USER MANUAL AD110 and AD111 pH/°C and pH/mV/°C Meters
Contents
1. Turn ON by pressing the ON OFF 6 S key E Remove the protective bottle from the pH electrode tip Immerse pH electrode and temperature probe in the solution to be tested stir gently and wait for stable reading 9 Note The pH electrode tip should be submersed at least 4 cm into the solution Note The temperature probe should be located as near as possible to the pH electrode Press the SET HOLD key to display the desired range pH mV only for E AD111 with the proper electrode or C temperature pH readings are automatically compensated for temperature variations e If the temperature probe is not connected the compensation is done at a fixed value of 25 C the C tag blinks to advise the operator e To freeze the display from measurement mode press and hold the SET HOLD key until the H tag lights up e Press SET HOLD again to return to normal mode e After use turn the meter OFF by pressing ON OFF and disconnect the probes Cow 10 e Clean the pH electrode with water and insert the tip protection bottle Never let the electrode tip dry See Electrode Maintenance paragraph page 15 for details 11 CALIBRATION The instrument is factory calibrated for mV and temperature ranges Contact your dealer for re calibration if necessary For pH calibration proceed as follows Enter the calibration mode by pressing2. CAL key 7 01 pH will start blinking e For a single point calibration im merse pH electrode and temperature probe in any of the memorized buffers e g pH 4 01 7 01 or 10 01 The meter automatically recognizes and displays the buffer value e When the pH tag stops blinking press ED SET HOLD to confirm the calibration kr point 12 Note If the pH 7 01 buffer was used press SET HOLD again to exit the calibration mode Otherwise if a different buffer was used the meter automatically returns to normal mode For a two point calibration immerse pH electrode and temperature probe in pH 7 01 buffer A pH 7 01 Eg The meter automatically recognizes and displays the buffer value 1 p m When the pH tag stops blinking press SET HOLD to confirm and store the first calibration point The meter will then ask for the second buffer Immerse pH electrode and temperature probe in pH 4 01 or pH 10 01 buffer 13 e When also this buffer is recognized press SET HOLD to confirm and So store the second calibration point the kst meter will return to normal mode Note Note Note Note If a solution with wrong pH value 1s used as buffer for calibration the LCD displays the Ec message To exit the calibration mode press CAL at any time The meter will display dashes and then return to normal measurement mode e To reset to the defaul
3. 0 C 1000 mV Resolution 0 01 pH 0 1 C 1mV Accuracy 25 C 0 02 pH 0 5 C up to 60 C 1 C outside 2 mV pH Calibration Automatic 1 or 2 point with 3 memorized buffer values pH 4 01 7 01 and 10 01 mV Calibration Factory Temp Calibration Factory Temp Compensation Automatic or 25 C fixed Battery Type Life 4x 1 5V AA approx 1500 hours of use Auto off After 8 minutes of non use Environment 0 to 50 C RH max 95 Dimensions 70 x 145 x 26 mm Weight Approx 200 g DISPLAY AND KEYBOARD FUNCTIONS l N sy AD 111 10808 pH mV C Meter Display 1 H symbol lights up to indicate that the reading is frozen on display 2 Battery symbol lights up to indicate a low battery condition 3 Measure unit of the displayed reading pH mV AD111 only or C Keyboard 4 ON OFF key to turn the instrument ON and OFF 5 SET HOLD key to select measurement range confirm calibration points and freeze reading on display keep pressed 6 CAL key to enter exit calibration mode MEASUREMENTS Each instrument is supplied complete with four 1 5V batteries Install the batteries as explained in the Battery Replacement paragraph see page 14 Attach pH electrode and temperature probe to the connectors on the top of the instrument Temperature i BNC connector for probe connector pH or ORP electrode
4. USER MANUAL AD110 and AD111 pH C and pH mV C Meters poes www adwainstruments com Dear Customer Thank you for choosing an Adwa product Please read carefully this manual before starting Operations This instrument is in compliance with the EMC Directive 89 336 EEC and Low Voltage Directive 73 23 EEC for electrical equipments For additional technical information please e mail us at sales Oadwainstruments com TABLE OF CONTENTS Introduce 5 Technical Data neues sen 6 Display and Keyboard Functions T Measurements nissen 9 Carat illes 12 Battery Replacement anornnonnnonnnvnenvnenerenevevensnvrnnene 15 Electrode Maintenance rrrernrnnnnrrvennrnennrnvenrnervrerenr 16 Probes and Solutions ooocoonicccnonocinncnononcnnnncnancnonnnanns 17 Noter dad ee 19 INTRODUCTION AD110 and AD111 are compact pH meters featuring automatic pH calibration hold function low battery indication temperature measurement and compensation In addition AD111 can measure in the mV range if using proper electrode Both models are supplied complete with e AD1230B pH electrode with Epoxy body tip protection bottle BNC connector and 1 m cable e AD7662 stainless steel temperature probe 1 m cable e pH 4 01 and pH 7 01 calibration buffers 20 ml sachet each Batteries 4 x 1 5V AA alkaline Instruction manual TECHNICAL DATA AD110 AD111 Range 2 00 to 16 00 pH 5 0 to 105
5. t values after entering the calibration mode and before the first point is confirmed pH tag is blinking press and hold the SET HOLD key and then CAL E Ce For better accuracy it is recommended to carry out a 2 point calibration procedure 14 BATTERY REPLACEMENT When the batteries become weak the battery symbol on the LCD lights up 450 When the low battery indicator appears only a few hours of battery life is remaining It is recommended to replace the batteries immediately In addition when the battery level is too low to ensure reliable readings the Battery Error Prevention System BEPS warns the user by displaying the Eb message and then switches the instrument off To replace the batteries remove the battery compartment cover on the rear of the instrument and replace all four 1 5V AA batteries while paying attention to their polarity Batteries should only be replaced in a safe area and using the battery type specified in this instruction manual 15 ELECTRODE MAINTENANCE Storage To minimize clogging and ensure a quick response time the glass bulb and the junction of the pH electrode should always be kept moist When not in use store the electrode with the tip protective bottle If you need to add some solution to the tip protective bottle use the AD70300 storage solution Periodic Maintenance Inspect electrode and cable The cable used for the connection to
6. the instrument must be intact and there must be no points of broken insulation on the cable or cracks on the electrode stem or bulb If any scratches or cracks are present replace the electrode Rinse off any salt deposits with water Connectors must be perfectly clean and dry Cleaning Procedure Soak in deionized water for approximately 30 minutes then rinse the electrode thoroughly with deionized water and soak it in AD7061 cleaning solution for at least 1 hour before taking measurements 16 PROBES AND SOLUTIONS AD1230B AD3230B AD7662 AD70004P AD70007P AD70010P AD70300 AD7061 pH electrode with Epoxy body tip protection bottle BNC connector and I m cable ORP electrode with Epoxy body tip protection bottle BNC connector and I m cable Stainless steel temperature probe with I m cable pH 4 01 buffer solution 20 ml sachet 25 pcs pH 7 01 buffer solution 20 ml sachet 25 pes pH 10 01 buffer solution 20 ml sachet 25 pcs Sorage solution 230 ml Cleaning solution 230 ml 17 NOTES 19 ADWA INSTRUMENTS Kft Als kik t sor 11 6726 Szeged Hungary Tel 36 62 317 878 Fax 36 62550610 e mail sales adwainstruments com www adwainstruments com MANAD110 09 14
Download Pdf Manuals
Related Search