User Guide
Contents
1. Gruetzner LUBR ICUS om User Guide Lubricus Controller LUB C 1 LUB C 2 LUB C 3 LUB C 4 LUB C 1 1 24 VDC Lubricus Type C Version 06 2011 LUBRICUS Content General Information Scope of supply Overview Lubricus Controller amp Lubricus Lubrication System Type C General safety details Intended use Extent of warranty General safety information Transport and storage Installation instruction Start up Function Adjustment Flow Chart Flow chart details Overview adjustment option Activation of exits Pump specific adjustment Table pause time adjustments Table quantity adjustment Details Activation Start Stop Adjustment Functional problems error message and problems Extras Quick check function and system control Communication Interface Service Lubricus Type C with cartridge Technical data Lubricus Controller amp Lubricus Type C Mounting Lubricus Controller amp Lubricus Lubrication System Recommended tube hose length amp Disposal page 2 Gr uetzner l 13 16 16 17 20 21 22 version 04 2013 Gruetzner LUBRICUS ome General Information Thank you very much to have decided to use our Lubricus Lubrication System and Lubricus Controller Make sure that you familiarize yourself with the safety instructions of this unit and the accessories supplied with this unit This manual contains important safety information The Lubricus Lubricati2. This symbol warns of electrical voltage Safety instructions which if not complied with may endanger persons are marked specifically with the general hazard symbol This heading is used if inaccurate compliance or non compliance with the operating Instructions or specified work procedures etc may result in damage Points out special information page 5 version 04 2013 Gruetzner LUBRICUS Notes attached directly on the machine must be strictly followed and maintained in completely readable condition Qualification and training of the personnel The operation maintenance service and installation personnel must have appropriate qualifications for this work Responsibility and supervision of the personnel must be clearly defined by the end user operator If the personnel do not have the necessary knowledge they must be trained and instructed The operator must ensure that the personnel have completely understood the contents of the user information Non observance of the safety information can be dangerous Not observing the safety information can lead to danger for people environment and machines Not observing the safety information can mean the loss of any or all damage claims In special cases non observance can for example lead to the following dangers Failure of important plant functions Failure of prescribed methods of maintenance and preventive maintenance Endangering people due to electrical mecha
3. page 3 version 04 2013 4 Gruetzner LUBRICUS e Lubricus Lubrication System Ventilation Lock amp programming key The programming key is conveniently stored on top of the clear housing to remove the key for Setup or Adjustments of your Lubricus Simply turn clockwise to a E release key The point of the key is used for programming Please note Always replace the key for safe keeping SES as this also forms part of the cover 4 Connection Lubricus Controller Important remark unused exits cannot be closed and must remain open to avoid damage to the Lubricus Lubrication System Lubricus Controller Display showing adjustment values and error messages 4 Sensor for Activation and programming key F d d ON LUBRICUS Can trellar LED Status indicator Gructzner 4 Outlets for aN Connector pin M8 x 1 Connector pin M12 x 1 connection to plc power supply 24 VDC page 4 version 04 2013 Gruetzner lt LUBRICUS General safety details Everybody who is involved with the installation start up maintenance and operation of the Lubricus Lubrication System must read these instructions carefully Use in accordance with guide Lubricus Lubrication System is only allowed for industrial use Lubricus Lubrication System may only be put into service if it is integrated or attached to another machine and will be operated together with that machine Lubricus Lubrication System may only be u
