JEM K1 Hazer user manual
Contents
1. m 14 Remote contol u a A Nan a 15 S Ke EM e e Dan Ga O e vali 15 BE E AN Ee yn e ire ME E ki NA 15 a ee gk ye u EE EE ide 16 OVEIVIGW u u gk a ama say map alak nadasa gara galas alada Sl salak 16 CONNECCION saa ag ikke Yarda sal a aa aa do sa l aliya dukan Sasi 16 DMXTUMG ONS kaaran aa kk a AAA SR ani ba het la ela 16 KOYLU Y esasi elemli a eek iski ta aa inga ek 17 BaSIC lt lt a u uu aa aa qewa a aana ga aa Adee eugene WA dara kar da naa aa eevee 18 CAEN A Rae A daga a las Oe aa Ta a 18 Fuse replace ment sas satan Ani een a ane Gv hee L O 18 Troubleshooting usa aa NG t L KAN AKNG Wa ay Bea vag a fae deve aa KAN ada a a BA du lada Gl dada ede 19 Status MOSSAGES rl anang a gk aaa 20 SP GINGAHONS uu t aynin et a ieee sela eee en eat eed 21 A es tuta aS Aca teeth tel a te tia tii ti 23 2 Safety information Safety information The following symbols are used to identify important safety information AAAA Caution Safety Caution Burn Danger Caution Fire hazard Risk of hazard Hot Hazardous hazard personal injury surface Do not voltage Contact touch will cause electric shock Warning This product is not for household use It presents risks of injury due to electric shock burns falls and respiratory problems Read this manual before operating the machine follow the safety precautions listed below and observe all warnings in this manual and printed on the machine Use the system2. e Timer run time off time settings TRUN TOFF 0 90 seconds e Run mode RUN OFF STBY FAN TIME CONT The functions are the same as on the built in control panel and are described on page 11 The Haze button works by setting RUN to CONT or STBY The Timer button sets RUN to TIME or STBY These buttons are simply a quick way to control this menu function Remote control 15 DMX control 16 Overview DMX is a digital control system widely used in entertainment and architectural lighting Any controller meeting the DMX 512 standard may be used to control and program the haze output of the JEM K1 Hazer When a DMX signal is present the JEM K1 Hazer M s stand alone functions do not work To fire the unit from the contro panel or remote control the DMX controller must be powered off or disconnected Connection The JEM K1 Hazer provides both 3 pin and 5 pin XLR sockets on the rear panel of the machine for DMX connection The sockets are interconnected a DMX line connected to the 3 pin IN socket may be continued through the 5 pin OUT socket and vice versa Do not however attempt to split a DMX line by using both the 3 pin and 5 pin OUT sockets For best results use cable designed for high speed digital data transmission Suitable DMX cable is available from your Martin dealer DMX functions The JEM K1 Hazer M s address setting must match the DMX address allocated to it on the controller To set
3. Preventing breathing problems e A haze machine can operate safely only with the haze fluid it is designed for Use the machine only with the fluid specified under Haze fluid options on page 17 or you may cause the release of toxic gases presenting a severe health hazard You will also probably damage the machine e Do not create dense haze in confined or poorly ventilated areas e Do not expose people with health problems including allergic and or respiratory conditions such as asthma to haze output e Do not point haze output directly at a person s face or at face height Safety information 5 Product overview The JEM K1 Hazer from Martin is a top of the range solution to a wide variety of atmospheric requirements whether permanently installed or taken on the road Featuring a revolutionary new block design and a high volume radial blower the JEM K1 Hazer can quickly produce large volumes of haze to create large scale effects in the biggest venues Congratulations on your purchase of the JEM K1 Hazer from Martin Details of the full range of Martin products are available on our website at www martin com Features at a glance Attractive and rugged design High speed radial blower Revolutionary block design for high output and reliability Control panel with alphanumeric display Optional full function digital remote with display 25m max cable length Carrying handles DMX control 2 channels Standby
