents eec WEE FOREWORD VDSL2 ROUTER SOLUTION SAFETY WARNINGS iiaiesseseseseneisisiarerersiitiratatektkt kinat atn raktra Marara ENENEEA NANA EAESEEEEANAESEAEEEEEEAEAEAEA ENEE EEE EAEE EE ESENE EEEE EEE UN ele EE FEHL GAP INSTALLING THE R
99. nostic Test Suite link Diagnostics Diagnostic Test Suite on the left navigation bar A screen is displayed as shown in Figure 4 15 1 Diagnostic Test Suite This page allows you to diagnose LAN and V AN connectivity of the system Physical Link Status WAN Down LAN 1 Down LAN 2 Down LAN 3 Up LAN 4 Up LAN Connectivity of CPE Testing LAN connection Pass Testing Internet Connectivity Ping to Gateway Fail Ping to Primary DNS Fail Start Diagnostics Test Figure 4 15 1 Diagnostic Test Suite The screen contains the following details Fields in Diagnostic Test Suite Field Description Connection Status WAN DSL WAN State ENET LAN O Ethernet LAN Port 0 state ENET LAN 2 Ethernet LAN Port 2 state LAN Connectivity of CPE Testing LAN Connection Testing xDSL Connection Status of LAN connection Diagnostics Testing xDSL Synchronization xDSL Synchronization Test Testing ATM Connection on default WAN ATM PVC Testing ATM OAM F5 End to End Ping Testing Internet Connectivity F5 end to end ping test Ping to Gateway Ping to Gateway IP address otart Diagnostics Test Initiates the Diagnostics test Note Please wait few seconds to show the test result 94 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 e Deutschland GmbH Networking amp Communications www rubytech de info rubytech de pm Cable Requirements A 1 Ethernet Cable A CAT 3 7 UTP unshielded twisted pair
100. obal IPv6 is enabled in CPE Fields in IPv6 Setting IPv6 Setting Enable IPv6 functionality in CPE Click Apply at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 4 14 2 6RD Configuration The VC 400RT supports IPv6 transition mechanism defined in 6rd RFC 5569 To configure the 6RD configuration click the 6RD configuration link IPv6 6RD Configuration on the left navigation bar A screen is displayed as shown in Figure 4 14 2 6RD Configuration 6rd is a mechanism to facilitate IPv6 rapid deployment across IPv4 infrastructures of Internet service providers ISPs General Settings Enable 6rd tunnel IT WAN Interface select interface v Configuration Modes MTU min 1280 ne Jo 1280 is recommended while con prine oe nternet 6RD Comcast etc as per RFC 2460 Section 5 Packet Size Issues Otherwise to get default MTU leave this field blan Static Parameters 6RD Prefix 6RD Prefix Length 6RD BR IP IPv4 Mask Length a GLa Ge Figure 4 14 2 6RD Configuration VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 The screen contains the following details Fields in 6RD Configuration Field Description General Settings CS RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Enable 6rd To enable or disable 6rd functionality in CPE tunnel Configuration select
101. ow includes the sub menus of LAN and WAN A screen is displayed as shown in Figure 4 4 Statistics P LAM WW AT Figure 4 4 Statistics in the left navigator bar 4 4 1 LAN To get the LAN Statistics click the LAN link Statistics LAN on the left navigation bar A screen is displayed as shown in Figure 4 4 1 COL LAN Statistics Statistics gt The LAN Statistics gives the per interface statistics on the LAN side LAN z WAN Interf TX RX nterface xDSL Dropped Dropped WAN gt etho 477 239420 0 0 515 58102 0 0 LAN gt Route gt Firewall gt Ethernet Ports Statistics NAT gt QoS gt Port TX RX Multicast gt IPsec gt 1 0 0 0 0 IPv6 gt Diagnostics gt 2 0 0 0 0 Quick Setup 3 2088 604587 515 67372 Home 4 0 0 0 0 Logout Help Figure 4 4 1 LAN Statistics 20 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info amp rubytech de The screen contains the following details Fields in LAN Statistics Field Description Interface Name of LAN Interface e g ethO usbO etc Receive Counters Total packets received from this interface Total bytes received form this interface Total Errorneous packets on this interface Total Dropped packets on this interface 4 4 2 WAN To get WAN Statistics click the WAN link Statistics WAN on the left navigation bar A screen is displayed as shown in Figure 4 4