4. Time between two delivery rates number of outlets for exit 1 left side of Lubricus body C Delivery rate H Time betweentwo delivery rates C Delivery rate number of outlets for exit 2 left side of Lubricus body H Time betweentwo delivery rates C Delivery rate number of outletsfor exit 1 rigth side of Lubricus body number of outletsfor exit 2 rigth side of Lubricus body H Time betweentwo delivery rates C Delivery rate number of outletsfor exit 3 left side of Lubricus body H Time betweentwo delivery rates C Delivery rate aha number of outlsts for exit 3 rigth side of Lubricus body H Time betweentwo delivery rates C Delivery rate H number of outlets for ett 4 left side of Lubricus body Ke H Time betweentwo delivery rates C Delivery rate H Time betweentwo delivery rates 8 number of outlets for exit 4 rigth side of Lubricus body E C Delivery rate Quick Check for every activated exit Switch OFF with gt version 04 2013 4 Gruetzner LUBRICUS e Flow chart details overview adjustment Lubricus Controller can be adjusted without any Lubricus unit attached Settings will stay in memory The Controller controls the Lubricus units in sequence starting at exit 1 we orange LED Function right side of Lubricus body N green LED Function left side of Lubricus body Normal Status Indication F red LED constant light failure fault error report OK green LED c
5. Type C The Lubricus Controller is equipped with a 4 pol M12x1 connector to connect to the controller of your machine for example a PLC This connector supplies power to the Lubricus units and communicates with the controller The voltage to operate and to switch unit ON and OFF is 20 30 VDC PIN 1 The Controller will be in operating mode when voltage is present The green LED is illuminated The supply voltage will be switched to exit PIN4 if there are no errors Unit OK The Controller will save the current operating parameters in memory if the supply voltage is disconnected or unit is switched OFF The unit will start again using the last parameters saved in memory The operating status will be communicated via PIN 4 and will be displayed in the integrated display of the Lubricus Controller Connector PIN assignment Lubricus Controller M 12 x 1 PIN 1 input voltage 20 30 VDC color brown PIN 2 no assignment color white PIN 3 Ground GND color blue PIN 4 Output Signal color black Details PIN 1 Peak current 24 VDC Imax approx 350 mA during pump operation typically lt 200 mA Standby current standby mode lt 20 mA Input Signal can switches ON and OFF no assignment Ground GND High operating mode OK input voltage Low 0 V error type of error shown in display of Lubricus Controller the outlet signal PIN4 can be charged with maximal 300mA Warning the exit is not short
6. circuit proof Connection Lubricus Controller Exit M8x1 4 pol to Lubricus Typ C Exit a M12x1 4 pol All special cables are available on stock in our catalogue b If customer is managing all the necessary cabling required to keep the system functional Lubricus Controller M8 PIN 1 to Lubricus unit Typ C M12 PIN 1 Lubricus Controller M8 PIN 2 to Lubricus unit Typ C M12 PIN 2 Lubricus Controller M8 PIN 3 to Lubricus unit Typ C M12 PIN 3 Lubricus Controller M8 PIN 4 to Lubricus unit Typ C M12 PIN 4 page 18 version 04 2013 LUBRICUS Gruetzner GmbH Service replacement of cartridge Lubricus Type C modell with cartridge error report E1 empty cartridge 1 Observe the safety instructions Switch off Lubricus Controller 2 Take out ventilation locking turn clock wise to OPEN 3 Press the housing turn left and remove it 4 Remove the empty cartridge 5 Remove protection from the new cartridge 6 Lubricate O Ring of the new cartridge slightly 7 Place the cartridge on the inlet page 19 el version 04 2013 Gruetzner LUBRICUS ome 8 Place the pump upright on flat surface Reinstall the housing by gently pressing while turning clockwise until hand tight gt 9 Install the ventilation lock and close it turn counter clockwise to CLOSE 10 Pump will work again according to settings error report will be deleted Technical Data Lubricus Controller Con
7. for example M6 not included page 21 version 04 2013 Gruetzner LUBRICUS ome Mounting Lubricus unit 2 srews 6mm for example M6x40 are required for a safe installation of your Lubricus The optimum clamping force of the screw is 5 Nm 3 points at the back assure a safe hold page 22 version 04 2013 Gruetzner LUBRICUS e Recommened tube length Keep in mind For low temperature For stiff grease more than NLGI 2 For difficult applications with high backpressure gt Shorten your tube as much as possible 2 Minimum inner diameter is 4mm gt Avoid reductions of the inner tube 70 gt a r aaa 60 H es H so vo so ee eee low temperature 2 17 7 7 gt stiffgrease o Pil 2 40 17 1 backpressure d L 10 bar De d r a 30 TTT T Z7 without i AE a L T backpressure 20 MMMM r P a Length m Chart Required pressure vs to tube length tested with tubes 6 x 4 mm Disposal When disposing lubricant the waste disposal instructions of the lubricant manufacturer must be observed Disposal of Lubricus Lubrication System observe the regional valid laws and regulations The empty lubricant cartridges contain lubricant remains Please dispose with other oil contaminated garbage Gruetzner GmbH Kohlenhofstr 60 D 90443 N rnberg www lubricus com Tel 49 911 277 399 0 Fax 49 911 277 399 99 page 23 version 04 2013