4. When you turn off the power the unit will switch to its backup battery and enter a 3 minute shutdown procedure This clears the block of any residual fluid to prevent clogging During shutdown the display shows WT with a countdown 8 Quick Start Installation and setting up A DANGER DO NOT operate the JEM K1 Hazer until you have read and observed all the precautions listed under Safety information on page 3 The JEM K1 Hazer should be located on a solid surface such as the floor The machine can operate in any orientation from 45 degrees upwards to 45 degrees downwards Steeper tilting may cause fluid leakage Do not suspend the machine over areas where people will be underneath Ensure that there is at least 100mm clearance all round the machine and at least 600mm in front of the haze output Before using the machine ensure that a grounding type earthed power plug that fits the local power outlets is installed on the power cable DANGER Make sure the power plug is correctly rated lt For EU 230V use fit a plug rated 6 amp minimum e US 120V models must be fitted with a plug rated 10 amp minimum When installing the plug follow the plug manufacturer s instructions and connect pins as follows yellow and green wire to ground earth blue wire to neutral and brown wire to live The table below shows some common pin identification schemes wire function marking screw colour brown live
5. battery runs shutdown procedure after power down Product overview Product details Digital control Quick access panel buttons 3 pin DMX input and Remote control 6 j socket 5 pin DMX h input and o e link Main power l switch A Power inlet connector External fuse Flying kit eyelet mounting points x4 Air intake Fluid tank Haze output nozzle Warning high temperature vapour and surfaces Product overview 7 Quick Start You are no doubt eager to switch on the machine and try it out by making a lot of haze This section tells you how to do that However please also make the time to read the safety and servicing instructions in the remainder of this manual Locate the machine in a suitably large area with nothing in front of the haze output Fill the fluid tank with MARTIN approved haze fluid see page 17 Connect a suitably rated power supply to the machine The power requirements are 6 3A at 230V EU or 10A at 120V US If you are using the optional remote control connect it to the REMOTE IN connector on the rear panel Y i Turn on the Standby switch The display will show H f T for about 5 7 minutes and will then change to Ki Y Ready Making haze Once the machine has heated up press the HAZE button on the remote to start the haze output or press one of the four Quick Access buttons on the onboard control panel Shutting down
6. only as described in this manual and in accordance with local laws and regulations If you have questions about how to operate the machine safely or if you have followed the instructions in this manual and the machine is malfunctioning please contact Martin Service Preventing electric shocks Always ground earth the machine electrically Use only a source of AC power that complies with local building and electrical codes and that has both overload and ground fault protection Before connecting the JEM K1 Hazer to power check that the voltage indicated on the machine s serial label matches your local AC power voltage If your AC power voltage does not match do not use the machine Contact Martin Service for assistance Before using the machine check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices If the machine or any cables connected to it are in any way damaged defective wet or show signs of overheating stop using the machine and contact Martin Service for assistance If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or it s service agent Disconnect the machine from AC power before servicing and when not in use This system is not waterproof and should not be exposed to wet outdoor conditions Do not immerse in water or any other liquid Do not expose to high pres
7. the address see Setting the DMX base address on page 12 The JEM K1 Hazer requires two DMX channels DMX channel function Haze density 0 100 NM Fan speed 0 100 and Shutdown Channel 1 uses the full range 0 255 for fog density control Channel 2 has the following control values DMX value function 0 244 Fan speed 0 100 heaters on 245 255 machine shutdown heaters off For example if the JEM K1 Hazer is set to DMX address 100 channel 1 will be controlled by address 100 and channel 2 will be controlled by address 101 When the machine is at running temperature and is under DMX control it T M V displays IMA DMX control Fog fluid types A The following type of Martin fog fluid is suitable for use in this machine Martin supplies high quality fog fluids that are based on ultra pure deionized water Use only the following genuine Martin fog fluid No other fluid is suitable for use DANGER The JEM K1 Hazer can run safely only on the specific haze fluid it is designed for Use ONLY the Martin haze fluid designated in this manual NEVER use any other type of fluid or toxic gas may be produced You will probably also cause damage to the system that is not covered by the product warranty Do not dilute haze fluid with water or any other liquid Discard haze fluid if it becomes contaminated JEM K1 Haze Fluid JEM K1 M fluid is a light molecular fluid which generates an invisible c