102. rigger Port End Range In case of one port the end and start both are Port same p Start External Port Start range Open Protocol Protocol to be opened from external input TCP UDP or TCP UDP Add a Port Triggering entry Click Cancel to exit from this page without saving the changes T1 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info amp rubytech de When you click Add button in the Port Triggering page a screen is displayed as shown in Figure 4 10 3 1 Configure Port Triggering Some applications such as games video conferencing remote access applications and others require that specific ports in the Rauter s firewall be opened for access by the applications You can configure the port settings fram this screen by selecting an existing application or creating your own Custom application and click 5Save Apply to add it Application Name S Select an application Select One v Custom application Trigger Port Trigger Port Trigger Open Port Open Port Open Start End Protocol Start End Protocol TCP v TCP wl EH Figure 4 10 3 1 Port Triggering Add The screen contains the following details Fields in Port Triggering Field Description Application T Port Triggering Application Name Trigger Trigger Port End Range In case of one port the end and Port End start both are same
103. s performance is equal to ADSL2 ADSL like long reach performance is one of the key advantages of VDSL2 LR VDSL2 enabled systems are capable of supporting speeds of around 1 4 Mbit s downstream over distances of 4 5 km 2 5 3 miles gradually increasing the bit rate up to symmetric 100 Mbit s as loop length shortens This means that VDSL2 based systems unlike VDSL1 systems are not limited to short local loops or MTU MDUS only but can also be used for medium range applications E 107 DS RUBY Deutschland GmbH Networking amp Communications www rubytech de info rubytech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Signal to noise ratio often abbreviated SNR or S N is a measure used in science and 3 engineering that compares the level of a desired signal to the level of background noise It is defined as the ratio of signal power to the noise power A ratio higher than 1 1 3 indicates more signal than noise While SNR is commonly quoted for electrical signals it can be applied to any form of signal such as isotope levels in an ice core or biochemical 3 signaling between cells The ratio is usually measured in decibels dB The Answer signal to noise ratio the bandwidth and the channel capacity of a communication channel are connected by the Shannon Hartley theorem In digital communications the SNR will probably cause a reduction in data speed because o
104. service provider in any of the following ways Attached Channel 1 ptm0 201 v WAN TYPE Dynamic IP Address iv Dynamic IP Address Static IP Address PPPoE Bridge Default WAN L Help Figure 4 6 5 2 WAN Settings Apply Step1 4 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in WAN Settings Apply Step1 Field Description Select the WAN Channel e g PVC from drop down being configured as WAN Attached Channel To enter the WAN interface IP Address of VC 400RT enable this field Static IP Address l and click Apply Point to Point Protocol over ATM used for connecting to the ISP click Apply This setting is applicable only for ATM WAN mode Click Apply at any time during configuration to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 6 5 1 Dynamic IP Address To configure the WAN interface of DHCP IP type select Dynamic IP Address option A screen is displayed as shown in Figure 4 6 5 3 WAN The CPE device can be connected to your service provider in any of the following ways Attached Channel 4 ptm0 201 v WAN TYPE Dynamic IP Address v Address Version IPv4 IPv6 WAN IPv6 Configuration Configuration Modes Stateful DHCPv6 IA_NA and l PD
105. set click on the Reset button below You will be asked to confirm your choice The reset will be complete when the power light stops Administrator Settings blinking Some times the device may be corrupted by faulty configurations in such a state you can bring the CPE device back to factory default configuration settings by clicking the Factory Reset button By pressing Factory Reset all user configurations are replaced with Web Settings factory default configuration settings Software Firmware Upgrade Configuration Settings System Log Factory Reset SSL Certificate oo a Figure 4 3 9 Reset Click Reset to reboot the system This does not change the configurations existing in system Click Factory Reset to reset the device configuration to factory defaults configuration This operation will result in saving the current configuration and reverted back to factory shipped configuration 28 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Q Deutschland GmbH Networking amp Communications www rubytech de info rubytech de When Reset or Factory Reset is clicked a confirmation message is displayed as shown in Figure 4 3 9 1 2 Do you really want to perfanmn this operation on CPE 7 Figure 4 3 9 1 Reset Confirmation Message Click Ok to perform the operation on CPE Click cancel to exit from this page 4 4 Select Statistics Select the Statistics link on left navigation menu The menu bel