8. show ON the red LED will still light to signal that an error message exists Root cause The connection cable between Controller and Lubricus unit is broken disconnected or missing Lubricus Controller unit stays active and other connected units will dispense as per program in memory Corrective action Change or connect cable broken missing or disconnected connection cable Switch unit OFF and On again The error message will be reset to 0 Lubricus will start again as per program in memory Example Exit 1 Lubricus LUB C 2 all OK Exit 2 Lubricus LUB C 1 1 cable defect Lin T CEA 88280 e 8 O O O 8 6 F 1 9 F 1 2 OK 3 4 OK System error Switch unit OFF and On again Memory will not be erased Extras Guick check back pressure measurement For testing purposes the Lubricus Controller is equipped with the Quick Check back pressure measuring function Quick Check back pressure measurement uses the extra lubrication cycle A simple touching of the programming key to the sensor pad will measure the existing pressure between the lubrication point and the pump unit exit The value in bar will be shown in the display Example Quick Check function result shown on the display LCb 2 MAX e a 4 a a k a 4 4 l page 17 version 04 2013 4 Gruetzner LUBRICUS om Connector PIN assignment connection Lubricus Controller to Lubricus Lubrication System
9. Basic adjustment will be changed when display blinks ON touch the sensor area with the activation and programming key approx 2 3 sec and hold until the display On disappears red LED then remove programming key Should you have missed the time when On was blinking place programming key on sensor and hold until you see a 3 x red blinking signal red LED OFF in display To switch Unit ON place programming key on sensor and hold until you see a 3 x red blink signal red LED ON in display Programming for each Controller exit The programming mode enables Entering the quantity of exits per Lubricus unit page 10 11 specific settings if no exit is activated A00 gt 2 and 3 are not available Entering H Pause Time Time between 2 lubrication intervals page 12 table pause time adjustment Entering C the lubrication quantity per interval page 12 table quantity adjustment a Lubricus Controller Exit 1 green LED is blinking gt left side of Lubricus body Display shows A00 Enter required pump exits as per your attached Lubricus Model page 10 11 Example Lubricus LUB C 2 Adjustment at green LED left side of Lubricus body 2 Exits A02 Touch sensor shortly with programming key until required information is displayed If there is no change the displayed value will be used After the exit activation the parameters H and C need to be adjusted H Pause time between 2 lubrication cycles Input
10. Lubricus Lubrication System the piston pump starts to work and pumps the lubricant in small quantities to the outlets The integrated microprocessor controls the delivery rates and the operating time which can be individually set Lubricus Controller Installation Lubricus Controller settings Observe the safety instructions The programming mode enables Lubricus will be installed near the lubrication point gt Entering the quantity of exits per Lubricus Install Lubricus Controller in a central location page 12 and page 13 14 specific settings Connect cable gt Entering pause time Time between 2 Switch on lubrication intervals page 12 table pause time adjustment gt Finished gt Entering the lubrication quantity per interval page 12 table quantity adjustment display show s ustment Values and error m ssages E status indicator F red LED indicates Diels system must be checked A OK green d 5 d Ee S E E S 7 1 Ge 4 page 8 version 04 2013 Adjustment Flow chart page 9 Connect Controller with24 LUBRICUS Gr uetzner GmbH Controller shows ON and all basic settings combined with status indicator LEDs Settings for leftside of Lubri us bod orange LED flashing green LED flashing Settings for rigth side of Lubri us bod e ON isflashingfor3 sec gt Change to individuell settings with gt lt f gt Exit 1 H