8. 000 6 3 2001 Part 6 3 European safely uy u ita aranan aaa aa Na a a qa usaq sasa EN 60 335 1 2002 A EN 61000 6 1 2001 Part6 1 ETL approvals CETLus pending UL60335 1 CSA E60335 1 Specifications 21 22 Included items EU Model 2m 6 56ft power cable 3x1 0mm with POWERCON male connector US Model 1 8m 6ft US power cable 18AWG with US male connector UL approved 1 x fluid container empty Ordering information Martin JEM Ki Hazer 120V anno nn conocio nn nono nane n nana 92225900 Martin JEM Ki Hazer 230V nn conocio nan n nane anane 92225901 JEMK1 Mdigitalremotecontrol 92765036 FiyingkKitfforMarinJEMK1HazerM XXXXXX Specifications Notes Notes 23 g Martin Martin Professional A S Olof Palmes All 18 DK 8200 Aarhus N Phone 45 87 40 00 00 Internet www martin com
9. L yellow or brass blue neutral N silver green yellow earth e green Before connecting the JEM K1 Hazer to power verify that the AC supply is adequately dimensioned for the current draw of the machine The machine requires 6 3A at 230V EU or 10A at 120V US Check that the local AC voltage is appropriate as indicated on the machine s serial number label If your AC voltage is outside the appropriate range do not use the machine Contact Martin Service for assistance Fill the fluid tank with Martin approved fluid see page 17 Installation and setting up If DMX control is being used connect the machine to the DMX line see page 16 If the JEM K1 Digital Remote is being used optional accessory connect the remote to the Remote socket See page 16 Final checks Before applying power to the JEM K1 Hazer verify the following e the machine is safely located or installed and meets the location requirements stated on page 9 e the operator is familiar with and able to comply with the requirements for safe operation listed on page 3 e the haze fluid is genuine Martin fluid listed under Haze fluid options on page 17 e the machine is electrically grounded earthed e the AC power distribution circuits and lines are adequately rated for the current load Turning on the power Turn on the main power switch located next to the power cable inlet The display will show HE HT for abo
10. P N 35010031 C JEM K1 Hazer user manual h Marti SaletyInformationi nae han ee alana td le ANG eo l 3 Product Ovet viS W sisle unum daa di aapa daa aa NA i aa gah S i aqtuy aan 6 Product d Scription p kaa Pa na Su u NAK Nga na da Ae ANAA G re ee Ema asah ati an 6 Features ata glance iti acai Rat el eet ee ev Gee ee Ae agahan 6 Product details u aba Na iene a aaa dA A sola te devas 7 QUICK Starts acetic ee a a a lie Mila ee ae e 8 SON UP steelhead ralli lima yal eee ed eee ee es 8 Making haze akli dl id ban lay A 8 Shutting Wind a eae ll a ee Yaa Ay Al 8 Installattonandsettingup eee 9 Hozan we mr Ke We KEN 9 AG DOON saa alada Ane e e a bias a 9 ella ilor ie a Merv 9 Final checks er em e e ee e RE 10 Tumingonthepower KA AR KAKANG KARENAN KANEKA KA KA NGANAKAKE KENEK KA ka Aka 10 Shutting down after use U U Q a 10 Control seltimg sis wa Hace aa Na ayauya A ANE ota eni eae yle 11 Ge ie o lA 11 DEMING haze desa raaa NAN dd 11 Setting Fan speed aa kas Mr ae 12 SENA MAMA ea do ee cai 12 SEN Wen Mi eee Ei 12 Setting the DMX base address U anana nagan aana 12 Setting the master slave link mode n 13 AMCOPro e on en ee Tep 13 Priming the machine after fluid out a anana ene 13 Resetting options to factory settings
11. ans and air vents and ensure free and unobstructed air flow to and around the machine Keep the machine at least 600mm 24 inches away from combustible and heat sensitive materials Do not operate the machine if the ambient temperature Ta is below 5 C 41 F or above 40 C 104 F Do not operate the machine if the relative air humidity exceeds 80 Preventing injuries Ensure that the surface on which the machine is located or installed can safely hold the weight of the machine Do not install the machine over areas where people are present This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Haze machines can cause condensation Do not point the output at smooth floors Floors and surfaces may become slippery Check these frequently and wipe dry as necessary to avoid any danger of slipping Ensure at least 2m visibility in areas where haze is being produced Haze fluid contains food grade glycols in solution but may present health risks if swallowed Do not drink it Store it securely If eye contact occurs rinse with water If fluid is swallowed give water and obtain medical advice Safety information