106. software version Figure 4 8 3 1 Routing List IPv6 Tab 4 9 Select Firewall You can view Firewall link on the left navigation ba of the VC 400RT CPE homepage The menu below includes the sub menus of Firewall Setting IPv6 Firewall Setting Packet Filtering URL Filtering Parental Control Application Server Settings and ACL Following are the options available under Firewall as shown in Figure 4 9 65 RUBY Deutschland GmbH VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 gt Networking amp Communications www rubytech de info amp rubytech de Firewall Firewall Setting IPv6 Firewall Setting Packet Filtering URL Filtering Parental Control Application Server Settings ACL Figure 4 9 Firewall Options 4 9 1 Firewall Setting To enable or disable the firewall click the Firewall Setting link Firewall gt Firewall Setting on the left navigation bar A screen is displayed as shown in Figure 4 9 1 Firewall Setting The CPE device provides extensive firewall protection against a wide array of common hacker attacks This is done by restricting connection Parameters to limit the risk of intrusion O Enable 9 Disable Figure 4 9 1 Firewall Setting The screen contains the following details Fields in Firewall Setting Description Click APPLY at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes 4 9
107. t again without using the console then the menu below will be helpful In order to set the IP address click on LAN Settings You can view LAN in the left navigation bar for LAN related settings Select the LAN The menu below includes the sub menus of LAN ARP List LAN Settings and UPnP Devices A screen is displayed as shown in Figure 4 7 LAN ARP List LAN Settings UPnP Devices Figure 4 7 LAN options 54 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de 4 7 1 LAN ARP List To view the ARP entries list that is currently present in CPE click the LAN ARP List link LAN LAN ARP List on the left navigation bar A screen is displayed as shown in Figure 4 7 1 ARP List The ARP list allows you to see which clients are connected to the CPE device via IP address and MAC address MAC Address IP Address HW Type O0 1f d0 a0 5c 2c 192 168 16 9 x1 DCc ae c5 56 13 le 192 168 16 16 x1 Figure 4 7 1 ARP List The screen contains the following details Fields in LAN ARP List Field Description MAC Address MAC Address of next hop node from ARP entry Hardware Type for ARP entry 0x1 corresponds to IEEE 802 3 ethernet based interface Click Perform ARP Scan to ensure the ARP entries connected to the CPE 4 7 2 LAN Settings To configure the LAN interface click the LAN Settings link LAN L
108. tech de 4 3 5 Software Firmware Upgrade To update the system firmware click the Software Firmware Upgrade link System gt Software Firmware Upgrade on the left navigation bar A screen displays the current version of VC 400RT Software running on the device as shown in Figure 4 3 5 Software Firmware Upgrade Host Name Config Specify the path and name of the image file to be upgraded and click the APPLY button below You will be prompted to confirm the System Time upgrade After the upgrade process it will boot the system Administrator Settings Web Settings Software Firmware Upgrade Configuration Settings System Log SSL Certificate Figure 4 3 5 Software Firmware Upgrade Click Browse to specify the software image file from host to be upgraded in system Click Apply to start the software upgrade process Note Regarding the software current version that you can click home on the left navigation bar to view 4 3 6 Configuration Settings To manage the configuration of the system click the Configuration Settings link System gt Configuration Settings on the left navigation bar This page allows users to backup the current configuration of CPE to host PC or restore the previously backed up configuration in host PC to CPE as displayed in Figure 4 3 6 ETT Configuration Settings Host Name Config You can manage the CPE device configuration settings The current configuration of CPE devi