11. ation System to strong shock loads Store the Lubricus Lubrication System in a cool and dry place to avoid corrosion of the system s individual parts Pay attention to the current safety and accident prevention instructions during the transport Wear suitable protection equipment if necessary Installation instruction The following conditions have to be satisfied during the installation of this Lubricus Lubrication System thus it can be assembled with other parts to a complete machine without affecting the safety and health of humans The housing of the Lubricus and or Lubricus Controller should not be exposed to direct sunlight and or radiant heat preventing the formation of condensation Electrical connection e Have the electric power supply connected only by a trained electrician X e Connection and wiring of the electric components should be done by an expert trained in this field Be Check the voltage details with the existing power supply voltage Maintenance repair Disconnect the voltage feed before starting with maintenance or repair Maintenance and repair work may only be done with the system shut down Check the surface temperature of Lubricus Lubrication System due to danger of burning by radiant heat Always wear heat resistance gloves Protect the system from activation during maintenance and repair work page 7 version 04 2013 Gruetzner LUBR ICUS omy Function Principle When activating the
12. ctive and will pump Corrective action replace cartridge Lubricus will continue to run as per active program Example exit 1 Lubricus LUB C 2 all OK exit 2 Lubricus LUB C 1 1 cartridge empty Lin T cE E 608560 o S a F 1 2 OK 3 4 1 2 e 3 E2 Back pressure too high red LED lights constantly Display will show error for Lubricus unit connected to Lubricus Controller exit E2 the error message is related to the Lubricus body half respectively to the Lubricus exit Root cause Back pressure was measured 3 x too high The lubrication point could be clocked the tube length could be too long or the grease is too stiff or has hardened Lubricus will stop Corrective action Trace reason for high back pressure gt 70bar and correct it Switch unit OFF and On again The error message will be reset to 0 Lubricus will start again as per program in memory Example Exit 2 Lubricus LUB C 1 1 Error 2E2 at exit 2 orange LED right Lubricus body half et page 16 version 04 2013 Gruetzner LUBRICUS e E4 Lubricus feedback Exit was activated but no feedback from connected Lubricus unit red LED lights constantly Display will show error for unit connected to Lubricus Controller exit E4 the red LED will light additionally to the green and orange LED when the seguence of the connected unit with the error is reached If the seguence reaches the Lubricus units without error the display will
13. he Lubricus Lubrication System is only allowed after consultation with the manufacturer Original spare parts and accessories authorized by the manufacturer are for safety purposes Using other parts results in loss of liability for claims resulting out of this For components retrofitted by the operator the manufacturer does not assume guarantee nor claims for damages Prohibited methods of operation Operational security of the Lubricus Lubrication System is only guaranteed if it is operated in accordance with the operating instructions The limit values stated in the technical data must not be exceeded under any circumstances page 6 version 04 2013 Gruetzner LUBRICUS i All components of the system are designed in accordance with the prevailing regulations of the construction of technical machines in regards to operational safety and accident prevention Operation outside of these constraints can lead to dangers for the user respectively third persons or other technical facilities The Lubricus Lubrication System therefore may fulfil only in technically fault free condition its intended use This may only be carried out under compliance of the safety regulations and the attention of the operator s manual Therefore please regularly inspect the pump and its attachments for possible damage or leaks General risk reference Transport and storage Use suitable lifting gear for transport Do not throw or expose the Lubricus Lubric