12. anvas specially designed to project light beams and lasers The haze is slow dispersing with an extended long hang time Fog fluid types 17 Basic service Before servicing the JEM K1 Hazer read and observe all the precautions listed in Safety information on page 3 Any service not described in this section must be carried out by a Martin service technician Excessive dust haze fluid and dirt buildup will degrade performance and cause overheating and damage to the machine that is not covered by the product warranty To maintain adequate cooling dust must be cleaned from the outer casing and air vents of the machine periodically Isolate the machine from power and allow to cool completely before cleaning The haze output nozzle remains hot for up to 10 hours after use e Remove dust from the air vents with a soft brush cotton swab vacuum or compressed air e Clean haze fluid residues from the fog output of the machine e Clean the outer casing with a damp cloth only Error messages If the display shows ERR the machine has detected an internal fault Switch off the machine and contact Martin Service Fuse replacement The main fuse for the JEM K1 Hazer is in a fuse holder located adjacent to the power inlet To replace the fuse disconnect the power cord from the supply unscrew the cap of the fuse holder and pull out the fuse Remove the spent fuse and replace with one of exactly the same size and rating The fu
13. emote press the Timer button When the timer is running and the display is not showing a menu the O display shows a countdown for the run time RU and the off time OF Setting the DMX base address Use the Previous Next buttons to select the H 1 IF option Use the Up Down buttons to set the DMX base address from 1 4 tos i If you hold down the button the address will count up or down getting faster the longer you hold it Press the Enter button to store the address setting The machine will automatically respond to a DMX controller whenever it is connected Control settings Setting the master slave link mode It is possible to control several machines from one digital remote The machine with the remote plugged into it becomes the Master The other machines are Slaves The machines are interconnected with DMX cabling Use the Up Down buttons to select KE L v or BE N TI Press the Enter button to store the link setting Use the Previous Next buttons to select the I NK option 1 The machine should be set to SEN only if it is running as a master If running my as a slave stand alone or DMX controlled it should be set to REL Y This option is not currently used and has no effect on the machine Priming the machine If the machine runs out of fluid or you are priming a new machine use the PRIME function Use the Previous Next buttons to select the FF ME option Use the Up Down buttons to c
14. hange the option to Y Press the Enter button to start the priming function The machine will pump until it detects fluid entering the block To exit this menu if you decide not to activate the Prime function select N and press Enter If the machine is not up to operating temperature the Prime function will do nothing Control settings 13 14 Resetting options to factory settings The factory settings configure a standard mode of operation for the machine Use the Previous Next buttons to select the 4 E T option Use the Up Down buttons to change the option to Y Press the Enter button to reset all options To exit this menu if you decide not to reset the options select N and press Enter The factory settings are option setting HAZE SAN FAN SAN TRUN x TOFF ew RUN TAY LINK RELY Control settings Remote control Overview The JEM K1 Digital Remote control available separately may be used for remote control of the JEM K1 Hazer Several machines may be controlled from one remote using the LINK function see page 13 XLR socket Display XLR socket A on rear Timer button Haze button Functions The remote control provides the following functions e Haze button turns haze output on and off Press once to start haze and again to stop e Timer button turns the haze timer on and off e Haze level setting HAZE 0 100 e Fan speed setting FAN 0 100