109. tion Local Domain Name optional To enter the Domain Name of the DHCP server DHCP Server IP IP address of the DHCP server on the interface shown to which the DHCP requests are relayed 56 Deutschland GmbH Networking amp Communications ech de VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Field Description DHCP Mode DHCP Server DHCP IP Pool Starting Address Server IP Pool Ending Address Lease Time Half haur Local Domain Name dslaw lantiq com optional IP Pool Starting DHCPv4 pool start IPv4 address Address Lease EE Lease Time for every DHCP leased entry Select from dropdown of allowed values Click APPLY at any time during configuration to save the information that you have entered Click CANCEL to exit from this page without saving the changes When you click the Click Here link under IP Address Reservation in the LAN Settings page a screen is displayed as shown in Figure 4 7 2 1 This is used for the reservation of IP address of client s MAC address in DHCP server IP Reservation IP reservation Allow static IP address assignment by DHCP server for specified MAC address HOST NAME IP ADDRESS MAC ADDRESS ENABLE I 4d unknown So o GENES Figure 4 7 2 1 IP Reservation 37 CS RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following deta
110. y Field Description Auto Detect Enable To enable Auto Detect Displays the L2 interface names over which VLAN Channel has been Base WAN Name configured VLAN interface name Select this option to delete a specific VLAN channel Click Add to save the information that you have entered Click Cancel to exit from this page without saving the changes When you click Add button inside the VLAN Channel Config page a screen is displayed as shown in Figure 4 6 4 2 Vlan Creation E Name Mode Name 4 PTM v LM ISs Override MAC Address LAM Figure 4 6 4 2 VLAN Channel Config Add 39 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 p Deutschland GmbH Networking amp Communications www rubytech de info rubytech de The screen contains the following details Fields in VLAN Creation Field Description VLAN Channel 7 User specified VLAN Channel name Name VLAN identifier in range of 7 4095 VLAN Identifiers 1 6 are VLAN Id internally used in system for special purpose and are not available to user for configuration Click Add to save the information that you have entered Click Cancel to exit from this page without saving the changes 4 6 5 WAN Setting To configure the WAN interface click the WAN Setting link WAN WAN Setting on the left navigation bar and a screen is displayed as shown in Figure 4 6 5 WAN Setting Auto Detect Enable Figure 4 6 5 WA
111. y actions to ensure the default WAN is configured In case the WAN connection is already existing in CPE device the same gets re created with newly supplied attributes from the user The default WAN Setup configuration shows the Bridged status Quick Configuration of default WAN connection ta Service Provider s network Default WAN Connection Setup Channel VlanId 201 Connection Type Bridged v Configure d Figure 4 1 2 1 WAN setup Bridged The screen contains the following details Fields in Home page Field Description Specify VLAN Id Reserved or internally used VLANs that can not be configured Channel Vlanld l l in Quick WAN Setup are listed Click Configure to configure the default WAN connection setup 17 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de Quick Configuration of default WAN connection to Service Provider s network Default WAN Connection Setup Channel VlanId 201 Connection Type Figure 4 1 2 2 WAN setup Dynamic IP The screen contains the following details Fields in WAN setup Dynamic IP Field Description Channel Vlanld Specify VLAN Id Click Configure to configure the selected WAN connection setup Quick Configuration of default WAN connection to Service Provider s network Default WAN Connection Setup Channel VlanId 201 Connection Type Username
112. your equipment If they do you will be notified in advance in order for you to make necessary modifications to maintain uninterrupted service This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs 111 RUBY VC 400RT Managed VDSL2 CPE Router MANUAL Ver A5 2 Deutschland GmbH Networking amp Communications www rubytech de info rubytech de FCC Warning This equipment has been tested to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment can generate use and radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at owner s expense CE Mark Warning This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning al Bif To avoid the potential effects on the environment and human health as a result of the presence of E N hazardous substances in electrical an

NVF-200LS/RS User's Manual - RubyTech Deutschland GmbH

Contents

Download Pdf Manuals

Related Search

Related Contents