14. move programming key Display changes to ON Adjustment stays in Memory Ones x T 00 version 04 2013 ma LUBRICUS 3 Malfunction error shown on LCD LED Normal operating mode Lubricus Controller display ON each LED for activated pumps blink shortly one after each other in 1 second intervals Not activated Lubricus Controller exits will not blink Example Lubricus Controller exit 1 Lubricus LUB C 2 Adjustment green LED left Lubricus body 2 exits A02 Adjustment orange LED right Lubricus body 0 exits A00 Lubricus Controller exit 2 Lubricus LUB C1 1 Adjustment green LED left Lubricus body 1 exit A01 Adjustment orange LED right Lubricus body 1 exit A01 Green LED for normal operating mode is always illuminated LED s of Lubricus Controller exit 1 and 2 blink shortly one after each green green arange and starting again from the beginning 2 BE TINTS E OK Error messages faults The dedicated error message for each connected Lubricus unit is displayed E1 Empty lubricant reservoir red LED lights constantly Display will show error for Lubricus unit connected to Lubricus Controller exit E1 when the sequence of the connected pump with the error is reached If the sequence reaches the units without error the display will show ON the red LED will still light to signal that an error message exists Root cause The lubricant cartridge is empty The unit continues to be a
15. n LED Function left side of Lubricus body Normal Status Indication F red LED constant light failure fault error report OK green LED constant light everything OK 1 Connect Lubricus Controller with M12x1 Plug to 24 VDC e g via PLC power consumption max 300 mA more details in communication interface page 18 after connection 24 VDC gt green LED illuminated constant light 2 Lubricus Controller displays ON the display will show all values in the display associated with the assigned LED light Lubricus unit 1 green LED than orange LED Lubricus unit 2 green LED than orange LED Lubricus unit 3 green LED than orange LED Lubricus unit 4 green LED than orange LED nm Lin Basic settings all Controller exits are not activated 3 After displaying all adjustments ON is blinking for approx 3 sec in the display Now you can adjust the basic settings If no further action the N 2 Controller will continue in the In operating mode Place activation and programming d N key in ventilation hole and turn it from OPEN gt CLOSE Open the ventilation lock turn clockwise to OPEN and remove the cover The nose of the cover is your Operating programming key All adjustments and changes will be executed by touching eini the sensor area on the Controller with the activation and E programming key page 13 version 04 2013 CIE LUBRICUS e 4
16. nical and chemical effects Endangering the environment due to leaks of dangerous materials Safety information for operators operating staff e Hot or cold machine parts are hazardous and must be protected from touching The protection on moving or rotating parts must not be removed e In case of leakages of dangerous media proper disposal not endangering environment and people must be ensured e Legal Regulation must be observed and complied Eliminate any danger due to electrical power Safety information for maintenance inspection and assembly work All maintenance inspection and installation work may only be carried out by trained specialists who have been informed appropriately by studying the user information closely All work must only be carried out when machine is shut down and while wearing appropriate protective clothing Always comply with the procedures for shutting the machine down that are described in the operating manual All the safety and protective equipment must be replaced immediately after completing work Environmentally hazardous substances that endanger the environment must be disposed in accordance with local regulations Secure the system during maintenance and repair work against intentional or unintentional operation Dispose of used lubricants in accordance with the safety data sheets of the lubricant manufacturer Alterations and manufacture of spare parts without authority Rebuilding or altering t