15. nit is under DMX control RNA AA number may be 01 to 90 Machine is in timer mode counting down the run period number may be 01 to 90 Machine is in timer mode counting down the off period ET AVA WA DM number may be 90 to 00 The machine is carrying out its shutdown seguence FA al The machine has detected an error with its calibration settings and will not operate Call Martin Service gt 2 i Z al FA 1 al A The air pump is not working This indicates a fault Turn the machine off and call Martin Service gt FA 1 al A The fluid pump is not working This indicates a fault Turn the machine off and call Martin Service FA gt al FA al eq ad The heater is at too high a temperature This indicates a fault Turn the machine off and call Martin Service on startup The machine s run time has passed its recommended service interval The machine is safe to use but should be serviced as soon as is convenient on startup The internal battery is low and the last shutdown did not complete If this message displays on every startup call Martin Service to obtain a replacement battery Status messages Specifications NOTE Specifications are yet to be finalised Physical Lengi sasa ada sa u a etl aie ded dis 544mm Widths 3 el ce eee A eee da 459mm eight si suu es ices 344mm Dry weight sa
16. of three haze output levels and a SILENT mode The display shows the current setting If you press the same button again haze output will stop and the machine will go back to Ready mode SLNT mode returns to previous state Fast Access Haze and Fan settings DMX Value Equivalent Mode CH1 CH2 C RET Drops Fan levels by 30 relative to Reduce by 3096 yi ts current values of current value EL Haze 5 Fan 5 13 13 PRE Haze 50 Fan 50 128 122 PRES Haze 100 Fan 100 255 244 Setting haze density Use the Menu Previous Next buttons to select the HH ZE option Use the Up Down buttons to select the density from 4 HUM Press the Enter button to store the haze setting The display shows S T The machine will only produce haze if the RUN menu is set to TIME or CONT Or if using the digital remote if you press the Timer or Fog buttons Enter The haze setting will go back to its stored value next time the If you want to temporarily change the haze density do not press machine is powered up This applies to all options Control settings 11 12 Setting Fan speed INI Use the Previous Next buttons to select the F HN option Use the Up Down buttons to select the fan speed from Press the Enter button to store the fan setting The fan will run continuously if set above 0 and the Fan Timer or Continuous switches are On Or if using the digital remote if the RUN menu is set
17. se type is indicated on the serial number label Contact Martin Service if the fuse blows repeatedly 18 Basic service Troubleshooting Problem Machine will not produce haze when control panel or remote control Fog switch turned on Probable cause s Machine not at operating temperature Suggested remedy Wait 5 to 7 minutes Increase setting Increase setting DMX signal present Disconnect or turn off DMX controller Machine can be fired from control panel or remote control but not by DMX controller DMX address setting incorrect Change DMX address page 12 Poor connection in DMX line Check DMX cables and connections Haze output is weak Machine requires priming Prime machine page 13 Wet greasy non uniform haze output fluid drips or spits from nozzle or very loud noise when firing machine Incompatible haze fluid Use approved fluid Machine appears dead Mains fuse blown Replace fuse page 18 No power at AC cable inlet Check power cable and circuit breaker Troubleshooting 19 Status messages 20 ssage 113 reason The heaters are Off the unit is shut down fe ry gt ad The unit is heating up to operating temperature ka lt The heater is at operating temperature but Haze is not turned on kal x gt lt The heater is at operating temperature and the u
18. sure water jets Do not spill fluid over or inside the machine If fluid is spilled disconnect AC power and clean with a damp cloth If fluid is spilled onto electronic parts take the system out of service and contact Martin for advice Safety information 3 Do not remove the covers or attempt to repair a faulty machine Refer any service not described in this manual to Martin Do not operate the machine if any parts are damaged defective or missing Moisture and electricity do not mix Do not aim haze output at electrical connections or devices Preventing burns and fire The haze produced by the machine is hot enough to cause burns when it leaves the nozzle and very hot droplets of fluid escape occasionally Keep people and objects at least 1 meter 39 inches away from the haze output nozzle Do not touch the haze output nozzle during or after use it becomes extremely hot and remain hot for several hours after the machine has been shut down Haze output contains glycol a flammable alcohol that burns with an almost invisible blue flame Do not point haze output at sources of ignition such as open flames or pyrotechnic effects Do not attempt to bypass thermostatic switches fluid sensors or fuses Replace fuses only with ones of the type and rating specified in this manual for the machine Provide a minimum free space of 100mm 4 inches around the machine Provide a minimum free space of 500mm 20 inches around f