17. on System is a very compact lubrication pump for oil and grease up to NLGI 2 The types LUB C 1 LUB C 2 LUB C 3 LUB C 4 and LUB C 1 1 are designed for external control Lubricus Controller and a power supply of 24 VDC The lubricant reservoir 400 cm is located in a cartridge Lubricus Lubrication System Type LUB C 1 LUB C 2 LUB C 3 LUB C 4 and LUB C 1 1 will be installed near the lubrication point Lubricus Controller System Control will be installed in a central location Depending on the configuration of Lubricus Lubrication System Type C is available with up to four outlets and therefore suitable to lubricate several lubrication points Warning Lubricus Lubrication System is designed for use in normal industrial environment indoor as well as outdoor but is not suitable for mounting on moving equipment for example trucks Only use original Lubricus cartridges and original spare parts None original spare parts can destroy the Lubricus Lubrication System or the Lubricus Controller Scope of supply Standard delivery Lubricus Controller includes Lubricus Controller Operating Instructions Standard scope of supply Lubricus Lubrication System Type C Lubricus Lubrication System Type LUB C 1 LUB C 2 LUB C 3 LUB C 4 LUB C 1 1 Tube connector attaches to the outlet suitable for flexible tube 6 x 4 Operating Instructions Lubricus Lubrication System Type C LUB C 1 LUB C 2 LUB C 3 LUB C 4 LUB C 1 1
18. onstant light OK 1 For every Lubricus connected the number of outlets must be programmed Divided into left half green LED and to right orange LED half of the Lubricus body The display shows following Base setting A00 no exit activated A01 1 exit activated A02 2 exits activated Settings for every specific Lubricus Models Type LUB C 1 adjustment at green LED left Lubricus body 1 exit A01 adjustment at orange LED right Lubricus body no exit A00 Type LUB C 2 adjustment at green LED left Lubricus body 2 exits A02 adjustment at orange LED right Lubricus body no exit A00 Gam Left side of Lubricus body dispensing equal quantity from both exits outlets page 10 version 04 2013 page 11 Gruetzner LUBRICUS sing Typ LUB C 3 adjustment at green LED left Lubricus body 1 exit A01 adjustment at orange LED right Lubricus body 2 exits A02 Left exit individual controlled Right side of Lubricus body 2 outlets is dispensing egual guantity OR Typ LUB C 3 adjustment at green LED left Lubricus body 2 exits A02 adjustment at orange LED right Lubricus body 1 exit A01 Right exit individual controlled Left side of Lubricus body 2 outlets is dispensing egual guantity Typ LUB C 4 adjustment at green LED left Lubricus body 2 exits A02 adjustment at orange LED right Lubricus body 2 exits A02 Left and right side of Lubricus body is individual con
19. options 1 to 96 Values in h Table page 12 Short touch of the programming key on the sensor changes the value 1 96 are possible Constant contact will let the display fast forward short contact will advance values by 1 No activity for 2 sec through touching the sensor pad the displayed value will then be used and placed in memory After a short time the unit will switch automatically to C C Number of cycles Number of cycle s x 0 15cm lubrication quantity Input options 1 to 30 table page 12 Short touch of the programming key on the sensor changes the value 1 30 are possible Constant contact will let the display fast forward short contact will advance values by 1 no activity for 2 sec by touching the sensor pad the displayed value will then be placed in memory and will be used This will finish the basic settings of Lubricus Controller Exit 1 left Lubricus body side green LED Automatic change to next Lubricus body half on the same Lubricus Controller Exit page 14 version 04 2013 6 Gruetzner LUBRICUS b Lubricus Controller Exit 1 orange LED is blinking gt right side of Lubricus body Same procedure like a Automatic change to next Lubricus Controller exit 2 3 and 4 see Adjustment Flow chart page 9 c If no further action the unit will continue in the operating mode Place activation and programming key in ventilation hole and turn it from OPEN gt CLOSE d Lubricus Controller will ini
20. sed according to the technical data see chapter technical data Unauthorized structural changes at the Lubricus Lubrication System are not permitted We do not assume liability for damages of persons or machines which result from that Other uses or uses beyond those described above cannot be considered to be in accordance with the regulations Extent of warranty Warranties concerning operating safety reliability and capacity are only granted under the following conditions Assembly installation maintenance and repair are only carried out through trained specialist Hazardous hot or cold machine parts must be shielded to prevent touching Lubricus Lubrication System must be used according to the instructions in the technical operating manual the rated technical data must not be exceeded in any case Retrofitting and repair work on the Lubricus Lubrication System may only be done by manufacturer General safety information Basic information which must be followed during service operation and maintenance are listed as follows It is absolutely essential to read the operator s manual user guide by respective technical staff technical operator before installation and start up In addition to this it must be permanently available at the site IMPORTANT Please pay attention not only to the safety instructions under this main point but also to those special security cautions that are mentioned on the other pages
21. tiate all activated exits The display will change to ON An extra lubrication cycle of 0 15 cc per exit with back pressure measurement Quick check will be performed A value that represents the pressure required to pump the lubricant to the lubrication point will be displayed After the pump cycle is finished the max pressure is shown in bar e g 015 represents 15 bar The unit can only provide approximate values from 15 This is accurate enough to establish the condition of the lubrication point Additional functions QuickCheck extra dispensing cycle pumping of small amounts of lubricant for testing purposes Touch contact sensor of Lubricus Controller with programming key and count 2 x red blinking signal central LED in the display amp bai 1 2 F 3 4 OK Additional functions Switch OFF Touch contact sensor of Lubricus Controller with programming key and count 3 x red blinking signal central LED in the display and remove programming key Display changes to OFF Adjustment stays in Memory A longer contact of the programming key with the sensor does not switch the unit off preventing accidental stopping when a strong magnet is near the of Lubricus Controller ND O O n 00 Co gt OFF 7 Additional functions Switch ON To switch the unit ON Touch contact sensor of Lubricus Controller with page 15 programming key and count 3 x red blinking signal central LED in the display and re
22. trol micro processor controlled up to 4 Lubricus units Type C can be connected Power supply 24 VDC Power consumption max 300mA typical lt 200mA Temperature range 20 C to 80 C Dimensions max g Width x height x depth 130 x159x35 mm Connector M12x1 4 pole power supply and connection to a PLC possible 4 Lubricus connection to Controller M8 x 1 Protection class IP 55 Mounting mounting wholes 6 6mm page 20 version 04 2013 Gruetzner LUBR ICUS Te Technical Data Lubricus Type C 136 Se Se Ee Set a ala oan vn ochlauchanschluls ochlauch 6 connection tube bid abh ngig van ochlauchanschlussteil Starker WH Sed according to tube fittings connector fH 2x4 Storage volume cartridge 400cm Lubricant oil or grease up to NLGI 3 Function principle piston pump Delivery rate per interval 0 15 cm Number of outlets up to 4 Connection high pressure tube 6 x 4 flexible tube with outer diameter 6mm outside and 4mm inside diameter Operating pressure max 70 bar Operating temperature 20 C to 80 C Dimensions max Width x height x depth 112 x 196 x 94 mm Weight without lubricant 1120g Control Lubricus Controller Level monitoring integrated reedcontact Connector M12 x 1 4 pole for connection with Lubricus Controller Protection class IP 65 Combination with progressive systems possible Mounting Lubricus Controller Mounting requires 2 screws
23. trolled Mix of 2x different dispensing guantities Right side of Lubricus body 2 outlets is dispensing egual guantity Left side of Lubricus body 2 outlets is dispensing equal quantity Typ LUB C 1 1 adjustment at green LED left Lubricus body 1 exit A01 adjustment at orange LED right Lubricus body 1 exit A01 Left and right side of Lubricus body is individual controlled version 04 2013 Gr uetzner GmbH LUBRICUS 2 If exits are activated A01 or A02 each side of Lubricus body half can be adjusted H Pause Time gt Time interval between 2 lubrication intervals 1 to 96 h possible than C Lubrication quantity per interval gt 1 x 0 15 cm to 30 x 0 15 cm 4 5 cm possible H Pause Time H Adjustment for Lubricus 1 side of body Intermediate steps are possible C Lubrication quantity per interval c Adjustment for Lubricus 1 side of body Intermediate steps are possible page 12 version 04 2013 Gruetzner LUBRICUS om Start up Switch on Switch off Change Lubricus Controller can be adjusted without any Lubricus unit attached Settings will stay in memory Lubricus Controller controls the connected Lubricus in sequence one after the other This ensures no Lubricus unit is operating parallel preventing higher energy usage During pump operation no further changes and functions are possible a orange LED Function right side of Lubricus body 4 a gree
Download Pdf Manuals
Related Search