19. tisa aki A ee se eee 21 5Kg Performance ETCH COMETA iria 5000m min Operating Mesias eee lali ltd elime inek seyis lam nagka continuous War UP AIMS ea cek iser S E BEK KAN a KAG ai E BAN KEN ie ca BEN seen 5 minutes Safety device ny usa uuu iia DTP device Control and programming Control options nana nan nano cnn rn DMX digital remote DMX channelS 1 u u naa Bae a an sak Ea pusa e 2 Fluid system Gapaciy asana sa ei A e Me e aa 2 5 litre Fluid CONSUMPTION MAX sena Saka kag R NAK KA NANA GA AGA RA YANG KANGEN a EAERI 140ml hr Compatible fluids U K1 Haze Connections DMX 22 aaa AA Qa Vr ey 3 or 5 pin XLR Remote machine linK se eaaa aaa ag u mmm 3 pin XLR AG POW T aa eee aa uu cede A au ahua as IEC plug Electrical AG Voltage gu kill ati A quae Aa gaa 120V 230V 50 60Hz Main fuse 120V US version a a 10AT Main fuse 230V EU Version eaaa eaaa aana anaa aa m 5AT Power usage 120V US version 1 675W 6 0A Power usage 230V EU version 1 675W 3 1A Thermal Maximum ambient temperature Ta max 40 C 104 F Exterior surface temperature steady state at 20 C ambient 40 C 104 F Approvals European EMC EN 61
20. to FAN TIME or CONT If haze is being produced and the fan is off or set to a low speed the fan speed will be automatically increased to prevent buildup of haze at the machine output Setting Run mode TINI Use the Previous Next buttons to select the F LIN option Use the Up Down buttons to select the operating mode mode FF heater off fan off Used when the machine is to be shut down 4 Y heater on fan off The machine is to be ready but not hazing 1E enable timed pulses of haze T enable continuous haze Press the Enter button to store the Run setting When the mode is changed to UF F the unit will enter a 3 minute shut down sequence before powering down to prevent block clogging The display shows WHIT then WT with a countdown You can cancel the shut down sequence by changing the run mode back to an active state Setting the Timer If smaller amounts of haze are required the machine has an automatic timer to give timed bursts of haze You can set the Run and Off times independently between 1 and 90 seconds TINI Use the Previous Next buttons to select the T LIN or TOF F option Use the Up Down buttons to select the run or off time from seconds to Yu seconds If you hold down the button the time will count up or down getting faster the longer you hold it Press the Enter button to store the timer setting To enable timer mode switch on the Timer switch or if using the digital r
21. ut 5 7 minutes as the machine heats up to Thy operating temperature and will then change to F I Y Ready If the display shows UF F press one of the four quick access buttons to start the machine heating You can then use the remote control or the control panel to start haze production Shutting down after use When you turn off the power the unit will switch to its backup battery and enter a 3 minute shutdown procedure This clears the block of any residual fluid to prevent clogging During shutdown the display shows WT with a countdown You can also shut down the machine by setting the F LfN menu to HF F The 3 minute shutdown procedure will be activated This can be done from the digital remote or from the onboard control panel The heater fan and pump will be shut down but the machine will remain powered and can be reactivated by pressing one of the four quick access buttons Installation and setting up Control settings Overview The four quick access buttons below the digital display at the rear of the unit allow you to quickly turn the haze on or off at four different settings The digital display allows you to configure all options of the machine using menus if you need more detailed control Digital display OP Enter store button Menu previous next Value down up buttons buttons Fast Access buttons The four Fast Access buttons allow you to quickly set the machine to one
Download Pdf Manuals
Related Search